IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Philips Consumer Electronics Company** Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
FIRE AND SHOCK HAZARD 1. Be sure all components are positioned in such a way as to avoid the possibility of adjacent component shorts. This is especially important on those chassis which are transported to and from the service shop. 2. Never release a repaired unit unless all protective devices such as insulators, barriers, covers, strain reliefs, and other hardware have been installed in accordance with the original design. 3.
LEAKAGE CURRENT COLD CHECK 1. Unplug the ac line cord and connect a jumper between the two prongs of the plug. 2. Turn on the power switch. 3. Measure the resistance value between the jumpered ac plug and all exposed cabinet parts of the receiver, such as screw heads, antennas, and control shafts. When the exposed metallic part has a return path to the chassis, the reading should be between 1 megohm and 5.2 megohms.
TV SAFETY NOTES SAFETY CHECKS After the original service problem has been corrected, a complete safety check should be made. Be sure to check over the entire set, not just the areas where you have worked. Some previous servicer may have left an unsafe condition, which could be unknowingly passed on to your customer.
5. When troubleshooting and making test measurements in a receiver with a problem of excessive high voltage, reduce the line voltage by means of a Variac to bring the HV into acceptable limits while troubleshooting. Do not operate the chassis longer than necessary to locate the cause of the excessive HV. 6. New picture tubes are specifically designed to withstand higher operating voltages without creating undesirable X-radiation.
PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) Some semiconductor solid state devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices, Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD). 1.
PRACTICAL SERVICE PRECAUTIONS IT MAKES SENSE TO AVOID EXPOSURE TO ELECTRICAL SHOCK. While some sources are expected to have a possible dangerous impact, others of quite high potential are of limited current and are sometimes held in less regard. ALWAYS RESPECT VOLTAGES. While some may not be dangerous in themselves, they can cause unexpected reactions – reactions that are best avoided. Before reaching into the powered color TV set, it is best to test the high voltage insulation.
Technical Specifications, Connections, and Chassis Overview Note: Described specifications are valid for the whole product range. Note: Figures below can deviate slightly from the actual situation, due to different set executions. Technical Specifications Reception Feature Data Tuning system : PLL Color systems : NTSC Sound systems : BTSC Channel selections : 181, full cable IF picture carrier : 45.75 MHz Aerial input : 75 Ohm, F-type A/V Connections : NTSC M (3.58 - 4.
Feature Data Mains voltage range : 90 - 140 V_ac Mains frequency : 60 Hz Ambient conditions: Feature Data Temperature range : +5 to +45 deg. C Maximum humidity : 90 % R.H.
Connections Note: The following connector color abbreviations are used (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= Grey, Rd= Red, Wh= White, Ye= Yellow.
Audio / Video In Connector Kind Value Symbol Ye Video (CVBS) 1 V_pp / 75 ohm H Wh Audio - L 0.2 V_rms / 10 kohm kq Rd Audio - R 0.
Monitor Out Connector Kind Value Symbol Ye Video (CVBS) 1 V_pp / 75 ohm kq Wh Audio - L 0.5 V_rms / 1 kohm kq Rd Audio - R 0.5 V_rms / 1 kohm kq Connector Kind Value Symbol Bu U 0.7 V_pp / 75 ohm jq Rd V 0.7 V_pp / 75 ohm jq Gn Y 0.7 V_pp / 75 ohm jq Connector Kind Value Symbol Ye Video (CVBS) 1 V_pp / 75 ohm jq Wh Audio - L 0.5 V_rms / 10 kohm jq Rd Audio - R 0.
AV2 In Connector Kind Value Symbol Ye Video (CVBS) 1 V_pp / 75 ohm jq Wh Audio - L 0.5 V_rms / 10 kohm jq Rd Audio - R 0.5 V_rms / 10 kohm jq AV2 In (SVHS) Connector Kind Value Symbol 1 Ground GND H 2 Ground GND H 3 Y 1 V_pp / 75 ohm jq 4 C 0.
Mechanical Instructions Index of this chapter: 1. Set Disassembly 2. Service Position 3. Assembly/Panel Removal 4. Set Re-assembly Note: Figures below can deviate slightly from the actual situation, due to different set executions. Set Disassembly Warning: Be sure to disconnect the AC power from the set before opening it. Rear Cover 1. Remove all fixation screws of the rear cover (do not forget the screws that hold the rear connection panel). 2. Pull the rear cover backwards to remove it.
Figure: Service position Mono Carrier
1. Disconnect the degaussing coil [1]. 2. Release the two fixation clamps (at the mid left and mid right side of the bracket), and remove the bracket from the bottom tray, by pulling it backwards [2]. 3. Turn the chassis tray 90 degrees counter clockwise. 4. Move the panel bracket somewhat to the left and flip it 90 degrees [3], with the components towards the CRT. 5. Turn the panel bracket with the rear I/O toward the CRT. 6.
1. Remove the complete module from the bottom plate, by pulling the two fixation clamps upward [1], while sliding the module away from the CRT [2]. Note: these clamps are difficult to access. 2. Release the two fixation clamps [3] at the side of the bracket, and lift the panel out of the bracket (it hinges at one side). Side AV Assembly/Panel Removal Figure: Side AV assembly/panel removal 1. Remove the two fixation screws, and remove the complete Side AV assembly. 2.
LTI/CTI Interface Panel Removal Remove the LTI/CTI Interface panel from the Mono Carrier, by disconnecting it from connector 1212. Top Control Assembly/Panel Removal 1. Remove the two fixation screws. 2. Push the assembly a little bit upwards, and then pull it backwards to release it from the front hinge. 3. Lift the panel from its bracket, while releasing the two fixation clamps. The panel hinges on the other side. Linearity Assembly/Panel Removal Figure: Linearity assembly/panel removal 1.
Set Re-assembly To re-assemble the whole set, do all processes in reverse order. Note: before you mount the rear cover, perform the following checks: 1. Check whether the AC power cord is mounted correctly in its guiding brackets. 2.
Service Modes, Error Codes, and Fault Finding Index of this chapter: 1. Test Points 2. Service Modes 3. Problems and Solving Tips (related to CSM) 4. ComPair 5. Error Codes 6. The Blinking LED Procedure 7. Protections 8. Repair Tips Test Points This chassis is equipped with test points in the service printing. In the schematics test points are identified with a rectangle box around Fxxx or Ixxx.
Table: Test point overview Test point Circuit Diagr.
Service Modes Service Default mode (SDM) and Service Alignment Mode (SAM) offers several features for the service technician, while the Customer Service Mode (CSM) is used for communication between the call center and the customer. This chassis also offers the option of using ComPair, a hardware interface between a computer and the TV chassis. It offers the abilities of structured troubleshooting, error code reading, and software version readout for all chassis.
Table: Software cluster overview SW Cluster SW name UOC Type 12 NC Features 9352 L4LUS1 L04US1_x.y TDA12000 753 CC+BTSC 88557 9352 L4LUS1 L04US1_x.y TDA12001 753 CC+BTSC+CMB+DW 89557 9352 L4LUS1 L04US1_x.
Service Default Mode (SDM) Purpose • To create a predefined setting for measurements to be made. • To override software protections. • To start the blinking LED procedure. Specifications • Tuning frequency: 61.25 MHz (channel 3). • Color system: NTSC M. • All picture settings at 50% (brightness, color contrast, hue). • Bass, treble and balance at 50 %; volume at 25 %. • All service-unfriendly modes (if present) are disabled. The service unfriendly modes are: § Timer / Sleep timer.
How to enter To enter SDM, use one of the following methods: • Press the following key sequence on the remote control transmitter: “062596” directly followed by the MENU button (do not allow the display to time out between entries while keying the sequence). • Short jumper wires 9252 and 9275 on the family board (see Fig. 8-1) and apply AC power. Then press the power button (remove the short after start-up). Caution: Entering SDM by shorting wires 9252 and 9275 will override the +8Vprotection.
How to navigate Use one of the following methods: • When you press the MENU button on the remote control, the set will switch on the normal user menu in the SDM mode. • On the TV, press and hold the VOLUME DOWN and press the CHANNEL DOWN for a few seconds, to switch from SDM to SAM and reverse. How to exit Switch the set to STANDBY by pressing the POWER button on the remote control transmitter or the television set. If you turn the television set off by removing the AC power (i.e.
Specifications • Operation hours counter (maximum five digits displayed). • Software version, Error codes, and Option settings display. • Error buffer clearing. • Option settings. • AKB switching. • Software alignments (Tuner, White Tone, Geometry & Audio). • NVM Editor. • ComPair Mode switching.
Figure: SAM menu Menu explanation 1. LLLLL. This represents the run timer. The run timer counts normal operation hours, but does not count standby hours. 2. AAABCD-X.Y. This is the software identification of the main microprocessor: § A = the project name (L04). § B = the region: E= Europe, A= Asia Pacific, U= NAFTA, L= LATAM. § C = the software diversity: § Europe: T= 1 page TXT, F= Full TXT, V= Voice control. § LATAM and NAFTA: N= Stereo non-dBx, S= Stereo dBx.
3. SAM. Indication of the Service Alignment Mode. 4. Error Buffer. Shows all errors detected since the last time the buffer was erased. Five errors possible. 5. Option Bytes. Used to set the option bytes. See “Options” in the Alignments section for a detailed description. Seven codes are possible. 6. Clear. Erases the contents of the error buffer. Select the CLEAR menu item and press the MENU RIGHT key. The content of the error buffer is cleared. 7. Options. Used to set the option bits.
How to navigate • In SAM, select menu items with the MENU UP/DOWN keys on the remote control transmitter. The selected item will be highlighted. When not all menu items fit on the screen, use the MENU UP/DOWN keys to display the next / previous menu items. • • With the MENU LEFT/RIGHT keys, it is possible to: § Activate the selected menu item. § Change the value of the selected menu item. § Activate the selected submenu.
Customer Service Mode (CSM) Purpose The Customer Service Mode shows error codes and information on the TV's operation settings. The call center can instruct the customer (by telephone) to enter CSM in order to identify the status of the set. This helps the call center to diagnose problems and failures in the TV set before making a service call. The CSM is a read-only mode; therefore, modifications are not possible in this mode.
Menu explanation 1. Indication of the decimal value of the operation hours counter, Software identification of the main microprocessor (see 'Service Default or Alignment Mode' for an explanation), and the service mode (CSM= Customer Service Mode). 2. Displays the last five errors detected in the error code buffer. 3. Displays the option bytes. 4. Displays the type number version of the set. 5. Reserved item for P3C call centers (AKBS stands for Advanced Knowledge Base System). 6.
Problems and Solving Tips Related to CSM Picture Problems Note: The problems described below are all related to the TV settings. The procedures used to change the value (or status) of the different settings are described. Picture too dark or too bright If: • The picture improves when you have press the AUTO PICTURE button on the remote control transmitter, or • The picture improves when you enter the Customer Service Mode, Then: 1.
White line around picture elements and text If: The picture improves after you have pressed the AUTO PICTURE button on the remote control transmitter, Then: 1. Press the AUTO PICTURE button on the remote control transmitter repeatedly (if necessary) to choose PERSONAL picture mode. 2. Press the MENU button on the remote control transmitter. This brings up the normal user menu. 3. In the normal user menu, use the MENU UP/DOWN keys to highlight the PICTURE sub menu. 4.
Black and white picture If: • The picture improves after you have pressed the AUTO PICTURE button on the remote control transmitter, Then: 1. Press the AUTO PICTURE button on the remote control transmitter repeatedly (if necessary) to choose PERSONAL picture mode. 2. Press the MENU button on the remote control transmitter. This brings up the normal user menu. 3. In the normal user menu, use the MENU UP/DOWN keys to highlight the PICTURE sub menu. 4.
Then: 1. Press the AUTO PICTURE button on the remote control transmitter repeatedly (if necessary) to choose PERSONAL picture mode. 2. Press the MENU button on the remote control transmitter. This brings up the normal user menu. 3. In the normal user menu, use the MENU UP/DOWN keys to highlight the PICTURE sub menu. 4. Press the MENU LEFT/RIGHT keys to enter the PICTURE sub menu. 5. Use the MENU UP/DOWN keys to select PICTURE. 6. Press the MENU LEFT key to decrease the PICTURE value. 7.
