2661.1 eng 03-07-2007 11:57 Pagina 1 1 1.1 1.2 1.3 Important 3 Safety 3 Care of the screen 3 Recycling 3 2 2.1 2.2 Your TV 4 Television overview 4 Product highlights 5 3 3.1 3.2 3.3 3.4 3.5 3.6 Getting started 5 Position the TV 5 Wall mounting - VESA 5 Remote control batteries 7 Antenna cable 7 Connect the mains 7 First time installation 7 4 4.1 4.2 4.3 4.4 4.5 4.6 4.
661.1 eng 03-07-2007 11:57 2007 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
1 03-07-2007 11:57 Pagina 3 Important Read this user manual before you start to use this product. Pay attention to this section and closely follow the instructions. The warranty does not apply to damage caused by not taking into account the instructions. • Stationary images Avoid stationary images as much as possible. If you can not, reduce screen contrast and brightness to prevent damage to the screen. Stationary images are images that remain on the screen for a long time.
2661.1 eng 2 03-07-2007 11:57 Pagina 4 Your TV This section gives you an overview of the controls and functions of this TV. 2.
2.2 03-07-2007 11:57 Pagina 5 Product highlights Your new TV is equipped with some of the most modern audio or video innovations. Your TV offers the following advantages ... Full High Definition LCD display A full HD resolution of 1920x1080p, the highest resolution of HD sources. It offers a brilliant flickerfree progressive scan picture with optimum brightness and superb colours. 3 Getting started ENGLISH 2661.
2661.1 eng 3.2 03-07-2007 11:57 Pagina 6 Wall mounting - VESA Ò To remove the TV stand locate the 4 screws of the TV stand. Your TV is prepared for VESA compliant wall mounting. This bracket is not included. Use a VESA compliant bracket with code VESA MIS-F, 600, 400 M8. ç Warning Consider the TV’s weight if you wall mount it. Improper mounting could result in severe injury or damage. Koninklijke Philips Electronics N.V.
3.3 03-07-2007 11:57 Pagina 7 Remote control batteries 3.5 Connect the mains cord ‡ Verify that your mains voltage corresponds with the voltage printed on the sticker at the back of the TV. Do not insert the mains cord if the voltage is different. ® Insert the mains cord tightly. ‡ Open the battery cover on the back of the remote control. ® Insert the 2 batteries supplied (Type AA-R61,5V). Make sure the + and - ends of the batteries line up correctly (inside of case is marked.) Ò Close the cover.
2661.1 eng 4 03-07-2007 11:57 Pagina 8 Use your TV Learn how to operate your TV for daily use. 4.1 Switch on or off - Standby To switch on the TV: • Press B Power at the right side of the TV if the standby led is off. • Press B on the remote control if the standby led in on. To switch to standby: • Press B on the remote control. B POWER - PRO To switch on from standby without remote control: • Press B Power at the side of the TV to switch off first and press B Power again to switch on.
4.2 03-07-2007 11:57 Pagina 9 Watch TV 4.3 4.2.1 Switch channels ‡ To switch TV channels: • Press a number (1 to 999) or press P+ or Pon your remote control. • Press Program/Channel - or + on the side controls of the TV. ® Press R to return to the previously viewed TV channel . Watch channels from a digital receiver ENGLISH 2661.1 eng ‡ Switch on the digital receiver. The picture from your receiver might appear automatically on your screen.
2661.1 eng 4.5 03-07-2007 11:57 Pagina 10 Watch a DVD 4.6 ‡ Insert a DVD disc in your player. ® Press Play π. The picture from your player appears automatically on your screen. Select a Teletext page Most TV channels broadcast information via Teletext. To watch Teletext: ‡ Press b. The main index page appears. If the picture does not appear: ‡ Press v on the remote control.
