32HFL2808D/12 39HFL2808D/12 EN User Manual Studio 32/39HFL2808D/12 Page |1
For support, please check your warranty card or www.philips.com/support.
Contents 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Important Information Notice Sustainability Help and support TV Control switch & Operation Stand Installation/Un-Installation Viewing remote control Viewing the connections Switching On/Off First Time Installation Media Playback via USB input TV Features and Functions Software Upgrade Specifications Supported File Formats and Compatibility TV Menu Professional Mode HotelTV Options Studio 32/39HFL2808D/12 4 5 6 6 7 8 9 10 11 11 12 13 17 19 21 23 26 Page
Important Information Important information Safety Read and understand all instructions before you use your TV. If damage is caused by failure to follow the instructions, the warranty does not apply. Risk of electric shock or fire! Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
Risk of hearing damage! Avoid using earphones or headphones at high volumes or for prolonged periods of time. Low temperatures If the TV is transported in temperatures below 5°C or 41°F, unpack the TV and wait until the TV temperature matches room temperature before connecting the TV to the power outlet. Terms of warranty Screen care Risk of damage to the TV screen! Never touch, push, rub or strike the screen with any object. Unplug the TV before cleaning.
Philips is committed to develop, produce and market products that cause no adverse health effects. TP Vision confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today. Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardisation for early integration in its products.
Important information General Operation TV Control switch & Operation Installing the Batteries to the Remote 1. 2. 3. Up direction Down direction Program switch Lift the cover on the back of the remote upward gently. Install two AAA batteries. Make sure to match the + and - ends of the batteries in the battery compartment (observe the correct polarity). Replace the cover. Program switch can control: Volume/ AV / Standby-On Note: You can move the switch, upward or downward to change the volume.
Detachable Stand Installation Method 1. TV is laid on a flat surface. Make sure that there are no objects on the table that can damage/harm the TV 2. Position the stand so that it coincides with the stand mounting points (4x) on the TV. Once it is positioned fix the stand with four screws to the TV. 4 screw holes for fixing stand to TV Detachable Stand Un-Installation Method 1. TV is laid on a flat surface. 2. Remove four screw that fix stand to TV. 3. Stand is pulled back. 4. Stand is detached.
Viewing remote control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Teletext / mix Standby Image Size Sleep Timer Info/ Reveal (in TXT mode) Source selection Yellow button/Current language (in DVB Channel) / Mono-Stereo Dual I-II (in Analog Channel) Blue button Green button Red button Navigation buttons / Subpage (in TXT mode) OK / Hold (in Text mod) /Channel List Return /Back /Index page (in TXT mode) Electronic Programme Guide Menu on/off Mute Programme up/down Previous Programme/ Now (in EPG mode)
Viewing the connections Connector Type Cables (Not supplied) Device Scart Connection (back) VGA Connection (back) PC/YPbPr Audio Connection (side) HDMI Connection (back) SPDIFF Connection (back) Side AV Connection (side) Headphone Connection (side) USB Connection (side) CI Connection (side) NOTE: When connecting a device via the Side AV input, you must use the supplied connection cables to enable connection. See the illustrations above.
Switching On/Off To Switch the TV On Note: Connect the power cord to the 220-240V AC, 50 Hz. Then the standby LED lights up. To switch on the TV from standby mode either: o Press the “ ” button, P/CH- or P/CH+ or a numeric button on the remote control. o Press the control switch left side of the TV. The TV will then switch on. If you switch on your TV via CH- or CH+ buttons on the remote control or on the TV set, the program that you were watching last will be reselected.
Additionally, for some countries, Network ID option will be available. Network ID feature gets the Network Information Table. This table provides information on the selected network. It may change according to the operator and the region where that operator actively broadcasts. When finished, press OK button to start automatic search. The TV will search and store available broadcasts.
TV Features and Functions Picture Menu Contents Mode Contrast Brightness Sharpness Colour Power Save Mode Backlight (optional) Noise Reduction Advanced Settings Reset For your viewing requirements, you can set the related mode option. Picture mode can be set to one of these options: Cinema, Game, Sports, Dynamic and Natural. Sets the lightness and darkness values of the screen. Sets the brightness value for the screen. Sets the sharpness value for the objects displayed on the screen.
TV Menu Features and Functions Sound Menu Contents Volume Equalizer: Balance Headphone Sound Mode AVL Headphone/Lineout Dynamic Bass Surround sound Digital Out Adjusts volume level. In equalizer menu, the preset can be changed to Music, Movie, Speech, Flat, Classic and User. Press “OK” to enter the menu. Press the “MENU” button to return to the previous menu. Equalizer menu settings can be changed manually only when the Equalizer Mode is in User.
TV Menu Features and Functions Settings Menu Contents Conditional Access Language Parental Timers Recording Configuration Date/Time Sources Controls conditional access modules when available. Configures language settings (-may change depending on the country selected) Preferred and current settings will be available. Current settings can be changed only if the broadcaster supports. Configures parental settings. (see page 14) Sets timers for selected programs.
