Register your product and get support at 4131 series www.philips.
Contents 1 TV tour 12 Settings 3 1.1 Pause TV and recordings 1.2 EasyLink 3 2 Setting up 3 Connect devices 4 13 Channel installation 3.1 About connections 6 3.2 CAM with smart card - CI+ 7 3.3 Receiver - Set-Top Box 8 3.4 Home Theatre System - HTS 9 3.5 Blu-ray disc player 10 3.6 DVD player 11 3.7 Headphones 11 3.8 Game console 11 3.9 USB hard drive 12 3.10 USB flash drive 12 3.11 Photo camera 13 3.12 Camcorder -HDMI 13 3.
1 TV tour 1.1 Pause TV and recordings If you connect a USB Hard Drive, you can pause and record a broadcast from a digital TV channel. Pause your TV and answer that urgent phone call or simply take a break during a sports match, while the TV stores the broadcast on the USB Hard Drive. You can watch it again later. With a USB Hard Drive connected, you can also record digital broadcasts. You can record while you are watching a programme or schedule a recording of an upcoming programme.
2 Caution Setting up Read the safety instructions first before you use the TV. Wall mounting the TV requires special skills and should only be performed by qualified personnel. The TV wall mounting should meet safety standards according to the TVs weight. Also read the safety precautions before positioning the TV. TP Vision Europe B.V. bears no responsibility for improper mounting or any mounting that results in accident or injury. To read the instructions, in and care. 2.3 2.
consumption, unplug the power cable to save energy if you do not use the TV for a long period of time. For more information, in Help, see chapter Switching On and Off . 2.5 Antenna cable Insert the antenna plug firmly into the Antenna socket at the back of the TV. You can connect your own antenna or an antenna signal from an antenna distribution system. Use an IEC Coax 75 Ohm RF antenna connector. Use this antenna connection for DVB-T and DVB-C input signals. 2.
HDMI cable and do not use an HDMI cable longer than 5 m. 3 Connect devices 3.1 About connections Connectivity guide Copy protection Always connect a device to the TV with the highest quality connection available. Also, use good quality cables to ensure a good transfer of picture and sound. HDMI cables support HDCP (High-bandwidth Digital Content Protection). HDCP is a copy protection signal that prevents copying content from a DVD disc or Bluray Disc.
(Consumer Electronics Control) to communicate with the connected devices. Devices must support HDMI CEC and must be connected with an HDMI connection. and add an Audio L/R cable (mini-jack 3.5mm) to Audio In for sound, on the back of the TV. EasyLink setup The TV comes with EasyLink switched on. Make sure that all HDMI CEC settings are properly set up on the connected EasyLink devices. EasyLink might not work with devices from other brands.
3.2 CAM with smart card - CI+ CI+ This TV is ready for the CI+ Conditional Access. With CI+ you can watch premium HD programmes, like movies and sports, offered by digital TV operators in your region. These programmes are scrambled by the TV operator and descrambled with a prepaid CI+ module. Digital TV operators provide a CI+ module (Conditional Access Module - CAM) and an accompanying smart card, when you subscribe to their premium programmes. These programmes have a high level of copy protection.
Satellite tuner Connect the dish antenna cable to the Satellite receiver. Next to the antenna connection, add an HDMI cable to connect the device to the TV. Alternatively, you can use a SCART cable if the device has no HDMI connection. Audio to video synchronisation (sync) If the sound does not match the video on screen, you can set a delay on most Home Theatre Systems with a disc player to match the sound with the video.
For some Home Theatre Systems you might need to adjust the audio sync delay to synchronise the audio to the video. On the HTS, increase the delay value until there is a match between picture and sound. A delay value of 180ms may be required. Read the user manual of the HTS. With a delay value set up on the HTS, you need to switch off Audio Out Delay on the TV.