2661.1 eng 11:57 Pagina 11 Change Ambilight mode ENGLISH 4.7 03-07-2007 You can choose among four Ambilight modes: • Colour Sets Ambilight to a constant colour. • Relaxed Sets Ambilight to change soft and smoothly with the images on screen. • Moderate Sets Ambilight between Relaxed and Dynamic. • Dynamic Sets Ambilight to change quick and responsive. To change the Ambilight mode: ‡ Press Ambilight to switch on or off.
2661.1 eng 5 03-07-2007 11:57 Pagina 12 Use more of your TV This section deals with the more advanced use of your TV: • how to use the menus • to adjust the picture, sound and Ambilight settings • more about Teletext • how to create favourite channel lists • • • • the advantages of Electronic Programme Guide how to set locks and timers to set subtitles and select a subtitle language how you can view your photos or play your favourite music from a memory card or USB memory device.
03-07-2007 11:57 Pagina 13 17 Subtitles j To activate or deactivate the subtitle mode. 18 ‡ MHEG cancel No function. 19 Ambilight To switch Ambilight on or off. 20 On screen information i To show channel or programme information if available. 21 Volume up or down V To adjust the volume. 22 Menu To switch the menu on or off. 23 Option To switch the Quick access menu on or off. 24 Demo To switch the Demo menu on and to get a demonstration of the features of the TV. 5.1.
2661.1 eng 03-07-2007 11:57 Pagina 14 5.1.4 Set to operate a particular STB You may need to switch the factory setting for STB on the remote control to fit your particular Digital or Satellite receiver. ‡ Press the STB key and the appropriate number key at the same time. • STB and number key 1 (factory setting) • STB and 2 All Philips device control keys will blink for 1 second to confirm the setting. 5.1.
03-07-2007 11:57 Pagina 15 5.2.2 Use of the menu Learn to use the menus with this example. ‡ Press Menu on the remote control. a OK LIST b MENU MENU º Press navigation key right to enter the picture settings. Picture ENGLISH 2661.1 eng Contrast Contrast Brightness 90 47 Colour Hue 52 0 Sharpness 4 BROWSE Tint BROWSE V ¬ P Perfect Pixel HD HD Natural Motion The main menu appears on the screen. ◊Press navigation key down to select Brightness.
2661.1 eng 03-07-2007 11:57 Pagina 16 5.2.3 Quick access menu The Quick access menu gives direct access to some often needed menu items. When digital channels are installed and broadcasted the relevant digital options are shown in the menu. 5.3 ‡ Press Option on the remote control. ® Press navigation key up or down to select an option. Ò Press OK to show the selected option menu. † Press navigation key up, down, left, right to adjust the settings in the menu. º Press Option to quit the menu. 5.3.
03-07-2007 11:57 Pagina 17 5.3.3 Picture settings This section describes how to adjust all picture settings. ‡ Press Menu on the remote control and select TV menu > TV settings > Picture and press navigation key right to enter the list. ® Press navigation key up or down to select a setting.
2661.1 eng 03-07-2007 11:57 Pagina 18 Unscaled (Only for HD and PC.) Maximum sharpness. Distortion may appear on borders. Black bars may appear with pictures from your PC. 5.3.4 Widescreen picture format Avoid black bars on the sides or on top and bottom of the picture. Change the picture format to a format that fills the screen. ‡ Press q to switch on the Picture format menu. Ambilight MODE MHEG CANCEL q ® Press navigation key up or down to select an available picture format.
03-07-2007 11:57 Pagina 19 • Audio language A list of audio languages for the current programme may be available when digital channels are installed and broadcasted. See also section 5.2.3 Quick access menu. To permanently change the audio language, see section 6 Channel installation. • Dual I/II If broadcasted, you can choose between two different languages. • Mono/stereo If stereo broadcasting is available, you can select Mono or Stereo per TV channel.
2661.1 eng 03-07-2007 11:57 Pagina 20 ç Caution To avoid bad infrared remote control reception, place your devices out of sight of Ambilight. TV standby with Ambilight When the TV is in standby, you can switch Ambilight on. In this case Ambilight is only available as constant colour. ‡ Press Ambilight on the remote control when the TV is in standby. ® Press Mode repeatedly to select an available colour. Ambilight Ambilight MODE MHEG CANCEL MODE 5.
