Register your product and get support at www.philips.
Contents 1 2 3 4 5 Important 3 Safety Care Legal Sustainability Help and support 3 4 5 7 8 Use your TV 9 TV controls Watch TV View programme guide Watch 3D Play multimedia files 9 10 13 13 15 Use more of your TV 17 View Text Set locks and timers 17 17 Change your TV settings 20 Picture and sound Channels Language settings Other settings Update software Reset all 20 21 24 25 25 26 Connect your TV 27 About cables 27 Connect antenna 28 Connect devices 28 Connect more devices 33 Watch con
Safety Precautions Read and understand all instructions before you use your TV. If damage is caused by failure to follow the instructions, the warranty does not apply. Risk of electric shock or fire! Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilled on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips TV Consumer Care to have the TV checked before use.
Never place the TV on tall furniture, such as a bookcase, without anchoring both the furniture and TV to the wall or a suitable support. Educate children about the dangers of climbing on furniture to reach the TV. Risk of swallowing batteries! The product or remote control may contain a coin-type battery, which can be swallowed. Keep the battery out of reach of children at all times! Risk of overheating! Never install the TV in a confined space.
Lock the TV For sets with 3D glasses supplied. Your TV is equipped with a Kensington security slot at the base of the TV. To secure the TV, purchase a Kensington anti-theft lock (sold separately). Follow these instructions to take care of your glasses: Use a clean soft cloth (microfibre or cotton flannel) to clean the lenses to avoid scratching them. Never spray cleaner directly on the 3D glasses. You can use pre-moistened cleaning cloths from most well-known lens manufacturers of sunglasses.
TP Vision cannot be held responsible for any errors in the content of this document nor for any problems as a result of the content of this document. Errors reported to TP Vision will be amended and published on the Philips support website as soon as possible. Terms of warranty The terms of warranty can be downloaded from the Philips support website.
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. Manufactured under licence from Dolby Laboratories. Dolby and the double D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed of with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environment and human health. Use the Philips connectivity guide An easy-to-use connectivity guide gives you guidance on how to connect your TV to other devices. Visit http://www.connectivityguide.philips.com.
TV controls Sensors and indicators 1. (Standby): Switch the TV on or to standby. 2. Play buttons: Control playback of media files. 3. SOURCE: Access a connected device. 4. FORMAT: Change picture format. 5. TV: Switch source to watch TV. 6. (Home): Access the Home menu. 7. OK: Confirm an entry or selection. 8. (Navigation buttons): Navigate through menus and select items. 1. Standby indicator LED and remote control sensor The standby LED indicates when your TV is in standby.
13. (Back): Return to the previous menu page or exit from a TV function. 14. CH - / CH +: Switch channels. 15. +/-(Volume): Adjust volume. 16. (Mute): Mute or restore audio. 17. Colour buttons: Select tasks or options. The buttons function according to the services offered by the service provider. 18. SUBTITLE: Switch subtitles on or off. 19. 0-9 (Numeric buttons): Select TV channels or enter text. 20. TEXT: Enable or disable text.
Press CH +/- on the remote control. Press the Numeric buttons to enter a channel number. Manage favourite channels You can view all channels or only a list of your favourite channels. Create a list of your favourite channels 1. Press LIST. The channel list is displayed. 2. Select the channel to mark as favourite, then press OPTIONS. 3. Select [Add/remove favourites], then press OK. The selected channel is marked with an asterisk.
3. Select [Rename], then press OK. The onscreen keyboard is displayed. 4. Press the Navigation buttons to select each character, then press OK. 5. Once complete, select [Done], then press OK to confirm. Lock a channel You can prevent unauthorised access to channels by locking them. 1. While you watch TV, press LIST. The channel list is displayed. 2. Select the channel to lock, then press OPTIONS. 3. Select [Lock channel], then press OK. 4. If prompted, enter the PIN code.
