Specifications

3
TPT1.0A LA
1. Technical Specifications and Connections
1.2.2.1.2TV mode signal type
RF Signal : Aerial input / 10mV(30-100dBuV)
Video signal : CVBS input ( RCA jack) / 1Vpp (300mV-sync,
700mV-video.)
S video input / 1VppY-signal, +/-300mV C-signal
SCART input: CVBS
S SRGB signal ( for WE model only)
Comp video in(YPbPr input)/ 1Vpp Y signal, +/-350mV Pb,Pr signal
HDMI:Digital interface with 4 channels TMDS signal
CVBS output ( RCA jack) / 1Vpp (300mV-sync, 700mV-video.)
Audio signal : Audio (1) R/L for AV IN(AV and S-Video).
Level: - Nominal : 0.5 V rms.
- Maximum : 1.5 V rms.
- Impedance > 10 k
.
Audio (2) R/L for SCART IN
Level: - Nominal : 0.5 V rms.
- Maximum : 1.5 V rms.
- Impedance > 10 k
.
Audio (3) R/L for Comp video IN.
Level: - Nominal : 0.5 V rms.
-Maximum : 1.5 V rms.
- Impedance > 10 k
.
Audio (4) digital audio for HDMI Video IN.
1.2.2.1.3 PVR (CVBS) output:
Video: CVBS output 1Vpp / Impedance : 75
.
Audio: R/L output (from CVBS)
Level: - Nominal : 0.5 V rms.
- Maximum : 1.5 V rms.
- Impedance < 1 k
.
1.2.2.1.4 Scart output: ( for WE model only)
Video: CVBS output 1Vpp / Impedance : 75
.
Audio: R/L output (from CVBS)
Level: - Nominal : 0.5 V rms.
- Maximum : 1.5 V rms.
- Impedance < 1 k
.
1.2.2.1.5 SPDIF output: Serial digital audio output when input is HDMI.
1.2.2.1.6 Headphone
Audio: R/L output -10mW at 32
.
3.5mm stereo jack with switch
Impedance is between 8 and 600
.
1.2.2.2 TV system signal mode:
RF support:
China : PAL(D,K)
WE : PAL and SECAM(France).
CVBS/S-video: Support PAL, NTSC and SECAM colour system.
Comp video IN(YpbPr) : SDTV and HDTV, including 480i/p, 576i/p,
720p 50/60Hz, 1080i 50/60Hz.
HDMI IN : 480P, 576P ,720P/50Hz , 720P/60Hz , 1080i/50Hz ,
1080i/60Hz
PVR (CVBS out) : Support PAL, NTSC and SECAM colour system.
1.2.2.3 Signal cable
1.2.2.3.1 VGA signal cable
The input signals are applied to display through D-sub cable.
Length: 1.8 M +/- 50 mm (fixed)
Connector type: D-sub male.
With DDC_2B pin assignments.
Blue connector thumb-operated jackscrews
15-pin D-sub VGA connector of the signal cable:
1 Red video input
2 Green video input /SOG
3 Blue video input
4 GND
5 GND- cable detect
6 Red video ground
7 Green video ground
8 Blue video ground
9 DDC +3.3V (or 5V)
10 Logic ground
11 GND
12 Serial data line (SDA)
13 H. Sync / H+V
14 V. Sync
15 Data clock line (SCL)
1.2.2.3.2 HDMI for digital Video / Audio interface with pin assignment
as follows:
Pin No. Description
1RX2+
2GND
3RX2-
4RX1+
5GND
6RX1-
7RX0+
8GND
9RX0-
10 RXC+
11 GND
12 RXC-
13 CEC
14 NC
15 DDC clock
16 DDC data
17 GND
18 +5V POWER
19 Hot Plug Detect
1.2.2.3.3 CVBS
The input signals are applied to display through CVBS cable
Pin assignment
PIN NO. SIGNAL
1GND
2 CVBS
3 CVBS
4 CVBS
1.2.2.3.4 S-Video
The input signals are applied to display through S-Video cable
Pin assignment
PIN NO. SIGNAL
1GND
2GND
3GND
4GND
5GND
6LUMA
8 CHROMA