Specifications
Table Of Contents
- Contents
- 1. Technical Specifications, Connections, and Chassis Overview
- 2. Safety Instructions, Warnings, and Notes
- 3. Directions for Use
- 4. Mechanical Instructions
- 4.1 Disassembly Procedures
- Figure 4-1 Exploded view 51” cabinet
- 4.1.1 Lower Center Back Cover Removal (86)
- 4.1.2 Side Back Cover Removal
- 4.1.3 Large Signal Board Removal (LSB)
- 4.1.4 AC Input Panel Removal
- 4.1.5 Small Signal Module Removal (SSM)
- 4.1.6 Side Jack Panel Removal
- 4.1.7 PIP Panel Removal (if present)
- 4.1.8 Small Signal Board Removal (SSB)
- 4.1.9 Convergence Panel Removal (ACS)
- 4.1.10 Wide Band Video Panel Removal (HOP)
- 4.1.11 Front Control Panel and Left or Right Speaker Removal (5)
- 4.1.12 Upper Back Cover Removal (4)
- 4.1.13 Plastic Light Barrier Removal (Optical Assembly)
- 4.1.14 Mirror Mounting Board Removal (57)
- 4.1.15 Complete Optical Assembly or Individual CRT Assembly Removal
- 4.2 Service Position
- 4.3 Picture Tube Replacement
- 4.4 Set Re-assembly
- 4.1 Disassembly Procedures
- 5. Service Modes, Error Codes, and Fault Finding
- 5.1 Test Conditions
- 5.2 Service Modes
- 5.3 Problems and Solving Tips (related to CSM)
- 5.4 ComPair
- 5.5 Error Codes
- 5.6 The ”Blinking LED” Procedure
- 5.7 Trouble Shooting Tips
- 6. Block Diagrams, Testpoint Overviews, and Waveforms
- 7. Circuit Diagrams and PWB Layouts
- Power Supply Panel: AC Input
- Layout Power Supply Panel (Top Side)
- Layout Power Supply Panel (Bottom Side)
- SSB: SIM Connector (Male)
- SSB: IF, I/O Videoprocessing
- SSB: Feature Box (100Hz Processing)
- SSB: HOP
- SSB: Audio Demodulator
- SSB: Painter
- Layout SSB (Top Side)
- Mapping Layout SSB (Top Side)
- Mapping Layout SSB (Bottom Side)
- Layout SSB (Bottom Side)
- SSM: Tuner
- SSM: I/O’s
- SSM: Video Buffer
- SSM: Convergence HV Output 1
- SSM: Convergence HV Output 2
- SSM: Interconnections
- SSM: Audio Amplifier
- SSM: Headphone Amplifier
- Mapping SSM C1-C8 Part 1
- Mapping SSM C1-C8 Part 2
- Mapping SSM C1-C8 Part 3
- Layout SSM (Top Side)
- Layout SSM (Bottom Side)
- CRT Panel: Red
- CRT Panel: Green
- CRT Panel: Blue
- Mapping CRT Panel: Red, Green, and Blue
- Layout CRT Panel (Top Side)
- Layout CRT Panel (Bottom Side)
- Large Signal Panel
- Large Signal Panel
- Large Signal Panel
- LSP: Diversity Tables
- Layout Large Signal Panel (Top Side)
- Layout Large Signal Panel (Bottom Side)
- Side Jack Panel
- Mapping Side Jack Panel G1
- Layout Side Jack Panel (Top Side)
- Layout Side Jack Panel (Bottom Side)
- ACS Module
- ACS Module
- ACS Module
- Mapping ACS Module H1-H3
- Layout ACS Panel (Top Side)
- Layout ACS Panel (Bottom Side)
- HOP Panel
- HOP Panel
- Diversity HOP Panel J1 and J2
- Mapping HOP Panel Part 1
- Mapping HOP Panel Part 2
- Layout HOP Panel (Top Side)
- Layout HOP Panel (Bottom Side)
- Keyboard Panel
- Mapping Keyboard Panel
- Layout Keyboard Panel (Top and BottomSide)
- UART Interface Module
- Layout UART Interface Modukle
- 8. Alignments
- 8.1 General Alignment Conditions
- 8.2 Hardware alignments
- 8.3 Software Alignments
- 8.4 Convergence and Geometry Adjustments
- 8.5 Option Settings
- 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets
- 9.1 Introduction
- 9.2 Power Supplies
- 9.3 Video
- Figure 9-7 Video signal block diagram
- 9.3.1 Side Jack Panel
- 9.3.2 SSM composite Inputs
- 9.3.3 SSM Video Switching
- 9.3.4 SSB Video Switching
- 9.3.5 SAW Filter Switching
- 9.3.6 3D Comb Filter
- 9.3.7 Sound Trap Switching
- 9.3.8 1fH Component Buffer Amplifiers
- 9.3.9 Feature Box
- 9.3.10 Eagle
- 9.3.11 ATSC module
- 9.3.12 SSM HOP Buffer Amplifiers
- 9.3.13 HOP RGB/YUV Switching
- 9.3.14 HOP Signal Processing
- 9.3.15 HOP Sharpness Control
- 9.3.16 HOP Tint Control
- 9.3.17 HOP RGB Amplifiers
- 9.3.18 HOP Analogue Control
- 9.3.19 CRT Panel
- 9.3.20 HOP Sync Switching and Processing
- 9.3.21 Line Output
- 9.3.22 Frame Amplifier
- 9.3.23 High Voltage Circuit
- 9.3.24 Shutdown
- 9.3.25 Convergence
- 9.4 Audio
- 9.5 Control/OSD
- 9.6 List of Abbreviations
- 9.7 IC Data Sheets
- 10. Spare Parts List
- 11. Revision List
Directions for Use
EN 5DPTV585 AA 3.
• Where necessary, measure the waveforms and voltages
with (D) and without (E) aerial signal. Measure the
voltages in the power supply section both in normal
operation (G) and in standby (F). These values are
indicated by means of the appropriate symbols.
• The picture tube panel has printed spark gaps. Each spark
gap is connected between an electrode of the picture tube
and the Aquadag coating.
• The semiconductors indicated in the circuit diagram and in
the parts lists, are interchangeable per position with the
semiconductors in the unit, irrespective of the type
indication on these semiconductors.
• Manufactured under license from Dolby Laboratories.
‘Dolby’, ‘Pro Logic’ and the ‘double-D symbol’, are
trademarks of Dolby Laboratories.
Figure 2-2 Dolby PL symbol
3. Directions for Use
You can download this information from the following websites:
http://www.philips.com/support
http://www.p4c.philips.com
E_06532_006.eps
240604