Hudson 7 20.
200WP7 LCD Important Safety Notice Go to cover page Proper service and repair is important to the safe, reliable operation of all Philips Consumer Electronics Company** Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
Technical Data ELECTRICAL SPECIFICATION 1. 1.1. 1.2 General Product description The Hudson 7, 20.1" WSXGA TFT flat panel monitor is specified as a display peripheral with Analog video signal input, Digital video input 20.1" TFT LCD display. Horizontal scan range is 30 - 98K Hz and refresh range is 56 - 76 Hz. This scan range allows it to display resolution up to 1680*1050 non-interlaced at 60 Hz refresh rate.
Technical Data 200WP7 LCD Go to cover page Signal interface - 15Pins, D-sub male with DDC2B Pin assignments 24Pins, DVI-D male with DDC2B Pin assignments Sync polarity: -Hori.sync -Vert.sync positive/negative positive/negative 1.3.7.
Connection to PC 5 200WP7 LCD Go to cover page Installing Your LCD Monitor Front View Product Description 1 2 3 4 5 6 AUTO To switch monitor's power On and Off To access OSD menu To adjust the OSD To adjust brightness of the display To adjust the OSD Automatically adjust the horizontal position, vertical position, phase and clock setting Rear View Connect the cables to the back of your computer by following these steps: (a)Turn off your computer and unplug its power cord.
On Screen Display 200WP7 LCD Go to cover page Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On Screen Display 7 200WP7 LCD Go to cover page
200WP7 LCD Go to cover page On Screen Display
On Screen Display 9 200WP7 LCD Go to cover page
200WP7 LCD Go to cover page All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both Hipot and Ground Continuity testing. HI-POT TEST INSTRUCTION 1.Application requirements 1.1 All mains operated products must pass the Hi-Pot test as described in this instruction. 1.2 This test must be performed again after the covers have been refitted following the repair, inspection or modification of the product. 2. Test method 3.
200WP7 LCD Go to cover page Front View WAIT FOR AUTOMATIC ADJUSTMENT This screen appears when you press the "AUTO" buttons at the same time. It will disappear when the monitor is properly adjusted ATTENTION SIGNAL WAITING FOR AUTOMATIC ADJUSTMENT Access Aging.. Mode Step 1 : Turn off LCD monitor, and disconnect Interface Cable between Monitor and PC. Step 2 : [Push " "&" " buttons at the same time and hold it]+[Press power " " button until comes out " AGING screen" ] => then release all buttons.
200WP7 LCD Go to cover page Front Control Panel Access Factory Mode How to get into Factory Mode Menu Step1: Turn off monitor. Step2: [Push " "& " " buttons at the same time and hold it] +[Press power " " button untill comes out "Windows screen" ] => then release all buttons Step3: Press OK " " button, bring up Factory mode indication as shown in Fig2.
200WP7 LCD Go to cover page Philips' Flat Panel Monitors Pixel Defect Policy Black Dot Defects Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control. However, pixel or subpixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable.
Failure Mode Of Panel 200WP7 LCD Go to cover page Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical instruction on this manual to eliminate failure by replace LCD panel. Failure description Vertical block defect Polarizer has bubbles Phenomenon Polarizer has bubbles Vertical dim lines Foreign material inside polarizer. It shows liner or dot shape.
Troubleshooting 200WP7 LCD 15 Go to cover page This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Common Problems Having this problem No Picture Check these items · Make sure the power cord is plugged into the power outlet and into the back of the monitor.
200WP7 LCD 16 Troubleshooting Go to cover page Vertical flicker appears · Press the Auto button. · Eliminate the vertical bars using the Phase/Clock of More Settings in OSD Main Controls. Horizontal flicker appears · Press the Auto button. · Eliminate the vertical bars using the Phase/Clock of More Settings in OSD Main Controls. The screen is too bright or too dark · Adjust the contrast and brightness on Monitor Setup. (The backlight of the LCD monitor has a fixed life span.