If the Blu-ray Disc player has EasyLink HDMI CEC, you can operate the player with the TV remote control. To adjust the volume… 1. Press , select Sound > Headphone volume and press OK. 2. Press the arrows (up) or (down) to adjust the value. 3. Press (left) repeatedly if necessary, to close the menu. 3.6 DVD player Use an HDMI cable to connect the DVD player to the TV. Alternatively, you can use a SCART cable, if the device has no HDMI connection. 3.
Warning Ideal setting The USB Hard Drive is formatted exclusively for this TV, you cannot use the stored recordings on another TV or PC. Do not copy or change recording files on the USB Hard Drive with any PC application. This will corrupt your recordings. When you format another USB Hard Drive, the content on the former will be lost. A USB Hard Drive installed on your TV will need reformatting for use with a computer.
To disconnect the USB flash drive, you can pull out the flash drive anytime. For more information on watching or playing content from a USB flash drive, in Help, see chapter Photos, videos and music. 3.11 Photo camera To view photos stored on your digital photo camera, you can connect the camera directly to the TV. With DVI to HDMI Use the USB connection on the TV to connect. Switch on the camera after you made the connection.
4 4.2 Switching On and Off Sleep timer With the Sleep timer, you can set the TV to switch to Standby automatically after a preset time. To set the Sleep timer… 4.1 1. Press , select General settings > Sleep timer and press OK. 2. With the slider bar you can set the time to up to 180 minutes in increments of 5 minutes. If set to 0 minutes, the Sleep Timer is switched off. You can always switch off your TV earlier or reset the time during the countdown. 3.
To open or close the Sources menu - the list of connected devices. 5 Remote control 2. Colour keys The buttons function follow the on-screen instructions. 5.1 Key overview 3. INFO To open or close programme infomation. Top 4. BACK To switch back to the previous channel you selected. To close a menu without changing a setting. 5. HOME To open or close the home menu. 6. EXIT To switch back to watching TV. 7. OPTIONS To open or close the Options menu. 8.
To open or close Text / Teletext. the - ends of the batteries line up correctly. 3. Reposition the battery door and slide it back until it clicks. 4. Remove the batteries if you are not using the remote control for a long time. 5.2 IR sensor (for 4031/5231 series TV) Safely dispose of your old batteries according to the end of use directions. For more information, in Help, see chapter Specifications > Environmental > End of use.
6 Filter a channel list Channels 6.1 You can filter a list with all channels. You can set the channel list to show only TV channels or only Radio stations. Switch channels To set a filter on a list with all channels… 1. While watching a TV channel, press LIST to open the channel list. 2. Press OPTIONS to open Option menu. 3. Select List, then you can select All, Favourites, Radio, and New channels. - To watch TV channels, press . The TV tunes to the TV channel you last watched.
rating for your child, the programme will be locked. To watch a locked programme you must enter the child lock code. The parental age rating is set for all channels. Remove channel from the favourites list To remove a channel from the favourites list, select the channel with , then press Unmark as favourite again to unmark as favourite. To set an age rating . . . 1. Press , select Child lock and press (right) to enter the menu. 2. Select Parental rating and press (right) to enter the menu. 3.
2. Select Languages and press (right) to enter the menu. 3. Select Primary audio language or Secondary audio language, and press OK. 4. Select the language you need and press OK. 5. Press (left) repeatedly if necessary, to close the menu. Preferred subtitle languages A digital broadcast can offer several subtitle languages for a programme. You can set a preferred primary and secondary subtitle language. If subtitles in one of these languages are available, the TV will show the subtitles you selected.
display correctly. Status - Text 2.5 To activate the Text 2.5 for more colours and better graphics. Select Status to view technical information on the channel (if it is analogue or digital) or a connected device you are watching. 6.4 Text setup Text / Teletext Text language Text pages Some digital TV broadcasters have several Text languages available. To set your primary and secondary Text language . . . To open Text/Teletext press TEXT, while you are watching TV channels.
7 Change day TV Guide The TV guide can show scheduled programmes for the upcoming days (maximum up to 8 days). 7.1 If the TV guide information comes from the broadcaster, you can press + to view the schedule of one of the next days. Press - to go back to the previous day. Alternatively, you can press OPTIONS and select Change day. Select Previous day, Today or Next day and press OK, to select the day of the schedule.
