Momentum 559M1 OK VOL www.philips.
Table of Contents 1. Important �������������������������������������� 1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the display ��������������� 5 2.1 Installation ������������������������������������ 5 2.2 Operating the display ���������������� 8 2.
1. Important 1. Important This electronic user’s guide is intended for anyone who uses the Philips display. Take time to read this user manual before you use your display. It contains important information and notes regarding operating your display.
1. Important degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty. • Do not knock or drop the monitor during operation or transportation. • The USB Type-C port could only be connected to specify equipment with fire enclosure in compliance with IEC 62368-1 or IEC 60950-1. • If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-pin outlet.
1. Important that falls within the following temperature and humidity ranges. • For transportation information, please refer to “Technical Specifications”. • Do not leave your monitor in a car/ trunk under direct sun light.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the display 2 Package contents 2. Setting up the display Momentum 559M1 2.1 Installation OK VOL Quick Start 1 Unpacking 1. Open the the top flap and remove clips on the bottom of the package. Register your product and get support at www.philips.com/welcome Monitor User’s Manual 使用产品前请阅读使用说明 Contents: User’s Manual Drivers 2 02 rsi on 保留备用 Vic Ch in a P TO . Ve 1© tm es Power *HDMI ll r igh ts re s e rv e d.
2. Setting up the display 4 Connecting to your PC Connect to PC 1. Connect the power cord to the back of the display firmly. 2. Turn off your computer and unplug its power cable. 1 2 3 4 5 6 7 8 9 10 11 12 3. Connect the display signal cable to the video connector on the back of your computer. 13 Fast Charger 4. Plug the power cord of your computer and your display into a nearby outlet. 5. Turn on your computer and display. If the display displays an image, installation is complete.
2. Setting up the display This will then keep the USB power and charging functions active even when the monitor is in sleep/standby mode. he remote control is powered by 7 T two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Align the batteries according to the (+) and (–) indications inside the battery compartment. 3.
2. Setting up the display 2.2 Operating the display 1 Description of the control buttons Press to switch power on. Press more than 3 seconds to switch power off. Access the OSD menu. Confirm the OSD adjustment. Change the Sound Mode. Adjust the OSD menu. Change the signal input source. Adjust the OSD menu. SmartImage Game menu. There are multiple selections: Xbox, FPS, Racing, RTS, Gamer 1, Gamer 2, Movie, Economy, LowBlue Mode, SmartUniformity, Off.
2. Setting up the display 2 Description of the remote control buttons 4 Change the signal input source. 5 Adjust the OSD menu/ Turn up the values. 6 Adjust the OSD menu / Return to previous OSD level. 7 Confirm the OSD adjustment. 8 Access the OSD menu. Confirm the OSD adjustment. 9 9 Adjust the OSD menu / Turn down the values. 12 10 Access Sound Mode menu. 11 SmartImage Game menu.
2. Setting up the display 3 EasyLink (CEC) Note 1. The EasyLink-compliant device must be switched on and selected as the source. What is it? HDMI is a single cable to carry both picture and audio signals from your devices to your monitor, saving you from cable clutter. It carries uncompressed signals, ensuring that you have the highest quality from source to screen. HDMI-connected monitors with Philips EasyLink (CEC) allow you to control functions of multiple connected devices with one remote control.
2. Setting up the display The OSD Menu Note Xbox: Level up your gaming experience while playing Xbox games, you can even control the connected Xbox console using the remote control. Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. Main menu Ambiglow 5 Resolution notification This display is designed for optimal performance at its native resolution, 3840 x 2160.
2. Setting up the display 7 Ideal setting position for optimal acoustic performance For optimal acoustic performance when table-mounting the monitor, please ensure the screen is not tilted and the speaker enclosure is facing front, parallel with the table.
2. Setting up the display 3. Recover the hinge cover. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the display base, please follow the instructions below to avoid any possible damage or injury. 1. Place the display face down on a smooth surface. Pay attention not to scratch or damage the screen. Use a screwdriver to lift up the hinge cover. 4. Due to the display rear design, make sure to secure 4 spacer nuts (provided in the box) before installing the wall mount bracket.
