Specifications
Table Of Contents
- Contents
- 1. Technical Specifications, Connections, and Chassis Overview
- 2. Safety Instructions, Warnings, and Notes
- 3. Directions for Use
- 4. Mechanical Instructions
- 4.1 Disassembly Procedures
- Figure 4-1 Exploded view 51” cabinet
- 4.1.1 Lower Center Back Cover Removal (86)
- 4.1.2 Side Back Cover Removal
- 4.1.3 Large Signal Board Removal (LSB)
- 4.1.4 AC Input Panel Removal
- 4.1.5 Small Signal Module Removal (SSM)
- 4.1.6 Side Jack Panel Removal
- 4.1.7 PIP Panel Removal (if present)
- 4.1.8 Small Signal Board Removal (SSB)
- 4.1.9 Convergence Panel Removal (ACS)
- 4.1.10 Wide Band Video Panel Removal (HOP)
- 4.1.11 Front Control Panel and Left or Right Speaker Removal (5)
- 4.1.12 Upper Back Cover Removal (4)
- 4.1.13 Plastic Light Barrier Removal (Optical Assembly)
- 4.1.14 Mirror Mounting Board Removal (57)
- 4.1.15 Complete Optical Assembly or Individual CRT Assembly Removal
- 4.2 Service Position
- 4.3 Picture Tube Replacement
- 4.4 Set Re-assembly
- 4.1 Disassembly Procedures
- 5. Service Modes, Error Codes, and Fault Finding
- 5.1 Test Conditions
- 5.2 Service Modes
- 5.3 Problems and Solving Tips (related to CSM)
- 5.4 ComPair
- 5.5 Error Codes
- 5.6 The ”Blinking LED” Procedure
- 5.7 Trouble Shooting Tips
- 6. Block Diagrams, Testpoint Overviews, and Waveforms
- 7. Circuit Diagrams and PWB Layouts
- Power Supply Panel: AC Input
- Layout Power Supply Panel (Top Side)
- Layout Power Supply Panel (Bottom Side)
- SSB: SIM Connector (Male)
- SSB: IF, I/O Videoprocessing
- SSB: Feature Box (100Hz Processing)
- SSB: HOP
- SSB: Audio Demodulator
- SSB: Painter
- Layout SSB (Top Side)
- Mapping Layout SSB (Top Side)
- Mapping Layout SSB (Bottom Side)
- Layout SSB (Bottom Side)
- SSM: Tuner
- SSM: I/O’s
- SSM: Video Buffer
- SSM: Convergence HV Output 1
- SSM: Convergence HV Output 2
- SSM: Interconnections
- SSM: Audio Amplifier
- SSM: Headphone Amplifier
- Mapping SSM C1-C8 Part 1
- Mapping SSM C1-C8 Part 2
- Mapping SSM C1-C8 Part 3
- Layout SSM (Top Side)
- Layout SSM (Bottom Side)
- CRT Panel: Red
- CRT Panel: Green
- CRT Panel: Blue
- Mapping CRT Panel: Red, Green, and Blue
- Layout CRT Panel (Top Side)
- Layout CRT Panel (Bottom Side)
- Large Signal Panel
- Large Signal Panel
- Large Signal Panel
- LSP: Diversity Tables
- Layout Large Signal Panel (Top Side)
- Layout Large Signal Panel (Bottom Side)
- Side Jack Panel
- Mapping Side Jack Panel G1
- Layout Side Jack Panel (Top Side)
- Layout Side Jack Panel (Bottom Side)
- ACS Module
- ACS Module
- ACS Module
- Mapping ACS Module H1-H3
- Layout ACS Panel (Top Side)
- Layout ACS Panel (Bottom Side)
- HOP Panel
- HOP Panel
- Diversity HOP Panel J1 and J2
- Mapping HOP Panel Part 1
- Mapping HOP Panel Part 2
- Layout HOP Panel (Top Side)
- Layout HOP Panel (Bottom Side)
- Keyboard Panel
- Mapping Keyboard Panel
- Layout Keyboard Panel (Top and BottomSide)
- UART Interface Module
- Layout UART Interface Modukle
- 8. Alignments
- 8.1 General Alignment Conditions
- 8.2 Hardware alignments
- 8.3 Software Alignments
- 8.4 Convergence and Geometry Adjustments
