Register your product and get support at 4100 series www.philips.
Contents 1 Your new TV 12 Pause TV 3 1.1 Pause TV and recordings 1.2 EasyLink 3 2 Setting up 12.1 Pause TV 4 4 14 Settings 4.1 On or Standby (For 4100, 4200 TV models) 16 Software 14 15 17.1 Troubleshooting 51 17.2 Register 52 17.3 Help 52 17.4 Online help 52 17.5 Consumer Care / Repair 18 Safety and care 17 20 18.1 Safety 54 18.2 Screen care Index 30 32 9.1 Sources list 32 9.2 From standby 32 9.3 EasyLink 32 33 10.1 Sleep timer 33 10.2 Clock 33 10.
1 Your new TV 1.1 Pause TV and recordings If you connect a USB Hard Drive, you can pause and record a broadcast from a digital TV channel. Pause your TV and answer that urgent phone call or simply take a break during a sports match, while the TV stores the broadcast on the USB Hard Drive. You can start watching again later. 1.2 EasyLink With EasyLink you can operate a connected device, like a Bluray Disc player, with the remote control of the TV.
M4 (Minimum 10 mm, Maximum 14 mm) - 32PHT4100/60 - VESA MIS-F 100x100, M4 (Minimum 12 mm, Maximum 16 mm) - 40Pxx4100 - VESA MIS-F 200x200, M4 (Minimum 12 mm, Maximum 16 mm) - 48Pxx4100 - VESA MIS-F 200x200, M6 (Minimum 12 mm, Maximum 16 mm) 2 Setting up 2.1 Read safety - 32Pxx4200 - VESA MIS-F 100x100, M4 (Minimum 10 mm, Maximum 14 mm) - 40Pxx4200 - VESA MIS-F 200x200, M4 (Minimum 12 mm, Maximum 16 mm) Read the safety instructions first before you use the TV. In Help, go to Safety and care > Safety.
Although this TV has a very low standby power consumption, unplug the power cable to save energy if you do not use the TV for a long period of time. 2.5 Antenna cable Insert the antenna plug firmly into the ANTENNA socket at the back of the TV. You can connect your own antenna or an antenna signal from an antenna distribution system. Use an IEC Coax 75 Ohm RF antenna connector. Use this antenna connection for DVB-T and DVB-C input signals. 2.
3 Connections 3.1 Tips on connections EasyLink HDMI CEC Connectivity guide If your devices are connected with HDMI and have EasyLink, you can operate them with the TV remote control. EasyLink HDMI CEC must be switched On on the TV and the connected device. Always connect a device to the TV with the highest quality connection available. Also, use good quality cables to ensure a good transfer of picture and sound.
EasyLink setup The TV comes with EasyLink switched on. Make sure that all HDMI CEC settings are properly set up on the connected EasyLink devices. EasyLink might not work with devices from other brands. HDMI CEC on other brands The HDMI CEC functionality has different names on different brands. Some examples are: Anynet, Aquos Link, Bravia Theatre Sync, Kuro Link, Simplink and Viera Link. Not all brands are fully compatible with EasyLink.
Contact a digital TV broadcaster for more information on terms and conditions. EasyLink settings The TV comes with all EasyLink settings switched on. You can switch off any EasyLink setting independently. EasyLink CAM To switch off EasyLink completely . . . 1. Press and select Setup and press OK. 2. Select TV settings > General settings > EasyLink. 3. Select EasyLink. 4. Select Off and press OK. 5. Press , repeatedly if necessary, to close the menu.
Switch off this automatic timer, if you only use the remote control of the Set-top box. Do this to prevent the TV from switching off automatically after a 4 hour period without a key press on the remote control of the TV. 3.6 Home Theatre System - HTS Connect HTS To switch off the Switch off timer, press and select Setup and press OK. Select TV settings > General settings > Auto switch off and set the slider bar to Off. Use an HDMI cable to connect a Home Theatre System (HTS) to the TV.
a TV channel or connected player to the Home Theatre System. If you have a Home Theatre System without multichannel sound processing, select Stereo. Audio Out settings Audio Out delay To set the Audio Out format . . . With a Home Theatre System (HTS) connected to the TV, the picture on TV and the sound from the HTS should be synchronised. 1. Press and select Setup and press OK. 2. Select TV settings > Sound > Advanced > Audio out format. 3. Select Multichannel or Stereo. 4.