Store mode Power Up Mode If enabled will store changes to channels are made. Power up of TV will be Standby mode or Last Status at moment of power down. TV Menu Features and Functions Install and Retune Menu Contents Automatic Channel Scan (Retune) Displays automatic tuning options. Digital Aerial: Searches and stores aerial DVB stations. Digital Cable: Searches and stores cable DVB stations. Analogue: Searches and stores analogue stations.
Electronic Program Guide Some, but not all channels send information about the current and next programs. Press the “EPG” button to view the EPG menu. Up/Down/Left/Right: Navigate EPG. OK: Displays program options. INFO: Displays, in detail information on program selected. GREEN: Switches to List Schedule EPG. YELLOW: Switches to Timeline Schedule EPG. BLUE: displays filtering options. Program Options IMPORTANT In EPG menu, press the OK button to enter the Event Options menu.
Troubleshooting & Tips Image persistence – ghosting Please note that ghosting may occur while displaying a persistent image (still or paused image). LED TV’s image persistence may disappear after a short time. Try turning off the TV for a while. To avoid this, do not leave the screen in still picture mode for extended periods. No power If your TV has no power, please check the power cord plug is connect to the mains power socket. Poor picture 1. Have you selected the correct TV system? 2.
Specifications TV BROADCASTING PAL/SECAM B/G D/K K’ I/I’ L/L’ DIGITAL RECEPTION DVB-T MPEG2 DVB-T MPEG4 HD DVB-T MHEG-5 Engine (for UK only) DVB-C MPEG2 DVB-C MPEG4 HD RECEIVING CHANNELS VHF (BAND I/III) UHF (BAND U) HYPERBAND NUMBER OF PRESET CHANNELS 1000 (800 DVB-T / 200 Analogue) CHANNEL INDICATOR On Screen Display RF AERIAL INPUT 75 Ohm (unbalanced) OPERATING VOLTAGE 220-240V AC, 50 Hz.
Supported DVI Resolutions PC Typical Display Modes When connecting devices to your TV’s connectors by using DVI to HDMI cables (not supplied), you can refer to the following resolution information The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions. Your TV supports up to 1920x1080.
Supported File Formats for USB Mode Media Motion JPEG .asf, .wmv .fla, .flv File Extension Format Video codecs MPEG1,2 MPEG2 H.264, MPEG1,2,4 MPEG2, H.264, VC1, AVS, MVC Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1/2 H.264 MPEG2, MPEG4 Xvid 1.00, Xvid 1.01, Xvid 1.02, Xvid 1.03, Xvid 1.10-beta1/2 H.264 JPEG VC1 H.264, Sorensen H.263 Audio Codecs .mp3 MPEG1/2 Layer 1 File Extension .mpg, .mpeg, .dat .vob .mkv .ts .avi Movie .mp4 Media Music Media AC3, EAC3 .m4a, .aac M4A/AAC .
AV and HDMI Signal Compatibility Source EXT (SCART) Side AV YPbPr HDMI1 Supported Signals PAL 50/60 NTSC 60 RGB 50 RGB 60 PAL 50/60 NTSC 60 480I 480P 576I 576P 720P 720P 1080I 1080I 1080P 1080P 480I 480P 576I 576P 720P 720P 1080I 1080I 1080P 1080P 1080P 1080P 1080P 60Hz 60Hz 50Hz 50Hz 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 60Hz 60Hz 50Hz 50Hz 50Hz 60Hz 50Hz 60Hz 24Hz 25Hz 30Hz 50Hz 60Hz Available O O O O O O O O O O O O O O O O O O O O O O O O O O O O O (X: Not Available, O: Available) In some cases a signal o
TV Menu Professional Mode Features and Functions Hotel Setup RC (22AV8573) Standard RC Enter Hotel TV Menu It is only possible to enter the Hotel TV Menu for the Professional Mode using the optional HotelTV SetUp Remote Control (22AV8573). To exit the Hotel TV menu with standard RC: press Menu key To enter the Hotel TV menu: press RC5 Setup key press Home/Menu key Note: Only the Home/Menu key on the HotelTV SetUp RC (22AV8573) will control the TV.
Hotel TV Menu settings Feature to enable or disable the Hotel TV Menu features. Hotel Mode • When enabled the TV will follow configured feature settings. [Off] Note: Access to the Hotel TV Menu is by the use of on the HTV Setup RC or on the standard RC using key sequence: Menu 7 9 3 5. Below settings are only active while [Hotel Mode] is On. Pin8 Last Status Panel Lock RCU Inhibit Feature to enable or disable the auto SCART feature.
Hotel TV Menu settings Feature to hide menu items when the Remote Control Menu key is pressed. • Disable All Menus OSD Disable [Disable All Menus] ○ all menu icons are hidden. • Disable Setup Menus ○ picture, sound, settings and media browser menu icons are displayed. When [Hotel Mode] is set to Off, all TV menu items will be displayed (picture, sound, settings, install and retune, channel list, media browser) Feature to hide Teletext display.
HotelTV Options Service Menu Enter Service Menu It is only possible to enter the Service Menu if the Hotel Mode is disabled, Hotel Mode set to . If enabled, open the Hotel TV Menu and set Hotel Mode to Off. To enter the Service Menu: press Menu key press key sequence: <1><2><3><6><5><4> All items are unselectable under the Service Menu. The software version number will shown as VES11E_x.y.
