Register your product and get support at www.philips.
Model Serial www.philips.
1 Notice 2 2 Important 4 27 27 28 29 29 29 Automatically install channels Manually install channels Rename channels Rearrange channels Test digital reception 7 Connect devices 3 Your TV Side controls and indicators Remote control 4 Use your TV Switch your TV on / off or to standby Switch channels Watch connected devices Adjust TV volume Use teletext 5 Use more of your TV 7 7 7 9 9 9 10 10 10 11 Access TV menus 11 Rename devices from the home menu 11 Remove devices from the home menu 11 Change pict
1 Notice 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
1 2 Remove fuse cover and fuse. The replacement fuse must comply with BS 1362 and have the ASTA approval mark. If the fuse is lost, contact your dealer in order to verify the correct type. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. All other registered and unregistered trademarks are the property of their respective owners. 3 Refit the fuse cover.
2 Important Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety Risk of electric shock or fire! • Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
When you disconnect the power cord, always pull the plug, never the cable. • Disconnect the TV from the power outlet and antenna before lightning storms. During lightning storms, never touch any part of the TV, power cord or antenna cable. Risk of hearing damage! • Avoid using earphones or headphones at high volumes or for prolonged periods of time.
Environmental efforts • High energy efficiency • Low standby power • Designed to facilitate recycling Philips continuously focuses on lowering the environmental impact of its innovative consumer products. We aim our efforts towards environmental improvements during manufacturing, reduction of harmful substances, energy-efficient use, end-of-life instructions and product recycling. Thanks to our environmental effort, this TV has been awarded the European Ecolabel –the flower– www.ecolabel.
Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your TV at www.philips.com/welcome. 1 2 22 21 20 This section gives you an overview of commonly used TV controls and functions. E n g l i sh Remote control 3 Your TV 19 3 4 5 6 7 8 Side controls and indicators 18 9 17 10 11 16 12 1 2 3 13 4 5 a +/-: Increases or decreases volume. b (Home): Toggles the home menu on or off.
a (Standby-On) • Switches the TV to standby if it is on. • Switches on the TV if it is in standby. b MENU Toggles the main menu on or off. c MHEG/TELETEXT Toggles teletext on or off. d SOURCE Selects connected devices. o SOUND (Smart Sound) Launches the sound menu. p +/- (Volume +/-) Increases or decreases volume. q BACK P/P (Previous channel) • Returns to a previous screen. • Returns to the previously viewed channel. r GUIDE Switches between channel grid and programme list.
Switch channels • This section helps you perform basic TV operations. Switch your TV on / off or to standby • • • Press P +/- on the remote control or P/CH +/- on the side of the TV. Enter a channel number using the Numeric buttons. Press OK to use the channel grid. Press BACK P/P on the remote control to return to the previous channel. Note • When you use a favourite list, you can only select those channels in the list (see ‘Select a favourite list’ on page 16).
Watch connected devices Use teletext Note • Switch on the device before selecting it as a source on the TV. Use the source button 1 Press SOURCE. » The source list appears. 2 3 Press 1 Press MHEG/TELETEXT. » The main index page appears.
Rename devices from the home menu Access TV menus 1 2 3 After adding a new device to the home menu, you can rename it to your preference. Menus help you to install channels, change picture and sound settings and access other features. 1 Press MENU. » The menu screen appears. Add new device Setup Watch TV Press Press MENU. to select a device to rename. Press OPTIONS. » The options menu appears. 4 Press to select [Rename device], then press OK. » A text input box appears.
Change picture and sound settings • Change picture and sound settings to suit your preferences. You can apply pre-defined settings or change settings manually. • • 3 Note [Energy saving]: Applies low-energy settings. [Natural]: Applies the best picture quality. [Custom]: Lists customised picture settings. Press OK to confirm your choice. » The selected smart picture setting is applied.
• • • • • [Dynamic backlight]: Adjusts brightness of the TV backlight to match lighting conditions. • [MPEG artifact reduction]: Smoothes out transitions on digital pictures. You can switch this feature on or off. • [Colour enhancement]: Makes colours more vivid and improves the details in bright colours. You can switch this feature on or off. [PC mode]: Adjusts the picture when a PC is connected to the TV via HDMI or DVI. [Picture format]: Changes the picture format.