3.7 HDMI Blu-ray Disc player For best quality, connect the game console with an High speed HDMI cable to the TV Use a High speed HDMI cable to connect the Blu-ray Disc player to the TV. If the Blu-ray Disc player has EasyLink HDMI CEC, you can operate the player with the TV remote control. 3.10 USB Hard Drive What you need 3.8 If you connect a USB Hard Drive, you can pause or record a TV broadcast. The TV broadcast must be a digital broadcast (DVB broadcast or similar).
To stop watching the USB flash drive content, press EXIT or select another activity. To disconnect the USB flash drive, you can pull out the flash drive anytime. Installation Before you can pause or record a broadcast, you must connect and format a USB Hard Drive. 1. Connect the USB Hard Drive to one of the USB connections on the TV. Do not connect another USB device to the other USB ports when formatting. 3.12 Camcorder HDMI For best quality, use an HDMI cable to connect the camcorder to the TV. 2.
ideal TV watching or gaming setting. To set the TV to the ideal setting manually . . . 1. Press and select Setup and press OK. 2. Select TV settings > Picture > Advanced > Game or compter and press OK. 3. Select Game (for gaming) or select Computer (for watching a movie) and press OK. 4. Press , repeatedly if necessary, to close the menu. Remember to set the Game or computer setting back to Computer when you stop playing the game. 3.
4 Switch on 4.1 On or Standby (For 4100, 4200 TV models) Make sure you plugged in the mains power on the back of the TV before you switch on the TV. If the red indicator light is off, press the Joystick on the right side or on the back of the TV to put the TV in standby - the red indicator will light up. With the TV in standby, press onon the remote control to switch the TV on. Switch to standby To switch the TV to standby, press on the remote control.
5 To open or close programme infomation. Remote control 4. BACK To switch back to the previous channel you selected. To close a menu without changing a setting. 5.1 5. HOME To open or close the home menu. Key overview (For 4000, 4100, 4200, 5210 TV models) 6. EXIT To switch back to watching TV. 7. OPTIONS To open or close the Options menu. Top 8. OK key To confirm a selection or setting. 9. Arrow / navigation keys To navigate up, down, left or right. 10.
5.2 IR sensor The TV can receive commands from a remote control that uses IR (infrared) to send commands. If you use such a remote control, always make sure you point the remote control at the infrared sensor on the front of the TV. 5.3 Batteries 1. Slide the battery door in the direction shown by the arrow. 2. Replace the old batteries with 2 type AAA-LR03-1.5V batteries. Make sure the + and the - ends of the batteries line up correctly. 3. Reposition the battery door. 4. Slide it back until it clicks.
are installed during installation. Switch to a radio channel just like you switch to a TV channel. 6 TV channels 6.1 Channel list Watching TV channels View all channel list 1. While watching a TV channel, press LIST to open the channel list. 2. Press OPTIONS to open Option menu. 3. Select List, then you can select All, Favourites, Radio, and New channels. Switch channels (For 4000, 4100, 4200, 5210 TV models) To watch TV channels, press . The TV tunes to the TV channel you last watched.
1. Press and select Setup and press OK. 2. Select Channel settings > Child lock > Parental rating and press OK. 3. Enter a 4-digit Child lock code. Enter a 4-digit Child lock code and confirm. Now you can set an age rating. 4. Set the age and press OK. 5. Press , repeatedly if necessary, to close the menu. 6. To switch off the parental age rating, select None as age setting. computer. - 4:3 Display the classic 4:3 format.
occurences of this word. Text setup 1. Open a Text page and press OK. 2. Select a word or number with the arrow keys. 3. Press OK again to jump immediately to the next occurence of this word or number. 4. Press OK again to jump to the subsequent occurence. 5. To stop searching, press (up) until nothing is selected. Text language Some digital TV broadcasters have several Text languages available. To set your primary and secondary Text language . . . 1. Press and select Setup and press OK. 2.
If none of the preferred subtitle languages are available, you can select another subtitle language which is available. impaired Some digital TV channels broadcast special audio and subtitles adapted for people who are hearing or visually impaired. To set the primary and secondary subtitle language . . . 1. Press and select Setup and press OK. 2. Select Channel settings and select Languages. 3. Select Primary subtitle language or Secondary subtitle language and press OK. 4.
In certain countries, the Automatic channel update is done while watching TV or any moment when the TV is in standby. Channel list copy New channels Channel list copy is intended for dealers and expert users. In some countries, Channel list copy is only availble for copying satellite channels. Introduction New channels added with the automatic channel update are easy to find in the channel list New. The same new channels are also stored in the All or Radio channel list.