[Super zoom]: Remove the black bars on the sides of 4:3 broadcasts. Not recommended for HD or PC. [Movie expand 16:9]: Scale 4:3 format to 16:9. Not recommended for HD or PC. [Wide screen]: Shows widescreen format content unstretched. Not recommended for HD or PC. [Unscaled]: Provide maximum detail for PC. Only available when PC mode is selected in the Picture menu. [4:3]: Display the classic 4:3 format. 1. In the programme guide, press OPTIONS. 2.
Sit at a distance that is at least three times the width (w) of the TV screen. Do not sit more than 6 m away. Start 3D Automatically enable 3D The TV detects when 3D is available and prompts you to put on your 3D glasses to start watching. To set the TV response when a 3D signal is detected: 1. Press . 2. Select [Setup] > [TV settings] > [3D] > [Switch to 3D]. 3. Select a setting, then press OK. [Automatic]: TV switches to 3D automatically. [Notification only]: TV displays notification first.
What you can do You can play videos, photos, music and text files on your TV from a USB device connected to the TV. Play files from USB device If you have photos, videos or music files on a USB storage device, you can play the files on TV. Caution: TP Vision is not responsible if the USB hard drive is not supported, nor is it responsible for damage to or loss of data in the device. Do not overload the USB port.
View pictures Press the Navigation buttons to select a picture, then press OK to start the slideshow. Press Navigation buttons to search for a picture. Press to exit content browser. Slideshow options While you play a slideshow, press OPTIONS, then press OK to select an option: [Slideshow frequency]: Select the display time for each picture in the slideshow. [Slideshow transitions]: Select the transition from one picture to the next.
View Text Select a page While you watch channels that broadcast text, you can view the text. 1. Select a channel that broadcasts text, then press TEXT. 2. Select a page in one of the following ways: Enter the page number with the Numeric buttons. Press CH + / CH - to view the next or previous page. Press the Colour buttons to select a colour coded item. Text options 1. While you view text, press OPTIONS. 2. Select an option: [Freeze page] / [Unfreeze page]: Freeze or unfreeze the current page.
1. While you watch TV, press . 2. Select [Setup] > [TV settings] > [General settings]. 3. Select [Clock] > [Auto clock mode]. 4. Select [Automatic], [Manual] or [Country dependent], then press OK. Change the time zone* In countries with clock transmission data, you can change the time zone if [Auto clock mode] > [Automatic] or [Country dependent] is selected. 1. In the [Clock] menu, select [Time zone]. 2. Select your time zone, then press OK.
English For information on child lock codes, see Use more of your TV > Set locks and timers > Child lock (Page 18).
4 Change your TV settings Picture and sound Picture settings You can change the settings in the Picture menu. 1. Press . 2. Select [Setup] > [TV settings] > [Picture], then press OK. 3. Select a setting to change, then press OK. EN [Picture style]: Select a predefined picture setting. [Restore style]: Restore the lastselected predefined picture setting. [3D backlight contrast] / [Backlight contrast]: Adjust the brightness of the display backlight.
[Advanced]: Access advanced settings to enhance your audio experience. - [Auto volume levelling]:Enable the reduction of sudden volume changes, for example, when switching channels. - [TV speakers]: Select the preferred speakers to stream audio from the TV. See Connect your TV > Set up EasyLink devices > Select speaker output (Page 35). - [Clear Sound]*: Enhance sound quality. - [Audio Out format]: Select the type of audio output through the digital audio output connector.
Install analogue channels You can search and store analogue TV channels one by one. Step 1: Select your system Note: Skip this step if your system settings are correct. 1. While you watch TV, press . 2. Select [Setup] > [Channel settings] > [Channel installation]. 3. Select [Analogue: Manual installation] > [System], then press OK. 4. Select the system for your country or region, then press OK. Step 2: Search and store new TV channels 1. While you watch TV, press . 2.
Update channels manually 1. Press . 2. Select [Setup] > [Search for channels] > [Update channels], then press OK. 3. Follow the onscreen instructions to update the channels. Copy channels ATTENTION: This feature is intended for dealers and service personnel. You can copy channel lists from one Philips TV to another through a USB storage device. You do not need to search for channels or install them again on the second TV. The channel list file is small enough to fit on any USB storage device.