4. Select Close to close the list of reminders. Set a recording You can set a recording in the TV Guide. In the TV Guide, a programme set to be recorded is marked with . To see the recording list, press Recordings , a programme set to be recorded is marked with a (red dot) on the front of the programme name. To record a programme… 1. Press TV GUIDE and select a future or ongoing programme. 2. Press the colour key Record . To cancel a recording… 1.
What you need 1. Press TV GUIDE. 2. On the TV guide, select the channel and programme you wish to record. Press (Right) or (Left) to scroll through the programmes of a channel. 3. With the programme highlighted, press the colour key Record . The programme is scheduled for recording. A warning will show automatically when overlapping recordings are scheduled. If you plan to record a programme in your absence, remember to leave the TV switched to Standby and the USB Hard Drive switched on.
set the hours and minutes. 9. Select Schedule and press manual recording. To switch back to the live TV broadcast, press (Stop). OK to schedule the The recording will appear in the list of scheduled recordings and reminders. Replay Watch a recording Since the TV stores the broadcast you are watching, you can mostly replay the broadcast for a few seconds. To watch a recording… To replay a current broadcast… 1. Press TV GUIDE. 2. Press the colour key Recordings . 3.
9 Home menu 9.1 About the Home menu Channels This row contains all channles. Sources This row contains available sources in this TV. Utilities This row contains TV functions which are available for user. Quick settings This row contains settings which are available for user. 9.2 Open the Home menu To open the Home menu and open an item… 1 - Press Home . 2 - Select an item and press OK to open or start it. 3 - Press BACK to close the Home menu without starting anything.
clear. A game console can have a built-in Blu-ray Disc player and the type is set to Player because it is used as a disc player most of the time. For this kind of devices, you can temporarily switch to the ideal settings for gaming. Or alternatively, switch to the ideal settings for a connected computer. 10 Sources 10.1 Switch to a device You can only use the setting Game or Computer when you switch to a connected device in the Sources menu.
To show the progress bar when a video is playing, press INFO. Press again to hide the info. 11 Videos, photos and music Video options 11.1 During the video playback, press OPTIONS to… From a USB connection Subtitles Display the subtitles if available, select On, Off, or On during mute. You can view your photos or play your music and videos from a connected USB flash drive or USB Hard Drive. Audio language Play the audio language if available.
To view info on a photo (size, creation date, file path, etc.), select a photo and press INFO. Press again to hide the info. Play music How you open the list of your media files on TV depends on the type of device where the files are stored. See the chapters above. Slideshow with music To play a song on TV… You can watch a slideshow of your photos and listen to your music at the same time. You must start the usic before you start the photo slideshow.
12 12.2 Settings Picture 12.1 Picture style Quick settings Select a style Eco settings For easy picture adjustment, you can select a preset Picture Style. For more information, in Help, see chapter Eco settings. 1. While watching a TV channel, press . 2. Select Picture > Picture style, and select one of the styles in the list. 3. Press (left) repeatedly if necessary, to close the menu. Picture style The available Picture styles are ...
1. Press , select General settings and press (right) to enter the menu. 2. Select Location > Home and press OK. 3. Press (left) repeatedly if necessary, to close the menu. Advanced picture settings Game or computer When you connect a device, the TV recognizes its type and gives each device a correct type name. You can change the type name if you wish. If a correct type name for a device is set, the TV automatically switches to the ideal TV settings when you switch to this device in the Sources menu.
4. Press (left) repeatedly if necessary, to close the menu. Brightness Custom colour temperature With Brightness, you can set the level of brightness of the picture signal. Brightness is a setting intended for expert users. We recommend non-expert users to adjust the brightness of the picture with the Contrast setting. With Custom colour temperature, you can set a colour temperature yourself. To set a custom colour temperature, first select Custom in the Colour Temperature menu.
