Specifications
Alignments
EN 79L05U AA 8.
Option Byte 4 (OP4)
• OB47: OP_COMPRESS_16_10
– 0 : Compress mode is not used.
– 1 : Compress mode is used.
• OB46: OP_OPTIMISED_START
– Not applicable. Default setting is “0”.
• OB45: ULTRA BASS
– 0 : Ultra Bass is disabled or not applicable.
– 1 : Ultra Bass is enabled.
– Default setting is “0”.
• OB44: DELTA VOLUME
– 0 : Delta Volume Level is disabled or not applicable.
– 1 : Delta Volume Level is enabled.
• OB43: Reserved
– Default setting is “0”.
• OB42: VOLUME LIMITER
– 0 : Volume Limiter Level is disabled or not applicable.
– 1 : Toggle Volume Limiter Level is enabled.
• OB41: Reserved
– Default setting is “0”.
• OB40: STEREO NICAM 2CS
– 0 : For AV Stereo.
– 1 : For NICAM Stereo 2CS.
Option Byte 5 (OP5)
• OB57: AV1
– 0 : AV1 source is not present.
– 1 : AV1 source is present.
• OB56: AV2
– 0 : AV2 source is not present.
– 1 : AV2 source is present.
– Note : For EU, when AV2=“1”, both EXT2 and SVHS2
should be included in the OSD loop.
• OB55: AV3
– 0 : Side/Front AV3 source is not present.
– 1 : Side/Front AV3 source is present.
• OB54: CVI
– 0 : CVI source is not available.
– 1 : CVI source is available.
• OB53: SVHS2
– 0 : SVHS2 source is not available.
– 1 : SVHS2 source is available.
– Note : This option bit is not applicable for EU.
• OB52: SVHS3
– 0 : SVHS3 source is not available.
– 1 : SVHS3 source is available.
– Note : This option bit is not applicable for EU.
• OB51: HOTEL MODE
– 0 : Hotel mode is disabled or not applicable.
– 1 : Hotel mode is enabled.
• OB50: Reserved
– Default setting is “0”.
Option Byte 6 (OP6)
• OB67: PERSONAL ZAPPING
– 0 : Personal Zapping feature is disabled or not
applicable.
– 1 : Personal Zapping feature is enabled.
• OB66: OP_SMART_SURF
– 0 : Smart Surf key is not used on remote control.
– 1 : Smart Surf key is used on remote control.
• OB65: FM TRAP
– 0 : FM Trap is not present.
– 1 : FM Trap is present.
– Note: Only for LATAM region.
• OB64: COMBFILTER
– 0 : 3D-combfilter is not present.
– 1 : 3D-combfilter is present.
• OB63: ACTIVE CONTROL
– 0 : Active Control feature is disabled or not applicable.
– 1 : Active Control feature is enabled.
• OB62: VIDEO TEXT
– 0 : Video Text (DW with TXT) is disabled or not
applicable.
– 1 : Video Text (DW with TXT) is enabled.
– Note: For EU only.
• OB61: LIGHT SENSOR
– 0 : Light sensor feature is disabled or not applicable.
– 1 : Light sensor feature is enabled.
• OB60: DUAL TEXT
– 0 : Dual Text and Text Dual Screen are disabled or not
applicable.
– 1: Dual Text and Text Dual Screen are enabled.
Option Byte 7 (OP7)
• OB77: TIME WIN1
– 00 : The time window is set to 1.2 s.
– 01 : The time window is set to 2 s.
– Note :The time-out for all digit entries depends on this
setting.
• OB76: OP_MALAY
– For AP only. Default setting is “0”.
• OB75: OP_THAI
– For AP only. Default setting is “0”.
• OB74: OP_SIGNAL_STRENGTH
– For AP only. Default setting is “0”.
• OB73: Reserved
– Default setting is “0”.
• OB72: Reserved
– Default setting is “0”.
• OB71: Reserved
– Default setting is “0”.
• OB70: Reserved
– Default setting is “0”.
8.3.2 Tuner
Note: Described alignments are only necessary when the NVM
(item 7601) is replaced.
IF PLL
This adjustment is auto-aligned. Therefore, no action is
required.
AGC (AGC take over point)
1. Set the external pattern generator to a color bar video
signal and connect the RF output to aerial input. Set
amplitude to 10 mV and set frequency to 61.25 MHz
(channel 3).
2. Connect a DC multimeter to pin 1 of the tuner (item 1000
on the main panel).
3. Activate the SAM.
4. Go to the TUNER sub menu.
5. Select AGC with the UP/DOWN cursor keys.
6. Adjust the AGC-value with the LEFT/ RIGHT cursor keys
until the voltage at pin 1 of the tuner lies between 3.8 and
2.3 V (default value is “20”).
7. Switch the set to STANDBY, in order to store the
alignments.
CL (Cathode drive level)
Always set to “5”.
8.3.3 White Tone
In the WHITE TONE sub menu, the values of the black cut off
level can be adjusted. Normally, no alignment is needed, and
you can use the given default values.
The color temperature mode (NORMAL, COOL and WARM)
and the color (R, G, and B) can be selected with the UP/DOWN
RIGHT/LEFT cursor keys. The value can be changed with the
LEFT/RIGHT cursor keys. First, select the values for the
NORMAL color temperature. Then select the values for the
COOL and WARM mode. After alignment, switch the set to
STANDBY, in order to store the alignments.
Default settings:
L05U_AA_312278515051.book Page 79 Friday, March 4, 2005 10:42 AM