Specifications
Table Of Contents
- Contents
- 1. Technical Specifications, Connections, and Chassis Overview
- 2. Safety Instructions, Warnings, and Notes
- 3. Directions for Use
- 4. Mechanical Instructions
- 4.1 Disassembly Procedures
- Figure 4-1 Exploded view 51” cabinet
- 4.1.1 Lower Center Back Cover Removal (86)
- 4.1.2 Side Back Cover Removal
- 4.1.3 Large Signal Board Removal (LSB)
- 4.1.4 AC Input Panel Removal
- 4.1.5 Small Signal Module Removal (SSM)
- 4.1.6 Side Jack Panel Removal
- 4.1.7 PIP Panel Removal (if present)
- 4.1.8 Small Signal Board Removal (SSB)
- 4.1.9 Convergence Panel Removal (ACS)
- 4.1.10 Wide Band Video Panel Removal (HOP)
- 4.1.11 Front Control Panel and Left or Right Speaker Removal (5)
- 4.1.12 Upper Back Cover Removal (4)
- 4.1.13 Plastic Light Barrier Removal (Optical Assembly)
- 4.1.14 Mirror Mounting Board Removal (57)
- 4.1.15 Complete Optical Assembly or Individual CRT Assembly Removal
- 4.2 Service Position
- 4.3 Picture Tube Replacement
- 4.4 Set Re-assembly
- 4.1 Disassembly Procedures
- 5. Service Modes, Error Codes, and Fault Finding
- 5.1 Test Conditions
- 5.2 Service Modes
- 5.3 Problems and Solving Tips (related to CSM)
- 5.4 ComPair
- 5.5 Error Codes
- 5.6 The ”Blinking LED” Procedure
- 5.7 Trouble Shooting Tips
- 6. Block Diagrams, Testpoint Overviews, and Waveforms
- 7. Circuit Diagrams and PWB Layouts
- Power Supply Panel: AC Input
- Layout Power Supply Panel (Top Side)
- Layout Power Supply Panel (Bottom Side)
- SSB: SIM Connector (Male)
- SSB: IF, I/O Videoprocessing
- SSB: Feature Box (100Hz Processing)
- SSB: HOP
- SSB: Audio Demodulator
- SSB: Painter
- Layout SSB (Top Side)
- Mapping Layout SSB (Top Side)
- Mapping Layout SSB (Bottom Side)
- Layout SSB (Bottom Side)
- SSM: Tuner
- SSM: I/O’s
- SSM: Video Buffer
- SSM: Convergence HV Output 1
- SSM: Convergence HV Output 2
- SSM: Interconnections
- SSM: Audio Amplifier
- SSM: Headphone Amplifier
- Mapping SSM C1-C8 Part 1
- Mapping SSM C1-C8 Part 2
- Mapping SSM C1-C8 Part 3
- Layout SSM (Top Side)
- Layout SSM (Bottom Side)
- CRT Panel: Red
- CRT Panel: Green
- CRT Panel: Blue
- Mapping CRT Panel: Red, Green, and Blue
- Layout CRT Panel (Top Side)
- Layout CRT Panel (Bottom Side)
- Large Signal Panel
- Large Signal Panel
- Large Signal Panel
- LSP: Diversity Tables
- Layout Large Signal Panel (Top Side)
- Layout Large Signal Panel (Bottom Side)
- Side Jack Panel
- Mapping Side Jack Panel G1
- Layout Side Jack Panel (Top Side)
- Layout Side Jack Panel (Bottom Side)
- ACS Module
- ACS Module
- ACS Module
- Mapping ACS Module H1-H3
- Layout ACS Panel (Top Side)
- Layout ACS Panel (Bottom Side)
- HOP Panel
- HOP Panel
- Diversity HOP Panel J1 and J2
- Mapping HOP Panel Part 1
- Mapping HOP Panel Part 2
- Layout HOP Panel (Top Side)
- Layout HOP Panel (Bottom Side)
- Keyboard Panel
- Mapping Keyboard Panel
- Layout Keyboard Panel (Top and BottomSide)
- UART Interface Module
- Layout UART Interface Modukle
- 8. Alignments
- 8.1 General Alignment Conditions
- 8.2 Hardware alignments
- 8.3 Software Alignments
- 8.4 Convergence and Geometry Adjustments
- 8.5 Option Settings
- 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets
- 9.1 Introduction
- 9.2 Power Supplies
- 9.3 Video
- Figure 9-7 Video signal block diagram
- 9.3.1 Side Jack Panel
- 9.3.2 SSM composite Inputs
- 9.3.3 SSM Video Switching
- 9.3.4 SSB Video Switching
- 9.3.5 SAW Filter Switching
- 9.3.6 3D Comb Filter
- 9.3.7 Sound Trap Switching
- 9.3.8 1fH Component Buffer Amplifiers
- 9.3.9 Feature Box
- 9.3.10 Eagle
- 9.3.11 ATSC module
- 9.3.12 SSM HOP Buffer Amplifiers
- 9.3.13 HOP RGB/YUV Switching
- 9.3.14 HOP Signal Processing
- 9.3.15 HOP Sharpness Control
- 9.3.16 HOP Tint Control
- 9.3.17 HOP RGB Amplifiers
- 9.3.18 HOP Analogue Control
- 9.3.19 CRT Panel
- 9.3.20 HOP Sync Switching and Processing
- 9.3.21 Line Output
- 9.3.22 Frame Amplifier
- 9.3.23 High Voltage Circuit
- 9.3.24 Shutdown
- 9.3.25 Convergence
- 9.4 Audio
- 9.5 Control/OSD
- 9.6 List of Abbreviations
- 9.7 IC Data Sheets
- 10. Spare Parts List
- 11. Revision List
Mechanical Instructions
EN 6 DPTV585 AA4.
4. Mechanical Instructions
Index of this chapter:
4.1 Disassembly Procedures
4.2 Service Position
4.3 Picture Tube Replacement
4.4 Set Re-assembly
Notes:
• Figures below can deviate slightly from the actual situation,
due to the different set executions.
• Follow the disassembly instructions in described order.
4.1 Disassembly Procedures
All numbers, found in the following text, refer to the drawing
below and apply to both the 43” and 55” models.
Note:
• Not all shown items are available for all models.
• If you are servicing a PWB or speaker, you do not need to
remove the plastic Upper Back Cover (4).
Figure 4-1 Exploded view 51” cabinet
4.1.1 Lower Center Back Cover Removal (86)
1. Remove all screws (B and C).
2. Remove the Lower Center Back Cover.
4.1.2 Side Back Cover Removal
Remove all screws (F) from each of the Side Back Covers
(some prying may be necessary to dislodge covers).
Note: This allows access to the Side Jack Panel and to the Left
and the Right Speakers.
4.1.3 Large Signal Board Removal (LSB)
Note: See for the location of the panels figure "PWB location"
in Chapter 1 "Technical Specifications, Connection Facilities,
and Chassis Overview".
1. Disconnect all cables.
2. Remove three screws from the center of the PWB and pull
three tabs on the right of the bracket.
3. Lift the right side of the LSB and slide the panel up and out.
4.1.4 AC Input Panel Removal
1. Disconnect all cables.
2. Remove four screws from the PWB.
3. Lift the AC Input Panel up and out.
4.1.5 Small Signal Module Removal (SSM)
1. Remove three screws along the rear of the chassis frame.
2. Remove two screws, which hold the chassis frame and are
located between the LSB and SSB panels.
3. Remove one screw, which holds the chassis frame and is
located between the Input Power and LSB panels
4. Remove the rear Jack Panel cover (76).
5. Slide the Chassis assembly rearward to allow access to the
Module Bracket.
6. Remove the screws, which secure the Module Bracket,
and release the cables.
7. Remove two screws from the centre of the SSM PWB.
8. Pull three tabs on the right of the panel bracket.
9. Lift the right side of the SSM, then move the SSM to the
right to remove it.
F_15120_044.eps
120805