Mechanical Instructions 17 200WP7 LCD Go to cover page 1.Back view as Fig.1 Fig.1 Fig.6 2.remove the base - Step 1: Place the monitor face down on a smooth surface as Fig 2. Be carefully to prevent the scratch and injury during the uninstallation. 3. Remove cable base as Fig7 and Fig.8 Unscrew the screws Fig.7 Fig.8 Fig.2 4.Remove back cover as Fig.9 and Fig.10 Fig.9 Step 2: Unfasten one screw on the base stand as Fig 3. Fig.3 Unscrew the 2 screws and open the clicks on the sides Fig.
200WP7 LCD Mechanical Instructions Go to cover page Fig.11 Fig.15 6.Remove the power board and scaler board -unscrew the screws and disconnect the connectors as Fig.13,Fig.14 8. Remove the control board -unscrew the screws and disconnect the connector as Fig.16 Fig.16 Fig.13 Fig.14 7.Reomve the USB board -Disconnect the connector and unscrew the screws as shown in Fig.
Display Adjustment 200WP7 LCD 19 Go to cover page TO access factory mode 1. Turn off monitor(do not turn off PC) 2. Press AUTO , OK and the power simultaneously on the frond control panel, then press OK wait till the OSD menu come on the screen of monitor. 2. Apply a 1280x1024/60Hz signal with white pattern.Set brightness control at 100% and contrast control at 50%. Adjust the R.G.B gain to reach special color temperature on center of screen. 2.1 Aim the probe CA-A30 at the center of screen as Fig. 4 2.
0WP7 LCD 20 Go to cover page 2.9 Adjust the R, G, B Sub-Gain on factory mode for the screen center, the 1931 CIE chromaticity (X, Y) co-ordinates shall be as follows. 9300°K 6500°K x (center) 0.283 ± 0.005 0.313 ± 0.005 y (center) 0.297 ± 0.005 0.329 ± 0.005 Use Minolta CA-110 for colour coordinates and luminance check. Luminance is > 250 Nits in the center of the screen when brightness at 100% and contrast set to 100%. sRGB x(center) 0.313 ± 0.008 y(center) 0.329 ± 0.
DDC Instructions 21 200WP7 LCD Go to cover page General Pin Assignment Input DVI-D connector pin assignment DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed"Analog DDC IC, & EEPROM". It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.
DDC Instructions 200WP7 LCD Go to cover page Configuration and procedure 3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID45 (for example, C:\EDID45, as shown in Fig. 7). There are 3 chips contained OSD string, serial number..etc on the circuit board, main EEPROM which storage all factory settings,OSD string. DDC IC which storage 128byte EDID data(serial number ..etc.).
DDC Instructions 23 200WP7 LCD Go to cover page Re-programming Analog DDC IC Step 3: Modify DDC data (verify EDID version, week, year) Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 11 1. 1=Power connector 2=D-SUB connector Click (new function) icon from the tool bar, bring up Step 1 of 9 as shown in Fig. 15 . EDID45 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9.
DDC Instructions 200WP7 LCD 24 Go to cover page 2. Access Factory Mode - Turn off monitor. - [Push AUTO " " & OK " " buttons at the same time and hold it ] + [Press power " " button untill comes out "Windows screen"] => then release all button 3. Click (Write EDID) icon from the tool bar to write DDC data. Step 6: Save DDC data Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below: Step 8: Modify serial number in OSD -1.
DDC Instructions 25 200WP7 LCD Go to cover page Re-programming Digital DDC IC Step 3: Modify DDC data (verify EDID version, week, year) Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 24 1. 1=DVI connector 2=D-SUB connector 3=Power Plug Click (new function) icon from the tool bar, bring up Step 1 of 9 as shown in Fig. 28 . EDID45 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9.
DDC Instructions 200WP7 LCD 26 Go to cover page Step 5: Write DDC data 1. Configuration should be as Fig. 31. And press OK. BOM Code Panel Supplier CODE AUO 1 CPT 2 LPL(LG) 3 QDI 4 CMO 5 BZ3A0601000001 SERIAL NO Fig. 31 SERVICE VERSION CHANGE CODE 2. Access Factory Mode - Turn off monitor. - [Push AUTO " " & OK " " buttons at the same time and hold it ] + [Press power " " button untill comes out "Windows screen"] => then release all button 3.