1. Press , select Picture and press (right) to enter the menu. 2. Select Advanced > Sharpness > Super resolution, and press (right) to enter the menu. 3. Select On or Off. 4. Press (left) repeatedly if necessary, to close the menu. the Picture format menu. 2. Select a format from the list and press OK. Screen edges With Screen edges, you can slightly enlarge the picture to hide distorted edges. To adjust the edges ... Noise reduction 1.
1. While watching a TV channel, press . 2. Select Sound and press (right) to enter the menu. 3. Select Sound style , and select the Sound Style you want to restore. 4. Press the colour key Restore style. The style is restored 5. Press (left) repeatedly if necessary, to close the menu. Advanced sound settings Auto volume levelling With Auto volume levelling, you can set the TV to automatically level out sudden volume differences.
Clear sound HDMI 1 - ARC With Clear sound, you improve the sound for speech. Ideal for news programmes. You can switch the speech improvement on or off. To switch on or off… 1. Press , select Sound and press (right) to enter the menu. 2. Select Advanced > HDMI 1 - ARC and press OK. 3. Select On or Off, then press OK. 4. Press (left) repeatedly if necessary, to close the menu. To switch on or off… 1. Press , select Sound and press (right) to enter the menu. 2.
4. Press (left) repeatedly if necessary, to close the menu. Screen off If you only listen to music, you can switch off the TV screen to save energy. Headphone volume To only switch off the TV screen… With Headphones volume, you can set the volume of a connected headphone separately. 1. Press , select Eco settings and press (right) to enter the menu. 2. Select Screen off. 3. Press (left) repeatedly if necessary, to close the menu. To adjust the volume… 1.
the menu. 3. Select Primary subtitle language or Secondary subtitle language, and press OK. 4. Select the language you need and press OK. 5. Press (left) repeatedly if necessary, to close the menu. Language preferences Audio language A digital broadcast can offer several audio languages (spoken languages) for a programme. You can set a preferred primary and secondary audio language. If audio in one of these languages is available, the TV will switch to the audio language.
To stop the automatic rotation of subpages. Clock - Dual screen / Full screen To show the TV channel and Text alongside each other. Date and time Automatic - T.O.P. overview To open T.O.P. Text. In some countries, digital broadcasts do not send UTC - Coordinated Universal Time information. The daylight saving change might be ignored and the TV might show an incorrect time. - Enlarge To enlarge the Text page for comfortable reading. - Reveal To unhide hidden information on a page.
during the countdown. 3. Press (left) repeatedly if necessary, to close the menu. Location If the TV is installed in a shop, you can set the TV to display an in store promotion banner. Picture style is set to Vivid automatically. Switch off timer is switched off. Switch off timer If the TV receives a TV signal but you don't press a key on the remote control during a 4 hour period, the TV switches off automatically to save energy.
12.7 Channel list copy Universal access For more information, in Help, see chapter Channel installation > Channel list copy. Switch on Satellite list copy With Universal access switched on, the TV is prepared for use for the deaf, hard of hearing, blind or partially sighted people. For more information, in Help, see chapter Channel installation > Channel list copy. Switch on 12.6 If you did not switch on Universal access during the installation, you can still switch it on in Universal access menu.
With Audio Description, a narrator's commentary is added to the normal audio. To switch on the commentary (if available)… menu. To switch on Audio Description… Speech 1. Press , select Universal access and press (right) to enter the menu. 2. Select Audio description and press (right) to enter the menu. 3. Select Audio description one step further 4. Select On and press OK. 5. Press (left) repeatedly if necessary, to close the menu.
4. Select Update channels and press OK. 5. Press BACK to close the menu. 13 Channel installation 13.1 Reinstall channels Antenna/cable installation Reinstall all channels Update channels You can reinstall all channels and leave all other TV settings untouched. Automatic channel update If a PIN code is set, you will need to enter this code before you can reinstall channels. If you receive digital channels, you can set the TV to automatically update the list with new channels.
values, the network ID or network frequency, enter these values when the TV asks for them during installation. search for channels, select Manual. Channel Number Conflicts Network frequency In some countries, different TV channels (broadcasters) might have the same channel number. While installing, the TV shows the list with channel number conflicts. You need to select which TV channel you want to install on a channel number with multiple TV channels.
