Register your product and get support at www.philips.com/welcome 55PFL7705DV 46PFL7705DV 40PFL7705DV EN: For further assistance, call the customer support service in your country. • To obtain assistance in the U.S.A., Canada, Puerto Rico, or the U.S.Virgin Islands, contact Philips Customer Care Center at 1-866-309-0841 • To obtain assistance in Mexico, contact Philips Customer Care Center at 01 800 504 62 00 Enter below the model and serial numbers located on the back and right side of the TV cabinet.
1 Notice 2 Important Product information Screen care Environmental care Regulatory notices 3 Your TV Side controls and indicators Remote control 4 Get started Supplied accessories Mounting stand onto TV for 40” and 46” Positioning the TV Adjusting the swivel angle Installing the remote control batteries Connecting the antenna or cable Managing cables Connecting the AC power cord Switching on and initial setup 5 Use your TV Switching on your TV and putting it in standby mode Switching channels Adjusting v
Return your Product Registration Card or register online at www.philips.com/welcome today to get the very most from your purchase. Registering your model with PHILIPS makes you eligible for all of the valuable benefits listed below, so don't miss out. Complete and return your Product Registration Card at once, or register online at www.philips.
1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
1 Notice 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
® Kensington and Micro Saver are registered US trademarks of ACCO World corporation with issued registrations and pending applications in other countries throughout the world. Environmental care English VESA, FDMI and the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association. The packaging of this product is intended to be recycled. Contact your local authorities for information about how to recycle the packaging.
3 Your TV Remote control Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome Side controls and indicators a s b r c q d e e p d g h c a f o i b j a Standby indicator / Remote control sensor n b . POWER Switches the TV on or puts it in standby mode. The TV is not powered off completely unless it is physically unplugged.
r AUTO MODE Cycles through preset picture and sound settings. (See ‘Using auto mode’ on page 24.) b FAV Displays a list of all channels marked as favorite. (Includes subchannels) s OPTIONS Displays a list of menu items applicable to the highlighted object or screen. c SLEEP Sets a delay after which the TV switches to standby. d Color buttons (red / green / yellow / blue) Selects tasks or options. e SOURCE Selects connected devices. f NET TV Displays the Net TV menu.
4 Get started Warning Supplied accessories • • • • • • • • • Positioning the TV • Do not insert the AC power cord into the power socket outlet before all the connections are made. Remote Control 2 x AAA, 1.
3 Slide the battery cover off the back of the remote control. Insert the 2 supplied batteries (AAA, 1.5V). Be sure the + and − ends of the batteries line up with the markings inside the case. Slide the cover back into position. If you connect a set-top box through RF IN / OUT If the TV is connected to a cable box or satellite set-top box via a coaxial connection, set the TV to channel 3 or 4, or to the channel specified by the service provider.
Managing cables Route your antenna cable and all other cables through the cable management tie at the back of the TV. The holder helps keep your cables tidy and easily manageable. Connecting the AC power cord Warning • Verify that your power voltage corresponds with the voltage printed at the back of the TV. Do not insert the AC power cord if the voltage is different. 1 Attach the cable management tie as illustrated below. 1 2 3 Locate the power connector at the back of the TV.
Before you switch on the TV, check that the AC power cord is properly connected. Press . POWER at the right side of the TV, or press . (standby-On) on the remote control. The TV normally takes 25-30 seconds to start up and the following screen appears the first time you turn on the TV. Select [ Picture A] or [ Picture B] by pressing Í / Æ that is the most pleasing to you, then press OK. You see 5 different pictures to be completed.
5 Use your TV Switching channels This section helps you perform basic TV operations. Switching on your TV and putting it in standby mode To switch on • Press . POWER at the side of the TV or press . (standby-On) on the remote control. To switch to standby • Press . POWER at the side of the TV or press . (standby-On) on the remote control again. Note • Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy.
Watching channels from a set-top box To watch channels from a set-top box 1 Switch on the set-top box. » The picture from your set-top box might appear automatically on the TV screen. 2 Use the remote control of your set-top box to select channels. If the picture does not appear 1 2 Press SOURCE repeatedly to select the set-top box and wait a few seconds for the picture to appear. Use the remote control of your set-top box to select channels.