2. Setting up the display 0° 90° -5° * Display design may differ from those illustrated. >35mm Tips on Placement • Warning Position the display where light does not shine directly on the screen. • Dim lighting conditions in the room for best Ambiglow effect. • For optimal acoustic performance when wall-mounting the monitor, please ensure the speaker enclosure is a minimum of 35mm from the wall.
2. Setting up the display 3 How to enable MultiView by OSD menu? 2.4 MultiView 1 What is it? Multiview enables active variety connect and view so that you can work with multiple devices like PC and Notebook side-by-side simultaneously, making complex multi-tasking work a breeze. 1. Toggle to the right to enter OSD Menu Screen. 2.
2. Setting up the display 4 MultiView in OSD menu [PBP]: Picture by Picture Open up a sub-window side-by-side of another signal source. A (main) B When the sub source is not detected: A (main) B Note The black strip shows on the top and the bottom of the screen for the correct aspect ratio when in the PBP mode. If you expect to see full screen side by side, adjust your devices resolution as pop up attention resolution, and make sure graphic card’s resolution is set to ‘1920 x 2160 at 60Hz’.
3. Ambiglow 2 How does it work? It is recommended that you dim the lighting conditions in your room for maximum effect. Ensure that Ambiglow is set to “on” mode. Start a movie, or play a game from your computer. The monitor will react with appropriate colors creating a halo effect, overall matching the image on the screen. You can also manually select Bright, Brighter, Brightest mode or ambiglow function off mode depending on your preference which helps reduce eye fatigue under prolonged usage. 3.
4. Image Optimization 2. Toggle to the up or down to select between the smartImage modes. 4. Image Optimization 3. The SmartImage on screen display will remain on screen for 5 seconds or you can also toggle to the right to make confirmation. There are multiple selections:Xbox, FPS, Racing, RTS, Gamer 1, Gamer 2, Movie, Economy, LowBlue Mode, SmartUniformity, Off. 4.
4. Image Optimization • Movie: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every details in darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the ultimate video display.
4. Image Optimization 4.2 SmartContrast 1 What is it? Unique technology that dynamically analyzes displayed content and automatically optimizes a display's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds. 2 Why do I need it? You want the very best visual clarity and viewing comfort for every type of content.
4. Image Optimization 4.3 HDR Settings in Windows 10 system Steps 1. Right click on the desktop, enter to display settings. 2. Select the display/monitor. STEP 5 3. Adjust resolution to 3840 x 2160. 4. Turn the “HDR and WCG” to on mode. 5. Adjust Brightness for SDR content. Note Windows 10 edition is required, always upgrade to the most updated version. Below linkage is for the further more information from mircrosoft official website. https://support.microsoft.
4. Image Optimization 4.4 Adaptive Sync Adaptive Sync PC gaming has long been an imperfect experience because GPUs and monitors update at different rates. Sometimes a GPU can render many new pictures during a single update of the monitor, and the monitor will show pieces of each picture as a single image. This is called “tearing.” Gamers can fix tearing with a feature called “v-sync,” but the image can become jerky as the GPU waits on the monitor to call for an update before delivering new pictures.
5. Sound by Bowers & Wilkins 5. Sound by Bowers & Wilkins The new Philips Momentum display boasts sound by legendary audio experts Bowers & Wilkins. Its speaker system, created exclusively for Philips by Bowers & Wilkins, delivers a thrilling performance with incredible dynamic range. Bass is rich and full while details are pristine, even at low volume. Take your sensory experience and immersion one level deeper by selecting audio modes to optimize your sound for both gaming and entertainment.
6.Power Delivery and Smart Power 6. Power Delivery and Smart Power Smart Power is an exclusive Philips technology that provides flexible power delivery options. With Smart Power, you can still charge your device without sacrificing the screen brightness, even set your screen as VESA DisplayHDR 1000. 1 How to enable Smart Power? 1. Connect the device to the USB C port. 2.
