Register your product and get support at www.philips.com/welcome 55PFL7505D 46PFL7505D 40PFL7505D EN: For further assistance, call the customer support service in your country. • To obtain assistance in the U.S.A., Canada, Puerto Rico, or the U.S.Virgin Islands, contact Philips Customer Care Center at 1-866-309-0841 • To obtain assistance in Mexico, contact Philips Customer Care Center at 01 800 504 62 00 Enter below the model and serial numbers located on the back and right side of the TV cabinet.
1 Notice 4 2 Important 5 5 5 5 5 Product information Screen care Environmental care Regulatory notices 3 Your TV Side controls and indicators Remote control 4 Get started Supplied accessories Mounting base onto TV for 40” and 46” Positioning the TV Adjusting the swivel angle Installing the remote control batteries Connecting the antenna or cable Managing cables Connecting the AC power cord Switching on and set up the TV 5 Use your TV Switching your TV on or to standby Switching channels Adjusting vol
Return your Product Registration Card or register online at www.philips.com/welcome today to get the very most from your purchase. Registering your model with PHILIPS makes you eligible for all of the valuable benefits listed below, so don't miss out. Complete and return your Product Registration Card at once, or register online at www.philips.
1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
1 Notice 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
Environmental care English 2 Important Registering your model with Philips makes you eligible for all of the valuable benefits listed below, so don’t miss out. Complete and return your Product Registration Card at once, or register online at www.philips.com/welcome to ensure : • • • Proof of Purchase Returning the enclosed card guarantees that your date of purchase is on file, so no additional paperwork is required from you to obtain warranty service.
3 Your TV Remote control Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome Side controls and indicators a s b r c q d e e p d g h c a f o i b j a Standby indicator / remote control sensor n b . POWER Switches the TV on or off. The TV is not powered off completely unless it is physically unplugged. m c CHANNEL + / − Switches to the next or previous channel.
r AUTO MODE Cycles through the preset picture and sound setting (see ‘Using auto mode’ on page 17). b FAV Displays a list of all channels marked as favorite. (Includes subchannels) s PIXEL PLUS Displays the Active control menu. English a . (Standby-On) Switches the TV on or off. The TV is not powered off completely unless it is physically unplugged. c SLEEP Sets a delay after which the TV switches to standby. d Color buttons (red / green / yellow / blue) Selects tasks or options.
4 Get started Supplied accessories • • • • • • • Remote control 2 x AAA, 1.5V batteries M4 x 10 double sems screw x 4 (available for 40” and 46” only) AC Power cord Cable management tie User manual Quick Start Mounting base onto TV for 40” and 46” In addition to reading and understanding the safety instructions, consider the following before positioning your TV : • Ensure that you always have easy access to the AC power cord or plug to disconnect the TV from the power.
Connecting the antenna or cable If you connect a set-top box through RF IN / OUT English If the TV is connected to a cable box or satellite set-top box via a coaxial connection, set the TV to channel 3 or 4, or to the channel specified by the service provider. Cable If you connect to an antenna Any DTV programs that are broadcast in your area can be received for free through an antenna connection.
Managing cables Route your antenna cable and all other cables through the cable holder at the back of the TV. The holder helps keep your cables tidy and easily manageable. Connecting the AC power cord Warning • Verify that your power voltage corresponds with the voltage printed at the back of the TV. Do not insert the AC power cord if the voltage is different. 1 Attach the cable holder as illustrated below. 1 2 3 Locate the power connector at the back of the TV.
Before you switch on the TV, check that the AC power cord is properly connected. Press . POWER at the right side of the TV, or press . (Standby-On) on the remote control. The TV normally takes 25-30 seconds to start up and the following screen appears the first time you turn on the TV. Select [Picture A] or [ Picture B] by pressing Í or Æ that is the most pleasing to you, then press OK. You see 5 different pictures to be completed.
5 Use your TV Switching channels This section helps you perform basic TV operations. Switching your TV on or to standby To switch on • Press . POWER at the side of the TV or press . (Standby-On) on the remote control. To switch to standby • Press . POWER at the side of the TV or press . (Standby-On) on the remote control again. Note • Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy. Your TV has a very low standby power consumption.
Watching channels from a set-top box To watch channels from a set-top box 1 Switch on the set-top box. » The picture from your set-top box might appear automatically on the TV screen. 2 Use the remote control of your set-top box to select channels. If the picture does not appear 1 2 Press SOURCE repeatedly to select the set-top box and wait a few seconds for the picture to appear. Use the remote control of your set-top box to select channels.