Specifications ComPair consists of a Windows based faultfinding program and an interface box between PC and the (defective) product. The ComPair interface box is connected to the PC via a serial or RS232 cable. In this chassis, the ComPair interface box and the TV communicate via a bi-directional service cable via the service connector. The ComPair faultfinding program is able to determine the problem of the defective television.
Beside fault finding, ComPair provides some additional features like: • Up- or downloading of pre-sets. • Managing of pre-set lists. • Emulation of the Dealer Service Tool (DST). • If both ComPair and SearchMan (Electronic Service Manual) are installed, all the schematics and the PWBs of the set are available by clicking on the appropriate hyperlink. Example: Measure the DC-voltage on capacitor C2568 (Schematic/Panel) at the Mono-carrier .
7. Plug the mains adapter in a mains outlet, and switch the interface “on”. The green and red LEDs light up together. The red LED extinguishes after approx. 1 second while the green LED remains lit. 8. Start the ComPair program and read the “Introduction” chapter. Figure: ComPair Interface connection How To Order ComPair order codes: • ComPair Software: ST4191. • ComPair Interface Box: 4822 727 21631. • AC Adapter: T405-ND. • ComPair Quick Start Guide: ST4190.
Error Codes The error code buffer contains all errors detected since the last time the buffer was erased. The buffer is written from left to right. When an error occurs that is not yet in the error code buffer, it is displayed at the left side and all other errors shift one position to the right. How To Read The Error Buffer You can read the error buffer in 3 ways: • On screen via the SAM (if you have a picture).
§ Make sure the menu item CLEAR is highlighted. Use the MENU UP/DOWN buttons, if necessary. § Press the MENU RIGHT button to clear the error buffer. The text on the right side of the “CLEAR” line will change from “CLEAR?” to “CLEARED” • If the contents of the error buffer have not changed for 50 hours, the error buffer resets automatically. Note: If you exit SAM by disconnecting the AC power from the television set, the error buffer is not reset.
Error Device Error description Check item Diagram 3466, 3 Not applicable Vertical guard 7451, protection 7452, A2 7453, 7454 4 Tuner I2C error while 1000, communicating with 5010, (PIP F2 2nd tuner Module) 5 Not applicable +5v protection 6 I2C bus 7 Not applicable - - - 8 Not applicable - - - General I2C error I2C error while 9 24C16 communicating with the EEPROM 7604, 7605 A5 7200, 3207, 3214 7601, 3604, 3605 A4 A5 I2C error while 10 Tuner communicating with 1000,
Error Device Error description Check item Diagram I2C error while 15 TDA9178T/N1 communicating with 7610 H 7201 F2 LTI module I2C error while 16 TDA9887 communicating with PIP_Demodulator 17 Not applicable - - - 18 Not applicable - - - 7200 A4 7200 A4 I2C error while 19 TDA1200x communicating with SSD stereo sound decoder I2C error while 20 TDA1200x communicating with video cosmic in Hercules IC
The Blinking LED Procedure Using this procedure, you can make the contents of the error buffer visible via the front LED. This is especially useful when there is no picture. When the SDM is entered, the front LED will blink the contents of the error-buffer: • When all the error-codes are displayed, the sequence finishes with a LED blink of 1.5 seconds, • The sequence starts again.
To get a quick diagnosis the chassis has three service modes implemented: • The Customer Service Mode (CSM). • The Service Default Mode (SDM). • The Service Alignment Mode (SAM). For a detailed mode description, see the relevant sections. Fault Finding and Repair Tips Notes: • It is assumed that the components are mounted correctly with correct values and no bad solder joints. • Before any fault finding actions, check if the correct options are set.
Address Value (dec) (hex) HS (Horizontal shift) 21 1A HP (Horizontal parallelogram) 22 1F HB (Horizontal Bow) 23 1F UCP (EW upper corner parabola) 24 1E LCP (EW lower corner parabola) 25 28 TC (EW trapezium) 26 1A VS (Vertical slope) 27 25 VA (Vertical amplitude) 28 1E SC (S-Correction) 29 19 VSH (Vertical Shift) 30 1A VX (Vertical Zoom) 31 19 VSL (Vertical scroll) 32 20 VL (Vertical linearity) 33 20 BLOR (Black level Offset - Red) 34 1D BLOG (Black level Offset
Address Value (dec) (hex) 60 Hz Vertical amplitude 42 40 YD & CL 43 58 RGB amplitude for full teletext mode 46 8 NVM_TABLE_VERSION 60 19 OPTION_TABLE_VERSION 61 8 CVI_BLOR 62 15 CVI_BLOG 63 0F TXT Brightness 64 17 V60 offset (60Hz Vertical Amplitude) 66 FE FOAB, CHSE 139 3 SPR, WS 140 0 VMA, SVM 141 32 NVM_SOC_SMD 142 3 CCC_Preset_Gain_Red 143 1F CCC_Preset_Gain_Green 144 1F CCC_Preset_Gain_Blue 145 1F NVM_FMWS 149 3 NVM_ASD_SC1_THR 150 10 NVM_CRYSTA
Address Value (dec) (hex) Last Hue (VID PP others) 268 32 Last Colour Temperature (VID PP others) 269 1 White-D Cool Red 294 FD White-D Cool Blue 296 5 White-D Normal Red 297 1A White-D Normal Green 298 20 White-D Normal Blue 299 1B White-D Warm Red 300 2 White-D Warm Blue 302 FA Last Volume 343 14 Last Balance 344 32 Last Treble (AUD PP others) 345 32 Last Bass (AUD PP others) 346 32 NAFTA Region
Power Supply Set Not Working Figure: Fault finding tree “Set not working”
Set Does Not Start Up Figure: Fault finding tree “Set does not start up”
Deflection One Thin Vertical Line Quick check: • Set in protection mode. • LED blinking with error “3”.
One Thin Horizontal Line Quick check: • Set in protection mode. • LED blinking with error “2”.
Blank Screen Figure: Fault finding tree “Blank screen”
Source Selection Set is not able to go into AV or any missing AV is encountered E.g. AV1 is available but not able to enter to AV1: Check if the option setting is correct. Set is able to go to AV, but no audio is heard. 1. Check that continuity of signal is there from the SCART/Cinch input to the input of the Hercules. 2. If continuity is there and still no audio, check that option settings are correct. 3.
6. If Tuner IF is present and yet still no picture in RF mode, go to Video Processing troubleshooting section.
Picture Ok, No Sound Figure: Fault finding tree “Picture ok, no sound”
Unable To Perform Tuning Figure: Fault finding tree “Unable to perform tuning”
Controller Below are some guidelines for troubleshooting of the Micro Controller function. Normally Micro Controller should be checked when there is a problem of startup. 1. Check that both +3.3 V_dc and +1.8 V_dc are present. 2. Check that crystal oscillator is working. 3. Check that Power Good signal is at “high” logic, normal operation. 4. Check that Hercules is not in standby mode. Pin 15 of Hercules should be 0 V_dc. 5. Make sure H-drive pulse is there. This can be checked at resistor R3239.
4. If signal is not available, try checking the BRIGHTNESS and/or CONTRAST control, and make sure it is not at zero. 5. If still with the correct settings and no video is available, proceed to the CRT/RGB amplifier diagram. For sets with TDA9178, follow steps below: 1. Put Option Byte 2 bit 4 to “0”; if video signal is not available, then check fault finding section “Controller”, Section “Source Selection”, and steps above. 2.
Audio Processing No Sound Figure: Fault finding tree “No sound”
No RF audio for QSS/Inter-Carrier stereo sets. 1. Check pin 99 and 100 for SIF signal (for QSS) or pin 104 and 105 for video with SIF (for Inter-Carrier) 2. If signal is not present, check for the QSS/FMI bit settings. Check also the NVM data. 3. If signals are present and still no audio, check the audio supply voltage +8V are present. 4. If still no audio signal at Hercules output, Hercules is faulty. No AV audio. 1. Check troubleshooting methods in section “Source Selection”. 2.
Alignments Index of this chapter: 1. General Alignment Conditions 2. Hardware Alignments 3. Software Alignments and Settings Note: • The Service Default Mode (SDM) and Service Alignment Mode (SAM) are described in chapter 5 “Service Modes, ...”. • Menu navigation is done with the CURSOR UP, DOWN, LEFT, or RIGHT keys of the remote control transmitter.
Hardware Alignments Figure: Top view family board
Vg2 Adjustment 1. Activate the SAM. 2. Go to the WHITE TONE sub menu. 3. Set the values of NORMAL RED, GREEN and BLUE to “32”. 4. Go, via the MENU key, to the normal user menu and set 5. SATURATION/COLOR to “0”. 6. CONTRAST to “0”. 7. BRIGHTNESS to minimum (OSD just visible). 8. Return to the SAM via the MENU key. 9. Connect the RF output of a pattern generator to the antenna input. Test pattern is a 'black' picture (blank screen on CRT without any OSD info) with a signal strength of 1 V_pp. 10.
Figure: V_cutoff waveform Focusing 1. Tune the set to a circle or crosshatch test pattern (use an external video pattern generator). 2. Choose picture mode NATURAL (or MOVIES) with the SMART PICTURE button on the remote control transmitter. 3. Adjust the FOCUS potentiometer (see figure “Top view family board”) until the vertical lines at 2/3 from east and west, at the height of the centerline, are of minimum width without visible haze.
Software Alignments and Settings Figure: Service Mode overview
Enter the Service Alignment Mode (see also chapter 5 “Service Modes, ....”). To enter SAM, use one of the following methods: • Press the following key sequence on the remote control transmitter: “062596' directly followed by the OSD/STATUS button (do not allow the display to time out between entries while keying the sequence). • Or via ComPair. The SAM menu will now appear on the screen.
How to calculate the value of an Option Byte Calculate an Option Byte value (OP1 .. OP7) in the following way: • Check the status of the single option bits (OB): are they enabled (1) or disabled (0). • When an option bit is enabled (1) it represents a certain value (see column “Bit value” in table below). When an option bit is disabled, its value is 0. • The total value of an Option Byte (decimal) is formed by the sum of its eight option bits. The factory values are printed on a sticker on the CRT.
