LCD TV User Manual 26PF5320 32PF5320 32PF7320
Contents Thank you for purchasing this television set. This handbook has been designed to help you install and operate your TV set. We would strongly recommend that you read it thoroughly. Table of Contents Important information Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Presentation of the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information • Disconnect mains plug when: – the red light below the TV screen is flashing continuously. – cleaning the TV screen. Never use abrasive cleaning agents. – there is a lightning storm. – the set is left unattended for a prolonged period of time. • No naked flame sources, such as lighted candles, should be placed on top of the TV or in the vicinity. • Do not place your TV set under direct sunlight or heat.
Presentation of the LCD TV LCD TV buttons: • POWER: to switch the TV on or off. • VOLUME –/+: to adjust sound level. • MENU: to access or close menus. The PROGRAM –/+ buttons can be used to select an adjustment and the VOLUME –/+ buttons to make that adjustment. • PROGRAM –/+: to select programmes. Rear of set The main connections are made at the bottom and the rear of the LCD TV. For more details on connections see Quick Use Guide.
Remote Control Buttons for LCD TV Functions 1) 2) (STANDBY) To set the TV to standby mode. To switch the TV set on again, press P –/+ or 0 to 9 buttons or AV button. Pixel + (only available on certain models/ versions) Switches the Pixel + demonstration mode on or off. 3) ® IÒ ‡ π †I º Peripheral device buttons (Refer to “Mode selector” on page 5) 4) Q Surround mode To activate / deactivate the surround sound effect. In stereo, this gives the impression that the speakers are further apart.
Remote Control Buttons for LCD TV Functions 12) Mode* Press this button to switch between TV, DVD or AUX. 13) 14) 15) 16) PIP on/off (refer to page 12) (12 List of programmes (13 To display / clear the list of programmes. Use the buttons Îï to select a programme and the button Æ to display it. Screen Format (refer to page 13) Sound mode Used to force programmes in Stereo and Nicam Stereo to Mono or, for bilingual programmes, to choose between Dual5or Dual6.
Installing your LCD TV Positioning the television set Place your TV on a solid stable surface. To avoid danger do not expose the TV to water, or heat source (e.g. lamp, candle, radiator). Do not obstruct the ventilation grid at the rear. Connecting the aerials • Use the aerial connection lead and connect the : socket situated at the bottom of the TV to your aerial socket. • Connect the power lead to the television and the mains plug into the wall socket (220-240 V 50/60 Hz).
Selecting the Menu Language Before you proceed to do the Automatic Installation of TV Programmes, select the menu Language of your choice. TV Menu Picture Sound Features Install Install Language Auto Store Manual Store Sort Name Channel Edit English Æ Æ Æ Æ Æ Press the MENU button. The TV Menu is displayed on the screen. Use the Î/ï button on the remote control to select the Install. Press the Æ button to access the Install menu (Language is highlighted). Select your language using the Í/Æ button.
Naming of Channel Name feature allows you to enter a name for any channel you select. Press the MENU button. Use the Î/ï button on the remote control repeated until Install is selected and press the Æ button to access Install menu. TV Menu Picture Sound Features Install Install Language Auto Store Manual Store Sort Name Channel Edit Æ Æ Æ Æ Æ 2 Press ï button repeatedly until Name is selected and press Æ button to access name mode. Use the Î/ï button to key in first character.
Manual Store Manual Store feature allows you to store the programmes one at a time. Press the MENU button. Use the Î/ï button repeatedly until Install is selected and press Æ button to access Install menu.
Picture Settings Press the MENU button. The TV Menu is displayed on the screen (Picture is highlighted). Press Æ button to access Picture menu. TV Menu Picture Sound Features Install Picture Brightness Colour Contrast Sharpness Hue ColourTemp. 39 Æ Æ Æ Æ Use the Î/ï button to select a setting and the Í/Æ button to adjust. To exit the menu, press Ë button. Description of the adjustments: • Brightness: this changes picture brilliance. • Colour: this changes the intensity of the colour.
Timer Feature The Timer feature allows you to set the timer to switch to another programme at a specified time when you are watching another programme or from standby mode. For the timer to function, the set must not be switched off. Once the set is switched off, the timer is disabled.
Using the Active Control Feature This feature automatically adjust the picture setting for optimal picture quality continuously under any signal conditions. You can select the Active Control On mode or the Active Control ON With Sensor mode. Active Control If Control On With Sensor mode is selected, the sensor will sense and adjust picture setting according to the lighting conditions of the room. You can also select to Active Control Off mode to switch off Active control function.
Screen Formats The pictures you receive may be transmitted in 16:9 format (wide screen) or 4:3 format (conventional screen). 4:3 pictures sometimes have a black band at the top and bottom of the screen (letterbox format). This function allows you to optimise the picture display on screen.
Using the Teletext If a TV channel broadcast contains teletext information, each channel that broadcasts teletext transmits a page (index page) with information on how to use the teletext system, usually on page 100. The system transmitted is indicated in the option line at the bottom of the screen. On/Off teletext Selecting a teletext page Press the button once to switch on teletext display. (Select a channel in which teletext is being transmitted).
Using the Teletext Main Index Press the button to return to the main index page. Dual Page Text Press button to display or exit dual page text mode. The active page is displayed on the left and the following page is displayed on the right. Press ( Hold) button if you want to hold a page (contents page). The active page is now displayed onthe right. To return to normal mode, press ( Dual page / 4) button.
Smart Picture and Sound Feature Smart Picture feature offers you a choice of 5 picture settings, namely, Rich, Natural, Soft, DVD/VCD and Personal. Smart Sound feature offers you a choice of 4 sound settings namely, Theatre, Music, Voice and Personal. Press or button repeatedly to cycle through the settings to select your desired mode. Defintion of Picture Settings Personal : Picture settings are set to your preference. Rich : Emphasize very vibrant colours.
Using the TV as a PC Monitor NOTE – When using the LCD TV as a PC monitor, slight diagonal interference lines may be observed when it is operated under electromagnetic interference environment but will not affect the performance of this product. – For better performance, good quality HDMI/DVI/VGA cable with good noise isolation filter is recommended. Choosing PC-VGA mode Press the AV button on the remote control to display the Source List.
Using in HD (High Definition) Mode HD Mode The HD (High Definition) mode allows you to enjoy clearer and sharper pictures through the CVI-1, CVI-2 or HDMI input if you are using a HD receiver/equipment that can transmit high definition programming. You must connect the HD equipment (see Quick Use Guide). Using the HD menus Press the MENU button to access the HD menu.
Tips No power • Check the TV’s AC power cord is plugged into the mains socket. If there is still no power, disconnect plug. Wait for 60 seconds and re-insert plug. Switch on the TV again. Poor reception • The proximity of mountains or high buildings may be responsible for ghost pictures, echoing or shadows. In this case, try manually adjusting your picture: refer to “Fine Tune” on page 9 or modify the orientation of the outside aerial.
Tips PC and PIP modes don’t work? • Check that you have configured the computer on a compatible display resolution (refer to page 15). Standby • If the set receives no signal for 15 minutes, it automatically goes into standby mode. To save power, your set is fitted with components that give it a very low power consumption when in standby mode (less than 1 W). Cleaning the set • Only use a clean, soft and lint-free cloth to clean the screen and the casing of your set.
Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. 2005 © Koninklijke Philips Electronics N.V. All rights reserved. www.philips.