6 Use more of your TV Lock or unlock your device from the home menu This section describes how to lock or unlock specified device. 1 2 3 4 Access TV menus Menus help you to install channels, change picture and sound settings then access other features. Access the home menu 5 The home menu gives you easy access to connected devices, picture and sound settings as well as other useful features. Press MENU on the remote control. Use Î / ï / Í / Æ to select a device to lock or unlock.
You must set [Home] in [ Location] (refer to page 23). Otherwise, the settings you adjusted will not be memorized after you turn off the unit. Setting items Active control Description Off Sets Active control to off. On with Light Sensor Adjusts backlight for the best picture quality by incoming the video signal and accordance with lighting condition in the room. On without Adjusts backlight for the best picture quality by Light incoming the video signal.
Changing picture format 1 2 For 4:3 (480i, 480p) video signal Press FORMAT on the remote control. [Automatic] [Super zoom] [Wide screen] [4:3] [Movie expand 16:9] [Movie expand 14:9] Use Î or ï to select a picture format and press OK to confirm your choice. Summary of picture formats Display modes can be selected when the broadcasting station is sending 16:9 or 4:3 video signal. And 3 types of display modes can be selected for PC input signal.
Setting items Use a VGA connector to connect a PC to your TV. For sound, add an audio cable with a stereo mini jack. SRS TruSurround HD On Off Caution • Before you connect your PC, set the PC monitor refresh rate to 60Hz.
Create or edit a list of favorite channels Setting the time manually 1 1 2 3 4 5 6 Press FAV V on the remote control to display your lists of favorite channels. Use Î or ï to highlight a list, and then press OK to select the list. Press OPTIONS to enter edit mode. » A list of channels is shown. Use Î or ï to highlight a channel. Press OK to select or deselect the highlighted channel. » The channel is added to or removed from the list of favorite channels. Press MENU to exit.
• • • If you have difficulties viewing closed captions on DTV programming, including HDTV, received from your subscription television provider, you should : • • • consult any consumer information and manuals / guides on closed captions for DTV programming provided by your subscription television provider; ensure that the captioning function on your set-top box, if applicable, is turned on; and, ensure that the captioning function on your DTV is turned on.
Locking a channel Lock after P All All Channel Lock P None TV ratings lock P TV-Y Enter your PIN (see ‘Setting your PIN’ on page 19). Movie ratings lock P TV-Y7 Use Î or ï to select [Channel Lock] k , then press OK. Canada English rati... P TV-G Canada French ratin... P TV-PG This section describes how to lock specified channels. The channels can be selected but the screen is blanked out and the audio is muted.
Summary of Canada English ratings lock You can control viewing of movies based on their MPAA (Motion Picture Association of America) rating. Rating Description All E C All items in the ratings list are locked. Exempt program. Programming suitable for children under the age of 8 years. No profanity or sexual content of any level allowed. Minimal comedic violence. Suitable for children ages 8 and over. Low intensity violence and fantasy horror allowed. Movies with a mild content, suitable for all ages.
Use the demo mode EasyLink You can use demonstrations to better understand the features of your TV. This function allows you to operate the linked functions between our brand devices with a EasyLink feature and this unit connecting through an HDMI cable. 1 2 3 4 Press MENU on the remote control and then use Î / ï / Í / Æ to select [ Setup] > [ Features] > [ Demo]. Also, you can enter the demo mode when you press DEMO . 1 Use Î or ï to highlight a demo, and press OK to start the demo.
You can set the location of your TV to [Home] or [Retail store]. Choosing [Home] gives you full flexibility to change predefined settings for picture and sound. 1 2 3 Press MENU on the remote control and then use Î / ï / Í / Æ to select [Setup] > [Installation] > [Preferences] > [Location]. Deregistrate 1 2 3 Select [Home] and then press OK to confirm your choice. Press MENU to exit. Note will not be memorized after you turn off the unit.
Connect a USB storage device View your picture on a USB storage device 1 2 1 2 3 Turn on the TV. Connect the USB storage device to the USB port on the side of your TV. Use Î / ï / Í / Æ to select [Browse USB]. • Press OPTIONS to display the optional menu, then press OK to switch between [List] and [Thumbnails]. Picture Video Picture001.jpg Pict Pi ctur ure0 e001 01.j.jjpg Picture002.jpg Music Picture003.jpg 2009/09/08 Video Picture001.
Watch your Video on a USB storage device 1 2 1 2 In the USB content browser, use Î/ ï to select [Music]. Press Î or ï to select a file or a folder on the USB storage device. Track1.mp3 Trac Tr ack1 k1.m .mp3 p p3 Picture In the USB content browser, use Î/ ï to select [Video]. Press Î or ï to select a file or a folder on the USB storage device. Video1.divx Vide Vi deo1 o1.d .div ivxx Picture Video2.mpg Track2.mp3 Music Music Video 3 Press OK or F to play the selected files.
