Register your product and get support at www.philips.com/support 32PFL4507 26PFL4507 22PFL4507 EN User Manual ES Manual del Usuario FR Manuel d’Utilisation EN: For further assistance, call the customer support service in your country. • To obtain assistance, contact Philips Customer Care Center; In the U.S.A., Canada, Puerto Rico, or the U.S. Virgin Islands 1 866 309 0843 México D.F.
Contents 1 Notice 5 2 Important 6 6 6 6 Positioning the TV Regulatory notices Environmental care 3 Get started Features Supplied accessories Symbols used in this User Manual Attaching the base Mounting the unit on your furniture Managing cables Installing the remote control batteries Remote control Control panel Terminals Connecting the antenna or the cable Plugging in the AC power cord Initial setup 7 7 7 7 8 8 8 8 9 10 10 11 11 12 4 Use your TV 14 14 14 14 15 15 15 15 16 16 17 5 Use more
Return your Product Registration Card or visit at http://www.productrecords.com/philips/ today to get the very most from your purchase. Registering your model with Philips makes you eligible for all of the valuable benefits listed below, so don't miss out. Complete and return your Product Registration Card at once or visit at www.philips.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
1 Notice Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. P&F USA reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this User Manual is believed adequate for the intended use of the system. If the product or its individual modules or procedures are used for purposes other than those specified herein, confirmation of their validity and suitability must be obtained.
2 Important Environmental care Positioning the TV • • • • • • • • • • • • Large screen TVs are heavy. 2 people are required to carry and handle a large screen TV. Make sure to hold the upper and bottom frames of the unit firmly as illustrated. Install the unit in a horizontal and stable position. Do not install the unit in direct sunlight or in a place subject to dust or strong vibration. Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
3 Get started Supplied accessories User Manual Features • DTV /Analog TV / CATV • Information display Quick Start guide Quick • Autoprogram Remote Control and batteries (AAA, 1.5V x 2) This unit automatically scans and memorizes channels available in your area, eliminating difficult setup procedures. • TV base and screws Screws packed with this unit: Child lock Model This feature allows you to block children’s access to inappropriate programs.
Attaching the base Managing cables You must attach the base to the unit to have it as a table top unit. Be sure the front and rear of the base match the proper direction. For large screen TVs, at least 2 people are required for these steps. Route your antenna cable and all other cables through the cable management tie at the back of the TV. The holder helps keep your cables tidy and easily manageable. 1 1 1 Attach the cable management tie as illustrated below.
Remote control a b p o c * n m d e f g l h k j *This button does not function on this unit. i a (POWER-ON / STANDBY-ON) Press to turn the unit On and go into Standby mode. To completely Turn Off the unit, you must unplug the AC power cord. b SOURCE Toggle and select connected devices. c FORMAT Selects a picture format. d SAP Digital Mode (DTV) : Press to select the Audio language. Analog Mode (Analog TV) : Press to select the Audio mode. e FREEZE Press to freeze screen image.
a VOL ◄/► Control panel a b c d Touch to adjust volume down (◄) / up (►) or to move left (◄) / right (►) when selecting menu items. b MENU Touch to display the main menu. c SOURCE Touch to select the connected devices. d CH ▲/▼ Touch to select channels or to move up (▲) / down (▼) when selecting menu items. e (POWER-ON / STANDBY-ON) Touch to Turn the unit On and go into Standby mode. To completely Turn Off the unit, you must unplug the AC power cord.
Connecting the antenna or the cable Be sure your antenna or other device is connected properly before plugging in the AC power cord. Connecting a set-top box, Blu-ray disc / DVD recorder via composite connectors and Analog Audio Do not place your recorder too close to the screen because some recorders can be susceptible to signals. If you connect to an antenna through RF cable Any DTV programs that are broadcasted in your area can be received for free through an antenna connection.
These operations are accessible by remote control. Some may also be accessible by control panel on the main unit. 4 Use ▲▼ to select the desired location setting, then press OK. Home is ENERGY STAR® qualified setting. Initial setup Initial setup Retail Location Home is recommended for normal home use and is ENERGY STAR qualified. In the Retail Store mode, all settings are fixed.
Note •• If you are not receiving a signal from your cable service, contact the Cable provider. •• If you press or MENU / EXIT during autoprogram, this setup of TV channels will be canceled. •• The initial autoprogram function can be executed for either Antenna or Cable only once. When you change the connection (Antenna / Cable), set Autoprogram again. ➠ p.20 •• If there is no signal Input from the antenna terminal and no operation for several seconds after you Turn On the unit, helpful hints appears.
