Brilliance 329P9 www.philips.
Table of Contents 1. Important �������������������������������������� 1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the monitor �������������� 5 2.1 Installation ������������������������������������ 5 2.2 Operating the display ���������������� 8 2.
1. Important 1. Important • Do not block the ventilation holes on the cabinet. This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user’s manual before you use your monitor. It contains important information and notes regarding the operation of your monitor. • When positioning the monitor, make sure the power plug and outlet are easily accessible.
1. Important eyes from eye strain while using the screen for a constant period of time by : • rain, water, or excessive moisture environment. Looking at something varying distances after a long period focusing on the screen. • If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center. Conscious Blinking often while you work.
1. Important Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor 2 Install the base 2. Setting up the monitor 1. 2.1 Installation 1 Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. Package contents Brilliance 329P9 278E9 Quick Start Register your product and get support at www.philips.com/welcome 2. Hold the stand with both hands. (1) Gently attach the stand to the VESA mount area until the latch locks the stand.
2. Setting up the monitor Connect to PC 3 Connecting to your PC 1. Connect the power cord to the back of the display firmly. 2. Turn off your computer and unplug its power cable. 12 11 1 Fast Charger 10 9 8 7 6 5 4 3 3. Connect the display signal cable to the video connector on the back of your computer. 2 4. Plug the power cord of your computer and your display into a nearby outlet. USB type A-C 5. Turn on your computer and display.
2. Setting up the monitor 6. We recommend to periodically visit the above web link to check for the availability of the most updated driver. Note Please contact Philips service hotline for Mac address clone tool as necessary. < 5 USB hub To comply with International energy standards, the USB hub/ports of this display are disabled during Sleep and Power Off modes.
2. Setting up the monitor 2 Webcam 2.2 Operating the monitor 1 Description of the control buttons 1 7 2 3 6 1 5 2 3 2 4 1 3 4 2 1 1 Switch display’s power ON or OFF. 2 Access the OSD menu. Confirm the OSD adjustment. 3 Adjust the OSD menu. 4 User preference key. Customize your own preference function from OSD to become the “user 2”. 5 User preference key. Customize your own preference function from OSD to become the “user 1”. 6 Return to previous OSD level.
2. Setting up the monitor 3 Customize your own “USER” key This hot key allows you to setup your favorite function key. 1. 4 Description of the On Screen Display What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD displays. It allows an end user to adjust screen performance or select functions of the displays directly through an on-screen instruction window.
2. Setting up the monitor The OSD Menu 5 Resolution notification Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. This display is designed for optimal performance at its native resolution, 3840 x 2160 @ 60 Hz. When the display is powered on at a different resolution, an alert is displayed on screen: Use 3840 x 2160 @ 60 Hz for best results.
2.
2. Setting up the monitor Please follow the steps for the setting: 2.3 Built-in Windows Hello™ pop-up webcam 1 1. Press the built-in webcam on the top of this monitor, and turn it to the front. What is it? Phillips' innovative and secure webcam pops up when you need it and securely tucks back into the monitor when you are not using it.
2. Setting up the monitor 3. Setting in Windows 10 for Windows Hello a. In the settings app click on accounts. e. Click on "Get started." The setting is complete. Note 1. Please always go to Windows official website to access the latest information, the information in EDFU is subject to change without further notice. b. Click on sign-in options in the sidebar. c. You need to set up a PIN code before you're allowed to use Windows Hello. Once you've added this, the option for Hello will unlock. 2.
2. Setting up the monitor 2.4 MultiView Press ▲ or ▼ button to select main menu [PBP], then press button. • Press ▲ or ▼ button to select [PBP Mode], then press button. • Press ▲ or ▼ button to select [PBP]. • Now you can move backward to set the [PBP Input] or [Swap]. 2. Press button to confirm your selection.
2. Setting up the monitor Note The black strip shows on the top and the bottom of the screen for the correct aspect ratio when in the PbP mode. If you expect to see full screen side by side, adjust your devices resolutions as pop up attention resolution, you will able to see 2 devices source screen project to this display side by side without black strips. Note the analog signal is not support this full screen in PbP mode.
2. Setting up the monitor 2.5 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 100mm 100mm 2. Place the monitor face down on a smooth surface.
3. Image Optimization How to enable SmartImage? 3. Image Optimization 3.1 SmartImage What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized display performance. 1. Press to launch the SmartImage on screen display. 2.
3. Image Optimization • EasyRead: Helps improve reading of text based application like PDF ebooks. By using a special algorithm which increases the contrast and boundary sharpness of text content, the display is optimized for a stress-free reading by adjusting the brightness, contrast and color temperature of the monitor. • Office: Enhances text and dampens brightness to increase readability and reduce eye strain.
3. Image Optimization 3.2 SmartContrast What is it? Unique technology that dynamically analyzes displayed content and automatically optimizes a Display's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds. Why do I need it? You want the very best visual clarity and viewing comfort for every type of content.