7. Technical Specifications 7. Technical Specifications Picture/Display Display Panel Type Backlight Panel Size Pixel Pitch Aspect Ratio Contrast ratio (typ.) Optimum Resolution Viewing Angle Picture Enhancement Display Colors Vertical Refresh Rate Horizontal Frequency sRGB Color Gamut SmartUniformity Delta E LowBlue Mode HDR Adaptive Sync Flicker-free Ambiglow Connectivity Connectors Power Delivery Sync input Convenience Speaker MultiView VA W-LED 55" (139.7 cm) 0.315 (H) mm x 0.
7. Technical Specifications OSD Languages Other Convenience Plug & Play Compatibility English, German, Spanish, Greek, French, Italian, Hungarian, Dutch, Portuguese, Brazil Portuguese, Polish, Russian, Swedish, Finnish, Turkish, Czech, Ukranian, Simplified Chinese, Traditional Chinese, Japanese, Korean VESA mount(200x200 mm), Kensington Lock DDC/CI, sRGB, Windows 10/8.
7. Technical Specifications Temperature range (Non-operation) Relative humidity (Non-operation) Atmospheric pressure (Non-operation) Environmental ROHS Packaging Specific Substances Cabinet Color Finish -20°C to 60°C 10% to 90% 500 to 1060hPa YES 100% recyclable 100% PVC BFR free housing Black Glossy and texture Note 1. This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet. 2.
7. Technical Specifications 3 Video Timing 7.1 Resolution & Preset Modes 1 Maximum Resolution 3840 x 2160 @ 144 Hz (HDMI/DP) 3840 x 2160 @ 120 Hz (USB C) 2 Recommended Resolution 3840 x 2160 @ 60 Hz H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.36 1024 x 768 60.00 60.02 1024 x 768 75.03 44.77 1280x 720 59.86 63.
7. Technical Specifications 3. If you feel the texts in your display is a little fade away, you can adjust your fonts setting in your PC/ Notebook as following steps.
8. Power Management 8. Power Management If you have VESA DPM compliance display card or software installed in your PC, the display can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the display will 'wake up' automatically.
9. Customer care and warranty Pixels and Sub pixels 9. Customer care and warranty A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors.
9. Customer care and warranty - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT display panel in a Philips flat panel display must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. Three adjacent lit sub pixels (one white pixel).
9.
9. Customer care and warranty 9.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For Warranty Period please refer to Warranty Statement in Regulation & Service Information Manual.
10. Troubleshooting & FAQs 10. Troubleshooting & FAQs 10.1 Troubleshooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. 1 Common Problems No Picture (Power LED not lit) • Make sure the power cord is plugged into the power outlet and into the back of the display.
10. Troubleshooting & FAQs • Adjust the image using the “Auto” function in OSD Main Controls. Green, red, blue, dark, and white dots appears on the screen • • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Image appears blurred, indistinct or too dark • Adjust the contrast and brightness on On-Screen Display. An "after-image", "burn-in" or "ghost image" remains after the power has been turned off.
10. Troubleshooting & FAQs Q3: 10.2 General FAQs When I install my display what should I do if the screen shows 'Cannot display this video mode'? Q1: Ans.: Recommended resolution for this display: 3840 x 2160. • Unplug all cables, then connect your PC to the display that you used previously. • In the Windows Start Menu, select Settings/Control Panel. In the Control Panel Window, select the display icon. Inside the display Control Panel, select the 'Settings' tab.
10. Troubleshooting & FAQs color setting, there are three settings as below. 1. Color Temperature: The 7 settings are Native, 5000K, 6500K, 7500K, 8200K, 9300K and 11500K. With settings in the 5000K range the panel appears "warm, with a redwhite color tone", while a 11500K temperature yields "cool, bluewhite toning". Ans.: Yes, the displays are Plug-andPlay compatible with Windows 10/8.1/8/7. Q10: Ans.
10. Troubleshooting & FAQs Ans.: Please press for 10 seconds to unlock/lock the hot key, by doing so, your display pops out “Attention” to show the unlock/ lock status as shown below illustrators. 10.3 Multiview FAQs Q1: Ans.: Normally the audio source is linked to the main picture source. If you want to change audiosource input , you can press to enter OSD menu. Select your preferred [Audio Source] option from the [Audio] main menu.
2021 © TOP Victory Investments Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