3. To start the channel list upload, press and select Setup and press OK. 4. Select TV settings > General settings > Copy channel list > Copy to TV and press OK. You might be asked to enter the Child lock code of this TV. 5. The TV notifies you if the channel list is copied to the TV successfully. Unplug the USB memory device. It might be necessary to adjust the scanning (full or quick scan) or enter a specific symbol rate in the Settings menu while installing.
To set up the TV system, select System and press OK. Select your country or the part of the world where you are now. - Search channel To find a channel, select Search channel and press OK. Select Search and press OK. You can also enter a frequency yourself. If the reception is poor, press Search again. If you want to store the channel, select Done and press OK. - Fine tune To fine tune a channel, select Fine tune and press OK. You can fine tune the channel with or .
7 Channel list options Satellite channels (For PxK models) To view the channel list options on the current channel . . . 7.1 1. With the All channels list on screen, select a channel and press OPTIONS . 2. Select the option you want and press OK. Watching satellite channels Available options for satellite channels . . . - Only for TVs with a built-in satellite tuner. - Satellite Filter the channel list to only show the channels of a specific satellite or show the channels of all satellites.
one for satellite channels. Lock a channel You can lock a channel to prevent children from watching it. To watch a locked channel you need to enter the Child lock code. You cannot lock programmes from connected devices. Set up your favourites list To compose a list of your favourite channels . . . 1. While watching a channel, press LIST to open the channel list. 2. Select the Favourites list. 3. The TV will ask you to start adding channels immediately. Press OK.
code and then enter the new code twice. Settings and press OK. Go to step 4b. The new code is set. 4b - In the Settings menu, select the exact number of satellites you want to install. Or, if you use a Unicable setup, select Unicable for 1 satellite or Unicable for 2 satellites according the number of satellites you want to install for Unicable. Select the setting you want and press OK. 4c - If the exact number of satellites is set or you completed the Unicable settings, select Search and press OK.
If you notice some missing channels after a Unicable installation, another installation might have been done at the same moment on the Unicable system. Do the installation again to install the missing channels. 4. Select Add and press OK. The TV will search for new satellites. 5. If the TV has found one or more satellites, select Install and press OK. The TV installs the channels of the found satellites. 6. To store the channels and radio stations, select Finish and press OK.
Automatic update option. 3. With the arrow keys, select the satellite you do not wish to update. Press OK to unmark the satellite. 4. Select Done and press OK to close the menu. Audio effect Some audio commentary can hold extra audio effects, like stereo or fading sound. The TV will not update the channels from satellite you marked. To switch on Audio effects (if available) . . . 1. Press and select Setup and press OK. 2.
7.6 Problems with satellites The TV cannot find the satellites I want or the TV installs the same satellite twice - Make sure that the correct number of satellites is set in Settings at the start of the installation. You can set the TV to search for One, Two or 3/4 satellites. A dual head LNB cannot find a second satellite - If the TV finds one satellite but cannot find a second one, turn the dish a few degrees. Align the dish to get the strongest signal on the first satellite.
8 Change day TV guide The TV guide can show scheduled programmes for the upcoming days (maximum up to 8 days). 8.1 If the TV guide information comes from the broadcaster, you can press + to view the schedule of one of the next days. Press to go back to the previous day. Alternatively, you can press OPTIONS and select Change day. Select Previous day, Today or Next day and press OK, to select the day of the schedule.
9 9.3 Sources EasyLink With EasyLink you can operate a connected device with the TV remote control. EasyLink uses HDMI CEC to communicate with the connected devices. Devices must support HDMI CEC and must be connected with an HDMI connection. 9.1 Sources list In the list of connections - the Source menu - you can find the devices connected to the TV.From this Source menu, you can switch to a device. Sources menu To open the Sources menu, press SOURCES .
off and set the slider bar to 0 (Off). 3. Press , repeatedly if necessary, to close the menu. 10 Timers and clock 10.1 Sleep timer With the sleep timer, you can set the TV to switch to standby automatically after a preset time. To set the sleep timer . . . 1. Press and select Setup and press OK. 2. Select TV settings > General settings > Sleep timer. With the slider bar you can set the time to up to 180 minutes in increments of 5 minutes. If set to 0 minutes, the sleep timer is switched off.
- Repeat, Play once View the pictures repeatedly or once only. 11 Your photos, videos and music - Shuffle off, Shuffle on View the pictures in sequential order, or at random. - Rotate image Rotate photo. 11.1 From a USB connection - Show info Display the picture name, date, size and next picture in the slide show. What you need To close Browse USB, press and select another activity. You can view your photos or play your music and videos from a connected USB flash drive or USB Hard Drive.
To close Browse USB, press and select another activity.