6 Use more of your TV • • 5 Access TV menus If device lock is unlocked, [Device lock] will be displayed. If device lock is locked, [Device unlock] will be displayed. will be displayed at the top right When device lock is locked, of the device icons. Enter your PIN. (See ‘Setting your PIN’ on page 26.) • Once you have set PIN, PIN input menu does not appear after the unit is turned on. Menus help you to install channels, change picture and sound settings then access other features.
Specifics You can project high definition (HD) or standard definition (SD) video, depending on the processing power of your PC. The content protection on most DVD or Blu-ray Disc movies might restrict watching the movie on TV when the disc is playing on a PC. The TV shows PC media files with a small delay. Philips Wireless MediaConnect is only available for PC. PC requirements Windows XP, Windows Vista, Windows 7 (PC only) Minimum PC requirements • Intel Core 2 Duo 1.
Enjoying internet radio with vTuner 3 With this unit, you can enjoy internet radio with vTuner via the internet. In order to listen to internet radio, you must connect this unit to the internet. For the network connection, see ‘Connecting the TV to the internet using an Ethernet cable’ or ‘Connecting the TV to the internet using a USB wireless LAN adapter’ on page 41. For the network setup, see ‘Network’ on page 30. e.g.) Location vTuner |...| Sunhall Internet radio playback All Stations 45 ..
Guide to the playback screen Remove from favorite list e.g.) Location 1 2 3 1 vTuner |...| Sunhall All Stations 45 ..
VUDU operations With this unit, you can enjoy VUDU HD on-demand movies /TV shows and internet applications. - For complete instructions on using VUDU service, please visit www.vudu.com/docs to view an updated in-depth online manual. Guide to VUDU menu screen App Home Screen App Home Screen is the entry point to VUDU applications including VUDU movies. To call up the screen, press NET TV on the remote control and then use Î / ï /Í / Æ to select [vudu].
Using internet applications After activating this unit, you are ready to purchase or rent movies /TV shows and watch directly on your TV. In addition to VUDU movies, you can use various kinds of internet applications. 1 2 3 4 5 6 Press NET TV on the remote control and then use Î / ï /Í / Æ to select [vudu]. Use Î / ï / Í / Æ to select [VUDU movies], then press OK. • VUDU movies home screen will appear. Use Î / ï / Í / Æ to select [Most Watched] , [New on Vudu] or [Explore Catalog], then press OK.
Using Twitter Guide to Twitter menu screen You can view your Twitter feeds and more using the Twitter application on this unit. - For more details about Twitter, please visit www.twitter.com Before Logging in to Twitter Twitter Home Screen Twitter Home Screen consolidates browsing of tweets and some functional menus for Twitter. To call up the screen, press NET TV on the remote control and then use Î / ï /Í / Æ to select [ Twitter]. Single View Follow the procedure below before logging in to Twitter.
Viewing Trends on Twitter Your TV displays the logged in user's favorites on Twitter. Trends show topics trending in your area. 1 2 1 2 Follow steps 1 to 2 in ‘Viewing tweets on the TV’ on page 20. Use Î / ï to select [Favorite], then press OK. • If you have no favorites, [ TV was not able to acquire the Tweet.] will appear. Displaying Mentions on Twitter English Viewing Favorites on Twitter Follow steps 1 to 2 in ‘Viewing tweets on the TV’ on page 20. Use Î / ï to select [ Trends], then press OK.
Changing picture and sound settings You must set [Home] in [ Location]. (Refer to page 30.) Otherwise, personalized picture and sound settings will not be memorized after the unit goes to standby mode. Setting items Active control Description Off Sets Active control to off. On with Light Sensor Adjusts backlight for the best picture quality by dynamically adjusting the backlight intensity in accordance with lighting condition in the room.
Changing picture format 2 Press FORMAT on the remote control. English 1 For 4:3 video signal [Automatic] [Super zoom] [4:3] [Wide screen] [Movie expand 16:9] [Movie expand 14:9] Use Î / ï to select a picture format and press OK to confirm your choice. Summary of picture formats Display modes can be selected when the broadcasting station is sending 16:9 or 4:3 video signal. And 3 types of display modes can be selected for PC input signal.
Using your TV as a PC monitor Setting items Use a VGA connector to connect a PC to your TV. For sound, add an audio cable with a stereo mini jack. SRS TruSurround HD On Off Caution • Before you connect your PC, set the PC monitor refresh rate to 60Hz.