Table: Option code overview per model (OP1 - OP4) 25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_1 (OP1) 7 Philips Tuner 0 0 0 0 0 0 0 0 6 FM Radio 0 0 0 0 0 0 0 0 5 LNA 0 0 0 0 0 0 0 0 4 ATS(EU) 0 0 0 0 0 0 0 0 3 ACI 0 0 0 0 0 0 0 0 2 UK PNP 0 0 0 0 0 0 0 0 1 Virgin Mode 0 0 0 0 0 0 0 0 0 China 0 0 0 0 0 0 0 0 Decimal 0 0 0 0 0 0 0 0 -
25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_2 (OP2) 7 SC 0 0 0 0 0 0 0 0 6 Green_UI 0 0 1 0 0 0 0 0 5 Channel Naming 0 0 0 0 0 0 0 0 4 LTI 0 1 0 0 0 1 0 0 3 Tilt 0 1 0 0 0 1 0 0 2 Fine Tuning 0 0 0 0 0 0 0 0 1 PIP Philips Tuner 0 0 0 0 0 0 0 0 0 Hue 1 1 1 1 1 1 1 1 Decimal 1 25 65 1 1 25 1 1 -
25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_3 (OP3) 7 EW Function 0 0 0 0 0 0 0 0 6 2 Tuner PIP 0 0 0 0 0 0 0 0 5 PIP_Splitter 0 0 0 0 0 0 0 0 4 Splitter 0 0 0 0 0 0 0 0 3 Virtual Dolby 0 1 0 0 0 1 0 0 2 Wide Screen 0 1 0 0 0 1 0 0 1 WSSB(EU) 0 0 0 0 0 0 0 0 0 Eco_Subwoofer 0 0 0 0 0 0 0 0 Decimal 0 12 0 0 0 12 0 0 -
25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_4 (OP4) 7 - 0 0 0 0 0 0 0 0 6 - 0 0 0 0 0 0 0 0 5 Ultra Bass 1 1 0 1 1 1 1 1 4 Delta Volume 0 0 0 0 0 0 0 0 3 - 0 0 0 0 0 0 0 0 2 Volume Limiter 0 0 0 0 0 0 0 0 1 - 0 0 0 0 0 0 0 0 0 Stereo_Nicam_2CS 0 0 0 0 0 0 0 0 Decimal 32 0 32 32 32 32 32 32
Table: Option code overview per model (OP1 - OP4) (continued) 29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_1 (OP1) 7 Philips Tuner 0 0 0 0 0 0 0 0 6 FM Radio 0 0 0 0 0 0 0 0 5 LNA 0 0 0 0 0 0 0 0 4 ATS(EU) 0 0 0 0 0 0 0 0 3 ACI 0 0 0 0 0 0 0 0 2 UK PNP 0 0 0 0 0 0 0 0 1 Virgin Mode 0 0 0 0 0 0 0 0 0 China 0 0 0 0 0 0 0 0 Decimal 0 0 0 0 0 0 0 0 -
29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_2 (OP2) 7 SC 0 0 0 0 0 0 0 0 6 Green_UI 0 0 0 1 0 0 0 0 5 Channel Naming 0 0 0 0 0 0 0 0 4 LTI 1 1 1 0 0 0 1 0 3 Tilt 0 0 1 1 0 1 1 0 2 Fine Tuning 0 0 0 0 0 0 0 0 1 PIP Philips Tuner 0 0 0 0 0 0 0 0 0 Hue 1 1 1 1 1 1 1 1 Decimal 17 17 25 73 1 9 25 1 -
29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_3 (OP3) 7 EW Function 0 0 0 0 0 0 0 0 6 2 Tuner PIP 0 0 0 0 0 0 0 0 5 PIP_Splitter 0 0 0 0 0 0 0 0 4 Splitter 0 0 0 0 0 0 0 0 3 Virtual Dolby 1 1 1 0 0 0 1 0 2 Wide Screen 0 0 1 0 0 0 1 0 1 WSSB(EU) 0 0 0 0 0 0 0 0 0 Eco_Subwoofer 0 0 0 0 0 0 0 0 Decimal 8 8 12 0 0 0 12 0 -
29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_4 (OP4) 7 - 0 0 0 0 0 0 0 0 6 - 0 0 0 0 0 0 0 0 5 Ultra Bass 1 1 1 0 1 1 1 1 4 Delta Volume 0 0 0 0 0 0 0 0 3 - 0 0 0 0 0 0 0 0 2 Volume Limiter 0 0 0 0 0 0 0 0 1 - 0 0 0 0 0 0 0 0 0 Stereo_Nicam_2CS 0 0 0 0 0 0 0 0 Decimal 32 32 0 32 32 32 32 32
Table: Option code overview per model (OP5 - OP7) 25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_5 (OP5) 7 AV1 1 1 1 1 1 1 1 1 6 AV2 1 1 1 1 1 1 1 1 5 AV3 1 1 1 1 1 1 1 1 4 CVI 1 1 1 1 1 1 1 1 3 SVHS2 1 1 1 1 1 1 1 1 2 SVHS3 0 0 0 0 0 0 0 0 1 Hotel Mode 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 Decimal 248 248 248 248 248 248 248 248 -
25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_6 (OP6) 7 Personal Zapping 1 1 0 1 1 1 1 1 6 - 0 0 0 0 0 0 0 0 5 FM Trap 0 0 0 0 0 0 0 0 4 Combfilter 0 1 0 0 0 1 0 0 3 Active Control 1 1 0 0 1 1 1 1 2 Video Text 0 0 0 0 0 0 0 0 1 Light Sensor 0 1 0 0 0 1 0 0 0 Dual Text 0 0 0 0 0 0 0 0 Decimal 136 154 0 128 136 154 136 136 -
25PT6341/85 26PW6341/37 27MS6341/37 27PT5441/37 27PT6441/37 28PW6341/85 29PT6441/44 29PT6441/85 Bit Byte_7 (OP7) 7 Time Win1 0 0 0 0 0 0 0 0 6 - 0 0 0 0 0 0 0 0 5 - 0 0 0 0 0 0 0 0 4 - 0 0 0 0 0 0 0 0 3 - 0 0 0 0 0 0 0 0 2 - 0 0 0 0 0 0 0 0 1 - 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 Decimal 0 0 0 0 0 0 0 0
Table: Option code overview per model (OP5 - OP7) (continued) 29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_5 (OP5) 7 AV1 1 1 1 1 1 1 1 1 6 AV2 1 1 1 1 1 1 1 1 5 AV3 1 1 1 1 1 1 1 1 4 CVI 1 1 1 1 1 1 1 1 3 SVHS2 1 1 1 1 1 1 1 1 2 SVHS3 0 0 0 0 0 0 0 0 1 Hotel Mode 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 Decimal 248 248 248 248 248 248 248 248 -
29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_6 (OP6) 7 Personal Zapping 1 1 1 0 1 1 1 1 6 - 0 0 0 0 0 0 0 0 5 FM Trap 0 0 0 0 0 0 0 0 4 Combfilter 1 1 1 0 0 1 1 0 3 Active Control 1 1 1 0 0 1 1 0 2 Video Text 0 0 0 0 0 0 0 0 1 Light Sensor 1 1 1 0 0 0 1 0 0 Dual Text 0 0 0 0 0 0 0 0 Decimal 154 154 154 0 128 152 154 128 -
29PT6541/44 29PT6541/85 30PW6341/37 32MS6341/37 32PT5441/37 32PT6441/37 32PW6341/85 33PT5441/85 Bit Byte_7 (OP7) 7 Time Win1 0 0 0 0 0 0 0 0 6 - 0 0 0 0 0 0 0 0 5 - 0 0 0 0 0 0 0 0 4 - 0 0 0 0 0 0 0 0 3 - 0 0 0 0 0 0 0 0 2 - 0 0 0 0 0 0 0 0 1 - 0 0 0 0 0 0 0 0 0 - 0 0 0 0 0 0 0 0 Decimal 0 0 0 0 0 0 0 0
Option Bit Assignment Following are the option bit assignments for all software clusters.
• • • Option Byte 4 (OP4) § OB47: Reserved (value= 0) § OB46: Reserved (value= 0) § OB45: ULTRA BASS § OB44: DELTA VOLUME § OB43: Reserved (value= 0) § OB42: VOLUME LIMITER § OB41: Reserved (value= 0) § OB40: STEREO NICAM 2CS Option Byte 5 (OP5) § OB57: AV1 § OB56: AV2 § OB55: AV3 § OB54: CVI § OB53: SVHS2 § OB52: SVHS3 § OB51: HOTEL MODE § OB50: Reserved (value= 0) Option Byte 6 (OP6) § OB67: PERSONAL ZAPPING § OB66: Reserved (value= 0) § OB65: FM TRAP § OB64: COMB
• Option Byte 7 (OP7) § OB77: TIME WIN1 § OB76: Reserved (value= 0) § OB75: Reserved (value= 0) § OB74: Reserved (value= 0) § OB73: Reserved (value= 0) § OB72: Reserved (value= 0) § OB71: Reserved (value= 0) § OB70: Reserved (value= 0) Option bit definition Option Byte 1 (OP1) • • • • OB17: PHILIPS TUNER § 0 : ALPS / MASCO compatible tuner is in use. § 1 : Philips compatible tuner is in use. OB16: FM RADIO § 0 : FM radio feature is disabled or not applicable.
• OB12: UK PNP § 0 : UK's default Plug and Play setting is not available or not applicable. § 1 : UK's default Plug and Play setting is available. When UK PNP and VIRGIN MODE are set to “1” at the initial setup and after exiting from menu, VIRGIN MODE will be set automatically to “0” while UK PNP remains “1”. • OB11: VIRGIN MODE § 0 : Virgin mode is disabled or not applicable. § 1 : Virgin mode is enabled.
• • • • • OB24: LTI § 0 : Luminance Transient Improvement (LTI) is disabled or not applicable. § 1 : LTI is enabled. OB23: TILT § 0 : Rotate Picture is disabled or not applicable. § 1 : Rotate Picture is enabled. OB22: FINE TUNING § 0 : Fine Tuning for Channel Offset is disabled or not applicable. § 1 : Fine Tuning for Channel Offset is enabled. OB21: PIP PHILIPS TUNER § 0 : ALPS / MASCO compatible tuner is in use for PIP module. § 1 : Philips compatible tuner is in use for PIP module.
• OB35: PIP SPLITTER § 0 : Normal Tuner in PIP § 1 : Splitter in PIP § Note: Only for EU/AP region. For PIP sets and build in with Splitter in PIP tuner. • • • • • OB34: SPLITTER § 0 : Normal Tuner for main chassis § 1 : Splitter Tuner for main chassis § Note: Only for EU/AP region. OB33: VIRTUAL DOLBY § 0 : Virtual Dolby is not applicable. § 1 : Virtual Dolby is applicable. OB32: WIDE SCREEN § 0 : Software is used for 4:3 sets or not applicable.
• • • OB45: ULTRA BASS § 0 : Ultra Bass is disabled or not applicable. § 1 : Ultra Bass is enabled. § Default setting is “0”. OB44: DELTA VOLUME § 0 : Delta Volume Level is disabled or not applicable. § 1 : Delta Volume Level is enabled. OB43: Reserved § • • OB42: VOLUME LIMITER § 0 : Volume Limiter Level is disabled or not applicable. § 1 : Toggle Volume Limiter Level is enabled. OB41: Reserved § • Default setting is “0”. Default setting is “0”.
• • • • • • OB55: AV3 § 0 : Side/Front AV3 source is not present. § 1 : Side/Front AV3 source is present. OB54: CVI § 0 : CVI source is not available. § 1 : CVI source is available. OB53: SVHS2 § 0 : SVHS2 source is not available. § 1 : SVHS2 source is available. § Note : This option bit is not applicable for EU. OB52: SVHS3 § 0 : SVHS3 source is not available. § 1 : SVHS3 source is available. § Note : This option bit is not applicable for EU.
• • • • • • OB65: FM TRAP § 0 : FM Trap is not present. § 1 : FM Trap is present. § Note: Only for LATAM region. OB64: COMBFILTER § 0 : 3D-combfilter is not present. § 1 : 3D-combfilter is present. OB63: ACTIVE CONTROL § 0 : Active Control feature is disabled or not applicable. § 1 : Active Control feature is enabled. OB62: VIDEO TEXT § 0 : Video Text (DW with TXT) is disabled or not applicable. § 1 : Video Text (DW with TXT) is enabled. § Note: For EU only.
• OB75: Reserved § • OB74: Reserved § • Default setting is “0”. OB71 Reserved § • Default setting is “0”. OB72 Reserved § • Default setting is “0”. OB73: Reserved § • Default setting is “0”. Default setting is “0”. OB70: Reserved § Default setting is “0”.
Bit Byte_1 (Pin Usage) 7 Not Used 0 0 6 WideScreen 0 0 5 Rotation 0 1 4 QSS 0 0 3 Uir Msg 0 0 2 SPI I2C 1 1 1 Not Used 0 0 0 Not Used 0 0 Decimal 4 36 Bit Byte_2 (Devices) 7 SCAVEM 1 1 6 Comb Filter 0 1 5 EW 1 1 4 OSD FRONT 0 0 3 Radio 0 0 2 LNA 0 0 1 Tuner 1 1 0 "None-00, Philips-01, Alps-10" 0 0 Decimal 162 226
Bit Byte_3 (Devices) 7 Not Used 0 0 6 Soft Clipper 0 0 5 Not Used 0 0 4 Not Used 0 0 3 SmartPort 1 1 2 Active-Off LED 0 0 1 WSL 0 0 0 "None-00, 4136-01, 34836-10" 1 1 Decimal 9 9 Bit "Byte_4 (AV, Tuning)" 7 Not Used 0 0 6 AV3YC 0 0 5 CVI 1 1 4 AV2YC 1 1 3 AV3 1 1 2 AV2 1 1 1 AV1 0 0 0 RGB 0 0 Decimal 60 60
Bit Byte_5 (Feature) 7 ITV Ring 0 0 6 Protection 1 1 5 WatchDog 1 1 4 No Ident Standby 1 1 3 Buzzer Type 0 0 2 "None=00, Internal=01, External=10" 1 1 1 Clock Type 0 0 0 "None-00, OSD-01, LED-10" 1 1 Decimal 117 117 Bit Byte_6 (Power) 7 Not Used 0 0 6 Not Used 0 0 5 Not Used 0 0 4 Not Used 0 0 3 Not Used 0 0 2 Not Used 0 0 1 Card POR 0 0 0 Not Used 0 0 Decimal 0 0
Tuner Note: Described alignments are only necessary when the NVM (item 7601) is replaced. IF PLL This adjustment is auto-aligned. Therefore, no action is required. AGC (AGC take over point) 1. Set the external pattern generator to a color bar video signal and connect the RF output to aerial input. Set amplitude to 10 mV and set frequency to 61.25 MHz (channel 3). 2. Connect a DC multimeter to pin 1 of the tuner (item 1000 on the main panel). 3. Activate the SAM. 4. Go to the TUNER sub menu. 5.