4 Use your TV Switching channels Switching on your TV and putting it in standby mode To Turn Power On or to Turn Standby On • Touch or press . on the front panel or the remote control. Note •• Energy consumption contributes to air and water pollution. When the AC power cord is plugged in, your TV consumes energy. Your TV has very low standby power consumption.
Watching channels from an external device Sleep timer Switching Each Input Mode can easily switch with the remote control between TV (DTV or Analog TV) and external devices when they are connected to the unit. Sleep Timer can set the unit to go into Standby mode after an incremental period of time. 1 Turn On a set-top box or the connected device. • The picture from your set-top box or the connected device might appear automatically on the TV screen.
For 16:9 video signal Switching audio mode Normal Movie expand Full can also be selected after Wide if an HDMI device is selected. This picture format similarly displays like Normal. Digital TV operation Full (HDMI device only) 1 Press SAP to display the currently selected language and the number of available languages. 11.1 English 1/3 2 Press SAP repeatedly to cycle through the available audio languages.
TV screen information You can display the currently selected channel or other information such as the aspect ratio on the TV screen. In the Digital mode, the detailed broadcasting information for the current off the air channel such as program title and program guides are displayed. 1 Press INFO. Digital TV operation a b c A Day of Memories d 11.
5 Use more of your TV This section describes the overview of the main menu displayed when you press MENU / EXIT. The main menu consists of the function setting items below. Displaying the main menu 1 2 Press MENU / EXIT to display the main menu. Use ▲▼ to select the desired menu and an item, then press OK or use ▲▼◄► to determine the setting. Picture ➠ p.19 Adjusting the picture mode or customize the picture quality as your preference. Sound ➠ p.
*You can set a particular about picture quality in Advanced settings. Picture Before you begin: You must set Home in Location. ➠ p.27 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode. 1 Press MENU / EXIT and use ▲▼ to select Picture then press OK.
Sound Setup Before you begin: You must set Home in Location. ➠ p.27 Otherwise, personalized picture and sound settings will not be memorized after the unit goes into Standby mode. 1 Before you begin: Make sure the unit is connected to antenna or cable. 1 Press MENU / EXIT and use ▲▼ to select Sound, then press OK.
• When the scanning and memorizing are completed, the lowest memorized channel will be displayed. Autoprogram This function lets you add the off the air Analog TV or Analog Cable channels that were not added by the autoprogram due to reception conditions during the initial setting. Please wait while the system is scanning for channels. Auto programming may take more than 20 minutes to complete.
Analog/Cable TV operation Features 1 Press MENU / EXIT and use ▲▼ to select Features, then press OK. Picture Sound Setup Features Language USB 2 Caption settings Child lock PC settings EasyLink Location E-sticker Software upgrade Caption service Home -- Adjust the following items. Off Select if you do not want caption service. CC-1 and T-1 The primary caption and text services.
Note Picture Sound Setup Features Language USB •• Digital caption service that you can switch differs depending on the broadcast description. •• Caption style will not effect if the User setting is set to Off. •• Closed Captioning service may not be controlled by this unit’s menu options if you are •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• watching television through an external cable or satellite set-top box.
Setting US movie and TV ratings US movie ratings lock is the rating system created by MPAA. US TV ratings lock has controlled access to individual programs based on their age ratings and content rating. 3 4 Use ▲▼ to select US movie ratings lock or US TV ratings lock, then press OK. Use ▲▼ to select the desired rating, then press OK repeatedly to switch between view and block. • For US TV ratings, you can further set the sub ratings to block specific elements of programming.
Canadian English or Canadian French ratings You can select the rating for Canadian English or Canadian French broadcasting. 3 4 Use ▲▼ to select Canadian English rating or Canadian French rating, then press OK. Use ▲▼ to select the desired rating, then press OK repeatedly to switch between view and block. • indicates that the rating is locked. • indicates that the rating is not locked. Canadian English rating This function lets you adjust the PC screen position, clock and phase during PC Input.
Device list EasyLink This function allows you to operate the linked functions between our brand devices with a EasyLink feature and this unit connecting through an HDMI cable. You must connect this unit to our brand EasyLink devices and be sure its EasyLink setting is also set to On. 1 Use ▲▼ to select EasyLink, then press OK.
Setting your location to home Language You can set the location of your TV to Home or Retail. Choosing Home gives you full flexibility to change predefined settings for picture and sound. 1 Use ▲▼ to select Location, then press OK. Picture Sound Setup Features Language USB 2 Caption settings Child lock PC settings EasyLink Location E-sticker Software upgrade Retail The unit will be set up with predefined settings for retail displays.