DDC Data 200WP7 LCD 27 Go to cover page THE DISPLAY DATA CHANNEL (DDC 2B) CONTENT INCLUDING (FOR HUDSON 7-200WP7 Analog AUO panel) ********************************************************************** EDID log file for 200WP7 Analog ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 0843 (HEX.) ID Serial Number : 123456 (DEC.
200WP7 LCD DDC Data Go to cover page THE DISPLAY DATA CHANNEL (DDC 2B) CONTENT INCLUDING (FOR HUDSON7-200WP7 Digital QDI panel) ********************************************************************** EDID log file for 200WP7 Digital ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 0843 (HEX.) ID Serial Number : 123456 (DEC.
ISP Instruction 200WP7 LCD 29 Go to cover page Double click the shortcut Configuration and procedure on the desktop Fig. 4 "Easywriter " The software is provided by Novatek to upgrade the firmware of CPU. It is a windows-based program, which cannot be run in MS-DOS. The tool (3138 106 10396) is for the interface between "Parallel Port of PC" and "15 pin-D-SUB connector of Monitor". To Printer port DC 8~12V DC 8~12V To Monitor D-sub/DVI cable System and equipment requirements 1. 2. 3. 4.
ISP Instruction 200WP7 LCD Go to cover page Press the file exit to end program, as shown in Fig.9 Fig.9 If there is a warring message coming as shown in Fig 10. , you have to check the AC power, Video cable, or Novatek MCU.
Electrical instructions 1. General points 1.1 Item H.Freq. (KHz) Mode Resolution V.Freq. (Hz) 9 48.363 VESA 1024x768 60.004 10 60.023 VESA 1024x768 75.029 11 68.700 MACINTOSH 1152x870 75.000 12 63.981 VESA 1280x1024 60.020 13 79.976 VESA 1280x1024 75.025 14 75.0 VESA 1600x1200 60 15 65.29 - 1680x1050 60.0 During the test and measuring, supply a distortion free AC mains voltage to the apparatus via an isolated transformer with low internal resistance. 1.
Electrical instructions 200WP7 LCD Go to cover page 25 67.500 VESA 1152x864 75.000 26 68.700 MACINTOSH 1152x870 75.000 x(center) 0.313 ± 0.008 27 61.845 SUN WS 1152x900 66.004 y(center) 0.329 ± 0.008 28 71.810 SUN WS 1152x900 76.150 Ynits 220 ± 10 29 60.000 VESA 1280x960 60.000 30 75.000 VESA 1280x960 75.000 31 63.981 VESA 1280x1024 60.020 32 71.691 SUN WS 1280x1024 67.189 33 76.000 DOS/V 1280x1024 72.000 34 79.976 VESA 1280x1024 75.025 35 81.
Repair Tips 33 200WP7 LCD Go to cover page 0. Warning preferably be equipped with a thermal control (soldering All ICs and many other semi-conductors are susceptible to temperature: 225 to 250 C). electrostatic discharges (ESD). Careless handling during - The chip, once removed, must never be reused. repair can reduce life drastically. When repairing, make sure 1.
200WP7 LCD Repair Tips Go to cover page 3. Lead-free product identification You can identify lead-free product by Philips-lead-free logo on PCB. P b 4. Lead-free product repair instruction 4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 149 00108(1.0mm SAC305). Remark: For lead free soldering material, please visit www.alphametals.com website for details. This is recommended by Philips. 4.2 Use only adequate solder tools applicable for lead-free soldering-tin.
Repair Flow Chart 200WP7 LCD Go to cover page AC IN Power Board Control Board Scaler Board LCD Panel No power (power indicator off) NG Check 12V/5V/3.
