Specifications
Table Of Contents
- Contents
- 1. Technical Specifications, Connections, and Chassis Overview
- 2. Safety Instructions, Warnings, and Notes
- 3. Directions for Use
- 4. Mechanical Instructions
- 5. Service Modes, Error Codes, and Fault Finding
- 6. Block Diagrams, Testpoint Overviews, and Waveforms
- 7. Circuit Diagrams and PWB Layouts
- Mono Carrier: Power Supply
- Mono Carrier: Deflection
- Mono Carrier: Tuner IF
- Mono Carrier: Video Processing
- Mono Carrier: Audio Processing
- Mono Carrier: Audio Amplifier
- Mono Carrier: Font I/O + Control + HP
- Mono Carrier: Rear I/O Cinch
- Mono Carrier: Diversity Table for Rear I/O
- Mono Carrier: DVD Power Supply (Optional)
- Layout Mono Carrier: (Top Side)
- Layout Mono Carrier (Overview Bottom Side)
- Layout Mono Carrier (Part 1 Bottom Side)
- Layout Mono Carrier (Part 2 Bottom Side)
- Layout Mono Carrier (Part 3 Bottom Side)
- Layout Mono Carrier (Part 4 Bottom Side)
- CRT Panel
- Layout CRT Panel (Top Side)
- Layout CRT Panel (Bottom Side)
- Top Control Panel
- Layout Top Control Panel (Top Side)
- Layout Top Control Panel (Bottom Side)
- 8. Alignments
- 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets
- 10. Spare Parts List
- 11. Revision List
Directions for Use
EN 7L03.1U AA 3.
3. Directions for Use
8
CABLE
IN
TO
TV
VIDEO
OUT
LR
AUDIO
OUT
3 4
OUTPUT
CH
TO TV
CABLE
IN
3
1
2
ANT 75‰
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
24
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
ANT 75‰
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
4
5
6
OUTPUT
CH
3 4
Cable Box Connection (RF Input/Output Only):
Jack Panel Back of Cable Box
Cable Signal
IN from the
Cable
Company
Round 751
Coaxial Cable
Jack Panel Back of TV
Cable Box Connection (with Audio/Video Outputs):
Cable Signal IN from
the Cable Company
Jack Panel Back
of Cable Box
Cable Box with
Audio/Video Outputs
RCA type Audio
Left and Right
Cables
Jack Panel Back of TV
I
f you cable signal uses a cable box or
decoder, follow the easy steps below to
complete the connection.
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound
to the TV. The sound from the cable box will
be mono.
1
Connect the open end of the round
Cable Company supplied cable to
the
cable signal IN(put) plug on the back
of the Cable Box.
2
Using a separate round coaxial cable,
connect one end to the OUT(put) (TO
TV) plug on the back of the Cable
Box.
3
Connect the other end of the round
coaxial cable to the 751 input on the
back of the television. Screw it down
finger tight.
NOTE: Be sure to set the OUTPUT CHAN-
NEL SWITCH on the back of the cable box to
CH 3 or 4, then tune the cable box on the TV
to the corresponding channel. Once tuned,
change channels at the cable box, not the tele-
vision.
Cable Box (w/Audio/Video
Outputs):
This connection will supply Stereo sound to the
TV.
4
Connect the open end of the round
Cable Company supplied cable to
the
cable signal IN(put) plug on the back
of the Cable Box.
5
Using a RCA type Video Cable, connect
one end of the cable to the Video (or
ANT, your cable box may be labeled dif-
ferently) Out jack on the cable box and
the other end to the AV1 Video Input on
the TV.
6
Using a RCA type Audio Left and Right
Cable, connect one end to the left and
right Audio Out L & R jacks on the
cable box. Connect the other end to the
AV1 Audio L & R Input jacks on the TV.
NOTE: Use the Channel +, or – buttons on the
TV remote control to tune to the AV1 channel
for the cable box signal. Once tuned, change
channels at the cable box, not the television.
B
ASIC
C
ABLE
B
OX
/D
ECODER
C
ONNECTION
RCA type Video Cable
7
1
ANT 75‰
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
Y
our Cable TV input into your home may
be a single (75 ohm) cable. If so, this con-
nection is very simple. Follow the steps below
to connect your cable signal to your new tele-
vision.
Direct Cable Connections:
1
Connect the open end of the round
Cable Company supplied cable to the
751 input on the TV. Screw it down fin-
ger tight.
B
ASIC
C
ABLE
T
ELEVISION
C
ONNECTION
BACK OF TV
Direct Cable Connection:
Cable signal coming
from Cable
Company (Round
751 coaxial cable)
Jack Panel Back of TV
A
combination antenna receives normal
broadcast channels (VHF 2–13 and
UHF 14–69). Your connection is easy
because there is only one 751 (ohm)
antenna plug on the back of your TV, and
that’s where the antenna goes.
1
If your antenna has a round cable
(75 ohm) on the end, then you're ready
to connect it to the TV.
If your antenna has flat, twin-lead
wire (300 ohm), you first need to
attach the antenna wires to the screws
on a 300- to 75-ohm adapter.
2
Push the round end of the adapter (or
antenna) onto the 751 (ohm) plug on
the back of the TV. If the round end of
the antenna wire is threaded, screw it
down finger tight.
B
ASIC
A
NTENNA
T
ELEVISION
C
ONNECTION
Use the AutoProgram Control to add all avail-
able channels into the TV’s memory, then
press the CH + and – buttons to scroll the
channels.
c
C
HECK
I
T
O
UT
1
2
ANT 75‰
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
Back of TV
Round 751
Coaxial Cable
from Antenna
Twin
Lead Wire
300 to 75-ohm
Adapter
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna receives normal
broadcast channels 2-13 (VHF) and 14-69 (UHF).
Antenna Connection:
Jack Panel
Back of TV
Use the AutoProgram Control to add all avail-
able channels into the TV’s memory, then
press the CH + and – buttons to scroll the
channels.
c
C
HECK
I
T
O
UT