Color Television Operating Instructions
TABLE OF CONTENTS Introduction Safety Information/Useful Tips .................................................................................................. 3 Before Calling Service ................................................................................................................. 4 Basic Installation/Functions Hooking Up Your TV (Basic Connection) ............................................................................... 5 Use/Care of remote Control ..................................
SAFETY INFORMATION AND USEFUL TIPS Safety Information Disconnect mains plug when : the red light below the TV screen is flashing continuously. a bright white line is displayed across the screen. cleaning the TV screen. Never use abrasive cleaning agents. Use a slight damp chamois leather or soft cloth. – there is a lightning storm. – the set is left unattended for a prolonged period of time. • – – – • No naked flame sources, such as lighted candles, should be placed on top of the TV or in the vicinity.
BEFORE CALLING SERVICE Below is a list of frequently occurred symptoms. Before you call for service, make these simple checks. Some of these symptoms can easily be rectified if you know what to do. Symptom What you should do Colour patch (uneveness) • Switch off the TV by the mains power button. Wait for 20 minutes before switching on again. • Check the TV is not placed too near speakers or magnetic objects. No power • Check the TV’s AC power cord is plugged into the mains socket.
HOOKING UP YOUR TV (BASIC CONNECTION) Antenna Connection • Connect the aerial plug to the antenna socket ¬ on the backcover. • Insert the mains plug into the wall socket. Mains Connection • For correct mains voltage, refer to type sticker at the rear of the TV set • Consult your dealer if mains supply is different. Note : This diagram is not representative of the actual plug and socket. Switching on the Set • Press the main power button to switch on/ off the TV.
CONNECTING THE AUDIO/VIDEO SOCKETS (PLAYBACK) Monitor out AV1 in AV2 in VIDEO Y L/Mono S-VIDEO Pb AUDIO R AV sockets on the rear of TV Pr COMPONENT VIDEO INPUT OUT OUT OUT ANTENNA VIDEO R AUDIO L IN IN IN Back of VCR VCR (equipped with Video and Audio output sockets) You can view the playback of VCR tapes (Video Disc players, camcorders, etc.) by using the AUDIO and VIDEO INPUT sockets on the rear of the TV.
CONNECTING THE AUDIO/VIDEO SOCKETS (PLACKBACK) Monitor out AV1 in AV2 in VIDEO AV sockets on rear of TV Y L/Mono AUDIO R Pr COMPONENT VIDEO INPUT OUT Y Pb S-VIDEO Pb OUT Pr Back of DVD L AUDIO R DVD (Equipped with “Y”, “Pb” and “Pr” and Output sockets) You can view the playback of DVD discs by using the COMPONENT VIDEO INPUT sockets on the rear of the TV.
CONNECTING THE AUDIO/VIDEO SOCKETS (RECORDING) Connection for recording from the TV channel Monitor out AV1 in AV sockets on the rear of TV AV2 in VIDEO Y L/Mono S-VIDEO Pb AUDIO R Pr COMPONENT VIDEO INPUT OUT OUT OUT ANTENNA VIDEO R AUDIO L IN IN IN VCR (equipped with Video and Audio input sockets) – Connect the corresponding INPUT sockets of the VCR to the MONITOR OUTPUT sockets on the rear of the TV.
FUNCTIONS OF REMOTE CONTROL & Power button – Switch set off temporarily to standby mode. & (The red light indicator lights up when the set is on standby mode). é – To switch on set from standby mode, press “ Channel +/– , Digit (0 -9) or Power button. é Teletext Colour/Personal Zapping buttons ‘ – In teletext mode, the colour buttons allow you to ( access directly an item or corresponding pages. § – As Personal Zapping buttons, you can surf up to è 10 personal channels for each button.
FUNCTIONS 3 4 5 6 7 8 9 20 21 22 23 24 25 OF REMOTE CONTROL 3 Main Index Button In teletext mode, press button to return to the main index page. 4 Frownie button Allows to delete stored personal preference channels in your Personal Preference list. For detailed description of functions, refer to section on “Personal Zapping ”. 5 Smart Picture Button Press the Smart Picture button repeatedly to access 5 different types of picture settings and choose your desired setting.
FUNCTIONS OF TV CONTROLS 1 2 3 4 5 6 7 1 Mains Power button Switch mains power on or off. 2 Standby Light indicator Indicate red light when standby mode is activated. Remote Sensor Acts as a sensor for activating the controls of the TV when remote control handset is aimed at it. Volume - button Adjust sound volume softer. Volume + button Adjust sound volume louder. Programme button Select channel in ascending order. Programme button 5 Select channel in descending order.
SELECTING THE MENU LANGUAGE Operating instructions generally explains the operation of the TV set using the buttons on the remote control unless otherwise stated. Please read the following instructions carefully and follow the steps as shown to familiarise yourself with the installations and all features available in your set. Note: When there is no signal input to the TV, you may encounter instability of the on screen display.
AUTOMATIC TUNING OF CHANNELS Automatic tuning of channels allows you to store each programme automatically. Step Press button MENU Result on screen Enter main menu. Main ✔ Picture ■ Sound ■ Features ■ Install o π Brightness Colour Contrast Sharpness Colour Temp. More... œ ¸ Press button repeatedly until Install is selected.
MANUAL TUNING OF CHANNELS Manual tuning of channels allows you to select your preferred channel number for every available programme. Step Press button MENU Result on screen Main ✔ Picture ■ Sound ■ Features ■ Install Enter main menu. o π Brightness Colour Contrast Sharpness Colour Temp. More... œ ¸ Press button repeatedly until Install is selected.