200WP7 LCD Repair Flow Chart 21 X Go to cover page NG Power Board Bad Power Board OK OK OK Check Scaler Board OK OK Bad Scaler Board
Repair Flow Chart OK OK OK Check Power Board OK Check LCD Panel Control Board OK OK Board 37 200WP7 LCD Go to cover page
200WP7 LCD Go to cover page 200WP7 Block Diagram Block Diagram Panel Backlight (3 CCFL) Panel • wire harness(LVDS) 30 Pin RGB//DE/Hsync/Vsync Panel Vcc (5V for QDI/AU) Scalar(LVDS interface) 30 pin wafer Connector Dual input Connector AC-DC Power supply Connector Inverter and DC-DC converter (132 mm x 75mm) Connector Connector (200mm x 150mm) Connector DVI_D D_SUB Connector AC input Panel Backlight (3 CCFL) Control Board USB Hub
Scaler Diagram-1 200WP7 LCD 39
200WP7 LCD Scaler Diagram-2
Scaler Diagram-3 200WP7 LCD 41
200WP7 LCD Scaler Diagram-4
Scaler Diagram-5 200WP7 LCD 43
200WP7 LCD Scaler Board C.B.A.
Scaler Board C.B.A.
200WP7 LCD Scaler Board C.B.A.
Power Diagram-1 200WP7 LCD 47
200WP7 LCD Power Diagram-2
Power Board C.B.A.
200WP7 LCD Power Board C.B.A.
200WP7 LCD 51
200WP7 LCD
200WP7 LCD 53
200WP7 LCD
200WP7 LCD 55
200WP7 LCD Go to cover page 21 X
GENERAL PRODUCT SPECIFICATION HUDSON7-200WP7 20.1" GENERAL PRODUCT SPECIFICATION . ANALOG AND DIGITAL DUAL INPUT . AUTO PICTURE ADJUSTMENT . 15 FACTORY PRESET MODES AND 40 PRESET MODES WHICH CAN BE RECOVERED TO PRESET MODES, 25 USER MODES . USER FRIENDLY OSD DISPLAY FOR MODE IDENTIFICATION /ADJUSTMENT . DDC 2B COMMUNICATION CAPABILITY . MAX. RESOLUTION 1680*1050 NON-INTERLACED AT 76 HZ . 20.1 "COLOR TFT LCD FLAT PANEL . EASY TILT & FOLDABLE BASE . FULL RANGE POWER SUPPLY 90 - 264 VAC .
GENERAL PRODUCT SPECIFICATION(Continued) 200WP7 LCD CONTENTS 1.0 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 Foreword Product profile LCD Scanning frequencies Video dot rate Power input Power consumption Dimensions Weight Functions Ambient temperature Regulatory compliance 3.0 3.1 3.1.1 3.2 3.2.1 3.2.2 3.2.3 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.4 3.5 3.6 3.6.1 3.6.
GENERAL PRODUCT SPECIFICATION 5.0 5.1 5.2 5.3 5.4 5.4.1 5.4.2 Mechanical characteristics Controls Unit dimension / weight Tilt and swivel base Transportation packages Shipping dimension / weight Block unit / palletization 6.0 6.1 6.2 6.3 6.4 6.4.1 Environmental characteristics Susceptibility of display to external environment Transportation tests Display disturbances from external environment Display disturbances to external environment EMI 7.0 7.1 8.0 8.1 9.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD 1.0 FOREWORD This specification describes a 20.1" WSXGA multi-scan color TFT LCD monitor with max. resolution up to 1680*1050/ 60 Hz(digital) /1680*1050/75Hz(analog) non-interlaced. All optical characteristics (including WHITE-D, Brightness, and so on) are determined according to panel specification after warming up approximate 30 minutes that brightness stability is optimal, and follows strictly after panel specification. 2.
GENERAL PRODUCT SPECIFICATION 2.5 2.6 2.8 Power consumption Dimensions Weight Functions : 200WP7 LCD : < 60W maximum with USB : 483(W) * 402(H) * 235(D) mm : 8.6Kg (1)D-SUB analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level, SOG sync (2)DVI digital Panel Link TMDS input (3) Audio Signal: PC line in 2.9 Ambient temperature: 0 ?C - 35 ?C 2.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD 3.0 Electrical characteristics 3.1 Interface signals The input signals can be applied in three different modes: 1). D-Sub Analog Input signal: Video, Hsync. , Vsync Video: 0.7 Vp-p, input impedance, 75 ohms @DC Sync. : Separate sync TTL level, input impedance 2.2k ohm terminate Hsync Positive/Negative Vsync Positive/Negative Composite sync TTL level, input impedance 5k ohm terminate (Positive/Negative) Sync on green video 0.3 Vp-p Negative (Video 0.
