Specifications
Table Of Contents
- Contents
- 1. Technical Specifications, Connections, and Chassis Overview
- 2. Safety Instructions, Warnings, and Notes
- 3. Directions for Use
- 4. Mechanical Instructions
- 4.1 Disassembly Procedures
- Figure 4-1 Exploded view 51” cabinet
- 4.1.1 Lower Center Back Cover Removal (86)
- 4.1.2 Side Back Cover Removal
- 4.1.3 Large Signal Board Removal (LSB)
- 4.1.4 AC Input Panel Removal
- 4.1.5 Small Signal Module Removal (SSM)
- 4.1.6 Side Jack Panel Removal
- 4.1.7 PIP Panel Removal (if present)
- 4.1.8 Small Signal Board Removal (SSB)
- 4.1.9 Convergence Panel Removal (ACS)
- 4.1.10 Wide Band Video Panel Removal (HOP)
- 4.1.11 Front Control Panel and Left or Right Speaker Removal (5)
- 4.1.12 Upper Back Cover Removal (4)
- 4.1.13 Plastic Light Barrier Removal (Optical Assembly)
- 4.1.14 Mirror Mounting Board Removal (57)
- 4.1.15 Complete Optical Assembly or Individual CRT Assembly Removal
- 4.2 Service Position
- 4.3 Picture Tube Replacement
- 4.4 Set Re-assembly
- 4.1 Disassembly Procedures
- 5. Service Modes, Error Codes, and Fault Finding
- 5.1 Test Conditions
- 5.2 Service Modes
- 5.3 Problems and Solving Tips (related to CSM)
- 5.4 ComPair
- 5.5 Error Codes
- 5.6 The ”Blinking LED” Procedure
- 5.7 Trouble Shooting Tips
- 6. Block Diagrams, Testpoint Overviews, and Waveforms
- 7. Circuit Diagrams and PWB Layouts
- Power Supply Panel: AC Input
- Layout Power Supply Panel (Top Side)
- Layout Power Supply Panel (Bottom Side)
- SSB: SIM Connector (Male)
- SSB: IF, I/O Videoprocessing
- SSB: Feature Box (100Hz Processing)
- SSB: HOP
- SSB: Audio Demodulator
- SSB: Painter
- Layout SSB (Top Side)
- Mapping Layout SSB (Top Side)
- Mapping Layout SSB (Bottom Side)
- Layout SSB (Bottom Side)
- SSM: Tuner
- SSM: I/O’s
- SSM: Video Buffer
- SSM: Convergence HV Output 1
- SSM: Convergence HV Output 2
- SSM: Interconnections
- SSM: Audio Amplifier
- SSM: Headphone Amplifier
- Mapping SSM C1-C8 Part 1
- Mapping SSM C1-C8 Part 2
- Mapping SSM C1-C8 Part 3
- Layout SSM (Top Side)
- Layout SSM (Bottom Side)
- CRT Panel: Red
- CRT Panel: Green
- CRT Panel: Blue
- Mapping CRT Panel: Red, Green, and Blue
- Layout CRT Panel (Top Side)
- Layout CRT Panel (Bottom Side)
- Large Signal Panel
- Large Signal Panel
- Large Signal Panel
- LSP: Diversity Tables
- Layout Large Signal Panel (Top Side)
- Layout Large Signal Panel (Bottom Side)
- Side Jack Panel
- Mapping Side Jack Panel G1
- Layout Side Jack Panel (Top Side)
- Layout Side Jack Panel (Bottom Side)
- ACS Module
- ACS Module
- ACS Module
- Mapping ACS Module H1-H3
- Layout ACS Panel (Top Side)
- Layout ACS Panel (Bottom Side)
- HOP Panel
- HOP Panel
- Diversity HOP Panel J1 and J2
- Mapping HOP Panel Part 1
- Mapping HOP Panel Part 2
- Layout HOP Panel (Top Side)
- Layout HOP Panel (Bottom Side)
- Keyboard Panel
- Mapping Keyboard Panel
- Layout Keyboard Panel (Top and BottomSide)
- UART Interface Module
- Layout UART Interface Modukle
- 8. Alignments
- 8.1 General Alignment Conditions
- 8.2 Hardware alignments
- 8.3 Software Alignments
- 8.4 Convergence and Geometry Adjustments
- 8.5 Option Settings
- 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets
- 9.1 Introduction
- 9.2 Power Supplies
- 9.3 Video
- Figure 9-7 Video signal block diagram
- 9.3.1 Side Jack Panel
- 9.3.2 SSM composite Inputs
- 9.3.3 SSM Video Switching
- 9.3.4 SSB Video Switching
- 9.3.5 SAW Filter Switching
- 9.3.6 3D Comb Filter
- 9.3.7 Sound Trap Switching
- 9.3.8 1fH Component Buffer Amplifiers
- 9.3.9 Feature Box
- 9.3.10 Eagle
- 9.3.11 ATSC module
- 9.3.12 SSM HOP Buffer Amplifiers
- 9.3.13 HOP RGB/YUV Switching
- 9.3.14 HOP Signal Processing
- 9.3.15 HOP Sharpness Control
- 9.3.16 HOP Tint Control
- 9.3.17 HOP RGB Amplifiers
- 9.3.18 HOP Analogue Control
- 9.3.19 CRT Panel
- 9.3.20 HOP Sync Switching and Processing
- 9.3.21 Line Output
- 9.3.22 Frame Amplifier
- 9.3.23 High Voltage Circuit
- 9.3.24 Shutdown
- 9.3.25 Convergence
- 9.4 Audio
- 9.5 Control/OSD
- 9.6 List of Abbreviations
- 9.7 IC Data Sheets
- 10. Spare Parts List
- 11. Revision List