4. PowerSensor™ detection signal for distances up to 120 cm or 47 inches. (Setting 4) 4. PowerSensor™ • How does it work? • PowerSensor works on principle of transmission and reception of harmless “infrared” signals in order to detect user-presence. • When the user is in front of the monitor, the monitor operates normally, at the predetermined settings that the user has set- i.e.
4. PowerSensor™ Note A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled. If you find that the PowerSensor is excessively sensitive to nearby motion for some reason, please adjust to a lower signal strength. Keep sensor lens clean, if the sensor lens is dirty, wipe it with alcohol to avoid reducing of distance detection .
5.LightSensor 5. LightSensor What is it? Light Sensor is a unique and intelligent way of optimizing picture quality by measuring and analyzing the incoming signal to automatically adjust picture quality settings. Light Sensor uses a sensor to adjust the picture brightness depending on the room light conditions. How to enable LightSensor? < 1. Press button on the front bezel to enter OSD menu screen. 2.
6. Technical Specifications 6. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio (typ.) Optimum Resolution Viewing Angle Flicker free Picture Enhancement Display Colors Vertical Refresh Rate Horizontal Frequency sRGB SmartUniformity Delta E LowBlue Mode EasyRead Connectivity Signal Input USB Power Delivery(USB C) RJ-45 Input Signal Audio In/Out Convenience IPS Technology LED 31.5" W (80 cm) 16:9 0.812(H) mm x 0.
6. Technical Specifications OSD Languages Other Convenience Plug & Play Compatibility Stand Tilt Pivot Swivel Height adjustment English, German, Spanish, Greek, French, Italian, Hungarian, Dutch, Portuguese, Brasil Portuguese, Polish, Russian, Swedish, Finnish, Turkish, Czech, Ukranian, Simplified Chinese, Traditional Chinese, Japanese, Korean VESA mount(100×100mm), Kensington Lock DDC/CI, Mac OS X, sRGB, Windows 10/8.
6. Technical Specifications Weight Product with stand Product without stand Product with packaging Operating Condition Temperature range (operation) Relative humidity (operation) Atmospheric pressure (operation) Temperature range (Non-operation) Relative humidity (Non-operation) Atmospheric pressure (Non-operation) Environmental and energy ROHS Packaging Specific Substances Cabinet Color Finish 10.63 kg 7.33 kg 14.
6. Technical Specifications Note lease notice that your display works P best at native resolution of 3840 x 2160 @ 60Hz. For best display quality, please follow this resolution recommendation. 6.1 Resolution & Preset Modes Maximum Resolution 3840 x 2160 @ 60 Hz (digital input) Recommended Resolution 3840 x 2160 @ 60 Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 37.
7. Power Management 7. Power Management If you have VESA DPM compliance display card or software installed in your PC, the display can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the display will 'wake up' automatically.
8. Customer care and warranty together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 8. Customer care and warranty 8.1 Philips’ Flat Panel Displays Pixel Defect Policy Philips strives to deliver the highest quality products.
8. Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
8. Customer care and warranty Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
8. Customer care and warranty 8.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center. For Warranty Period please refer to Warranty Statement in Important Information Manual.
9. Troubleshooting & FAQs 9. Troubleshooting & FAQs • Check to see if the display cable has bent pins. • Make sure the computer is turned on. 9.1 Troubleshooting AUTO button doesn't function This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. • Note The Auto Function is not applicable in DVI-Digital mode as it is not necessary.
9. Troubleshooting & FAQs • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode. may result in severe “burn-in” or “after-image” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Horizontal flicker appears Image appears distorted. Text is fuzzy or blurred. • Adjust the image using the “Auto” function in OSD Main Controls.
9. Troubleshooting & FAQs in your user manual to install the drivers. Your computer may ask you for display drivers (.inf and .icm files) or a driver disk when you first install your display. 9.2 General FAQs Q1: When I install my display what should I do if the screen shows 'Cannot display this video mode'? Q4: How do I adjust the resolution? Ans.: Recommended resolution for this display: 3840 x 2160 @ 60 Hz. • Unplug all cables, then connect your PC to the display that you used previously.
9. Troubleshooting & FAQs • Press "OK" to show the OSD (On Screen Display) menu Q10: Are Philips LCD displays Plugand- Play? • Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below. 1. Color Temperature: Native, 5000K, 6500K, 7500K, 8200K, 9300K and 11500K. With settings in the 5000K range the panel appears "warm, with a redwhite color tone", while a 11500K temperature yields "cool, bluewhite toning". Ans.
9. Troubleshooting & FAQs Q13: How to unlock/lock my hot key? 9.3 Multiview FAQs Ans.: Please press for 10 seconds to unlock/lock the hot key, by doing so, your display pops out “Attention” to show the unlock/lock status as shown below illustrators. Q1: How to listen to Audio, independent of video? Ans.: Normally the audio source is linked to the main picture source.
2019 © TOP Victory Investment Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