12 Pause TV 12.1 Pause TV You can pause a TV broadcast and resume watching it later. Only digital TV channels can be paused. You must connect a USB Hard Drive to buffer the broadcast. You can pause a broadcast for a maximum time span of 90 minutes. Pause or resume a broadcast To pause a broadcast, press (Pause). A progress bar appears briefly on screen. To call up the progress bar, press (Pause) again. To resume watching, press (Play).
USB Hard Drive switched on. 13 Recording List of recordings 13.1 What you need To view the list of recordings and scheduled recordings, press , select Recordings and press OK. To record a TV programme you need . . .
14 Picture settings Settings Backlight contrast 14.1 With Backlight contrast, you can adjust the brightness of the display backlight. Picture To adjust the level . . . 1. Press and select Setup and press OK. 2. Select TV settings > Picture > Backlight contrast. 3. Press (right) and adjust the value with (up) or (down). 4. Press , repeatedly if necessary, to close the menu. Picture style For easy picture adjustment, you can select a preset setting with Picture style. 1.
point and BL is black level.) 5. Press OK to confirm a setting. You can also select one of the presets in this menu. 6. Press , repeatedly if necessary, to close the menu. MPEG artefact reduction With MPEG artefact reduction , you can smoothen the digital transitions in the picture. MPEG artefacts are mostly visible as small blocks or jagged edges in images. To reduce the MPEG artefact . . . 1. Press and select Setup and press OK. 2. Select TV settings > Picture > MPEG artefact reduction . 3.
setting and adjust it. 4. Press to close the menu to store your setting. 14.3 Format and edges To return to the original Sound style values . . . 1. Press and select Setup and press OK. 2. Select TV settings > Sound > Restore style. Picture format If black bars appear on top and bottom or on both sides of the picture, you can adjust the picture format to a format that fills the screen. To change the picture format . . . 1. While watching a TV channel, press to open the Picture format menu. 2.
and press OK. 3. Press (up) or (down) to adjust the volume. 4. Press , repeatedly if necessary, to close the menu. menu. Clear sound With Clear sound, you improve the sound for speech. Ideal for news programmes. You can switch the speech improvement on or off. Advanced sound settings Auto volume levelling To switch on or off . . . 1. Press and select Setup and press OK. 2. Select TV settings > Sound > Advanced > Clear sound. 3. Press (right) and select On or Off. 4.
14.5 Speakers Ambilight (For 6300 TV models) Home Theatre System You can send the TV sound to a connected audio device - a Home Theatre System or audio system. Ambilight style You can select where you want to hear the TV sound and how you want to control it. - If you select Off, you permanently switch off the TV speakers. - If you select TV speakers, the TV speakers are always on. Ambilight can have a dynamic mode or a static mode. With Dynamic mode, the TV follows the colours of the image on screen.
Dynamic speed With Dynamic, you can set the speed at which Ambilight responds to the images on screen. Adjust the speed between Relaxed or Dynamic. The Ambilight mode must be set to Dynamic before you can adjust Dynamic speed. To adjust the speed . . . 1. Press and select Setup and press OK. 2. Select TV settings > Ambilight > Dynamic. 3. Press (right) and adjust the value with (up) or (down). 4. Press , repeatedly if necessary, to close the menu.
15 European energy label Specifications The European Energy Label informs you on the energy efficiency class of this product. The greener the energy efficiency class of this product is, the lower the energy it consumes. On the label, you can find the energy efficiency class, the average power consumption of this product in use and the average energy consumption for 1 year. You can also find the power consumption values for this product on the Philips website for your country at www.philips.com/TV 15.
15.2 Display resolutions Reception for PxK models Computer formats - HDMI (Resolution - refresh rate) 640 x 480 - 60 Hz 800 x 600 - 60 Hz 1024 x 768 - 60 Hz 1280 X 720 - 60 Hz 1280 X 768 - 60 Hz 1280 x 1024 - 60 Hz 1360 x 768 - 60 Hz 1680 x 1050 - 60 Hz* 1920 x 1080 - 60 Hz* - Aerial input : 75 ohm coaxial (IEC75) - Tuner bands : Hyperband, S-Channel, UHF, VHF - DVB : DVB-T (terrestrial, antenna) COFDM 2K/8K, DVB-T2 : only for TV types '. . .
15.5 - Weight ± 12.2 kg Dimensions and weights - with TV stand: Width 1081.8 mm - Height 662.7 mm - Depth 255.96 mm - Weight ± 12.8 kg 22Pxx4000 40Pxx6300 - without TV stand: Width 445.1 mm - Height 269.7 mm - Depth 45.7 mm - Weight ± 2.67 kg - without TV stand: Width 911 mm - Height 528.3 mm - Depth 47.7 mm Weight ± 9.26 kg - with TV stand: Width 445.1 mm - Height 279.3 mm - Depth 112 mm Weight ± 2.7 kg - with TV stand: Width 911 mm - Height 591.6 mm - Depth 241.
