Technical data

3
200WP7 LCD
Go to cover page
Technical Data
"
"
'
ELECTRICAL SPECIFICATION
1. General
1.1. Product description
The Hudson 7, 20.1 WSXGA TFT flat panel monitor isspecified
as a display peripheral with Analog video signal input, Digital
video input 20.1 T FT LCD display.
Horizontal scanrangeis 30 - 98K Hz and refreshrangeis
56 - 76 Hz. Thisscanrangeallows it to display resolution upto
1680*1050 non-interlaced
at 60 Hz refreshrate. The image
can beadjustthrough OSDcontrol, theseadjustments can be
stored on an boardmemory including 40 preset modes
and15factory preset modes.
All optical characteristics(including WHITE-D,Brightness, and
soon) are determined according to panel specification af
ter
warming up approximate 30 minutes that brightness stability is
optimal, andfollows strictly after panel specification
1.2 Destination:
1.3. Basic data
1.3.1 LCD panel
Type NR. :M201EW01V0(AUO)
Outside dimensions : 459.4(H)*296.4(V)*22.8(D)(Typ)mm
Pixel Pitch ( mm ) : 0.258 mm x 0258mm
Color pixel arrangement :RGB vertical s
tripes
Displaysurface : low reflection, antiglare with hard coating
Color depth :16.7M colors(8bits)
Backlight :Six CCFL s
Active area(WxH) : 433.44x270.9mm (20.1 W diagonal)
View angle :Horizontal 176& Vertical 176 degree (CR>=10)
Contrastratio : 800:1 (Typ),400:1(min)
White luminance :Panel original color >240nits(min), 300 nits(Typ.)
1.3.2. Power supply
Main voltage : AC 90 - 135 Vrms and 170 - 264 Vrms, 50/60±2Hz
Power cord length :1.8M
Power cord type :3leadwith earth plug
Power indicator :LED (ON: green,Standby: amber,NEWMODE: flashing
Green twice per secondbefore user adjusts andsave it).
Auto power saving : EPA, Nutek, VESA DPMS
"
Mode HSYNC VSYNC Video Pwr-cons. Indication Rec.
time
Power-On On Onactive<60W
< 48W
w/o USB
Green
LED
Off Off On blanked<2.0W Amber
LED
<3s
Off On Off blanked<2.0W Amber
LED
<3s
Off Off Off blanked<2.0W Amber
LED
<3s
DCPower
Off
N/A < 1.0 W LED Off
1.3.3. Horizontal scan :30-98KHz
1.3.4. Vertical scan :56-76Hz
1.3.5. Input signals
1.Signal input level
Video :0.7Vp-p Linear /75ohms
Sync :H/H+V,VTTL level, composite sync,sync on green
Impedance
Video : Terminatedwith 75 ohms
Sync : Terminatedwith 2K2 ohms
The input signals can be applied in two different mode
s:
1). VESA Analog
Input signal:Video,Hsync., Vsync
Video:0.7Vp-p, inputimpedance,75ohms @DC
Sync.: Separate sync TTL level, inputimpedance 5k ohms
Hor.sync Positive/Negative
Ver.sync Positive/Negative
2). Intel DVI Digital
Input signal:Four channel TMDSsignals
1.3.6 Input connectors
(1) InputanalogD-sub connector pin assignment
PIN No. SIGNAL
1Red
2 Green/SOG
3Blue
4Sense (GND)
5NC
6Red GND
7 Green GND
8BlueGND
9 DDC+5V
10 Cable detect (GND)
11 Sense (GND)
12 Bi-directional data
13 H/H+V sync
14 V-sync
15 Data clock
(2) InputDVI-D connector pin assignment
Pin No. Description
1 TMDSdata2-
2 TMDSdata2+
3 TMDSdata2/4 shield
4NC
5NC
6 DDC clock
7 DDCdata
8NC
9 TMDSdata1-
10 TMDSdata1+
11 TMDSdata1/3 shield
12 NC
13 NC
14 +5V
15 Ground(return for +5V andH/Vsync)
16 Hot plug detect
17 TMDSdata0-
18 TMDSdata0+
19 TMDSdata0/5 shield
20 NC
21 NC
22 TMDS clockshield
23 TMDS clock+
24 TMDS clock-