Picture (JPEG) USB 1 Use ▲▼ to select the desired file, then press OK. Your TV is fitted with a USB connection that enables you to view photos or watch Motion JPEG files stored on a USB Memory Stick. 1 Picture Sound Setup Features Language USB Picture Picture Image1.jpg .. Image1.jpg Image2.jpg Image3.jpg Image4.jpg Image5.jpg Connect the USB Memory Stick to the USB terminal on the side of your TV. Press MENU / EXIT and use ▲▼ to select USB, then press OK.
6 Upgrade your TV software Philips continuously tries to improve its products and we strongly recommend that you upgrade the TV software when upgrades are available. New software can be downloaded from our website at www.philips.com/support using the model number of your TV to find information. Checking your current software version 1 Press MENU / EXIT and use ▲▼ to select Features, then press OK. 2 Use ▲▼ to select Software upgrade, then press OK.
7 Connecting devices No supplied cables are used with these connections: •• Please purchase the necessary cables at your local store. Before you connect AC power cord: Be sure other devices are connected properly before plugging in the AC power cord. Selecting your connection quality Connecting your devices HDMI Digital connection HDMI connection offers the highest picture quality.
Component Analog Video Connection Digital Audio Output Connection Component Analog Video connection offers better picture quality for video devices connected to the unit. If you connect to the unit’s Component Video (Y/Pb/Pr) Input jacks, connect Analog Audio cables to the Analog Audio (L/R) Input jacks. If you connect this unit to an external Digital Audio device, you can enjoy multi-channel audio like 5.1ch Digital broadcasting sound.
The following video signals can be displayed: PC connection Format HDMI connection VGA This unit can be connected to your PC that has a HDMI terminal. Use an HDMI cable for this Digital connection. IN HDMI cable 640 x 480 800 x 600 XGA 1,024 x 768 1,280 x 768 1,360 x 768 60Hz Note •• Please purchase the VGA cable or HDMI-DVI conversion cable that has a ferrite core. •• The following operations may reduce noise.
8 Useful tips FAQ Question My remote control does not work. What should I do? Answer •• Check the antenna or cable connection to the main unit. •• Check the batteries of the remote control. •• Check if there is an obstacle between the infrared sensor window and the remote control. •• Test the signal Output use IR Signal Check. ➠ p.35 If okay, then possible infrared sensor trouble. •• Aim the remote control directly at the infrared sensor window on the front of the unit.
Symptom Remedy Power is ON but no screen image. •• Check whether the connection of the antenna, cable receiver or satellite box is connected correctly. •• Check whether all the cables to the unit are connected to the correct Output jack of your device like Blu-ray disc / DVD recorder. •• Make sure that the selected Input mode is connected to the working Input jack. •• Check if your computer is NOT in sleep mode when the Input mode of this unit is in PC mode.
9 Information Glossary Maintenance Cabinet Cleaning Analog TV (NTSC) Acronym that stands for National Television Systems Committee and the name of Analog broadcasting standards. Off the air Analog TV signals are no longer being sent by major broadcasting stations in the USA. Aspect ratio The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the TV screen is almost square); widescreen models are 16:9 (the TV screen is almost twice as wide as its height).
10 Specifications Model # 32PFL4507 26PFL4507 22PFL4507 Picture Type WXGA (1366 x 768 pixels 60Hz) Aspect ratio 16:9 Viewing angles 170° (V) by 170° (H) 150° (V) by 160° (H) Built-in Digital tuner ATSC / NTSC Mono / Stereo Mono, Stereo, SRS TruSurround XT® 160° (V) by 170° (H) Sound Power Output (RMS watts) 8W x 2 Equalizer 2W x 2 5 band Ease of use Picture format SD (4:3 Source) HD (16:9 Source) HDMI AV (4:3 Source) HDMI AV (16:9 Source) PC Source : Normal / 16:9 / Movie ex
11 Warranty LIMITED WARRANTY ONE (1) YEAR WARRANTY COVERAGE: This warranty obligation is limited to the terms as set forth below. WHO IS COVERED: This product warranty is issued to the original purchaser or the person receiving the product as a gift against defects in materials and workmanship as based on the date of original purchase (“Warranty Period”) from an Authorized Dealer.
P&F USA, Inc. PO Box 2248, Alpharetta, GA 30023-2248 P&F Mexicana, S.A. de C.V. Av. La Palma No. 6, Col. San Fernando La Herradura, Huixquilucan Edo. de México C.P. 52787 Philips and Philips Shield are used under license of Koninklijke Philips Electronics N.V.