GENERAL PRODUCT SPECIFICATION Pin assignment: PIN No. 3.2.2 SIGNAL 1 Red 2 Green/ SOG 3 Blue 4 Sense (GND) 5 Cable detect 6 Red GND 7 Green GND 8 Blue GND 9 DDC +5V 10 GND 11 Sense (GND) 12 Bi-directional data 13 H/H+V sync 14 V-sync 15 Data clock DVI Cable The input signals are applied to the display through DVI-D cable. Length Connector type : 1.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD 18 3.2.3 TMDS data0+ 19 TMDS data0 shield 20 NC 21 NC 22 TMDS clock shield 23 TMDS clock+ 24 TMDS clock- USB Cable (High Full Speed) Length. : 1.8 M +/- 50 mm (Max.) Connector type. : USB- B Plug (Input) USB- A Plug (Output) Pin Assignment: Pin No. Description 1 VBUS 2 Data+ 3 Data- 4 GND 3.2.5 Software control functions via OSD/control adjustable functions: (1) PC Analog only Signal Input Mode Adjustable functions: 20.
GENERAL PRODUCT SPECIFICATION Main Menu Sub Menu Sub Menu 2 Exit 200WP7 LCD Description Default Default starting point Brightness & Contrast Brightness Sliding bar 100 Contrast Sliding bar 50 Color Original 9300K 6500K 6500K sRGB User define 20.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD R Sliding bar G Sliding bar B Sliding bar Position Position Horizontal Sliding bar Vertical Sliding bar More Settings Language English Left/right arrow to English select French German Italian Spanish Russian Phase Sliding bar Phase / Clock Clock Sliding bar OSD setting OSD position V OSD position H Sliding bar Reset (2) Digital interface OSD : Adjustable functions: 1st LEVEL 2nd LEVEL 3rd LEVEL MONITOR SETUP Exit Brightness & Contrast
GENERAL PRODUCT SPECIFICATION More Settings Language 200WP7 LCD /00,/05 : English, Spanish, French, German, Italian and Russian Phase/ Clock Phase Clock OSD Settings Horizontal Reset Vertical No Yes Serial No.: (Serial No.) Timing Mode Up/Down to Move, ok to Confirm . 3.3 Timing requirement 3.3.1 Mode storing capacity 1.) Factory preset modes : 15 2.) Preset modes : 40 3.) User define modes : 24 3.3.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD fv V-total (ms) V-sync width (ms) V-back porch (ms) V-video width (ms) V-front porch (ms) SYNC. H/V POLARITY SEP. SYNC 70Hz(70.09) 14.27(449 lines) 0.064(2 lines) 1.907(60 lines) 11.12(350 lines) 1.175(37 lines) +/- 70Hz(70.085) 14.27(449 lines) 0.064(2 lines) 1.112(34 lines) 12.71(400 lines) 0.381(13 lines) -/+ Y Y MODE NO. RESOLUTION 5 640 x 480 6 800 x 600 Dot clock (MHz) 31.500 60Hz(59.940) 16.683 (525 lines) 0.064 (2 lines) 1.049 (33 lines) 15.
