B Line 278B1 www.philips.
Table of Contents 1. Important �������������������������������������� 1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the monitor �������������� 5 2.1 Installation ������������������������������������ 5 2.2 Operating the monitor ���������������7 2.3 Remove the Base Assembly for VESA Mounting ��������������������������10 3.
1. Important 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor.
1. Important • degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will not be covered under warranty. use it for a longer lifetime, please use the monitor in a location that falls within the following temperature and humidity ranges. Do not knock or drop the monitor during operation or transportation.
1. Important in Regulation & Service Information Manual.) • For transportation information, please refer to “Technical Specifications”. • Do not leave your monitor in a car/ trunk under direct sun light. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document. Notes, Cautions and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. 2.1 Installation Package contents B Line 278B1 Quick Start Register your product and get support at www.philips.com/welcome 2. Hold the stand with both hands. (1) Gently attach the base to the stand. Monitor User’s Manual 使用产品前请阅读使用说明 (2) Use your fingers to tighten the screw located at the bottom of the base.
2. Setting up the monitor Connecting to your PC 278B1N 278B1 Fast Charger 1 2 3 1 2 4 5 6 3 4 5 6 9 7 8 7 10 USB UP 1 Power Switch USB hub 2 AC power input 2 3 HDMI 1 input 4 HDMI 2 input 5 DisplayPort input USB A-B 1 6 Audio output USB UP 7 Kensington anti-theft lock 1 Power Switch Connect to PC 2 AC power input 1. Connect the power cord to the back of the monitor firmly. 3 HDMI 1 input 2. Turn off your computer and unplug its power cable.
2. Setting up the monitor 4 USB charging 2.2 Operating the monitor Description of the control buttons This display has USB ports capable of standard power output including some with USB Charging function (identifiable with power icon ). You can use these ports to charge your Smart phone or power your external HDD, for example. The display must be powered ON at all times to be able to use this function.
2. Setting up the monitor Description of the On Screen Display Note What is On-Screen Display (OSD)? If this display has "DPS" for ECO design, the default setting is "ON" mode: it makes the screen looks slightly dim; for optimum brightness, enter to the OSD to set "DPS" to "OFF" mode. On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor Height adjustment Resolution notification This monitor is designed for optimal performance at its native resolution, 3840 x 2160. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 3840 x 2160 for best results. Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. 100mm 100mm 2. Place the monitor face down on a smooth surface.
3. Image Optimization 3. Image Optimization 1. Press to launch the SmartImage on screen display. 3.1 SmartImage 2. Keep pressing to toggle among EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode, SmartUniformity, Off. What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time.
3. Image Optimization • • Photo: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors. around 75-80%. By enabling Philips SmartUniformity feature, display uniformity is incr eased to above 95%. This produces more consistent and true images.
3. Image Optimization 3.2 SmartContrast What is it? Unique technology that dynamically analyzes displayed content and automatically optimizes a Monitor's contrast ratio for maximum visual clarity and viewing enjoyment, stepping up backlighting for clearer, crisper and brighter images or dimming backlighting for clear display of images on dark backgrounds. Why do I need it? You want the very best visual clarity and viewing comfort for every type of content.
4. PowerSensor™ 4. PowerSensor™ • • • How does it work? PowerSensor works on principle of transmission and reception of harmless “infrared” signals in order to detect user-presence. When the user is in front of the monitor, the monitor operates normally, at the predetermined settings that the user has set- i.e. brightness, contrast, color, etc • from the monitor use the maximum detection signal for distances up to 120 cm or 47 inches.
4. PowerSensor™ returned to its default Landscape position. Note A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled. If you find that the PowerSensor is excessively sensitive to nearby motion for some reason, please adjust to a lower signal strength. Keep sensor lens clean, if the sensor lens is dirty, wipe it with alcohol to avoid reducing of distance detection .
5. Designs to prevent computer vision syndrome • Gently stretch your neck, and slowly tilt your head forward, backward, side for pain relief. 3. Ideal working posture 5. Designs to prevent computer vision syndrome (CVS) • Reposition your screen to appropriate height and angle according to your height. 4. Choose Philips monitor for easy-oneyes. Philips monitor is designed to prevent eye strain caused by prolonged computer use.
6.Technical Specifications 6. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio(typ.) Optimum Resolution Viewing Angle Display Colors Flicker Free Picture Enhancement Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode SmartUniformity Delta E EasyRead Connectivity IPS Technology W-LED 27" W (68.6 cm) 16:9 0.1554 (H) mm x 0.1554 (V) mm 1000:1 3840 x 2160 @ 60 Hz 178° (H) / 178° (V) @ C/R > 10 (typ.) 1.
6.
6.Technical Specifications Relative humidity (Non-operation) Atmospheric pressure (Non-operation) Environmental and energy ROHS Packaging Specific Substances Cabinet Color Finish 10% to 90% 500 to 1060hPa YES 100% recyclable 100% PVC BFR free housing Black Texture Note 1. This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet. 2. SmartUniformity and Delta E information sheets are included in the box.
6.Technical Specifications 6.1 Resolution & Preset Modes Maximum Resolution 3840 x 2160 @ 60 Hz Recommended Resolution 3840 x 2160 @ 60 Hz H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 35.16 800 x 600 56.25 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.08 800 x 600 72.19 47.73 832 x 624 74.55 48.36 1024 x 768 60.00 56.48 1024 x 768 70.07 60.02 1024 x 768 75.03 44.
7.Power Management 7. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
8.Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 8. Customer care and warranty 8.
8.Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
8.
8.Customer care and warranty 8.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For Warranty Period please refer to Warranty Statement in Regulation & Service Information Manual.
9.Troubleshooting & FAQs • 9. Troubleshooting & FAQs AUTO button doesn't function • 9.1 Troubleshooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Visible signs of smoke or sparks No Picture (Power LED not lit) Make sure the power cord is plugged into the power outlet and into the back of the monitor.
9.Troubleshooting & FAQs Horizontal flicker appears damage mentioned above is not covered under your warranty. Image appears distorted. Text is fuzzy or blurred. • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
9.Troubleshooting & FAQs tab. Under the setting tab, in box labelled 'desktop area', move the sidebar to 3840 x 2160 pixels. • Open 'Advanced Properties' and set the Refresh Rate to 60 Hz, then click OK. • Restart your computer and repeat step 2 and 3 to verify that your PC is set at 3840 x 2160. • Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor. • Turn on your monitor and then turn on your PC. Q2: Q5: Is the LCD screen resistant to scratches? Ans.
9.Troubleshooting & FAQs 3. User Define: The user can choose his/her preference color setting by adjusting red, green, blue color. gradually over a period of time after the power has been switched off. Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your LCD monitor will display unchanging static content. Note A measurement of the color of light radiated by an object while it is being heated.
9.Troubleshooting & FAQs Q13: Where can I find Regulation & Service Information Manual mentioned in EDFU? Ans.: Regulation & Service Information Manual can be download on the Philips website support page.
2021 © TOP Victory Investments Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
