E Line 345E2 www.philips.
Table of Contents 1. Important........................................ 1 1.1 Safety precautions and maintenance................................... 1 1.2 Notational Descriptions.............. 3 1.3 Disposal of product and packing material............................................ 4 2. Setting up the monitor................ 5 2.1 Installation...................................... 5 2.2 Operating the monitor................. 6 2.3 Remove the Base Assembly for VESA Mounting.............................
1. Important 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user's manual before you use your monitor. It contains important information and notes regarding the operation of your monitor.
1. Important screen for a constant period of time by : • If your monitor gets wet, wipe it with dry cloth as soon as possible. • Looking at something varying distances after a long period focusing on the screen. • • Conscious Blinking often while you work. • Gently closing and rolling your eyes to relax. If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord.
1. Important may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 1.2 Notational Descriptions Service Notes, Cautions and Warnings • The casing cover should be opened only by qualified service personnel. • If there is any need for any document for repair or integration, please contact with your local service center.
2. Setting up the monitor Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. 1.3 Disposal of product and packing material Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor 2. Hold the base stand with both hands and firmly insert the base stand into the base column. (1) Gently attach the base to the stand. 2. Setting up the monitor 2.1 Installation (2) Use your fingers to tighten the screw located at the bottom of the base. Package contents E line 345E2AE (3) Use a screwdriver to tighten the screw located at the bottom of the base, and secure the base to the stand tightly. Quick Start Register your product and get support at www.philips.
2. Setting up the monitor Connecting to your PC 2.2 Operating the monitor Description of the control button 1 7 6 5 4 3 2 Kensington anti-theft lock Earphone jack Audio in DisplayPort input HDMI 2 input 6 HDMI 1 input 7 AC/DC power input Press to switch power on. Press more than 3 seconds to switch power off. Access the OSD menu. Confirm the OSD adjustment. Adjust the volume level. Adjust the OSD menu. Connect to PC 1. Change the signal input source. Adjust the OSD menu.
2. Setting up the monitor Description of the On Screen Display Main menu What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor Resolution notification 2.3 Remove the Base Assembly for VESA Mounting This monitor is designed for optimal performance at its native resolution, 3440 x 1440 When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 3440 x 1440 for best results. Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. 2.4 MultiView VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 100mm What is it? Multiview enables active variety connect and view so that you can work with multiple devices like PC and Notebook side-by-side simultaneously, making complex multi-tasking work a breeze.
2. Setting up the monitor 1. Toggle to the right to enter OSD Menu Screen. When the sub source is not detected. 2. Toggle to the up or down to select main menu [PIP / PBP], then toggle to the right to confirm. 3. Toggle to the up or down to select [PIP / PBP Mode], then toggle to the right. Note The black strip shows on the top and the bottom of the screen for the correct aspect ratio when in the PBP mode.
2. Setting up the monitor Top-Left B A Top-Right B A (main) (main) Bottom-Left B • A Bottom-Right A (main) B (main) Swap: The main picture source and the sub picture source swapped on the display. Swap A and B source in [PIP] mode: B A (main) A ↔ B (main) Swap A and B source in [PBP] mode: A • (main) B ↔ B (main) A Off: Stop MultiView function. A (main) Note When you do the SWAP function, the video and its audio source will swap at the same time.
3. Image Optimization How to enable SmartImage? 3. Image Optimization 3.1 SmartImage What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized monitor performance. 1. Toggle to the left to launch the SmartImage on screen display. 2.
3. Image Optimization portion can be highlighted for RTS games (through SmartFrame). The picture quality can be adjusted for the highlighted portion. • Gamer 1: User’s preference settings saved as Gamer 1. • Gamer 2: User’s preference settings saved as Gamer 2. • LowBlue Mode: LowBlue Mode for easy on-the-eyes productivity Studies have shown that just as ultra-violet rays can cause eye damage, shortwave length blue light rays from LED displays can cause eye damage and affect vision over time.
3. Image Optimization • AMD Radeon R7 260X • AMD Radeon R7 260 3.3 Adaptive Sync ■■ Processor A-Series Desktop and Mobility APUs Adaptive Sync • • • • • • • • • PC gaming has long been an imperfect experience because GPUs and monitors update at different rates. Sometimes a GPU can render many new pictures during a single update of the monitor, and the monitor will show pieces of each picture as a single image. This is called “tearing.
4. Technical Specifications 4. Technical Specifications Picture/Display Display Panel Type Backlight IPS technology W-LED system Panel Size 34” W (86.36 cm) Aspect Ratio Pixel Pitch Contrast Ratio (typ.) Optimum Resolution Viewing Angle Picture Enhancement Flicker free Display Colors Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode EasyRead Connectivity Signal Input Audio In/Out Input Signal Convenience Built-in speaker MultiView 21:9 0.2325 x 0.
4. Technical Specifications Heat Dissipation* Normal Operation Sleep (Standby) Off Power LED indicator Power Supply AC Input Voltage AC Input Voltage AC Input Voltage at 100VAC , 50Hz at 115VAC , 60Hz at 230VAC , 50Hz 129.0 BTU/hr (typ.) 128.7 BTU/hr (typ.) 128.3 BTU/hr (typ.) 1.71 BTU/hr 1.71 BTU/hr 1.71 BTU/hr 1.02 BTU/hr 1.02 BTU/hr 1.
4. Technical Specifications 4.1 Resolution & Preset Modes Maximum Resolution 3440 x 1440 @ 75 Hz Recommended Resolution 3440 x 1440 @ 60 Hz H. freq (kHz) Resolution V. freq (Hz) 31.47 720x400 70.09 31.47 640x480 59.94 35.00 640x480 66.67 37.86 640x480 72.81 37.50 640x480 75.00 35.16 800x600 56.25 37.88 800x600 60.32 48.08 800x600 72.19 46.88 800x600 75.00 47.73 832x624 74.55 48.36 1024x768 60.00 56.48 1024x768 70.07 60.02 1024x768 75.03 44.77 1280x720 59.86 63.
5. Power Management 5. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
6. Customer care and warranty together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 6. Customer care and warranty 6.1 Philips’ Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products.
6. Customer care and warranty Three adjacent lit sub pixels (one white pixel). Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
6.
6. Customer care and warranty 6.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For Warranty Period please refer to Warranty Statement in Important Information Manual. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center.
7. Troubleshooting & FAQs 7. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. 7.1 Troubleshooting Visible signs of smoke or sparks This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.
7. Troubleshooting & FAQs • Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “after-image” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 7.2 General FAQs Q1: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? Ans.: Recommended resolution for this monitor: 3440 x 1440.
7. Troubleshooting & FAQs Ans.: Y es, you can change your color setting through OSD control as the following procedures, • Press to show the OSD (On Screen Display) menu disk when you first install your monitor. Follow the instructions to insert the companion CD-ROM included in this package. Monitor drivers (.inf and .icm files) will be installed automatically. Q4: How do I adjust the resolution? • Ans.: Your video card/graphic driver and monitor together determine the available resolutions.
7. Troubleshooting & FAQs Philips sales representative for more information. Q10: Are Philips LCD monitors Plugand- Play? 1440. For best display, please use this resolution. Q13: How to unlock/lock my hot key? Ans.: P lease press for 10 seconds to unlock/lock the hot key, by doing so, your monitor pops out “Attention” to show the unlock/ lock status as shown below illustrators. Ans.: Y es, the monitors are Plug-andPlay compatible with Windows 10/8.1/8/7, Mac OSX.
2020 © TOP Victory Investment Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