Create or edit a list of favorite channels Setting the time manually 1 1 4 5 6 Use Î / ï to highlight a list, and then press OK to select the list. Press OPTIONS to enter edit mode. » A list of channels is shown. Use Î / ï to highlight a channel. Press OK to select or deselect the highlighted channel. » The channel is added to or removed from the list of favorite channels. Press MENU to exit.
Difficulties viewing closed captions on DTV programming If you have difficulties viewing closed captions on DTV programming, including HDTV, received from your subscription television provider, you should : • consult any consumer information and manuals / guides on closed captions for DTV programming provided by your subscription television provider; • ensure that the captioning function on your set-top box, if applicable, is turned on; and, • ensure that the captioning function on your DTV is turned on.
This section describes how to lock input sources or specified channels. The channels can be selected but the screen is blanked out and the audio is muted. 1 2 3 Press MENU on the remote control and then use Î / ï /Í / Æ to select [Setup] > [Features] > [Child lock]. Enter your PIN. (See ‘Setting your PIN’ on page 26.) Use Î / ï to select [Channel Lock], then press OK. Caption settings Lock Lo ck after aft aft fter er Sleeptimer TV ratings lock P TV-Y Movie ratings lock P TV-Y7 Canada English rati..
Using the movie ratings lock Summary of Canada English ratings lock You can control viewing of movies based on their MPAA (Motion Picture Association of America) rating. Rating Description All E C All items in the ratings list are locked. Exempt program. Programming suitable for children under the age of 8 years. No profanity or sexual content of any level allowed. Minimal comedic violence. Suitable for children ages 8 and over. Low intensity violence and fantasy horror allowed.
EasyLink You can use demonstrations to better understand the features of your TV. This function allows you to operate the linked functions between our brand devices with EasyLink capabilities and this unit connected via a HDMI cable. 1 2 3 4 Press MENU on the remote control and then use Î / ï /Í / Æ to select [ Setup] > [ Features] > [ Demo]. Also, you can enter the demo mode when you press DEMO . 1 Use Î / ï to highlight a demo, and press OK to start the demo.
Set your location to home Wireless network This menu is displayed only when you set [Wireless] in [Network selection]. You can set the location of your TV to [Home] or [Retail store]. Choosing [Home] gives you full flexibility to change predefined settings for picture and sound. In order to use a wireless network, you must set up a connection to the Wireless LAN Access Point (AP) (e.g. wireless router).
Wireless network setting (Manually enter your SSID) 1 2 Press MENU on the remote control and then use Î / ï /Í / Æ to select [Setup] > [Installation] > [Network] > [Wireless network] > [Wireless network setting] > [Manually enter your SSID]. • Wireless LAN Access Point (AP) (e.g. wireless router) Name (SSID) entry screen will appear. Enter the wireless network name (SSID) using Î / ï /Í / Æ, then press OK. [Clear] : Clear the entered number or word. [All clear] : Clear all the entered numbers or words.
DivX® Video on demand Setting status You can check the status of network settings. 1 2 Press MENU on the remote control and then use Î / ï /Í / Æ to select [Setup] > [Installation] > [Network] > [Setting status]. • Network setting list will be displayed. • MAC address of this unit will be displayed in the list. Press MENU to exit. Disclaimer Displays the network service disclaimer.
Caution • This unit accepts USB flash memory only. Other storage devices such as external HDD by USB bus power will not work. Connect a USB storage device 1 2 3 • Philips is not responsible if the USB storage device is not supported nor is it responsible for damage or loss of data from the device. Your TV is fitted with a USB connection that enables you to view photos or listen to music stored on a USB storage device.
Description Watch your Video on a USB storage device None No effect when switching images. Dissolve Overlaps a next image on a current image. Wipe right Pushes a current image out from left. 1 2 Wipe left Pushes a current image out from right. Wipe up Pushes a current image out from bottom. Setting items Transitions *1 Rotate *2 Zoom * 2 A next image comes into the center from out. Box out A next image goes to the out from center. 0 Displays an image at its original direction.
7 Install channels The first time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available). This chapter provides instructions on how to reinstall and fine-tune channels. 1 Press MENU on the remote control and then use Î / ï /Í / Æ to select [Setup] > [Installation] > [Language]. Language Picture Sound This function lets you add the channels that were not added by the autoprogram due to the receptible condition at the initial setup.