7 Install channels Weak channel installation The first time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available). This chapter provides instructions on how to reinstall and fine-tune channels. Press MENU on the remote control and then use Î / ï / Í / Æ to select [Setup] > [Installation] > [Language].
Updating software You can update the software by using USB storage device. Philips continuously tries to improve its products and we strongly recommend that you update the TV software when updates are available. New software can be downloaded from our website at www.philips.com using the type number of your TV (e.g. 55PFL7505D) to find information. 1 2 If the TV is on, press . POWER at the side of the TV to switch off the TV.
9 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start. e f g SERVICE ONLY PC-IN RGB h * i a j b k c d Connection overview a PC input jack VGA cable connection for PC. h HDMI 2 input jack Second HDMI in connector. b digital audio output jack Digital audio output to home theaters and other digital audio systems. i HDMI 1 input jack First HDMI in connector.
English Selecting your connection quality HDMI - Highest quality Supports high-definition signals and gives highest picture and sound quality. Video and audio signals are combined in one cable. You must use HDMI for full high-definition video and to enable Philips EasyLink. Note • Philips HDMI supports HDCP (High-bandwidth Digital Contents Protection). HDCP is a form of Digital Rights Management that protects high definition content in DVD or Blu-ray Discs.
Connecting your devices Connecting a set-top box, DVD player / recorder via component video connectors (YPbPr) and analog audio This section describes how to connect a selection of devices with different connectors. Different types of connectors can be used to connect a device to your TV. The following sections describe examples only, other configurations are possible.
Connecting a PC If you connect a PC with a VGA connector at the back. AUDIO IN English Connecting a set-top box via a composite connector and analog audio AUDIO OUT IN AUDIO L/R + VIDEO VGA IN PC CABLE CABL RF IN OUT OUT RF OUT Set-top box RF IN If you connect a PC with a HDMI-DVI connector. Note • Only the left loudspeaker reproduces sound for mono equipment. Use a mono to stereo adapter (not supplied) for sound reproduction via all internal loudspeakers.
Add devices After connecting devices, assign the device attached to each connector. This allows you to easily identify devices connected to your TV. 1 2 3 4 5 Press MENU on the remote control and then use Î / ï /Í / Æ to select [Add new devices]. Use Í or Æ to select [Start], then press OK. Use Î or ï to select a device and press OK. Use Î or ï to select the connector your device is connected to and press OK. If there is video and audio output, press OK.
Problem Possible cause and solution No power or indicator light. The TV is not connected to the power. Press . POWER at the side of the TV or on the remote control. Ensure that the AC power cord is connected tightly to the TV power connector and to the power socket outlet. Remove the AC power cord from the power socket outlet, wait 60 seconds and reconnect the AC power cord. Connect the TV to a different power socket outlet. No picture or sound is detected from the device using HDMI 1-4 input jack.
11 Product information Power Power requirements : Note Product information is subject to change without prior notice.
English 12 Warranty LIMITED WARRANTY ONE (1) YEAR WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
13 Index A Antenna, connect Audio Audio Setting Auto mode Auto TV on Auto volume leveling P 9 17 17 17 22 17 C Cables component composite connection quality HDMI Manage cables YPbPr Channels install lockk Child lock Channel lock PIN ratings lockk Clockk Closed caption Connection Customer support service D Device List Device lockk E EasyLinkk ENERGY STAR® Environmental care Equalizerr F FAV V 29 29 29 29 10 29 26 20 20 19 19, 20, 21 18 18, 19 9, 28, 30 5 22 14 22 4, 11 5 17 17, 18 H Home mod
P&F USA, Inc. PO Box 430 Daleville, IN 47334-0430 P&F Mexicana, S.A. de C.V. Av. La Palma No. 6, Col. San Fernando La Herradura, Huixquilucan Edo. de México C.P. 52787 TELEVISOR A COLOR DE CRISTAL LIQUIDO (LCD) MODELO LCD IMAGEN VISIBLE ENERGIA 55PFL7505D/ F7 55”(139,70cm) 138,78cm 120V ~ 60Hz 200W 46PFL7505D/ F7 46”(116,84cm) 116,81cm 120V ~ 60Hz 165W 40PFL7505D/ F7 40”(101,60cm) 101,60cm 120V ~ 60Hz 155W Comercializado por : P&F MEXICANA, S.A. DE C.V. IMPORTADOR : SOJITZ MEXICANA, S.A.