Use smart sound • Use smart sound to apply pre-defined sound settings. • 1 2 3 Press SOUND. » The [Smart sound] menu appears. Press to select the following settings. • [Custom]: Applies the settings that were customised in the sound menu. • [Standard]: Adjusts sound settings to suit most environments and types of audio. • [News]: Applies settings for spoken audio, such as news. • [Movie]: Applies settings for movies. Press OK to confirm your choice. » The selected smart sound setting is applied.
Use advanced teletext features You can activate the universal access menu during the first installation. Once enabled, you can quickly access the visually impaired and hearing impaired menus when watching TV or external devices. Access the teletext options menu Tip Access the teletext features through the teletext options menu. 1 Press MHEG/TELETEXT. » The teletext screen appears. 2 Press OPTIONS. » The teletext options menu appears. 3 Press to select one of the following options.
Select T.O.P. teletext broadcasts Table Of Pages (T.O.P.) teletext broadcasts allow you to jump from one subject to another without using page numbers. T.O.P. teletext is not broadcast on all TV channels. 1 Press MHEG/TELETEXT. » The teletext screen appears. 2 Press INFO. » The T.O.P. overview appears. Create and use list of favourite channels You can create a list of your preferred TV channels so that you can find those channels easily.
Tip • View all channels before adding a channel to a favourite list. 1 When watching TV, press OK. » The channel grid appears. 2 Press to select a channel to add to a favourite list. 3 Press OPTIONS. » The channel options menu appears. 4 Select [Mark as favourite], then press OK. » The channel is added to the favourite list. Use the Electronic Programme Guide E n g l i sh Add a channel to a favourite list EPG is an on-screen guide available for digital channels.
Use the EPG options menu Use the EPG options menu to set or clear reminders, change day and access other useful EPG options. 1 2 3 4 5 Press GUIDE. Press OPTIONS. » The EPG menu appears. Press to select one of the following options. • [Set remind] / [Clear remind]: Sets or clears programme reminders. • [Change day]: Sets the EPG day. • [Show info]: Displays programme information. • [Search by genre]: Searches TV programmes by genre. • [Scheduled reminders]: Lists programme reminders.
Use timers 1 2 You can set timers to switch the TV to standby at a specified time. Press MENU. Press to select [Setup] > [Installation] > [Clock] > [Auto clock mode]. 3 Press to select [Automatic] or [Manual]. 4 Press OK to confirm. Change the time zone 1 2 3 4 Press MENU. Press to select [Setup] > [Installation] > [Clock] > [Time zone]. Press Tip • Set the TV clock before you use timers.
Automatically switch the TV on (on timer) You can switch on the TV from standby to a specific channel at a specified time. 1 2 3 4 Press MENU. Lock or unlock the TV Lock the TV to prevent access to all channels and connected devices. 1 2 Press to select [Setup] > [Features] > [On timer]. Press to enter the [On timer] menu. • [Activate]: Selects how often the TV is switched on. • [Time]: Sets the time to switch on the TV. • [Programme no.]: Selects the channel or the connected device.
• You have to enter your code every time you turn on your TV. • Switch the TV off and on again for the change to take effect. Lock or unlock one or more channels 1 When watching TV, press OK to display the channel grid. 2 Press unlock. 3 4 Press 5 to select a channel to lock or OPTIONS. Press to select [Lock channel] or [Unlock channel]. For each selection, press OK to lock or unlock the channel. » The first time you lock or unlock a channel, you are prompted to enter your PIN code.
Tip • Select [Subtitle mode] > [Off] to disable View photos and play music from a USB storage device subtitles. Caution • Philips is not responsible if the USB storage device is not supported, nor is it responsible for damage or loss of data from the device. Enable subtitles on digital TV channels 1 When watching digital channels, press SUBTITLE. » The [Subtitle mode] menu appears. 2 Select [On] to display subtitles always or [On during mute] to display subtitles only when audio is muted.