8 Update your TV software Philips continuously tries to improve its products and we strongly recommend that you update the TV software when updates are available. New software can be downloaded from our website at www.philips.com using the model number of your TV (e.g. 55PFL7705DV) to find information. Updating software USB update You can update the software by using USB storage device. 1 2 If the TV is on, press . POWER at the side of the TV.
Network update 2 3 4 5 6 English You can update the software by connecting the unit to the internet. 1 Follow steps 1 to 2 in ‘Connection Test’ on page 30. Press MENU on the remote control and then use Î / ï / Í / Æ to select [Setup] > [Software Update] > [Updates] > [Network]. Use Í / Æ to select [Yes], then press OK. • This unit will then start checking for the latest firmware version. Confirmation message will appear. Use Í / Æ to select [Yes], then press OK.
9 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start Guide. Connection overview e f g h SERVICE ONLY PC-IN RGB i * j a k b l c d a PC input jack VGA cable connection for PC. h HDMI 3 input jack Third HDMI in connector. b Digital audio output jack Digital audio output to home theaters and other digital audio systems. i HDMI 2 input jack Second HDMI in connector.
English Selecting your connection quality HDMI - Highest quality Supports high-definition signals and gives highest picture and sound quality. Video and audio signals are combined in one cable. You must use HDMI for full high-definition video and to enable Philips EasyLink. Note • Philips HDMI supports HDCP (High-bandwidth Digital Contents Protection). HDCP is a form of Digital Rights Management that protects high definition content in DVD or Blu-ray Discs.
Connecting your devices Connecting a set-top box, DVD player / recorder via component video connectors (YPbPr) and analog audio This section describes how to connect a selection of devices with different connectors. Different types of connectors can be used to connect a device to your TV. The following sections describe examples only, other configurations are possible.
Connecting the TV to the internet using a USB wireless LAN adapter English Connecting a set-top box via a composite connector and analog audio WAN Wireless LAN Access Point (AP) (e.g. wireless router) USB wireless LAN adapter IN AUDIO L/R + VIDEO Internet Cable LAN OUT RF IN Set-top box Ethernet cable Network equipment (modem, etc.) Note Note • Only the left loudspeaker reproduces sound for mono equipment.
Add devices Connecting a PC If you connect a PC with a VGA connector at the back. After connecting devices, assign the device attached to each connector. This allows you to easily identify devices connected to your TV. 1 AUDIO IN 2 3 4 AUDIO OUT Use Í / Æ to select [Start], then press OK. Use Î / ï to select a device and press OK. Use Î / ï to select the connector your device is connected to and press OK. 5 If there is video and audio output, press OK.
Problem Possible cause and solution No power or indicator light. The TV is not connected to the power. Press . POWER at the side of the TV or on the remote control. Ensure that the AC power cord is connected tightly to the TV power connector and to the power socket outlet. Remove the AC power cord from the power socket outlet, wait 60 seconds and reconnect the AC power cord. Connect the TV to a different power socket outlet. No picture or sound is detected from the device using HDMI 1-4 input jack.
11 Specifications Note • Specifications are subject to change without prior notice.
English 13 Warranty LIMITED WARRANTY ONE (1) YEAR WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
14 Index A Antenna, connect Audio Audio setting Auto mode Auto TV on Auto volume leveling N Netflix Network 9 24 24 24 29 24 P PC Philips Wireless MediaConnect Picture format Picture settings R C Cables component composite connection quality HDMI manage cables YPbPr Channels install lock Child lock channel lock PIN ratings lock Clock Closed caption Connections Controls Customer support service D Device List Device lock E EasyLink ENERGY STAR® Environmental care Equalizer F FAV 39 39 39 39 10
P&F USA, Inc. PO Box 430 Daleville, IN 47334-0430 P&F Mexicana, S.A. de C.V. Av. La Palma No. 6, Col. San Fernando La Herradura, Huixquilucan Edo. de México C.P. 52787 TELEVISOR A COLOR DE CRISTAL LIQUIDO (LCD) MODELO LCD IMAGEN VISIBLE ENERGIA 55PFL7705DV/ F7 55”(139,70cm) 138,78cm 120V ~ 60Hz 200W 46PFL7705DV/ F7 46”(116,84cm) 116,81cm 120V ~ 60Hz 165W 40PFL7705DV/ F7 40”(101,60cm) 101,60cm 120V ~ 60Hz 155W Comercializado por : P&F MEXICANA, S.A. DE C.V.