15.6 15.8 Connectivity for Pxx4100, Pxx4200 Multimedia Note: Multimedia file names must not exceed 128 characters. For PxK4100, PxK4200 Supported multimedia connections TV Rear - USB 2.0 (FAT / FAT 32 / NTFS): only connect USB devices that consume 500 mA of power or less. - HDMI 1 ARC: HDMI Audio Return Channel - HDMI 2 - SERV. U: Service port - SCART (RGB/CVBS): SCART adaptor - AUDIO IN (DVI/VGA): Stereo 3.
16 16.2 Software Software version To view the current TV software version . . . 16.1 1. Press and select Setup and press OK. 2. Select Software settings and press OK. 3. Select Current software info and see Release Version. 4. Press , repeatedly if necessary, to close the menu. Software update Update from USB It might be necessary to update the TV software. You need a computer and a USB memory device to upload the software on the TV. Use a USB memory device with 256MB free space.
statutory rights regarding any product(s) you purchased. It only applies to this source code made available to you. zlib (1.2.7) A massively spiffy yet delicately unobtrusive compression library Source: www.zlib.net libsqlite3 (3.7.14) SQLite is a C library that implements an SQL database engine. Programs that link with the SQLite library can have SQL database access without running a separate RDBMS process. libdirectfb (1.4.
libscew The aim of SCEW is to provide an easy interface around the XML Expat parser, as well as a simple interface for creating new XML documents. It provides functions to load and access XML elements without the need to create Expat event handling routines every time you want to load a new XML document. SCEW is freely available for download under the terms of the GNU Lesser General Public License v2.1 (LGPL). Source: http://www.nongnu.org/scew/ libexpat Expat is an XML parser library written in C.
17 Philips startup screen Troubleshooting and support When the TV is in standby, a Philips startup screen is displayed, then the TV returns to standby mode. This is normal behaviour. When the TV is disconnected and reconnected to the power supply, the startup screen is displayed at the next startup. To switch on the TV from standby, press on the remote control or the TV. 17.1 Troubleshooting The standby light keeps on blinking Disconnect the power cable from the power outlet.
EasyLink does not work Make sure that Location is set to Home. - Make sure that your HDMI devices are HDMI-CEC compatible. EasyLink features only work with devices that are HDMI-CEC compatible. Picture does not fit the screen Change to a different picture format. Press . No volume icon shown Picture format keeps changing with different - When a HDMI-CEC audio device is connected this behaviour is normal. channels Select a non 'Auto' picture format.
On the support site you can find your country's telephone number to contact us as well as answers to frequently asked questions (FAQs). In some countries, you can chat with one of our colaborators and ask your question directly or send a question by email. You can download new TV software or the manual to read on your computer. 17.5 Consumer Care / Repair For support and repair, call the Consumer Care hotline in your country. Find the telephone number in the printed documentation that came with the TV.
18 Risk of injury or damage to the TV Safety and care - Two people are required to lift and carry a TV that weighs more than 25 kg or 55 lbs. 18.1 - If you mount the TV on a stand, only use the supplied stand. Secure the stand to the TV tightly. Place the TV on a flat, level surface that can support the weight of the TV and the stand. Safety Important - When wall mounted, ensure that the wall mount can safely bear the weight of the TV set.
Lightning storms Disconnect the TV from the power outlet and antenna before lightning storms. During lightning storms, never touch any part of the TV, power cord or antenna cable. Risk of hearing damage Avoid using earphones or headphones at high volumes or for prolonged periods of time.
property of the display (within common industry standards) and is not a malfunction. CE compliance This product is in compliance with the essential requirements and other relevant provisions of Directives 2006/95/EC (Low Voltage), 2004/108/EC (EMC) and 2011/65/EU (ROHS). Compliance with EMF TP Vision Europe B.V. manufactures and sells many products targeted at consumers which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals.
MHEG software The copyright in MHEG software (the Software) comprised in this television (this product) and included to enable you to use interactive television features is owned by S&T CLIENT SYSTEMS LIMITED (the Owner). You are permitted to use the Software only in conjunction with this product. Kensington Kensington and Micro Saver are registered US trademarks of ACCO World Corporation with issued registrations and pending applications in other countries throughout the world.
Index 58
Powered by TCPDF (www.tcpdf.