Listen to music 1 When a full screen image of a photo is displayed, press OK. » A slide show begins from the selected photo. 1 In the USB thumbnail browser view, select [Music] and press to enter. • Press GUIDE to switch between thumbnail and file browsing views. 2 Press the following buttons to control the slide show: • OK to pause the slide show. • to go back or move forward to the next image. • BACK to stop the slide show. 2 Press album. 3 Press OK to play the selected music.
Disconnect a USB storage device Caution • Follow this procedure to avoid damage to your USB storage device. 1 2 Press BACK to exit the USB browser. Wait for five seconds then disconnect the USB storage device. Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available. Check www.philips.com/support for availability.
1 2 3 4 If using (DVB-T) digital broadcast, your TV automatically receives software updates. If you receive a message on your screen asking you to update your software: • Select [Update now] to update the software immediately. • Select [Remind me later] to exit the update screen at that time and be reminded later. • Select [Cancel] to skip the update. If you select [Cancel], you can manually access the OAD update by selecting [Setup] > [Software update] > [Local updates] > [OAD].
Access decoder channel Start a TV demo You can map channels provided through a decoder or descrambler to your TV channel selection. In this way, you can select these channels by using the RC of your TV. The decoder or a descrambler must be connected to EXT1 (SCART). You can use demonstrations to better understand the features of your TV. Some demos are not available on certain models. Available demos are displayed in the menu list. 1 2 Press DEMO on the remote control.
The first time you set up your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available). This chapter provides instructions on how to re-install and fine tune channels. Automatically install channels This section describes how to search and store channels automatically. Step 1 Select your menu language 1 2 3 4 5 6 Press MENU. Press to select [Setup] > [Installation] > [Language] > [Menu language]. Press OK or Press to enter [Menu language].
Manually install channels 7 This section describes how to search and store analogue TV channels manually. Press to select [Store as new channel] to store the new channel under a new channel number. 8 Press OK to enter [Store as new channel], then press OK. Step 1 Select your system 9 Press to return to the [Channel installation] menu. Note • Skip this step if your system settings are correct. 1 2 Press MENU.
Test digital reception You can rename channels. The name appears when you select the channel. You can check the quality and signal strength of digital channels. This allows you to reposition and test your antenna or satellite dish. 1 When watching TV, press OK to display the channel grid. 2 3 Select the channel to rename. 4 5 6 7 Press OPTIONS. » The channel options menu appears. Press to select [Rename channel], then press OK. » A text input box appears.
7 Connect devices This section describes how to connect devices with different connectors. Examples are provided in the Quick Start. a TV ANTENNA Signal input from an antenna, cable or satellite. TV ANTENNA Note • You can use different types of connectors to connect a device to your TV. Back connector b EXT 1 and EXT 2 (CVBS and RGB) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles.
e PC IN (VGA and AUDIO IN) Audio and video input from a computer. g EXT 3 (Y Pb Pr and AUDIO L/R) Analogue audio and video input from analogue or digital devices such as DVD players or game consoles. E n g l i sh d SERV. U For use by service personnel only. VGA VGA AUDIO IN LEFT/RIGHT VGA/DVI f HDMI 1 Digital audio and video input from highdefinition digital devices such as Blu-ray players. Connections via DVI or VGA require an additional audio cable (see ‘Connect a computer’ on page 33).
Side connector b VIDEO Composite video input from analogue devices such as VCRs. c USB Data input from USB storage devices. a AUDIO L/R Audio input from analogue devices connected to VIDEO. 32 EN d HDMI Digital audio and video input from highdefinition digital devices such as Blu-ray players.
(Headphone) Stereo audio output to headphones or earphones. • DVI-HDMI cable E n g l i sh e AUDIO IN LEFT/RIGHT VGA/DVI f COMMON INTERFACE Slot for a Conditional Access Module (CAM). DVI • Connect a computer HDMI cable and HDMI-DVI adaptor AUDIO IN LEFT/RIGHT VGA/DVI Before you connect a computer to the TV • Set the screen refresh rate on your computer to 60Hz. • Select a supported screen resolution on your computer.