MANUAL TC UNING HANNELS OF CHANNELS Step Press button Start manual searching. Searching stops once a transmitting signal is found. ˙ ¸ 9 1 4 7 10 11 12 2 5 8 0 ¸ ˙ m Result on screen Select Channel. 3 6 9 Key in the channel number. Press button repeatedly until Store is selected. Store tuned channel. Note : If you want to continue searching for another transmitting channel, repeat steps 7 to 11. Exit menu from screen.
SELECTING THE COLOUR/SOUND SYSTEM This feature allows you to select your desired Colour and Sound system. If Auto is selected, the respective colour and sound system will be automatically selected according to the transmission system. Note : Select your desired colour and sound system manually if reception is poor at Auto mode. Step Press button Repeat step 1 to step 5 as in “Manual Tuning of TV Channels” Result on screen Colour System is selected.
FINE TUNING OF CHANNELS This feature allows you to adjust picture reception in areas of weak reception. Step Press button MENU Result on screen Enter main menu. Main ✔ Picture ■ Sound ■ Features ■ Install o π Brightness Color Contrast Sharpness Colour Temp. More... œ ¸ Press button repeatedly until Install is selected. Main ■ Picture ■ Sound ■ Features ✔ Install o π Language Auto Store Manual Store Channel Edit œ ˙ ¸ ˙ ¸ ˙ or Enter install menu.
EDITING OF CHANNELS This feature allows you to skip or edit channels which have bad or weak TV signal or channels that you do not watch often. Note : Once a channel is skipped, you cannot have access to it by the CH (Channel) + or – button.You can only have access to the channel by the Digit (0 -9) buttons. Step Press button Result on screen Enter main menu. MENU Press button repeatedly until Install is selected.
ADJUSTING THE TV PICTURE The picture menu allows you to make adjustments to the picture. Step Press button MENU ˙ ˚ Result on screen Display the main menu on screen. Enter Picture menu. Select item. or ¸ ˝ or Adjust level or select desired setting. ˙ m o π Brightness Colour Contrast Sharpness Colour Temp More...
ADJUSTING THE TV SOUND The sound menu allows you to make adjustments to the sound. Step Press button Result on screen Display the main menu on screen. MENU ¸ Select Sound menu. Main ✔ Picture ■ Sound ■ Features ■ Install o π Brightness Colour Contrast Sharpness Colour Temp. More... œ Main o ■ Picture Treble Boost ✔ Sound π Bass Boost ■ Features AVL ■ Install œ ˙ ˚ Enter Sound menu. Sound o ✔ Treble Boost ■ Bass Boost ■ AVL Select item. On or ¸ ˝ or œ Adjust level or select desired setting.
USING THE SCREEN FORMAT You can have a choice of two formats for your viewing pleasure, namely : - 4:3 mode and the EXPAND 4:3 mode through the FORMAT menu. Step Press button MENU ¸ Result on screen Display the main menu on screen. Press button repeatedly until Features is selected. Main ■ Picture ■ Sound ✔ Features ■ Install o Format Signal Strength π œ ˙ ¸ ˙ m Enter the Features menu. Feature o ✔ Format ■ Signal strength 4:3 π Press button repeatedly until Format is selected.
ACTIVATING THE SIGNAL STRENGTH The Signal Strength feature allows to view the signal strength level when the On option is selected. The signal strength level will be indicated at the bottom of the screen whenever you switch channel. Step Press button MENU ¸ Result on screen Display the main menu on screen. Press button repeatedly until Signal Strength is selected.
SMART PICTURE CONTROL Whether you are watching a movie or video game, your TV has automatic video control settings matched to your current program source or content. The Smart Picture feature quickly resets your TV’s video controls of program for a number of different types of programs and viewing conditions you may have in your home. Each Smart Picture setting is preset at the factory to automatically adjust the TV’s Brightness, Colour, Picture and Sharpness levels.
SMART SOUND CONTROL Whether you are watching a movie or video game, your TV has automatic sound control settings matched to your current program source or content. The Smart Sound feature quickly resets your TV’s sound controls of program for a number of different types of programs and viewing conditions you may have in your home. Each Smart Sound setting is preset at the factory to automatically adjust the TV’s Treble and Bass levels.
PERSONAL ZAPPING A list or series of favourite TV programs can be selected and stored in the 4 coloured buttons with the Personal Zapping feature. With this feature you can easily viewed up to a total of 10 preferred channels for each coloured button. Adding Channels to the Favourite list Step Press button 1 4 7 2 5 8 0 3 6 9 Result on screen Select a channel by the Digit buttons 8 Press button to display list. 8 Choose your favourite colour button to store selected channel.
USING THE TELETEXT If a TV channel broadcast contains teletext information, each channel that broadcasts teletext transmits a page (index page) with information on how to use the teletext system, usually on page 100. The system transmitted is indicated in the option line at the bottom of the screen.
USING THE TELETEXT Press button § Interrupt § è ! ç a è Enlarge h ! Hold f ç Reveal/ Conceal e 27 Result on screen Press the button to change to TV mode. Press the button again to return to teletext mode and to the teletext page. Press the button once to enlarge and view the top half of the page. Press the button the second time to enlarge and view the bottom half of the page. Press the button the third time to return to normal size page. A selected page sometimes contains a few sub-pages.
SPECIFICATIONS 29PT5221, 29PT5342 Picture tube screen size 705 mm Picture tube visible area 675 mm Audio Output : Speaker 2 x 5 W (29PT5221), 2 x 10 W (29PT5342) TV System NTSC M PAL B/G PAL B/H (only for certain versions) PAL D/K PAL I SECAM B/G SECAM D/K SECAM K1 Playback System NTSC 3.58, NTSC 4.43, PAL 60 Set Dimensions : Width Depth Height 736 mm 490 mm 580 mm Net Weight of Set (approximate ) 45.
313 9125 36802 29