White Tone In the WHITE TONE sub menu, the values of the black cut off level can be adjusted. Normally, no alignment is needed, and you can use the given default values. The color temperature mode (NORMAL, COOL and WARM) and the color (R, G, and B) can be selected with the UP/DOWN RIGHT/LEFT cursor keys. The value can be changed with the LEFT/RIGHT cursor keys. First, select the values for the NORMAL color temperature. Then select the values for the COOL and WARM mode.
Figure: Geometry alignments
1. Connect an external video pattern generator to the aerial input of the TV-set and input a crosshatch test pattern. Set the generator amplitude to at least 1 mV and set frequency to 61.25 MHz (channel 3). 2. Set 'Smart Picture' to NATURAL (or MOVIES). 3. Activate the SAM menu (see chapter 5 “Service Modes, ...”). 4. Go to the GEOMETRY sub menu. 5. Choose HORIZONTAL or VERTICAL alignment Now the following alignments can be performed: Horizontal • Horizontal Parallelogram (HP).
Vertical • Service blanking (SBL). Switch the blanking of the lower half of the screen “on” or “off” (to be used in combination with the vertical slope alignment). • Vertical Shift (VSH). Align the vertical centering so that the test pattern is located vertically in the middle. Repeat the 'vertical amplitude' alignment if necessary. • Vertical slope (VS). Align the vertical center of the picture to the vertical center of the CRT. This is the first of the vertical alignments to perform.
Alignment Default values UCP (EW upper corner parabola) 30 LCP (EW lower corner parabola) 40 VSH (Vertical Shift) 26 VS (Vertical slope) 37 VAM (Vertical amplitude) 30 VSC (Vertical S-Correction) 25 Audio No alignments are needed for the audio sub menu. Use the given default values. QSS (Quasi Split Sound) • For NICAM/2CS sound system (EU/AP, except for AP-NTSC), set to “On”. • For AV-Stereo sound system (sets without NICAM), set to “On”.
Circuit Descriptions, List of Abbreviations, and IC Data Sheets Index of this chapter: 1. Introduction 2. Power Supply 3. Deflection 4. Control 5. Tuner and IF 6. Source Selection 7. Audio 8. Video 9. Abbreviations 10. IC Data Sheets Notes: • Only new circuits compared to the M8 (L01.1 for other regions) chassis are described in this chapter. For the other circuit descriptions, see the manual of the M8 (L01.1) chassis.
Introduction The 'L04' chassis is a global TV chassis for the model year 2004 and is used for TV sets with large screen sizes (from 21 to 36 inch), in Super Flat and Real Flat executions (both in 4:3 and 16:9 variants). There are three types of CRT namely the 100 degrees, 110 degrees and Wide Screen CRT. • The 100 deg.
The standard architecture consists of a Main panel (called 'family board'), a Picture Tube panel, a Side I/O panel, and a Top Control panel. The Main panel consists primarily of conventional components with some surface mounted devices in the audio and video processing part. The functions for video/audio processing, microprocessor (P), and CC/Teletext (TXT) decoder are all combined in one IC (TDA1200x, item 7200), the so-called third generation Ultimate One Chip (UOC-III) or “Hercules”.
Power Supply Block Diagram Figure: Block diagram power supply Stdby_con signal The Hercules generates this signal. This line is logic “low” (0 V) under normal operation and in semi-Standby of the TV, and is “high” (3.3 V) during Standby. Power_down signal The AUX SMPS generates this signal. It is logic “high” (3 .3 V) under normal operation of the TV and goes “low” (0 V) when the AC power (or Mains) input voltage supply goes below 70 V_ac.
B (Hercules port) This port is used to switch the AUX SMPS output V_aux “On/Off”. This is required for DVD and iDTV (for future extensions).
Power ON - To Semi Standby - Out of Semi Standby - Power OFF Figure: Timing diagram Semi Standby Startup Sequence When the set is connected to the AC power, the rectified line voltage (via winding 4-5 of L5531 connected to pin 14 of IC7531) will start the internal voltage source to charge the V_cc capacitor (C2532). The IC starts to switch as soon as the V_cc reaches the V_cc start level of 9.5 V.
Table: Pinning overview TEA1523 Pin Symbol Description 2 Gnd This pin is Ground of the IC. This pin is connected to the supply voltage. An internal current charges the V_cc capacitor (2532), 3 V_cc and the start-up sequence is initiated when this voltage reaches a level of 9.5 V. Note: The output power is disabled when the voltage gets below 9 V (UVLO). Operating range is between 0 to 40 V. 5 RC Frequency setting This pin is connected to the feedback loop.
As C2532 of IC7531 is charged, it will also start to charge the V_cc capacitor (C2511) of IC7511. Via resistor R3519 and C2511, the TEA1506 starts to switch as soon as the V_cc voltage reaches the V_cc start level of is about 11 V. The V_cc voltage is automatically taken over by the main transformer L5512 (winding 2-3) when the V_cc is high enough (when this voltage is even higher than the voltage on C2511, there is no current flow from C2532 to C2511 due to diode D6512).
Standby Mode In this mode, IC7511 (TEA1506) will be totally disabled. So there is no voltage on the main transformer output. But IC7531 (TEA1523) will still work and will provide the necessary output voltages (6V -> 5V, 3.3V, 3V -> 1.8V) to the Hercules (IC7200). Table: PSU voltage overview Voltage Normal operation Stdby mode V_batt 130 - 143 V 0V V_audio +/- 15.5 V 0V +6V 6V 6V +3V 3V 3V Stdby_con 0V 3.
There is a current source inside the UOC at pin 102. This pumps energy in the capacitor connected to this pin producing a pure saw tooth. The vertical drive signals and the E/W correction signal are derived. Pin 108 is the East-West drive (or AVL), and it is a single ended current output. The correction for “horizontal width for changed EHT” from this pin is available by setting the HCO bit to “1”. The Phase-2 Compensation available at pin 113 gives frame correction for high beam currents.
Basic Principle During a scan period, either the Line Transistor or diode(s) conduct to ensure a constant voltage over the deflection coil (that results in a linear current). During the flyback period, the Line Transistor stops conducting, and the flyback capacitor(s) together with the inductance of the deflection coil creates oscillation. First Part of Scan Pin 62 of the UOC delivers the horizontal drive signal for the Line Output stage. This signal is a square pulse of line frequency.
of the LOT, the Line Transistor cannot stop conducting immediately. After the Line Transistor is out of conduction, the flyback pulse is created. The flyback capacitor charges until the current in the deflection coil reduce to zero. Then it discharges through the deflection coil and the deflection current increases from the other direction. The flyback diode conducts and is back to the first part of the scan.
To prevent this from happening, a circuit called Mannheim-circuit is added. This consists of C2415, R3404, R3417 and D6406. During the scan, C2415 is charged via R3417. During the flyback, the S-correction parabola across the S-Cap C2417/C2418 is in its most negative, and D6406 conducts. Thus, C2415 is switched in parallel to C2417/C2418 during flyback. As C2415 is much larger than C2417/C2418, the voltage across C2415 reduces the Mannheim-effect oscillation.
• LCP: Lower Corner Parabola. • EWT: East West Trapezium. The East-West drive circuit realizes them all. The settings can be changed by a remote control. All changed data will be stored into the NVM after the geometry alignment. Panorama For Wide Screen sets, the S-correction of the picture has to adapt between the different picture modes. In particular, between 16:9 Wide Screen and 4:3 picture modes. This is achieved with the (separate) Panorama circuit (see diagram “G”).
• VideoSupply (+200V from primary side of LOT): This supplies the RGB amplifier and Scavem circuit at the CRT panel. Notes: • The V_T voltage (to tuner) is drawn from V_batt. • The EHT voltage is generated by the Line Output Transformer (LOT). The Focus and Vg2 voltages are created with two potentiometers integrated in the transformer. Beam Current The beam current is adjusted with R3451 and R3452. The components R3473, R3453 and C2451 determine the EHT_info characteristic.
BCL • When the BCL pin voltage goes to 2.8 V, the Hercules will start to limit CONTRAST gain. • When it reaches 1.7 V, then the BRIGHTNESS gain limit will start to react. • When BCL pin voltage goes to 0.8 V, the RGB will be blanked. Components TS7483, R3490, R3491, R3492, and C2483 are for fast beam current limiting (e.g. with a Black-to-White pattern). Components R3454, D6451, D6450, C2453, R3493, and C2230 are for average beam current limiting.
During switch-off, the H_out frequency is doubled immediately and the duty cycle is set to 25% fixed, during 43 ms. The RGB outputs are driven “high” to get a controlled discharge of the picture tube with 1 mA during 38 ms. This will decrease the EHT to about half the nominal value (= safety requirement). When bit OSO is set, the white spot/flash during switch-off will be written in overscan and thus will not be visible on the screen.
Vertical Deflection The Frame stage consists fully of discrete components. This has the advantage for better flash behavior than when an IC was used. The Frame differential drive signal from the Hercules comes from a current source. Resistors R3460 and R3461 convert them into a voltage, and feed them into the differential amplifier TS7455 and TS7456. The output of TS7456 is input to the next amplification stage of TS7452.
Tilt and Rotation The rotation control signal is a PWM output from the UOC. It is filtered by R3252, R3246, R3259 and C2259. The DC voltage after filtering at C2259 will be amplified by R3245 (Main Board) and R3390 (CRT panel). The output stage functions similarly as in M8/L01.1 with rotation IC TDA8941P. TS7331/TS7382 and TS7332/TS7381 will function alternatively corresponding to the rotation setting. CRT panel The RGB amplifier stage is exactly the same as in M8/L01.1.
In this chassis the SCAVEM signal is different from its predecessor because the Hercules generates the differential SCAVEM signal inside the IC. The supply of the SCAVEM is taken from V_bat through a 1k5 / 5 W resistor. Compared with the M8/L01.1, this has the advantage of getting better performance for the pattern with tremendous SCAVEM current (like V_sweep).
The Micro Controller ranges in ROM from 128 kB with no TXT-decoder to 128 kB with a 10 page Teletext or with Closed Caption. Block Diagram The block diagram of the Micro Controller application is shown below. Figure: Micro Controller block diagram Basic Specification The Micro Controller operates at the following supply voltages: • +3.3 V_dc at pins 33, 125, and 19. • +1.8 V_dc at pins 126, 36, and 33. • I2C pull up supply: +3.3V_dc.
Pin Configuration and Functionality The ports of the Micro Controller can be configured as follows: • A normal input port. • An input ADC port. • An output Open Drain port. • An output Push-Pull port. • An output PWM port. • Input/Output Port The following table shows the ports used for the L04 control: Table: Micro Controller ports overview Pin Name Description Configuration 32 INT0/ P0.5 IR INT0 31 P1.0/ INT1 PWRDOWN INT1 30 P1.1/ T0 LED P1.1 27 P0.
Pin Name Description Configuration 16 P2.2/ PWM1 SEL_LL'/M P2.2 15 P2.3/ PWM2 STANDBY_CON P2.3 14 P3.0/ ADC0 Light Sensor ADC0 13 P3.1/ ADC1 (for future use) - 10 P3.2/ ADC2 (for future use) - 9 P3.3/ ADC3 KEYBOARD ADC3 7 P2.4/ PWM3 A (for future use) P2.4 6 P2.5/ PWM4 B (for future use) P2.5 3 P1.2/ INT2 C (for future use) INT2 2 P1.4/ RX E (for future use) - 1 P1.5/ TX D (for future use) - The description of each functional pin is explained below: • LED.
Table: LED signal diversity AP/ LED Europe LATAM LED 0 Standby brighter LED 1 Normal dimmer NAFTA LED lighted Standby LED lighted Normal LED 'off' Normal LED 'off' Standby • SCL. This is the clock wire of the two-wire single master bi-directional I2C bus. • SDA. This is the data wire of the two-wire single master bi-directional I2C bus. • STDBY_CON. The Hercules generates this signal. This can enable the MAIN SMPS in normal operation and disable it during Standby.