4. Make sure that the country setting is the same as for the first TV. 5. Press . 6. Press [Cancel] to exit. 7. If the country setting is different, reinstall the second TV to match the country setting of the first TV. See Change your TV settings > Reset all (Page 26). 8. Connect the USB storage device to the second TV. 9. Press . 10. Select [Setup] > [Channel settings]. 11. Select [Channel installation] > [Copy channel list] > [Copy to TV], then press OK. The channel list is copied to the second TV. 12.
TV demo You can watch a demo to find out more about the features on this TV. 1. While you watch TV, press . 2. Select [Setup] > [Watch demo], then press OK. 3. Select a demo, then press OK. Home mode Some TV settings may not be available in Shop mode. To make sure that the correct TV settings are applied, set the TV to Home mode. 1. While you watch TV, press . 2. Select [Setup], then press OK. 3. Select [TV settings] > [General settings] > [Location]. 4. Select [Home] or [Shop], then press OK. 5.
Upgrade the TV software Caution: Do not switch off the TV or remove the USB flash drive during the software upgrade. If a power failure occurs during the upgrade, do not remove the USB flash drive from the TV. The TV continues the upgrade as soon as power is restored. If an error occurs during the upgrade, retry the upgrade from the beginning. If the error reoccurs, contact Philips TV Consumer Care. 1. Remove all USB devices such as a Wi-Fi adapter from the TV, then switch on the TV. 2.
Connect HDMI cables shorter than 5 meters/16.4 feet. About cables Cable quality Before you connect devices to the TV, check the available connectors on the device. Connect the device to the TV with the highest quality connection available. Good quality connectors transfer picture and sound better. The connections shown in this user manual are recommendations only. Other solutions are possible. For more examples, visit http://www.connectivityguide.philips.com.
Connect antenna Connect the antenna to the TV. Connect devices Blu-ray or DVD disc player Connect the disc player to the TV with an HDMI cable.
TV receiver English Connect the digital TV receiver with an antenna cable to the TV. Connect the digital TV receiver to the TV with an HDMI cable. Connect the digital TV receiver to the TV with a SCART cable.
Video recorder Connect the recorder to the TV with an antenna cable. Connect the recorder to the TV with an HDMI cable. Connect the recorder to the TV with a SCART cable.
Game console English Connect the game console to the TV with an HDMI cable. Home theatre Connect an HDMI-ARC compliant home theatre to the TV with an HDMI cable. Connect the home theatre with an HDMI cable and an optical audio cable to the TV.
Connect the home theatre to the TV with a SCART cable. Digital camera Connect the digital camera to the TV with a USB cable. Digital camcorder Connect the digital camcorder to the TV with an HDMI cable.
English Connect more devices USB storage device Connect the USB flash drive with a USB cable to the TV. Connect the USB hard drive to the TV with a USB cable. Computer Connect the computer to the TV with an HDMI cable.
(For certain sets only.) Connect the computer with a DVI-HDMI cable and an audio cable to the TV. Watch connected devices Select a device Before you can watch a device, connect the device to the TV. See Connect your TV > Connect devices (Page 28). Select a device with SOURCE 1. Press SOURCE. 2. Select a device, then press OK. Select a device from Home menu 1. Press . 2. Select [Source], then press OK. 3. Select a device, then press OK.
If you connect multiple HDMI-CEC devices that support this setting, you can control all such devices through the TV remote control. Note: This is an advanced setting. Devices that do not support this setting cannot respond to the TV remote control. 1. Press . 2. Select [Setup] > [TV settings] > [General settings] > [EasyLink] > [EasyLink remote control]. 3. Select [On] or [Off], then press OK. Tips: To switch back to TV control, press , then select [TV].