- 8.5 Option Settings
- 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets
- 9.1 Introduction
- 9.2 Power Supplies
- 9.3 Video
- Figure 9-7 Video signal block diagram
- 9.3.1 Side Jack Panel
- 9.3.2 SSM composite Inputs
- 9.3.3 SSM Video Switching
- 9.3.4 SSB Video Switching
- 9.3.5 SAW Filter Switching
- 9.3.6 3D Comb Filter
- 9.3.7 Sound Trap Switching
- 9.3.8 1fH Component Buffer Amplifiers
- 9.3.9 Feature Box
- 9.3.10 Eagle
- 9.3.11 ATSC module
- 9.3.12 SSM HOP Buffer Amplifiers
- 9.3.13 HOP RGB/YUV Switching
- 9.3.14 HOP Signal Processing
- 9.3.15 HOP Sharpness Control
- 9.3.16 HOP Tint Control
- 9.3.17 HOP RGB Amplifiers
- 9.3.18 HOP Analogue Control
- 9.3.19 CRT Panel
- 9.3.20 HOP Sync Switching and Processing
- 9.3.21 Line Output
- 9.3.22 Frame Amplifier
- 9.3.23 High Voltage Circuit
- 9.3.24 Shutdown
- 9.3.25 Convergence
- 9.4 Audio
- 9.5 Control/OSD
- 9.6 List of Abbreviations
- 9.7 IC Data Sheets
- 10. Spare Parts List
- 11. Revision List
Alignments
EN 80 DPTV585 AA8.
– WARM DRIVE BLUE: “-8”
15.Press the MENU button to return to the SAM menu. Exit the
Service mode by turning the set ”off”.
8.5 Option Settings
8.5.1 Introduction
The microprocessor communicates with a large number of I2C
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these specific
ICs (or functions) is made known by the option codes.
Notes:
• After changing the option(s), save them with the STORE
command.
• The new option setting is only active after the TV is
switched "off" and "on" again with the Mains switch (the
EAROM is then read again).
8.5.2 DEALER OPTIONS
Table 8-4 Dealer options
8.5.3 SERVICE OPTIONS
Table 8-5 Service options
8.5.4 Option Codes
Enter the Service Alignment Mode (SAM) by pressing the
following key sequence on the remote control transmitter:
0-6-2-5-9-6-[i+]. Do not allow the display to time out while
entering the key sequence.
Cursor to the OPT. NO. in the SERVICE OPTIONS level.
Locate the “option code label” on the inside right panel of the
unit and enter the correct codes for the model being serviced.
Example
• Group 1: 49483 32801 33055 32793
• Group 2: 39897 32768 32768 00000
Note: Remember to cursor to the STORE OPTIONS level and
select “OK” to save these changes
Menu
name Subjects
Option
s Physically in set
Personal
Options
Picture Mute Yes Picture mute active in
case no picture detected
No Noise in case of no picture
detected
Virgin Mode Yes TV starts up once with
language selection menu
after mains switch on for
the first time (virgin mode)
No TV does not starts up
once with language
selection menu after
mains switch on for the
first time (virgin mode)
Auto Store
Mode
None Autostore mode disabled
(not in installation menu)
PDC-
VPS
Autostore mode via ATS
(PDC/VPS) enabled
TXT
page
Autostore mode via ACI
enabled
PDC-
VPS-
TXT
Autostore mode via ACI or
ATS enabled
TXT
Preference
TOP Preference to TOP
Teletext
FLOF Preference to FLOF
Teletext
Menu
name Dual screen
TXT/EPG Dual
Screen Yes/No
Service
Options
Video repro Lightsensor Yes/No
2D Combfilter Yes/No
Pixel Plus Yes/No
Miscellaneous Tuner Type TEDE9/
UV1316
Opt. No. Group 1
Group 2