03-07-2007 11:57 Pagina 21 5.5.4 Search teletext Quickly jump to a subject linked to a series of pagenumbers or search for specific words in teletext pages. ‡ Press b. ® Press OK to highlight the first word or number. Ò Press navigation key left, right or up, down to jump to the next word or number on the page. † Press OK to search a page which holds the highlighted word or number. º Press navigation key up until no word or number is highlighted to quit Search. 5.5.
2661.1 eng 5.6 03-07-2007 11:57 Pagina 22 Create favourite channel lists View the All channels list or set up a Favourite list of your own with your preferred TV channels and radio stations. For example, each member of your family can create his or her own favourite list. 5.6.1 Select a favourite list Learn how to select one of the favourite channel lists. ‡ Press OK. The first time after you have finished the installation, the All channels list is shown.
5.7 03-07-2007 11:57 Pagina 23 Electronic Programme Guide - EPG - The Electronic Programme guide is an on screen guide to scheduled digital TV programmes. You can navigate, select and view programmes by time, title or genre. There are two types of EPG, ‘Now and Next’ and ‘7 or 8 day’ EPG. When digital channels are installed and broadcasted, EPG is available. ‘Now and Next’ is always available but the ‘7 or 8 day’ EPG is only available in some countries.
2661.1 eng 5.8 03-07-2007 11:57 Pagina 24 Timers and locks This section describes how to switch the TV on or off at a specified time and to lock or unlock the TV. 5.8.1 Automatically switch to standby Sleeptimer switches the TV to standby after a time. ‡ Press Menu on the remote control and select TV menu > Features > Sleeptimer and press navigation key right to enter the sleeptimer bar. ® Press navigation key up or down to set the time up to 180 minutes in steps of 5 minutes.
03-07-2007 11:57 Pagina 25 Lock one or more channels and connected devices ‡ Select Custom lock. ® Press navigation key right to enter. Ò Press navigation key up or down to select Channel lock. † Press navigation key right. º Press navigation key up or down to select the channel(s) you want to lock or unlock. ◊Each time press OK to lock or unlock the channel. 5.9.
61.1 eng 03-07-2007 11:57 Pagina 26 5.10 View and play: photos, MP3, ... Watch pictures or listen to music stored on a memory card or USB device (not supplied with the TV). Watch your pictures as a slideshow or listen to a self made music playlist. rNote Philips can not be held responsible if your memory card or USB device is not supported nor shall Philips accept any liability for damage or loss of stored data. • Do not subject the card to excessive pressure or strong impacts.
Pagina 27 Afrika_2001 Kenya.jpg Congo.jpg Victoria.jpg Dakar.jpg Kenya.jpg Cairo.jpg † Press OK to view the picture or to start a slideshow of the pictures in the album. º Press OK to pause the slideshow. Press again to restart. ◊Press one of the colour keys on the remote control to perform the corresponding function shown at the bottom of the screen. Press the blue key to stop the show and to see more functions. If the function bar at the bottom disappeared, press any colour key to let it reappear.
2661.1 eng 03-07-2007 11:57 Pagina 28 5.11 Listen to radio channels 5.12 Software update If digital broadcasting is available, digital radio channels will be installed during installation. To listen to a digital radio channel: ‡ Press OK on the remote control. The All channels menu is displayed. ® Use the number keys to select a radio channel available from channel number 400 onwards. To reorder see section 6.3.3 Reorder the channels. Ò Press OK. Philips continuously tries to improve its products.
03-07-2007 11:57 Pagina 29 5.12.2 Software download from the PC to the USB device ‡ Insert the USB memory device into a PC linked to the internet. ® Locate and open the file “update.htm” on your USB device. Ò Read the instructions on screen and click on the Send ID button. The software update is downloaded on the USB memory device. † Remove the USB memory device from your PC. Ò The update process starts automatically. Please wait.