Connect a CAM (Conditional Access Module) What you can do You can watch scrambled digital TV channels with a Conditional Access Module (CAM). Once you have inserted the CAM and paid the subscription fees, you can watch the programmes. This TV supports CI (Common Interface) as well as CI+. CI+ supports premium HD digital programmes with a high level of copy protection. Note: The applications, functions, content and onscreen messages depend on the CAM service provider.
General issues The TV does not switch on: Disconnect the power cable from the power outlet. Wait for one minute then reconnect it. Make sure that the power cable is securely connected. When you are turning the TV on, off or to standby, you hear a creaking sound from the TV chassis: No action is required. The creaking sound is due to the normal expansion and contraction of the TV as it cools and warms up. This does not affect performance.
Make sure that all cables are properly connected and that the correct network is selected. Previously installed channels do not appear in the channel list: Make sure that the correct channel list is selected. You want to rearrange or reorder the channel list: After channels have been installed, they appear in the channel list. For information about managing channel lists, including rearranging channels, see Watch TV > Manage channel lists (Page 11).
Make sure that the TV speaker setting is selected. Press OPTIONS, select [Picture and sound] > [Speakers], then select [TV]. Make sure that the TV audio output is connected to the audio input on the HDMI-CEC enabled or EasyLink compliant home theatre device. Sound should be heard from the home theatre speakers. Some devices may require you to manually enable HDMI audio output.
7 Specifications Power and reception Product specifications are subject to change without notice. Power Mains power: AC 220-240 V (50-60 Hz) Standby power consumption: < 0.3 W Ambient temperature: 5 to 40 degree Celsius For power consumption, see the product specifications at www.philips.com/support. The power rating stated on the product typeplate is the power consumption for this product during normal household use (IEC 62087 Ed.2).
Video formats (Resolution - refresh rate) 480i - 60 Hz 480p - 60 Hz 576i - 50 Hz 576p - 50 Hz 720p - 50Hz, 60 Hz 1080i - 50Hz, 60 Hz 1080p - 24Hz, 25Hz, 30Hz, 50Hz, 60 Hz Multimedia Note: Multimedia file names must not exceed 128 characters. Supported multimedia connections USB 2.0 (FAT / FAT 32 / NTFS): only connect USB devices that consume 500 mA of power or less. Supported image files JPEG: *.jpg, *.jpeg PNG: *.png Supported audio files MPEG1: *.
Connectivity 32-39PFL3xx8H/T and 39PFL4398H/T: Rear connectors HDMI 2 SERV.
8 Index channels, switch - 11 3 child lock - 18 3D - 13 3D glasses, care - 5 3D, 2D to 3D - 14 3D, change format - 14 3D, health warning - 4 3D, start - 14 3D, switch off - 14 A amplifier, select output - 35 analogue channels, fine-tune - 22 analogue channels, install - 22 analogue channels, subtitles - 24 audio language - 24 Auto switch off, devices - 35 CI - 36 clock - 17 codecs, supported - 41 Common Interface - 36 Conditional Access Module - 36 connect, computer - 33 connect, digital camcorder - 3
EasyLink, controls - 35 EasyLink, enable - 34 EasyLink, features - 34 multimedia, supported formats - 41 O EasyLink, onscreen control - 10 online forum - 8 EasyLink, remote control - 35 P EasyLink, TV speakers - 35 Energy label - 8 energy-efficient settings - 7 EPG, broadcaster - 13 external hard disk - 33 parental rating - 18 PC, display resolutions - 40 picture format - 12 picture settings, reset - 21 placement, stand or wall - 5 F placement, tips - 5 favourite channels, list - 11 play, USB fi
source, select - 12 English standby - 10 standby LED - 9 subtitles, analog - 24 subtitles, digital - 24 subtitles, language - 24 sustainability - 7 switch TV on, off - 10 T text 2.
All registered and unregistered trademarks are the property of their respective owners. Specifications are subject to change without notice. Philips and the Philips‘ shield emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. 2013 © TP Vision Netherlands B.V. All rights reserved. www.philips.