GENERAL PRODUCT SPECIFICATION SEP. SYNC Y Y Y Y MODE NO. RESOLUTION 13 1280 x 1024 14 1600 x 1200 15 1680 x 1050 Dot clock (MHz) 135 162 146.249 f h (kHz) H-total (us) H-sync width (us) H-back porch (us) H-video width (us) H-front porch (us) 79.976kHz 12.504(1688 dots) 1.067(144 dots) 1.837(248 dots) 9.481(1280 dots) 0.119(16 dots) 75 13.333(2160 dots) 1.185(192 dots) 1.877(304 dots) 9.877(1600 dots) 0.395(64 dots) 65.29 15.316(2240 dots) 1.203(176 dots) 1.915(280 dots) 11.487(1680 dots) 0.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD 3.3.3 Horizontal scanning Sync polarity Scanning frequency : Positive or Negative : 30 - 98 K Hz 3.3.4 Vertical scanning Sync polarity Scanning frequency : Positive or Negative : 56 - 76 Hz 3.4 Power input connection Power cord length : 1.8 M Power cord type : 3 leads power cord with protective earth plug. 3.
GENERAL PRODUCT SPECIFICATION 4.1 200WP7 LCD Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal : As defined in 3.3, 1600x 1200 non-interlaced mode (75K/60Hz), signal sources must have 75 ohm output impedance. (2) Luminance setting: controls to be set to 200 nits with full screen 70 % duty cycle white signal (3) Warm up: more than 30 minutes after power on with signal supplied. (4) Ambient light: 400 -- 600 lux.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD and brightness at maximum. ) 4.4 4.4.1 Image size Actual display size 433.44 x 270.9mm 4.5 Brightness uniformity Set contrast at 100% and turn the brightness to get average above 250 nits (LPL), nits (AUO) nits at centre of the screen. Apply the Fig 1; it should comply with the following formula: Minimum luminance of nine points (brightness) X100% (Min.) Maximum luminance of nine points (brightness) LM201W01-SLA1 (LPL)-----70% (min.
GENERAL PRODUCT SPECIFICATION 6500K/ sRGB CIE coordinates X = 0.313 +/- 0.020 Y = 0.329 +/- 0.020 5.0 Mechanical characteristics 5.1 Controls Front side: - DC power switch - OSD function key (OK) - UP - DOWN - RIGHT - LEFT - AUTO Rear: - D-SUB - DVI-D - Power cord socket 5.2 Unit dimension / Weight Set dimension (incl. pedestal): 483(W) * 402(H) * 235(D) mm Net weight 5.3 : 8.6Kg (Including I/F cable 240 g) Tilt and swivel base Tilt angle : Swivel angle : 5.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD Gross weight : 10.7 KG 5.4.2 Block unit / Palletization sets/ layer 4 layers/ block 8 sets/ block unit 32 6.0 Environmental characteristics The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device. 6.
GENERAL PRODUCT SPECIFICATION test 30 G, 16 m-sec, 6 cycles Temperature : 23 Humidity : 60 % Air pressure : 100 kpa (According to DSD draft standard UAN-D636) 6.3 Display disturbances from external environment According to IEC 801-2 for ESD disturbances 6.4 Display disturbances to external environment 6.4.1 EMI EMI : C-tick, CE(Europe), FCC(USA), IC(Canada), VCCI(Japan), BSMI 7.0 Reliability 7.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD 10. LCD PANEL CHARACTERISTICS REQUIREMENTS LCD Panel Pixel Defect Requirement Acceptable Level Bright Dot Defects 1 lit subpixel 3 2 adjacent lit subpixels 1 3 adjacent lit subpixels (one white pixel) 0 Distance between two bright dot defects 25mm or more Bright dot defects within 20mm circle 3 or fewer Total bright dot defects of all types 3 Dark Dot Defects 1 dark subpixel 5 2 adjacent dark subpixels 2 20.
GENERAL PRODUCT SPECIFICATION 3 adjacent dark subpixels (one white pixel) 1 Distance between two black dot defects 15mm or more Total black dot defects of all types 5 Total bright or black dot defects of all types 5 *Note: 1 or 2 adjacent subpixel defects= 1 dot defect 20.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD Fig 1: Brightness Uniformity L/2 L/10 L W/10 1 2 3 4 5 6 W W/2 7 8 9 20.