To fine tune a channel, select Fine tune and press OK. You can fine tune the channel with or . If you want to store the channel found, select Done and press OK. Reception quality You can check the quality and signal strength of a digital channel. If you have your own antenna, you can reposition the antenna to try and improve the reception. To check the reception quality of a digital channel… - Store You can store the channel on the current channel number or as a new channel number.
To remove satellites . . . 1. Press , select Satellite installation and press OK. Enter your PIN code if necessary. 2. Select Search for satellite and press OK. 3. Select Remove satellite and press OK. The current satellites are shown. 4. Use the arrows keys to select the satellite you want to remove. 5. Press OK to mark a satellite to remove. Press OK again to unmark. 6. Select Remove, press OK and confirm. The satellites are removed. 7. Select Exit and press OK to close Remove satellite.
2. On the screen where you can start searching for satellites, select Settings and press OK. 3. Select the number of satellites you want to install or select one of the Unicable systems. When you select Unicable, you can choose the User Band Numbers and enter the User Band Frequencies for each tuner. 4. When you're done, select Next and press OK. 5. On the Settings menu, press the colour key Done to return to the screen to start searching for satellites.
channels. at the end of the installation when you finish. To switch off the message at start up . . . All satellite channels are gone 1. Press , select Satellite installation and press OK. Enter your PIN code if necessary. 2. Select Channel update message > Off. - If you use a Unicable system, make sure you assigned two unique user band numbers for both built-in tuners in the Unicable settings. It might be that another satellite receiver in your Unicable system is using the same user band number.
available. 4. Press (left) repeatedly if necessary, to close the menu. To installed TVs Depending on whether your TV is already installed or not, you must use a different method to upload a channel list. Copy a channel list To an already installed TV 1. Verify the country setting of the TV. (To verify this setting, see chapter Reinstall All Channels. Start this procedure until you reach the country setting. Press BACK to cancel the installation.) If the country is correct continue with step 2.
14 About open source license Software Acknowledgements and License Texts for any open source software used in this Philips TV. 14.1 This is a document describing the distribution of the source code used on the Philips TV, which fall either under the GNU General Public License (the GPL), or the GNU Lesser General Public License (the LGPL), or any other open source license. Instructions to obtain source code for this software can be found in the user manual.
libboost (1.51) MTD utility (1.5.0) Boost provides free peer-reviewed portable C++ source libraries, and emphasize libraries that work well with the C++ Standard Library. MTD subsystem (stands for Memory Technology Devices) provides an abstraction layer for raw flash devices. It makes it possible to use the same API when working with different flash types and technologies, e.g. NAND, OneNAND, NOR, AG-AND, ECC'd NOR, etc.
power consumption of the television operating 4 hours per day for 365 days. The actual energy consumption depends on how the television is used. 15 Specifications ** When the TV is turned off with the remote control and no function is active. 15.1 Environmental End of use European Energy Label Disposal of your old product and batteries The European Energy Label informs you on the energy efficiency class of this product.
- Mains power : AC 220-240V +/-10% - Ambient temperature : 5°C to 35°C - Power saving features : Eco mode, Picture mute (for radio), Auto switch-off timer, Eco settings menu. 15.5 Display input resolution For PHx series TV For power consumption information, see chapter Product Fiche. Video formats The power rating stated on the product typeplate is the power consumption for this product during normal household use (IEC 62087 Ed.2).
