Specifications
Table Of Contents
- Contents
- 1. Technical Specifications, Connections, and Chassis Overview
- 2. Safety Instructions, Warnings, and Notes
- 3. Directions for Use
- 4. Mechanical Instructions
- 5. Service Modes, Error Codes, and Fault Finding
- 6. Block Diagrams, Testpoint Overviews, and Waveforms
- 7. Circuit Diagrams and PWB Layouts
- Mono Carrier: Power Supply
- Mono Carrier: Deflection
- Mono Carrier: Tuner IF
- Mono Carrier: Video Processing
- Mono Carrier: Audio Processing
- Mono Carrier: Audio Amplifier
- Mono Carrier: Font I/O + Control + HP
- Mono Carrier: Rear I/O Cinch
- Mono Carrier: Diversity Table for Rear I/O
- Mono Carrier: DVD Power Supply (Optional)
- Layout Mono Carrier: (Top Side)
- Layout Mono Carrier (Overview Bottom Side)
- Layout Mono Carrier (Part 1 Bottom Side)
- Layout Mono Carrier (Part 2 Bottom Side)
- Layout Mono Carrier (Part 3 Bottom Side)
- Layout Mono Carrier (Part 4 Bottom Side)
- CRT Panel
- Layout CRT Panel (Top Side)
- Layout CRT Panel (Bottom Side)
- Top Control Panel
- Layout Top Control Panel (Top Side)
- Layout Top Control Panel (Bottom Side)
- 8. Alignments
- 9. Circuit Descriptions, List of Abbreviations, and IC Data Sheets
- 10. Spare Parts List
- 11. Revision List
Directions for Use
EN 10 L03.1U AA3.
10
VOL
AV2
CVI
AV1
24
Front
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
AUDIO OUT
L R
S-VIDEO
OUT
ANT/CABLE
OUT
VIDEO
OUT
SVHS
1
2
3
4
5
7
6
T
he S(uper)-Video connection on the rear
of the TV can provide you with better pic-
ture detail and clarity for the playback of
accessory sources such as DBS (digital
broadcast satellite), DVD (digital video
discs), video games, and S-VHS VCR (video
cassette recorder) tapes than the normal
antenna picture connections.
NOTE: The accessory device must have an
S-VIDEO OUT(put) jack in order for you to
complete the connection on this page.
1
Connect one end of the S-VIDEO
CABLE to the S-VIDEO jack on the
back of the TV.
2
Connect other end of the S-VIDEO
CABLE to the S-VIDEO OUT jack on
the back of the VCR.
3
Connect one end the AUDIO (red
and white) CABLES to the AV2 in
AUDIO L and R(left and right) jacks
on the rear of the TV.
4
Connect the other ends of the AUDIO
(red and white) CABLES to the
AUDIO (left and right) OUT jacks on
the rear of the VCR.
5
Turn the VCR and the TV ON.
6
Press the AV button on the remote to
scroll the channels until SVHS appears
in the upper left corner of the TV
screen.
7
Now your ready to place a prerecorded
video tape in the VCR and press the
PLAY
button
.
U
SING THE
S-V
IDEO
I
NPUT
J
ACKS
The S-VIDEO and VIDEO AV2 in(puts) are
in parallel. The S-VIDEO input is domi-
nant when in use. If separate video signals
are connected to the S-VIDEO and VIDEO
AV2 in(puts), the signal from the VIDEO
AV2 in(put) will not be usable.
Note: The S-Video and Audio cables needed
for this connection are not supplied with
your TV. Please contact your dealer or
Philips at 800-531-0039 for information
about purchasing the needed cables.
H
ELPFUL
H
INT
AUDIO CABLE
(RED/WHITE)
VCR
(EQUIPPED WITH
S-VIDEO JACKS)
S-VIDEO
CABLE
BACK OF VCR
NOTE: Repeatedly pressing the AV button on the remote control will toggle the
picture source from the current channel, then the AV1 channel (or CVI channel),
then the AV2 channel, then the S-Video (SVHS) channel, then back to the current
channel being watched.
9
VOL
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 i n
AUDIO
R
COMPONENT VIDEO INPUT
24
SVHS
CVI
AV1
AUDIO OUT
R L
S-VIDEO
OUT
ANT/CABLE
OUT
VIDEO
OUT
3
AUDIO OUT
R L
S-VIDEO
OUT
ANT/CABLE
OUT
VIDEO
OUT
3
4
5
7
1
6
AV2
2
4
2
1
5
7
T
he TV’s audio/video input jacks are for
direct picture and sound connections
between the TV and a VCR (or similar device)
that has audio/video output jacks. Both the
AV1 and AV2 Input Jack connections are shown
on this page, but either one can be connected
alone. Follow the easy steps below to connect
your accessory device to the AV1 and AV2 in
Jacks located on the back of the TV.
1
Connect the VIDEO (yellow) cable to
the VIDEO AV1 in (or AV2 in) jack on
the back of the TV.
2
Connect the AUDIO (red and white)
cables to the AUDIO (left and right)
AV1 in (or AV2 in) jacks on the rear of
the TV.
3
Connect the VIDEO (yellow) cable to
the VIDEO OUT jack on the back of
the VCR (either one or two) or acces-
sory device being used.
4
Connect the AUDIO (red and white)
cables to the AUDIO (left and right)
OUT jacks on the rear of the VCR
(either one or two) or accessory device
being used.
5
Turn the VCR (either one or two) or
accessory device and the TV ON.
6
Press the AV button on the remote
control to select the AV1 channel for
accessory device number one, or the
AV2 channel for accessory device
number two. AV1 or AV2 will appear
in the upper left corner on the TV
screen depending on the channel cho-
sen.
7
With either of the VCRs (or accessory
devices) ON and a prerecorded tape
(CD, DVD, etc.) inserted, press the
PLAY button to view the tape on the
television.
U
SING THE
AV1
IN OR
AV2
IN
(I
NPUT
) J
ACKS
Repeatedly pressing the AV button on the
remote control will toggle the picture source
from the current channel, then AV1 (or CVI),
AV2, SVHS, or current channel.
Note: The Audio/Video cables needed for
this connection are not supplied with your
TV. Please contact your dealer or Philips at
800-531-0039 for information about purchas-
ing the needed cables.
c
C
HECK
I
T
O
UT
AUDIO IN
(RED/WHITE)
VCR TWO (or accessory device)
(EQUIPPED WITH VIDEO AND
AUDIO OUTPUT JACKS)
VIDEO IN
(YELLOW)
BACK OF VCR
NOTE: Repeatedly pressing the AV button on the remote control will toggle the
picture source from the current channel, then the AV1 channel (or CVI channel),
then the AV2 channel, then the S-Video (SVHS) channel, then back to the current
channel being watched.
BACK OF TV
AV 1
Connection
AV 2
Connection
VCR ONE (or accessory device)
(EQUIPPED WITH VIDEO AND
AUDIO OUTPUT JACKS)