GENERAL PRODUCT SPECIFICATION Fig 2: 200WP7 LCD Cross talk pattern Gray level 46 (64 Gray level) 1/6 1/2 YA 1/2 Fig 3: Cross-talk Pattern Center at Gray level 0 (Black) 1/3 1/3 1/6 1/3 1/2 1/3 YB 1/2 1/3 20.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD SEPARATE SYNC. VIDEO D C E HORIZONTAL B A VIDEO R Q S VERTICAL P O COMPOSITE SYNC. VIDEO C D E HORIZONTAL B A FIG-4 TIMING CHART -1 20.
GENERAL PRODUCT SPECIFICATION 200WP7 LCD VIDEO Q R S VERTICAL P O COMPOSITE SYNC. & VIDEO ( SYNC. ON GREEN ) HORIZONTAL B C E D A VERTICAL B S P Q R O FIG-5 TIMING CHART -2 20.
200WP7 LCD Go to cover page 0004 0030 0031 0032 0033 0040 0041 0042 0043 0051 313815761011 313815761221 313815418091 313815417771 313815417781 313815761001 313815417791 313815417811 313815133511 313815138241 SUPER ERGO BASE ASSY BEZEL ASSY-SILVER BEZEL-SLIVER BEZEL- DECO CONTROL KNOB BACK COVER ASSY-S BACK COVER MIDDLE COVER-SILVER VESA PLATE METAL FRAME 7201 7202 7351 7351 7353 7353 7401 7403 7405 7501 7502 7503 7504 7505 7506 7507 7508 7509 932214526668 932214526668 313815867291 932222343682 3138
200WP7 LCD Model:200WP7ES/00(AUO Panel) Mechanical Parts 0004 313815761011 SUPER ERGO BASE ASSY 0030 313815761221 BEZEL ASSY-SILVER 0031 313815418091 BEZEL-SLIVER 0032 313815417771 BEZEL- DECO 0033 313815417781 CONTROL KNOB 0040 313815761001 BACK COVER ASSY-S 0041 313815417791 BACK COVER 0042 313815417811 MIDDLE COVER-SILVER 0043 313815133511 VESA PLATE 0051 313815138241 METAL FRAME 0053 313815321301 INSULATE PLATE 0080 313815759083 SHIELDING ASSY 0090 313815136711 AC PLATE 0095 313815136721 DSUB PLATE 012
200WP7 LCD Go to cover page 3540 232270296001 RST SM 0603 JUMP.
Spare Parts List Model:200WP7ES/01(LPL Panel) 12NC: 8639 000 17096 Mechanical Parts 4 30 31 32 33 40 41 42 43 44 51 80 116 340 450 1057 313815761011 313815761221 313815418091 313815417771 313815417781 313815761001 313815417791 313815417811 313815133511 313815162071 313815138241 313815759083 313810440571 313815136703 313815642281 313815867411 SUPER ERGO BASE ASSY BEZEL ASSY-SILVER BEZEL-SLIVER BEZEL- DECO CONTROL KNOB BACK COVER ASSY-S BACK COVER MIDDLE COVER-SILVER VESA PLATE CONTACT SPRING METAL FRAME SH
Spare Parts List 200WP7 LCD Go to cover page 3305 3306 3307 3308 3309 3310 3311 3312 3313 3314 3315 3316 3317 3318 3319 3320 3321 3322 3323 3351 3352 3353 3354 3358 3359 3360 3361 3364 3365 3366 3367 3368 3369 3370 3371 3372 3373 3374 3379 3380 3382 3391 3392 3401 3402 3403 3405 3408 3409 3410 3411 3412 3413 3414 3416 3501 3502 3503 3504 3506 3507 3508 3509 3510 3511 3512 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3525 3526 3527 3532 3533 3539 212211805637 232270260101 232270260101 23227026010
200WP7 LCD Diversity of 200WP7EB/00 compared with 200P7ES/00 Item 12NC Description 863900017042 200WP7EB/00 0602 313811709571 E-D.F.U.