15.6 TV Rear Dimensions and Weights - HDMI 1 ARC: HDMI Audio Return Channel - HDMI 2 - SERV. U: Service port - SCART (RGB/CVBS): SCART adaptor - AUDIO IN (DVI): Stereo 3.5mm mini-jack - DIGITAL AUDIO OUT: SPDIF - TV ANTENNA: 75 ohm coaxial (IEC) 4131 series TV 32Pxx4131 - without TV stand: Width 726.5 mm - Height 425.4 mm - Depth 79.2 mm - Weight ± 4.66 kg TV Side - CI: Common Interface - USB - Headphones: Stereo 3.5mm mini-jack - with TV stand: Width 726.5 mm - Height 479.2 mm - Depth 170.
The TV needs to be checked. If you do not notice the flickering, the remote control might be broken or its batteries are low. This method of checking the remote control is not possible with remote controls which are wirelessly paired with the TV. 16 Help and support 16.
direction or moving devices away from the TV. - If reception on only one channel is poor, fine-tune this channel with Manual Installation. Connections HDMI Poor picture from a device Picture does not fit the screen - Note that HDCP (High-bandwidth Digital Content Protection) support can delay the time taken for a TV to display content from an HDMI device. - If the TV does not recognise the HDMI device and no picture is displayed, switch the source from one device to another and back again.
16.5 Consumer care / Repair For support and repair, call the Consumer Care hotline in your country. Find the telephone number in the printed documentation that came with the TV. Or consult our website www.philips.com/support . TV model number and serial number You might be asked to provide the TV product model number and serial number. Find these numbers on the packaging label or on the type label on the back or bottom of the TV. Warning Do not attemp to repair the TV yourself.
17 Risk of injury or damage to the TV Safety and care - Two people are required to lift and carry a TV that weighs more than 25 kg or 55 lbs. 17.1 - If you mount the TV on a stand, only use the supplied stand. Secure the stand to the TV tightly. Place the TV on a flat, level surface that can support the weight of the TV and the stand. Safety Important - When wall mounted, ensure that the wall mount can safely bear the weight of the TV set.
Lightning storms Disconnect the TV from the power outlet and antenna before lightning storms. During lightning storms, never touch any part of the TV, power cord or antenna cable. Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time. Low temperatures If the TV is transported in temperatures below 5°C or 41°F, unpack the TV and wait until the TV temperature reaches room temperature before connecting the TV to the power outlet.
procedures not recommended or authorised in this manual, shall void the warranty. 18 Terms of use, copyrights and licenses Pixel characteristics This LCD/LED product has a high number of colour pixels. Although it has effective pixels of 99.999% or more, black dots or bright points of light (red, green or blue) may appear constantly on the screen. This is a structural property of the display (within common industry standards) and is not a malfunction. 18.1 CE compliance Hereby, TP Vision Europe B.V.
Dolby Digital Plus Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. DTS 2.0 + Digital Out ™ For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS 2.0+Digital Out is a trademark of DTS, Inc. © DTS, Inc. All Rights Reserved.
Index Contrast, Gamma 31 Contrast, Video Contrast 31 A Antenna connection 5 Antenna, Manual Installation 43 Audio commentary 39 Audio Description 39 Audio Language 19 Audio Language, Primary 19 Audio Language, Secondary 19 Audio Out - Optical, tips 7 Audio Out Delay 9 Audio Out Format 10 Audio Out Levelling 10 Audio Out Offset 10 Audio Out Settings 9 Audio to Video Sync 9 Auto Volume Levelling 33 Automatic Channel Update 41 Automatic switch off 14 D Digital Text 20 Disposal of TV or batteries 50 DVB (Digi
Photo camera, connect 13 Photos, videos and music 27 Picture Format, advanced 32 Picture Format, basic 32 Picture Style 29 Picture, Backlight Contrast 30 Picture, Colour 30 Picture, Sharpness 30 Placement, TV placement 4 Placement, viewing distance 4 Power connection 4 Problems 53 Problems, Channels 53 Problems, Connection, HDMI 54 Problems, Connection, USB 54 Problems, Picture 53 Problems, Remote control 53 Problems, Sound 54 Product Fiche 50 Treble 33 TV Guide 21 TV Guide, Reminder 21 TV Installation 41
Powered by TCPDF (www.tcpdf.