• Light Sensor. This pin is configured as ADC input for the Light Sensor. • Sel_SC2_Interface. This pin is use to switch between the SC2_CVBS_OUT and the INTF_CVBS_OUT for the SCART_2_CVBS_OUT/ MONITOR_OUT signal. • § 0: Hercules CVBS Output (default) § 1: Interface CVBS Output PWRDOWN. The AUX SMPS generates this signal. Logic “high” (3.3 V) under normal operation of the TV and goes “low” (0 V) when the Mains input voltage supply goes below 70 V_ac. • Keyboard.
• ResetEnabled. This is an output pin to switch the control transistor (pos. TS7202) “high” or “low” for the reset of 1.8 V in case there is a corruption in the Hercules. Tuner and IF The tuner used in this chassis comes from two sources, from Philips and from Alps. Both tuner sources have the same pin configuration so they are 1 to 1 compatible except for the software, which will be selected by means of Option Settings. Some features: • Multi-Standard alignment free PLL-IF, including SECAM L/L'.
The SAW filter used, depends on the application concept (whether it is a QSS concept or an Intercarrier): • OFWM3953M for QSS Video. • OFWK9656M for QSS Audio. • OFWM1971M for Intercarrier. Pin Assignments and Functionality Pin assignment of the Tuner: Table: Pinning Tuner Pin Pin Description DC Voltages 4V for Maximum Gain < 4V for Strong 1 RF-AGC 2 FM Radio Input or N.C - 3 NC (Address Pin) - 4 SCL 0 to 3.3 V_dc 5 SDA 0 to 3.3 V_dc Signal Condition 6/7 Supply Voltage 5 V_dc +/- 0.
Pin assignment of the several SAW filters (depends on region/execution): Table: Pinning SAW filters QSS Video QSS Video QSS Audio Intercarrier (item 1002) (item 1003) (item 1001) (item 1002) 1 Input Input Input Input 2 Input Ground Input Ground 3 Ground Ground Ground Ground 4 Output Output Output Output 5 Output Output Output Output 6 - n.c. - - 7 - n.c.
Option Settings The option settings for the Tuner type can be found in Option setting 1 of the SAM mode. The Option settings for Option 1 are as follows: • Option Byte 1 § Bit 7: OP_PHILIPS_TUNER § Bit 6: OP_FM_RADIO § Bit 5: OP_LNA § Bit 4: OP_ATS § Bit 3: OP_ACI § Bit 2: OP_UK_PNP § Bit 1: OP_VIRGIN_MODE § Bit 0: OP_CHINA For more details on the option settings, please refer to the chapter 8 “Alignments”.
Options The option settings for the Source Selection can be found in Option settings of the SAM mode. The Option settings for Option 5 are as follows: • Option Byte 5 § Bit 7: AV1 § Bit 6: AV2 § Bit 5: AV3 § Bit 4: CVI § Bit 3: SVHS2 § Bit 2: SVHS3 § Bit 1: HOTEL MODE § Bit 0: For more detail on the option settings, please refer to the chapter 8 “Alignments”.
Table: AV Source Select diversity Pin Symbol 51 R/Pr IN3 50 G/Y IN3 49 B/Pb IN3 52 INSSW3 74 CVBS2/Y2 95 AUDIO IN5 L 94 AUDIO IN5 R 73 AUDIO IN3 L 72 AUDIO IN3 R 71 CVBS3/Y3 70 C2/C3 80 AUDIO IN4 L 79 AUDIO IN4 R 78 CVBS4/Y4 77 C4 81 IFVO/SVO/CVBSI 67 AUD OUT HP L 66 AUD OUT HP R 69 AUD OUT LS L (AUD OUT/AM OUT) 68 AUD OUT LS R Remark AV1 (CVI) AV2 (SVHS) Side (SHVS) Monitor Out HP/ LS Out
59 V IN (R/Pr IN2/CX) 58 U IN (B/Pb IN2) 57 Y IN (G/Y IN2/CVBS-Yx) 54 U OUT (INSSW2) 76 AUDIO IN2 L 75 AUDIO IN2 R 86 DVBO/IFVO/FMRO N.C. 65 CVBSO/PIP PIP application 56 Y SYNC 100 nF 55 Y OUT 100 nF 53 V OUT (SWO) N.C. 93 AUD OUT S L N.C. 92 AUD OUT S R N.C.
Table: SCART Source Select diversity Pin Symbol Remark 51 R/Pr IN3 50 G/Y IN3 49 B/Pb IN3 52 INSSW3 74 CVBS2/Y2 86 DVBO/IFVO/FMRO SCART 1 95 AUDIO IN5 L 94 AUDIO IN5 R 93 AUD OUT S L 92 AUD OUT S R 71 CVBS3/Y3 70 C2/C3 81 IFVO/SVO/CVBSI 73 AUDIO IN3 L SCART 2 72 AUDIO IN3 R 67 AUD OUT HP L 66 AUD OUT HP R 80 AUDIO IN4 L 79 AUDIO IN4 R 78 CVBS4/Y4 Side I/O 77 C4 69 AUD OUT LS L (AUD OUT/AM OUT) 68 AUD OUT LS R LS/ HP/ MON OUT
Pin Symbol Remark 59 V IN (R/Pr IN2/CX) 58 U IN (B/Pb IN2) 57 Y IN (G/Y IN2/CVBS-Yx) 54 U OUT(INSSW2) Interface 76 AUDIO IN2 L 75 AUDIO IN2 R 65 CVBSO/PIP for PIP 56 YSYNC 100 nF 55 YOUT 100 nF 53 VOUT(SWO) N.C. Audio Source Selection The signals coming out of the DEMDEC (internal demodulator/decoder block of the Hercules) are selectable and consist of the following (depending on the transmission): • DEC L/R (Can be NICAM, FM 2CS, or BTSC Stereo).
• SCART2 Output (EU) or Monitor Output (LA/NA/AP) assigned to Headphone Output . • Constant Level Output assigned to Loudspeaker Output . Video Source Selection Video source selection is done inside the Hercules. Therefore it provides a video switch with 3 external CVBS inputs and a CVBS output. All CVBS inputs can be used as Yinput for Y/C signals. However, only 2 Y/C sources can be selected because the circuit has 2 chroma inputs.
Features The features included in the Hercules are as follows: • Brightness Control. • Contrast Control. • Saturation Control. • Sharpness Control. • Peak White Limiter. • Beam Current Limiter. • Black Stretch (Contrast Plus). For sets with the TDA9178, there are two extra features: • Luminance Transient Improvement (LTI). • Color Transient Improvement (CTI).
Block Diagram Following diagram is the block diagram of the video processing part: Figure: Video processing block diagram LTI/CTI The TDA9178 is an I2C-bus controlled IC (INCREDIBLE chip) with YUV interface. This IC can do mainly histogram processing, color transient improvement (CTI) and line transient improvement (LTI). • Luminance Vector Processing involves histogram function, which provides scene dependent contrast improvement, adaptive black and white point stretching.
• Color Vector Processing involves skin tone correction, green enhancement and blue stretch. • Spectral Processor involves step improvement processing, contour processing, smart sharpness control, color dependant sharpness and Color Transient Improvement. • Noise detector, feature mode detector and cue flash functions. • Demonstration mode shows all the improvement features in one picture. Table: Pinning overview TDA9178 Pin Symbol Description 1 SC Sandcastle input pin 2 n.c.
Pin Symbol Description 17 U out -(B-Y) signal output pin 18 V ee Ground pin 19 Y out Luminance output pin 20 V cc Supply-voltage pin 21 S out Luminance output for SCAVEM 22 CF Cue-flash output pin 23 n.c. Not connected pin 24 n.c. Not connected pin Options The option settings allow for process of the video as per set specification. The option settings can be found in “Option 2” and “Option 6” in the SAM mode.
• Option Byte 6 § Bit 7: OP_PERSONAL_ZAPPING, § Bit 6: § Bit 5: OP_FMTRAP § Bit 4: OP_COMBFILTER § Bit 3: OP_ACTIVE_CONTROL § Bit 2: OP_VIDEO_TEXT § Bit 1 :OP_LIGHT_SENSOR, § Bit 0: OP_DUAL_TEXT For more details on the option settings, please refer to the chapter 8 “Alignments”. Audio Processing The audio decoding is done entirely via the Hercules. The IF output from the Tuner is fed directly to either the Video-IF or the Sound-IF input depending on the type of concept chosen.
Diversity The diversity for the Audio decoding can be broken up into two main concepts: • The Quasi Split Sound concept used in Europe and some AP sets. • The Inter Carrier concept, used in NAFTA and LATAM. The UOC-III family makes no difference anymore between QSS- and Intercarrier IF, nearly all types are software-switchable between the two SAW-filter constructions. Simple data settings are required for the set to determine whether it is using the Inter Carrier or the QSS concept.
Functionality The features available in the Hercules are as follows: • Treble and Bass Control. • Surround Sound Effect that includes: • § Incredible Stereo. § Incredible Mono. § 3D Sound (not for AV Stereo). § TruSurround (not for AV Stereo). § Virtual Dolby Surround, VDS422 (not for AV Stereo). § Virtual Dolby Surround, VDS423 (not for AV Stereo). § Dolby Pro-Logic (not for AV Stereo). Bass Feature that includes: § Dynamic Ultra-Bass. § Dynamic Bass Enhancement.
Muting is done via the VOLUME_MUTE line connected to pin 2 of the amplifier-IC and coming from the UOC.
Abbreviation list Abbreviation Description 2CS 2 Carrier (or Channel) Stereo ACI Automatic Channel Installation: algorithm that installs TV sets directly from cable network by means of a predefined TXT page ADC Analogue to Digital Converter AFC Automatic Frequency Control: control signal used to tune to the correct frequency AFT Automatic Fine Tuning AGC Automatic Gain Control: algorithm that controls the video input of the feature box AM Amplitude Modulation AP Asia Pacific region AR Asp
BTSC Broadcast Television Standard Committee. Multiplex FM stereo sound system, originating from the USA and used e.g.
DVD Digital Versatile Disc EEPROM Electrically Erasable and Programmable Read Only Memory EHT Extra High Tension EHT-INFO Extra High Tension information EPG Electronic Programming Guide EU Europe EW East West, related to horizontal deflection of the set EXT External (source), entering the set via SCART or Cinch FBL Fast Blanking: DC signal accompanying RGB signals FILAMENT Filament of CRT FM Field Memory or Frequency Modulation H Horizontal sync signal HP Headphone I Monochrome TV
LED Light Emitting Diode L/L' Monochrome TV system. Sound carrier distance is 6.5 MHz. L' is Band I, L is all bands except for Band I LS Large Screen or Loudspeaker M/N Monochrome TV system. Sound carrier distance is 4.5 MHz NC Not Connected NICAM Near Instantaneous Compounded Audio Multiplexing. This is a digital sound system, mainly used in Europe. NTSC National Television Standard Committee. Color system mainly used in North America and Japan. Color carrier NTSC M/N = 3.579545 MHz, NTSC 4.
PCB Printed Circuit board PLL Phase Locked Loop. Used for e.g. FST tuning systems.
SVHS Super Video Home System SW Software THD Total Harmonic Distortion TXT Teletext uP Microprocessor UOC Ultimate One Chip V Vertical sync signal V_BAT Main supply voltage for the deflection stage (mostly 141 V) V-chip Violence Chip VCR Video Cassette Recorder WYSIWYR What You See Is What You Record: record selection that follows main picture and sound XTAL Quartz crystal YC Luminance (Y) and Chrominance (C) signal
IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as 'black boxes' in the electrical diagrams (with the exception of 'memory' and 'logic' ICs).