Scaler Diagram-1 200WP7 LCD 1 A 2 CONTENTS 3 4 5 A REVISION HISTORY SCHEMATIC Name SHEET Date Author Ver Comments 01. Contents 1 2005-09-14 Jerry Chen A PHILIPS UH7 200P7 SCALER SEHEMATIC FOR PROTOTYPE 02. DSUB/DVI 2 2005-11-23 Jerry Chen B PHILIPS UH7 200WP7 SCALER SEHEMATIC FOR 2nd MODEL 03. MCU 3 2006-02-09 Jerry Chen C 5205 /5206 /5207 change to 3215 /3216/3217 22R 04. SCALER 4 B B 05. DDR 5 06. IO 6 C Position Approval Signature C Date CP NR.
Scaler Diagram-2 1 2 3 4 5 200WP7 LCD 6 7 8 9 10 11 +5V_ESD 5201 1 1201 A 31 120 OHM 6202 BAS 32L 2 2201 BAS 32L 0.
Scaler Diagram-3 200WP7 LCD 1 2 3 4 5 6 7 VCPU 8 +3.3V A 1351 1352 1353 2351 2353 2354 2355 2356 2358 2359 2360 2361 2362 2363 3351 3352 3353 3354 3358 3359 3360 3361 3364 3365 3366 3367 3368 3369 3370 3371 3372 3373 3374 3379 3380 3381 3382 3391 3392 5351 7351 7353 5351 1 VCPU 2 120 OHM VCPU 3351 3370 10K?W 2353 22pF 2354 22pF 12.
Scaler Diagram-4 1 2 4 5 6 7 8 9 10 +3.3AVDD +5V +3.3VMST +3.3AVDD PANEL_VCC 5401 5414 120 OHM 5417 120 OHM (NC) 5403 1 1 +3.3AVDD_A 2 120 OHM +3.3AVDD 2 120 OHM 1 +3.3AVDD_D 2 120 OHM 1 1 1 5402 5413 100R A 4 + 2 3 GND Pad VI 2455 4.7uF/25V VO 2401 47U/25V +3.3VMST 2 2403 4.7uF/25V 2402 0.1uF/16V 2404 0.1uF/16V 2451 0.1uF/16V 2405 4.7uF/25V 2406 0.1uF/16V 2452 0.1uF/16V +3.3AVDD_P 2456 4.7uF/25V AP1117E33 2457 0.1uF/16V 2 7405 2 11 +3.3AVDD_M 1 +3.
Scaler Diagram-5 200WP7 LCD 1 2 3 4 5 6 7 8 9 10 11 5301 +2.5VDDR 1 +2.5V_DMQ 2 120 OHM 2302 0.1uF/16V A + 2303 22U/16V 2304 0.1uF/16V 2305 0.1uF/16V 2306 0.1uF/16V 2307 0.1uF/16V 2308 0.1uF/16V 2309 0.1uF/16V 2310 0.
Scaler Diagram-6 1 2 3 4 5 200WP7 LCD 6 7 8 9 10 11 +3.3V A 1501 1505 2501 2502 2503 2504 2505 2506 2510 2511 2515 2516 2517 2518 2519 2520 2521 2522 2523 2524 2525 2526 2529 2530 2531 2532 2533 2534 2535 2536 2537 2538 2539 3501 3502 3503 3504 3506 3507 3508 3509 3510 3511 3512 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3525 3526 3527 3529 3530 3531 3532 3533 3534 3535 3536 3537 3538 3539 5501 5502 5503 6501 7501 7502 7503 7504 7505 7507 7508 7509 7510 7511 7512 +3.
200WP7 LCD Scaler Board C.B.A.
Scaler Board C.B.A.
Updated Parts 200WP7 LCD Go to cover page According to the ECO-CA005956,Add QSG-ergo base and Jig on P.E. bag for 200WP7,Following is the detail 1.Item 0129 Qty from 1to 2, and add new Item: 0142-313815524581- QUICK SET GUIDE-ERGO BASE 2.
200WP7 LCD Manual 12NC(VERSION) 3138 106 10503 3138 106 10503 3138 106 10503 3138 106 10503 3138 106 10504 Release Date Apr-7-06 Apr-20-06 Apr-28-06 Jun-02-06 Dec-04-06 97 Change Instruction Initial Release Panel changed(P84) Add QSG-ergo base and Jig on P.E.