2661.1 eng 03-07-2007 11:57 Pagina 30 ◊The TV switches off.The screen stays black for about 10 seconds. Please, wait. ‹The TV switches back on again.The update is done. 5.12.4 Verify the current software version Updating software is only possible if the version of the new available software is different from the current one.You can verify your current software version. ‡ Select Software update in the TV menu. ® Press navigation key right.
6 03-07-2007 11:57 Pagina 31 Channel installation The first time you switched on your TV you’ve selected the language of the TV menus and all the available channels have been installed. This chapter will help you if you find it necessary to re-do the initial installation or if you want to tune in a new analogue TV channel. rNotes: - You do not have to follow every step described if it is not necessary.
2661.1 eng 03-07-2007 11:57 Pagina 32 6.2 Analogue: Manual installation You can tune-in analogue TV channels channel by channel manually with Manual installation. 6.2.1 Select the system ‡ Press Menu on the remote control and select TV menu > Installation > Channel installation > Analogue: Manual installation. ® Press navigation key right to enter the Manual installation menu. System is highlighted. Ò Press navigation key right to enter the System list.
03-07-2007 11:57 Pagina 33 6.3.2 Uninstall or reinstall a channel To uninstall a stored channel so that it is no longer possible to tune to. Reinstall an earlier uninstalled channel. ‡ Press Menu on the remote control and select TV menu > Installation > Channel installation > Rearrange. ® Press navigation key right to enter the channel list. Ò Press navigation key up or down in the channel list to select the channel you want to uninstall or reinstall.
2661.1 eng 03-07-2007 11:57 Pagina 34 7 Connections 7.1 Connection overview 3 2 1 11 S-VIDEO Y 12 13 Pb Pr L 16 R 14 EXT 2 EXT 1 4 5 L R COMMON INTERFACE AUDIO OUT DISPLAY SYNCHRONIZED 6 7 8 9 HDMI 1 HDMI 2 10 OUT IN DIGITAL AUDIO SERVICE UART ANTENNA DISPLAY SYNCHRONIZED. Back connectors 1 EXT1 Scart connector for DVD,VCR, digital receiver, game console, etc. 2 EXT2 Second scart connector.
7.2 03-07-2007 11:57 Pagina 35 About connecting Learn here how to make the best connection for your device. Six connections are ready to use at the back of the TV - EXT1, EXT2, EXT3, HDMI1 and HDMI2. Connect your device with the highest possible quality connection. Look for the highest quality connection on your device. Use that connection to your TV. 7.2.2 YPbPr - Higher quality ★★★★ Use the Component Video YPbPr connections together with the Audio L/R mini jack.
2661.1 eng 03-07-2007 11:57 Pagina 36 7.2.4 S-Video - Good quality ★★ Use a S-Video cable together with an Audio L/R (cinch) cable. Match the cable colours when you connect. An S-Video cable Audio L/R cable - Red, White 7.2.5 Video - Basic quality ★ Use a Video (cinch) cable together with an Audio L/R (cinch) cable. Match the cable colours when you connect Combined Video - yellow and Audio L/R cable - red and white 7.2.
7.3 03-07-2007 11:57 Pagina 37 Connect your devices ENGLISH 2661.1 eng The connections shown in this section are recommendations for the most used cases. Other solutions may be possible. 7.3.1 DVD player Use a scart cable to connect the device to the EXT1 input at the back of the TV. Y Pb Pr AUDIO L/ R EXT 3 L EXT 1 OUT R AUDIO OUT EXT 2 IN DIGITAL AUDIO HDMI 1 HDMI 2 ANTENNA DVD Player 7.3.2 DVD Recorder or Digital Receiver Use a scart cable and 2 antenna cables.