All Models (7661) - Chassis Overview
All Models (7661) - Power Supply [A1]
All Models (7661) - Deflection [A2]
All Models (7661) - Tuner IF [A3]
All Models (7661) - Hercules [A4]
All Models (7661) - Features & Connectivities [A5]
All Models (7661) - Class D - Audio Amplifier [A6]
All Models (7661) - Audio Amplifier [A7]
All Models (7661) - Rear I/O Cinch [A8]
All Models (7661) - Front Control [A9]
All Models (7661) - DVD Power Supply [A10]
All Models (7661) - CRT Panel [B1]
All Models (7661) - Eco Scavem [B2]
All Models (7661) - Side AV + Headphone Panel [D]
USED ONLY IN MODELS: 25PT6341/85 (7661) - Side Jack Panel (Wide)
NOT USED IN MODELS: , 25PT6341/85, 27MS6341/37, 27PT5441/37, 32MS6341/37, 32PT5441/37, 33PT5441/85 (7661) - Top Control Panel [E]
USED ONLY IN MODELS: 27MS6341/37, 32MS6341/37 (7661) - Top Control Panel (Round)
USED ONLY IN MODELS: 26PW6341/37, 28PW6341/85, 30PW6341/37, 32PW6341/85 (7661) - Linearity & Panorama Panel [G]
NOT USED IN MODELS: , 27ST6210/27 (7661) - LTI/CTI Interface Panel [H]
NOT USED IN MODELS: , 25PT6341/85, 27PT5441/37, 32PT5441/37, 33PT5441/85 (7661) - Front Interface Panel [J]
USED ONLY IN MODELS: 27ST6210/27, (7661) - EPS Module
USED ONLY IN MODELS: 27ST6210/27, (7661) - SP/LS Module
USED ONLY IN MODELS: 27ST6210/27, (7661) - ITV Interface Module
All Models (7661) - Layout Mono Carrier (Top Side)
All Models (7661) - Layout Mono Carrier (Overview Bottom Side)
All Models (7661) - Layout CRT Panel (Top Side)
All Models (7661) - Layout CRT Panel (Bottom Side)
All Models (7661) - Layout Side AV + Headphone Panel (Top Side)
All Models (7661) - Layout Side AV + Headphone Panel (Bottom Side)
USED ONLY IN MODELS: 25PT6341/85 (7661) - Side Jack Panel - Wide (Top Side)
USED ONLY IN MODELS: 25PT6341/85 (7661) - Side Jack Panel - Wide (Bottom Side)
NOT USED IN MODELS: , 25PT6341/85, 27MS6341/37, 27PT5441/37, 32MS6341/37, 32PT5441/37, 33PT5441/85 (7661) - Layout Top Control Panel (Top Side)
NOT USED IN MODELS: , 25PT6341/85, 27MS6341/37, 27PT5441/37, 32MS6341/37, 32PT5441/37, 33PT5441/85 (7661) - Layout Top Control Panel (Bottom Side)
USED ONLY IN MODELS: 27MS6341/37, 32MS6341/37 (7661) - Top Control Panel - Round (Top Side)
USED ONLY IN MODELS: 27MS6341/37, 32MS6341/37 (7661) - Top Control Panel - Round (Bottom Side)
USED ONLY IN MODELS: 26PW6341/37, 28PW6341/85, 30PW6341/37, 32PW6341/85 (7661) - Layout Linearity & Panorama Panel (Top Side)
NOT USED IN MODELS: , 27ST6210/27 (7661) - Layout LTI/CTI Interface Panel (Top Side)
NOT USED IN MODELS: , 27ST6210/27 (7661) - Layout LTI/CTI Interface Panel (Bottom Side)
NOT USED IN MODELS: , 25PT6341/85, 27PT5441/37, 32PT5441/37, 33PT5441/85 (7661) - Layout Front Interface Panel (Top Side)
NOT USED IN MODELS: , 25PT6341/85, 27PT5441/37, 32PT5441/37, 33PT5441/85 (7661) - Layout Front Interface Panel (Bottom Side)
USED ONLY IN MODELS: 27ST6210/27, (7661) - EPS Module (Top Side)
USED ONLY IN MODELS: 27ST6210/27, (7661) - SP/LS Module (Top Side)
USED ONLY IN MODELS: 27ST6210/27, (7661) - SP/LS Module (Bottom Side)
USED ONLY IN MODELS: 27ST6210/27, (7661) - ITV Interface Module (Top Side)
USED ONLY IN MODELS: 27ST6210/27, (7661) - ITV Interface Module (Bottom Side)
All Models (7661) - Testpoint Overview Mono Carrier
All Models (7661) - Testpoint Overview CRT
All Models (7661) - Testpoint Overview LTI Panel
All Models (7661) - Wiring Diagram
All Models (7661) - Block Diagram Supply and Deflection
All Models (7661) - Block Diagram Video
All Models (7661) - Block Diagram Audio/Control
All Models (7661) - I2C and Supply Voltage Overview
25PT6341/85 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0028 Degaussing Coil Holder (2 Used). . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0050 Nameplate (part of Cabinet Front Assemb ly). . . . . . . . . . .
25PT6341/85 (continued) 4180 Res, Zero ohm, "Chip" Jumper . . . . . 3198 021 90020 Top Control Panel Top Control Panel Main Chassis Main Chassis CBA Main Chassis . . . . . . . . . . . 1000 Tuner, V+U PLL . . . . . . . . . . 1002 S.A.W. Filter, 45MHz75, OFWM1971M. 1005 Connector, 3 Pin . . . . . . . . . 1137 MDIN Socket. . . . . . . . . . . . 1204 Connector, 7 Pin . . . . . . . . . 1205 Crystal Resonator, 24MHz576. . . . 1207 Connector, 7 Pin . . . . . . . . . 1212 Connector, 12 Pin. . . . . . . . .
25PT6341/85 (continued) 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2691 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 3221 3222 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235 3236 Cap, Cap, Cap, Cap, Cap, Ca
25PT6341/85 (continued) 3499 3500 3501 3502 S 3503 3504 3505 3507 S 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3524 3527 3528 3529 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3681 3684 3685 3686 3687 3690 3691 3693 3694 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 4015 4106 4107 4108 4116 4136 4209 4212 4221 4222 Res, 680K, 5%, 1/10W, M
25PT6341/85 (continued) 6459 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6538 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6691 6692 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7482 7483 7484 7511 7512 7513 7514 7531 7532 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 9116 9120 9121 9122 9123 9124 9125 9126 9128 9129 9138 9202 9203 Diode, Rect, RGP10G. . . .
25PT6341/85 (continued) 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9683 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
26PW6341/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0001 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0021 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0039 Linearity & Panorama Panel Bracket . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . .
26PW6341/37 (continued) 4617 4625 4635 4637 6610 6611 6625 6633 6635 6636 7610 7627 7630 7635 9613 9614 9615 9616 9617 9618 Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Diode, Signal, BAS316. . . . Zener Diode, 6.8 volt. . . . Zener Diode, 2.7 volt. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . IC, TDA9178T/N1. . . . . . . Transistor, NPN, PMBT2369. . Transistor, NPN, BC847B. . .
26PW6341/37 (continued) 2273 2274 2275 2276 2279 2280 2282 2288 2289 2404 2406 2408 2409 2410 2411 2412 2413 2414 2415 2416 2419 2420 2425 2428 2451 2453 2454 2456 2457 2459 2460 2461 2462 2463 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2491 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2528 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 Cap, 100u, 20%, 25v, Electrolytic. . .
26PW6341/37 (continued) 3253 3257 3258 3259 3260 3261 3262 3265 3266 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3283 3284 3285 3287 3289 3290 3291 3292 3293 3294 3295 3296 3401 3404 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3477 3478 3481 3482 3483 S 3484 S 3485 3486 3489 3490 3491 3492 3493 3495 3497 3498 3499 Res, Res, Res, Res, Res
26PW6341/37 (continued) 4537 4604 4610 4612 4620 4631 4635 4637 4642 4644 4645 4646 4648 4649 4691 4692 4694 4696 4910 4914 4915 4916 4917 4921 5001 5002 5201 5202 5203 5205 5206 5207 5208 5209 5210 5211 5212 5213 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6403 6406 6407 6408 6410 6411 6412 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 Res, Zero ohm, "Chip" Jumpe
26PW6341/37 (continued) 9210 9211 9212 9213 9214 9216 9217 9218 9219 9220 9221 9222 9223 9224 9225 9226 9227 9228 9229 9230 9231 9232 9233 9234 9235 9236 9237 9238 9239 9240 9241 9244 9245 9246 9247 9248 9249 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9402 9410 9417 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 Wire Wire Wire Wire Wire Wi
27MS6341/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0040 Power Button Cover (part of Cabinet Fro nt Assembly) . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0049 Power Button Shaft (part of Cabinet Fro nt Assembly) . . . . . .
27MS6341/37 (continued) 2176 2178 2180 3150 3151 3152 3153 3154 3156 3157 3160 9181 Cap, Cap, Cap, Res, Res, Res, Res, Res, Res, Res, Res, Wire 100n, 10%, 16v, Ceramic . . . . 470p, 10%, 50v, Ceramic . . . . 2u2, 20%, 50v, Electrolytic . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 75 ohm, 5%, 1/6W, Carbon Film . 820 ohm, 5%, 1/6W, Carbon Film. 820 ohm, 5%, 1/6W, Carbon Film. 100 ohm, 5%, 1/6W, Carbon Film. Jumper, 0.
27MS6341/37 (continued) 2517 2519 2528 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 Cap, Cap, Cap, Cap, Cap,
27MS6341/37 (continued) S S S S 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3527 3528 3529 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3690 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 Res, 22 ohm, 5%
27MS6341/37 (continued) 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6538 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7532 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 Diode, Rect, DMV1500M . . .
27MS6341/37 (continued) 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
27PT5441/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button and Control Buttons Assemb ly. . . . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0029 Plastic Facade (part of Cabinet Front A ssembly) . . . . . . . . . . . . . . . 0041 Light Guide. . . . . . . . . . . . . . 0050 Nameplate (part of Cabinet Front Assemb ly). . . . . . . . . . .
27PT5441/37 (continued) Top Control Panel Top Control Panel Main Chassis Main Chassis CBA Main Chassis . . . . . . . . . . . . . 1000 Tuner, V+U PLL . . . . . . . . . . . . 1002 S.A.W. Filter, 45MHz75, OFWM1971M. . . 1005 Connector, 3 Pin . . . . . . . . . . . 1137 MDIN Socket. . . . . . . . . . . . . . 1204 Connector, 7 Pin . . . . . . . . . . . 1205 Crystal Resonator, 24MHz576. . . . . . 1207 Connector, 7 Pin . . . . . . . . . . . 1212 Connector, 12 Pin. . . . . . . . . . . 1223 12 Pin Cinch Socket. . . .
27PT5441/37 (continued) 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2691 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 3221 3222 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235 3236 3237 3238 3239 3240 3241 Cap, Cap, Cap, Cap, Cap, Ca
27PT5441/37 (continued) 3502 S 3503 3504 3505 S 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3681 3684 3685 3686 3687 3690 3691 3693 3694 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 4015 4106 4107 4108 4116 4136 4209 4212 4221 4222 4223 4226 4227 4240 4241 4470 Res, 220 ohm, 20%, 1/2W
27PT5441/37 (continued) 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6691 6692 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7408 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 9116 9120 9121 9122 9123 9124 9125 9126 9128 9129 9138 9202 9203 9204 9205 9206 9207 9208 9209 9210 9211 9212 9213 9214 9216 9217 Diode, Signal, BAT51, SOD32
27PT5441/37 (continued) 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9683 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
27PT6441/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
27PT6441/37 (continued) 2176 2178 2180 3150 3151 3152 3153 3154 3156 3157 3160 9181 Cap, Cap, Cap, Res, Res, Res, Res, Res, Res, Res, Res, Wire 100n, 10%, 16v, Ceramic . . . . 470p, 10%, 50v, Ceramic . . . . 2u2, 20%, 50v, Electrolytic . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 75 ohm, 5%, 1/6W, Carbon Film . 820 ohm, 5%, 1/6W, Carbon Film. 820 ohm, 5%, 1/6W, Carbon Film. 100 ohm, 5%, 1/6W, Carbon Film. Jumper, 0.
27PT6441/37 (continued) 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 Cap, Cap, Cap, Cap, Cap,
27PT6441/37 (continued) S S S S 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3690 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 Res, 120 ohm, 5
27PT6441/37 (continued) 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 Diode, BAV21WS . . . . . .
27PT6441/37 (continued) 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire 100R Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
27PT6442/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0021 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
27PT6442/37 (continued) 2178 2180 3150 3151 3152 3153 3154 3156 3157 3160 9181 Cap, Cap, Res, Res, Res, Res, Res, Res, Res, Res, Wire 470p, 10%, 50v, Ceramic . . . . 2u2, 20%, 50v, Electrolytic . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 75 ohm, 5%, 1/6W, Carbon Film . 820 ohm, 5%, 1/6W, Carbon Film. 820 ohm, 5%, 1/6W, Carbon Film. 100 ohm, 5%, 1/6W, Carbon Film. Jumper, 0.58MM. . . . . . . . .