Use a Conditional Access Module Access CAM services 1 After inserting and activating the CAM, press MENU. A Conditional Access Module (CAM) is provided by digital TV service operators to decode digital TV channels. 2 Press to select [Setup] > [Features] > [Common interface]. » Applications provided by the digital TV service operator appear on the screen. Note • Refer to the documentation from your service operator on how to insert a smart card into the Conditional Access Module.
Set TV speakers to EasyLink mode One-touch play When you connect your TV to devices that support one-touch play, you can control your TV and the devices with one remote control. One-touch standby When you connect your TV to devices that support standby, you can use your TV remote control to put your TV and all connected HDMI devices in standby mode. System audio control When you connect your TV to HDMI CEC compliant devices, your TV can switch automatically to play audio from the connected device.
8 Product information Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.
Product specification To mount the TV, purchase a Philips TV mount or a VESA-compatible TV mount. To prevent damage to cables and connectors, be sure to leave a clearance of at least 2.2 inches or 5.5cm from the back of the TV. Design and specifications are subject to change without notice. Warning • Follow all instructions provided with the TV mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper TV mounting that results in accident, injury or damage.
9 Troubleshooting This section describes commonly encountered issues and accompanying solutions. General TV issues The TV does not switch on: • Disconnect the power cable from the power outlet. Wait for one minute then reconnect it. • Check that the power cable is securely connected. The remote control is not working properly: • Check that the remote control batteries are correctly inserted according to the +/- orientation. • Replace the remote control batteries if they are flat or weak.
Sound issues The TV is on, but there is no picture: • Check that the antenna is properly connected to the TV. • Check that the correct device is selected as the TV source. There is sound but no picture: • Check that the picture settings are correctly set. There is poor TV reception from an antenna connection: • Check that the antenna is properly connected to the TV. • Loudspeakers, unearthed audio devices, neon lights, high buildings and other large objects can influence reception quality.
Computer connection issues The computer display on the TV is not stable: • Check that your PC uses the supported resolution and refresh rate. • Set the TV picture format to unscaled. Contact us If you cannot resolve your problem, refer to the FAQs for this product at www.philips.com/support. If the problem remains unresolved, contact Philips Consumer Care in your country as listed in the Addendum. Warning • Do not attempt to repair the product yourself.
A analogue fine-tune antenna 28 30 B back connectors batteries bracket for wall mount 30 36, 5 37 C CAM care channel decoder channel grid channels favourites list fine-tune grid install automatic manual list lock rename reorder / rearrange switch test reception (digital channels) troubleshooting tune update child lock lock channels lock connected devices 34 5 26 9 16 28 9 27 28 16 20 29 29 9 29 38 28 17 20 20 PIN code ratings lock clock display set common interface computer connect display resolution Co
digital services CAM teletext disconnect USB display resolution dispose 34 16, 10, 15 24 36 5 E EasyLink disable enable one-touch play one-touch standby system audio control eco-green end of life energy efficiency environmental care e-sticker 35 35 35 35 35 6 5 6 5 24 F factory settings favourites list add to list create list view list fine-tune channels 25 17 16 16 27 G green language menu subtitle troubleshoot list favourites list location country home or shop lock Kensington lock lock channels lock
32, 39 36 13 38 12 20 24 36 36, 6 24 36 R radio rearrange channels reception recycle register product remote control batteries overview technical specifications rename channels reorder channels resolution restore default 23 28 28, 38 5 7 36, 5 7 36 28 28 36 25 S safety screen care settings picture sound settings assistant shop mode side connectors slideshow view with music smart card smart picture smart settings smart sound software 4 5 12 14, 12 12 24 31 22 23 33 12 12, 14 14 over the air download upda
view photos 22 V video format technical specifications volume adjust automatic levelling delta mute 36 10 14 14 10, 34 W wall mount 44 EN 4, 37
45 EN
EN 46
© 2010 Koninklijke Philips Electronics N.V. All rights reserved.