2661.1 eng 03-07-2007 11:57 Pagina 38 7.3.4 DVD Recorder and Home Theatre System Use a scart cable, 2 antenna cables and 1 digital audio (cinch) cable. Y Pb Pr AUDIO L/ R DIGITAL AUDIO OUT L R AUDIO OUT EXT 3 EXT 2 EXT 1 OUT IN DIGITAL AUDIO HDMI 1 HDMI 2 ANTENNA OUT DIGITAL AUDIO IN IN DVD Recorder Home Theatre System 7.3.5 DVD Recorder and DVD Home Theatre System Use 2 scart cables, 2 antenna cables and 1 digital audio (cinch) cable.
2661.1 eng 03-07-2007 11:57 Pagina 39 HD Digital receiver / HD satellite receiver Use a HDMI cable and 2 antenna cables. ENGLISH 7.3.7 Y Pb Pr AUDIO L/ R EXT 3 L EXT 1 HDMI OUT OUT IN OUT R AUDIO OUT EXT 2 IN DIGITAL AUDIO HDMI 1 HDMI 2 ANTENNA HD Digital receiver / HD Satellite receiver 7.3.8 DVD-R, Home Theatre System and Digital receiver Use 3 scart cables, 3 antenna cables and 1 audio (cinch) cable.
2661.1 eng 03-07-2007 11:57 Pagina 40 7.3.10 Game console The most practical connection for a game console is at the side of the TV. More qualitative connections are at the back of the TV. Connected at the side of the TV Use the Video and Audio L/R (cinch) connectors. S-VIDEO VIDEO L AUDIO R 7.3.12 Personal Computer The best connection for a PC is at the back of the TV. A more practical connection, but only for viewing photos and films from your PC, is the connection at the side of the TV.
7.4 03-07-2007 11:57 Pagina 41 Connections setup When all devices have been connected the TV needs to know what connections you have made, which device is connected to which connector. 7.4.1 Digital Audio In (if present) If you use the Digital Audio In connection, assign this connection, in the menu, to the device from where the sound comes from. ‡ Press Menu on the remote control and select TV menu > Installation > Connections > Digital Audio In. ® Press navigation key right to enter the list.
2661.1 eng 7.5 03-07-2007 11:57 Pagina 42 Preparing for digital services Scrambled digital TV channels can be decoded with a Conditional Access Module (CAM) and a Smart card provided by a digital TV service operator. The CAM may enable several services depending on the operator you choose (e.g. Pay TV). Contact your digital TV service operator for more information and terms. 7.5.1 Insert a Conditional Access Module CAM ) Warning Switch off your TV before inserting a CAM.
2661.
2661.1 eng 9 03-07-2007 11:57 Pagina 44 Troubleshooting Television and remote control The TV does not switch on • Verify the mains cord connection. • Verify if the batteries of the remote control are flat or weak. Verify their + / - orientation. You can use the keys on the TV to switch the TV on. • Unplug the mains cord, wait for one minute and plug in the mains again. The TV does not react on the remote control • Verify if the batteries of the remote control are not empty or weak.
03-07-2007 11:57 Pagina 45 The picture position on screen is not correct • Some picture signals from some devices do not fit the screen correctly. You can shift the picture with the navigation key on the remote control. Check the signal output of the device. Sound There is a picture but no sound • Verify the volume is not set to 0. • Verify the sound has not been muted with the ¬ key. • Verify if all cables are connected properly.
2661.
03-07-2007 11:57 M Mains cord 8 Menu key 14 Mono 19 Movie expand 18 MPEG artefact reduction 17 Music 27 Mute key 12 N Naming devices 41 Noise reduction 17 O OK key 12 On timer 24 Pagina 47 Set code 24 Settings assistant 16 Sharpness 17 Sleeptimer 24 Software update 28 Sound menu 18 surround mode 19 Standby 12,24 Super zoom 18 Stationary images 3 Stereo 19 Subtitle 25 shift 18 Switch on 8 ENGLISH 2661.
2661.