27PT6442/37 (continued) 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 Cap, Cap, Cap, Cap, Cap,
27PT6442/37 (continued) S S S S 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3690 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 Res, 22 ohm, 5%
27PT6442/37 (continued) 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 9116 9120 9121 Zener Diode, 68 volt . . .
27PT6442/37 (continued) 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
27ST6210/27 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0005 ITV Cabinet Back Assembly. . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0021 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . .
27ST6210/27 (continued) 1205 1207 1212 1213 1219 1220 1223 1227 1229 1236 1262 1280 S 1401 1404 1451 1452 1454 S 1500 S 1503 1504 1505 1507 1682 1692 1693 2001 2004 2006 2007 2008 2103 2104 2105 2106 2131 2132 2133 2134 2203 2204 2205 2206 2207 2208 2209 2210 2211 2212 2213 2214 2215 2216 2217 2218 2222 2223 2224 2225 2226 2229 2230 2231 2232 2233 2234 2235 2236 2237 2238 2239 2240 2241 2242 2243 2244 2245 2246 2247 2248 2249 2250 2251 2252 2253 2254 2255 2256 2257 2260 2261 2262 2263 Crystal Resonator, 24
27ST6210/27 (continued) 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3129 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 3221 3222 3224 3226 3227 3228 3229 3230 3231 3232 3235 3236 3237 3238 3239 3240 3241 3242 3243 3244 3247 3248 3249 3250 3251 3254 3257 3258 3260 3261 3262 3264 3269 3270 Cap, Cap, Cap, Cap, Cap, Ca
27ST6210/27 (continued) 3517 3518 3519 3520 3521 3522 3523 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3603 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3619 3620 3621 3625 3626 3628 3634 3635 3637 3690 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 4015 4101 4102 4103 4109 4110 4111 4130 4136 4209 4211 4212 4221 4222 4223 4226 4227 4240 4241 4470 4492 4533 4534 4535 4537 4604 4605 4610 Res, Res, Res, Res, Res, Re
27ST6210/27 (continued) 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9114 9116 9120 9121 9122 9123 9124 9125 9126 9128 9129 9138 9201 9202 9203 9204 9205 9206 9207 9208 9209 9210 9211 9212 9213 9214 9216 9217 Diode, Signal, BAS316. . .
27ST6210/27 (continued) 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9607 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
28PW6341/85 - Manual no. 7661 Cabinet Parts Cabinet Parts 0001 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0039 Linearity & Panorama Panel Bracket . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . .
28PW6341/85 (continued) 4625 4635 4637 6610 6611 6625 6633 6635 6636 7610 7627 7630 7635 9613 9614 9615 9616 9617 9618 Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Diode, Signal, BAS316. . . . Zener Diode, 6.8 volt. . . . Zener Diode, 2.7 volt. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . IC, TDA9178T/N1. . . . . . . Transistor, NPN, PMBT2369. . Transistor, NPN, BC847B. . . Transistor, PNP, BC857B. . . Wire Jumper, 0.
28PW6341/85 (continued) 2274 2275 2276 2279 2280 2282 2288 2289 2404 2406 2408 2409 2410 2411 2412 2413 2414 2415 2416 2419 2420 2425 2428 2451 2453 2454 2456 2457 2459 2460 2461 2462 2463 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2491 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2528 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 Cap, 100n, 10%, 16v, Ceramic . . . . .
28PW6341/85 (continued) 3257 3258 3259 3260 3261 3262 3265 3266 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3283 3284 3285 3287 3289 3290 3291 3292 3293 3294 3295 3296 3401 3404 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3477 3478 3481 3482 3483 S 3484 S 3485 3486 3489 3490 3491 3492 3493 3495 3497 3498 3499 3500 Res, Res, Res, Res, Res
28PW6341/85 (continued) 4604 4610 4612 4620 4631 4635 4637 4642 4644 4645 4646 4648 4649 4691 4692 4694 4696 4910 4914 4915 4916 4917 4921 5001 5002 5201 5202 5203 5205 5206 5207 5208 5209 5210 5211 5212 5213 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6403 6406 6407 6408 6410 6411 6412 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 Res, Zero ohm, "Chip" Jumpe
28PW6341/85 (continued) 9211 9212 9213 9214 9216 9217 9218 9219 9220 9221 9222 9223 9224 9225 9226 9227 9228 9229 9230 9231 9232 9233 9234 9235 9236 9237 9238 9239 9240 9241 9244 9245 9246 9247 9248 9249 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9402 9410 9417 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 Wire Wire Wire Wire Wire Wi
29PT6441/44 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0021 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
29PT6441/44 (continued) 2175 2176 2178 2180 3150 3151 3152 3153 3154 3156 3157 3160 9181 Cap, Cap, Cap, Cap, Res, Res, Res, Res, Res, Res, Res, Res, Wire 2u2, 20%, 50v, Electrolytic . . 100n, 10%, 16v, Ceramic . . . . 470p, 10%, 50v, Ceramic . . . . 2u2, 20%, 50v, Electrolytic . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 75 ohm, 5%, 1/6W, Carbon Film . 820 ohm, 5%, 1/6W, Carbon Film. 820 ohm, 5%, 1/6W, Carbon Film.
29PT6441/44 (continued) 2513 2514 2515 2516 2517 2519 2528 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 S 2570 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 Cap, Cap, Cap, Cap, Cap,
29PT6441/44 (continued) S S S S 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3506 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3527 3528 3529 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3690 3975 3985 3988 Res, 2K2, 5%, 1
29PT6441/44 (continued) 6205 6207 6209 6210 6211 6403 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6538 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7532 7541 7561 7571 7573 7601 7603 Zener Diode, 27 volt . . .
29PT6441/44 (continued) 9296 9297 9298 9299 9401 9407 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wi
29PT6441/85 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
29PT6441/85 (continued) 2178 2180 3150 3151 3152 3153 3154 3156 3157 3160 9181 Cap, Cap, Res, Res, Res, Res, Res, Res, Res, Res, Wire 470p, 10%, 50v, Ceramic . . . . 2u2, 20%, 50v, Electrolytic . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 47K, 5%, 1/6W, Carbon Film. . . 22K, 5%, 1/6W, Carbon Film. . . 75 ohm, 5%, 1/6W, Carbon Film . 820 ohm, 5%, 1/6W, Carbon Film. 820 ohm, 5%, 1/6W, Carbon Film. 100 ohm, 5%, 1/6W, Carbon Film. Jumper, 0.58MM. . . . . . . . .
29PT6441/85 (continued) 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 Cap, Cap, Cap, Cap, Cap,
29PT6441/85 (continued) S S S S 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3690 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 Res, 22 ohm, 5%
29PT6441/85 (continued) 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 9116 9120 9121 Zener Diode, 68 volt . . .
29PT6441/85 (continued) 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
29PT6541/44 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0021 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
29PT6541/44 (continued) 9616 9617 9618 Wire Jumper, 0.58MM. . . . . . . . . . Wire Jumper, 0.58MM. . . . . . . . . . Wire Jumper, 0.58MM. . . . . . . . . . 3198 036 90010 3198 036 90010 3198 036 90010 Linearity & Panorama Panel Linearity & Panorama Panel Side Jack Panel Side Jack Panel CBA Side Jack Panel. . . . . . . . . . . 1232 Headphone Jack . . . . . . . . . . . 1250 A/V Jack . . . . . . . . . . . . . . 1252 Connector, 7 Pin . . . . . . . . . . 1254 Connector, 5 Pin . . . . . . . . . .
29PT6541/44 (continued) 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 S 2508 S 2509 2511 2512 2513 2514 2515 2516 2517 2519 2528 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 S 2570 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 Cap, 470p, 5%, 50v, Ceramic. .
29PT6541/44 (continued) S S S S 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3506 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3527 3528 3529 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 Res, 100 ohm, 5
29PT6541/44 (continued) 5212 5213 5214 5215 5216 5401 5402 5405 5408 5450 5451 5500 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6403 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6538 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 Fixed Inductor, 100MHz, 120
29PT6541/44 (continued) 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9401 9407 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 Wire Wire Wire Wire Wire Wi
29PT6541/85 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0021 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
29PT6541/85 (continued) 9616 9617 9618 Wire Jumper, 0.58MM. . . . . . . . . . Wire Jumper, 0.58MM. . . . . . . . . . Wire Jumper, 0.58MM. . . . . . . . . . 3198 036 90010 3198 036 90010 3198 036 90010 Linearity & Panorama Panel Linearity & Panorama Panel Side Jack Panel Side Jack Panel CBA Side Jack Panel. . . . . . . . . . . 1232 Headphone Jack . . . . . . . . . . . 1250 A/V Jack . . . . . . . . . . . . . . 1252 Connector, 7 Pin . . . . . . . . . . 1254 Connector, 5 Pin . . . . . . . . . .
29PT6541/85 (continued) 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 Cap, 470p, 5%, 50v, Ceramic. .
29PT6541/85 (continued) S S S S 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3523 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 Res, 3K3, 5%, 1
29PT6541/85 (continued) 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6403 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6571 6572 6573 6575 6602 6656 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 Filter, Mains, 5mH, 2A . .
29PT6541/85 (continued) 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9401 9407 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9688 9689 9694 9695 9910 9911 9913 9914 9915 Wire Wire Wire Wire Wire Wi
30PW6341/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0039 Linearity & Panorama Panel Bracket . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . .
30PW6341/37 (continued) 4625 4635 4637 6610 6611 6625 6633 6635 6636 7610 7627 7630 7635 9613 9614 9615 9616 9617 9618 Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Diode, Signal, BAS316. . . . Zener Diode, 6.8 volt. . . . Zener Diode, 2.7 volt. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . IC, TDA9178T/N1. . . . . . . Transistor, NPN, PMBT2369. . Transistor, NPN, BC847B. . . Transistor, PNP, BC857B. . . Wire Jumper, 0.
30PW6341/37 (continued) 2274 2275 2276 2279 2280 2282 2288 2289 2404 2406 2408 2409 2410 2411 2412 2413 2414 2415 2419 2420 2425 2428 2451 2453 2454 2456 2457 2459 2460 2461 2462 2463 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 Cap, 100n, 10%, 16v, Ceramic . . .
30PW6341/37 (continued) 3261 3262 3265 3266 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3283 3284 3285 3287 3289 3290 3291 3292 3293 3294 3295 3296 3401 3404 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 S 3484 S 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 S 3503 3504 Res, 4K7, 5%, 1/16W,
30PW6341/37 (continued) 4642 4644 4645 4646 4648 4649 4691 4692 4694 4696 4910 4914 4915 4916 4917 4921 5001 5002 5201 5202 5203 5205 5206 5207 5208 5209 5210 5211 5212 5213 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6403 6406 6407 6408 6410 6411 6412 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 Res, Zero ohm, "Chip" Jumpe
30PW6341/37 (continued) 9221 9222 9223 9224 9225 9226 9227 9228 9229 9230 9231 9232 9233 9234 9235 9236 9237 9238 9239 9240 9241 9244 9245 9246 9247 9248 9249 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9402 9410 9417 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 Wire Wire Wire Wire Wire Wi
32MS6341/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0040 Power Button Cover (part of Cabinet Fro nt Assembly) . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0049 Power Button Shaft (part of Cabinet Fro nt Assembly) . . . . . .
32MS6341/37 (continued) 9618 Wire Jumper, 0.58MM. . . . . . . . . . 3198 036 90010 Linearity & Panorama Panel Linearity & Panorama Panel Side Jack Panel Side Jack Panel CBA Side Jack Panel. . . . . . . . . . . 1232 Headphone Jack . . . . . . . . . . . 1250 A/V Jack . . . . . . . . . . . . . . 1252 Connector, 7 Pin . . . . . . . . . . 1254 Connector, 5 Pin . . . . . . . . . . 1278 Connector, 4 Pin . . . . . . . . . . 2171 Cap, 330p, 10%, 50v, Ceramic . . . . 2172 Cap, 330p, 10%, 50v, Ceramic . . . .
32MS6341/37 (continued) 2460 2461 2462 2463 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 Cap, 470u, 20%, 16v, Electroly
32MS6341/37 (continued) S S S S 3409 3410 3411 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3507 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 Res, 1K8, 5%, 1
32MS6341/37 (continued) 5211 5212 5213 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6401 6403 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7205 7207 7208 7209 7210 7401 7402 Fixed Inductor, 100MHz, 120
32MS6341/37 (continued) 9248 9249 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9401 9407 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 Wire Wire Wire Wire Wire Wi
32PT5441/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button and Control Buttons Assemb ly. . . . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0029 Plastic Facade (part of Cabinet Front A ssembly) . . . . . . . . . . . . . . . 0041 Light Guide. . . . . . . . . . . . . . 0050 Nameplate (part of Cabinet Front Assemb ly). . . . . . . . . . .
32PT5441/37 (continued) 3157 3160 9181 Res, 820 ohm, 5%, 1/6W, Carbon Film. . Res, 100 ohm, 5%, 1/6W, Carbon Film. . Wire Jumper, 0.58MM. . . . . . . . . . 3198 011 08210 3198 011 01010 3198 036 90010 Top Control Panel Top Control Panel Main Chassis Main Chassis CBA Main Chassis . . . . . . . . . . . 1000 Tuner, V+U PLL . . . . . . . . . . 1002 S.A.W. Filter, 45MHz75, OFWM1971M. 1005 Connector, 3 Pin . . . . . . . . . 1137 MDIN Socket. . . . . . . . . . . . 1204 Connector, 7 Pin . . . . . . . . .
32PT5441/37 (continued) 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2691 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 3221 3222 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235 3236 3237 Cap, Cap, Cap, Cap, Cap, Ca
32PT5441/37 (continued) 3493 3494 3495 3497 3498 3499 3500 3501 3502 S 3503 3504 3505 3507 S 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3681 3684 3685 3686 3687 3690 3691 3693 3694 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 4015 4106 4107 4108 4116 4136 4209 4212 Res, 2K2, 5%, 1/16W, Me
32PT5441/37 (continued) 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6691 6692 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 9116 9120 9121 9122 9123 9124 9125 9126 9128 9129 Diode, Signal, BAS316. . .
32PT5441/37 (continued) 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9683 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
32PT6441/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
32PT6441/37 (continued) Side Jack Panel Side Jack Panel CBA Side Jack Panel. . . . . . . . . . . 1232 Headphone Jack . . . . . . . . . . . 1250 A/V Jack . . . . . . . . . . . . . . 1252 Connector, 7 Pin . . . . . . . . . . 1254 Connector, 5 Pin . . . . . . . . . . 1278 Connector, 4 Pin . . . . . . . . . . 2171 Cap, 330p, 10%, 50v, Ceramic . . . . 2172 Cap, 330p, 10%, 50v, Ceramic . . . . 2173 Cap, 330p, 10%, 50v, Ceramic . . . . 2174 Cap, 330p, 10%, 50v, Ceramic . . . .
32PT6441/37 (continued) 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 Cap, 470p, 5%, 50v, Ceramic. .
32PT6441/37 (continued) S S S S 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3507 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 Res, 1K, 5%, 1/
32PT6441/37 (continued) 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6401 6403 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7205 7207 7208 7209 7210 7401 7402 7403 7404 7405 Fixed Inductor, 100MHz, 120
32PT6441/37 (continued) 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9401 9407 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 Wire Wire Wire Wire Wire Wi
32PT6442/37 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . . 0048 Cabinet Back Screw Cover (2 Used). . .
32PT6442/37 (continued) Side Jack Panel Side Jack Panel CBA Side Jack Panel. . . . . . . . . . . 1232 Headphone Jack . . . . . . . . . . . 1250 A/V Jack . . . . . . . . . . . . . . 1252 Connector, 7 Pin . . . . . . . . . . 1254 Connector, 5 Pin . . . . . . . . . . 1278 Connector, 4 Pin . . . . . . . . . . 2171 Cap, 330p, 10%, 50v, Ceramic . . . . 2172 Cap, 330p, 10%, 50v, Ceramic . . . . 2173 Cap, 330p, 10%, 50v, Ceramic . . . . 2174 Cap, 330p, 10%, 50v, Ceramic . . . .
32PT6442/37 (continued) 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 Cap, 470p, 5%, 50v, Ceramic. .
32PT6442/37 (continued) S S S S 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 3484 3485 3486 3489 3490 3491 3493 3494 3495 3497 3498 3499 3500 3501 3502 3503 3504 3505 3507 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 Res, 1K, 5%, 1/
32PT6442/37 (continued) 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6401 6403 6404 6406 6407 6408 6410 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6694 7200 7201 7203 7204 7205 7207 7208 7209 7210 7401 7402 7403 7404 7405 Fixed Inductor, 100MHz, 120
32PT6442/37 (continued) 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9401 9407 9410 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 Wire Wire Wire Wire Wire Wi
32PW6341/85 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button (part of Cabinet Front Ass embly) . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0030 Chassis Tray . . . . . . . . . . . . . 0039 Linearity & Panorama Panel Bracket . . 0041 Light Guide (part of Cabinet Front Asse mbly). . . . . . . . . . . . . . . . .
32PW6341/85 (continued) 4635 4637 6610 6611 6625 6633 6635 6636 7610 7627 7630 7635 9613 9614 9615 9616 9617 9618 Res, Zero ohm, "Chip" Jumper Res, Zero ohm, "Chip" Jumper Diode, Signal, BAS316. . . . Zener Diode, 6.8 volt. . . . Zener Diode, 2.7 volt. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . Diode, Signal, BAS316. . . . IC, TDA9178T/N1. . . . . . . Transistor, NPN, PMBT2369. . Transistor, NPN, BC847B. . . Transistor, PNP, BC857B. . . Wire Jumper, 0.58MM. . . . . Wire Jumper, 0.58MM.
32PW6341/85 (continued) 2275 2276 2279 2280 2282 2288 2289 2404 2406 2408 2409 2410 2411 2412 2413 2414 2415 2419 2420 2425 2428 2451 2453 2454 2456 2457 2459 2460 2461 2462 2463 2464 2465 2467 2468 2469 2470 2484 2486 2487 2489 2500 2503 2504 2505 2511 2512 2513 2514 2515 2516 2517 2519 2530 2531 2532 2533 2534 2535 2536 2538 2539 2541 S 2542 2543 2549 2550 2551 2552 2553 2561 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 Cap, 10u, 20%, 50v, Electrolytic .
32PW6341/85 (continued) 3262 3265 3266 3269 3270 3271 3272 3273 3274 3275 3276 3277 3278 3279 3280 3283 3284 3285 3287 3289 3290 3291 3292 3293 3294 3295 3296 3401 3404 3412 3414 3415 3416 3417 3418 3420 3425 3427 3428 3430 3431 3440 3441 3442 3443 3445 3446 3451 3452 3453 3454 3455 3457 3458 3460 3461 3462 3463 3464 3466 3467 3468 3469 3470 3471 3472 3473 3474 3475 3478 3481 3482 3483 S 3484 S 3485 3486 3489 3490 3491 3492 3493 3494 3495 3497 3498 3499 3500 3501 3502 S 3503 3504 3505 Res, 100 ohm, 5%, 1/1
32PW6341/85 (continued) 4644 4645 4646 4648 4649 4691 4692 4694 4696 4910 4914 4915 4916 4917 4921 5001 5002 5201 5202 5203 5205 5206 5207 5208 5209 5210 5211 5212 5213 5214 5215 5216 5401 5402 5405 5408 5450 5451 5501 5511 5512 5531 5551 5552 5561 5562 5603 6001 6005 6203 6204 6205 6207 6209 6210 6211 6403 6406 6407 6408 6410 6411 6412 6441 6442 6443 6450 6451 6452 6453 6454 6455 6456 6457 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 Res, Zero ohm, "Chip" Jumpe
32PW6341/85 (continued) 9222 9223 9224 9225 9226 9227 9228 9229 9230 9231 9232 9233 9234 9235 9236 9237 9238 9239 9240 9241 9244 9245 9246 9247 9248 9249 9250 9251 9252 9253 9254 9255 9258 9259 9263 9264 9268 9269 9271 9272 9273 9274 9275 9276 9277 9278 9279 9280 9290 9294 9295 9296 9297 9298 9299 9402 9410 9417 9460 9466 9467 9469 9470 9473 9474 9475 9476 9477 9478 9479 9480 9481 9482 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 Wire Wire Wire Wire Wire Wi
33PT5441/85 - Manual no. 7661 Cabinet Parts Cabinet Parts 0002 Cabinet Front (part of Cabinet Front As sembly). . . . . . . . . . . . . . . . 0008 Cabinet Back . . . . . . . . . . . . . 0016 Power Button and Control Buttons Assemb ly. . . . . . . . . . . . . . . . . . . 0020 Degaussing Coil Holder (4 Used). . . . 0029 Plastic Facade (part of Cabinet Front A ssembly) . . . . . . . . . . . . . . . 0041 Light Guide. . . . . . . . . . . . . . 0050 Nameplate (part of Cabinet Front Assemb ly). . . . . . . . . . .
33PT5441/85 (continued) 3160 9181 Res, 100 ohm, 5%, 1/6W, Carbon Film. . Wire Jumper, 0.58MM. . . . . . . . . . 3198 011 01010 3198 036 90010 Top Control Panel Top Control Panel Main Chassis Main Chassis CBA Main Chassis . . . . . . . . . . . 1000 Tuner, V+U PLL . . . . . . . . . . 1002 S.A.W. Filter, 45MHz75, OFWM1971M. 1005 Connector, 3 Pin . . . . . . . . . 1137 MDIN Socket. . . . . . . . . . . . 1204 Connector, 7 Pin . . . . . . . . . 1205 Crystal Resonator, 24MHz576. . . . 1207 Connector, 7 Pin . .
33PT5441/85 (continued) 2562 2563 2564 2565 2566 2571 2572 2573 2601 2611 2615 2617 2620 2621 2623 2624 2625 2626 2627 2628 2629 2630 2691 2986 2987 2988 2989 2990 2992 2993 2994 2995 2996 2997 3003 3004 3005 3101 3103 3104 3105 3106 3121 3123 3124 3125 3126 3129 3130 3131 3132 3133 3134 3135 3167 3168 3169 3201 3202 3203 3204 3205 3206 3207 3208 3209 3210 3211 3212 3214 3215 3216 3218 3219 3220 3221 3222 3224 3225 3226 3227 3228 3229 3230 3231 3232 3233 3234 3235 3236 3237 3238 Cap, Cap, Cap, Cap, Cap, Ca
33PT5441/85 (continued) 3494 3495 3497 3498 3499 3500 3501 3502 S 3503 3504 3505 3507 S 3510 3511 3512 3513 3514 3515 3516 3517 3518 3519 3520 3521 3522 3524 3530 3531 3532 3533 3534 3537 3538 3541 3563 3565 3571 3572 3573 3574 3575 3576 3577 3578 3579 3601 3604 3605 3606 3607 3608 3609 3614 3616 3617 3618 3634 3635 3637 3681 3684 3685 3686 3687 3690 3691 3693 3694 3975 3985 3988 3989 3991 3992 3993 3994 3995 4000 4001 4002 4003 4006 4013 4015 4106 4107 4108 4116 4136 4209 4212 4221 Res, 150K, 5%, 1/16W, M
33PT5441/85 (continued) 6458 6459 6480 6481 6482 6483 6484 6486 6488 6489 6500 6511 6512 6514 6531 6532 6533 6534 6535 6536 6541 6551 6562 6563 6564 6565 6566 6571 6572 6573 6575 6602 6691 6692 6694 7200 7201 7203 7204 7207 7208 7209 7210 7404 7405 7406 7408 7410 7411 7451 7452 7453 7454 7455 7456 7481 7482 7483 7484 7511 7512 7513 7514 7531 7541 7561 7571 7573 7601 7603 7604 7605 7606 7990 7991 7992 8401 9002 9112 9113 9114 9116 9120 9121 9122 9123 9124 9125 9126 9128 9129 9138 Diode, Signal, BAS316. . .
33PT5441/85 (continued) 9483 9484 9485 9486 9487 9488 9489 9490 9491 9492 9502 9504 9505 9506 9507 9508 9509 9510 9514 9536 9537 9570 9573 9574 9575 9576 9577 9582 9583 9584 9585 9586 9587 9589 9590 9605 9631 9633 9637 9639 9642 9643 9653 9660 9661 9662 9663 9664 9665 9666 9683 9688 9689 9694 9695 9910 9911 9913 9914 9915 9920 9921 9924 9926 9927 9935 9936 9937 9939 9942 9943 9944 Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wire Wi
