S Line 272S1 www.philips.
Table of Contents 1. Important ���������������������������������������� 1 1.1 Safety precautions and maintenance �����������������������������������1 1.2 Notational Descriptions ���������������3 1.3 Disposal of product and packing material ���������������������������������������������4 2. Setting up the monitor ��������������� 5 2.1 Installation ���������������������������������������5 2.2 Operating the monitor �����������������7 2.
1. Important • 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor.
1. Important • • Do not subject the monitor to severe vibration or high impact conditions during operation. within the following temperature and humidity ranges. • Temperature: 0-40°C 32-104°F Do not knock or drop the monitor during operation or transportation. • Humidity: 20-80% RH Important information for Burn-in/ Ghost image Maintenance • • • • • • • • • To protect your monitor from possible damage, do not put excessive pressure on the LCD panel.
1. Important • Do not leave your monitor in a car/ trunk under direct sun light. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document. Note Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to take when the operating instructions given in this manual have been followed.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. 2.1 Installation Package contents S Line 272S1 Quick Start Register your product and get support at www.philips.com/welcome 2. Hold the stand with both hands. (1) Gently attach the base to the stand. (2) Use your fingers to tighten the screw located at the bottom of the base.
2. Setting up the monitor 4 USB charging Connecting to your PC This display has USB ports capable of standard power output including some with USB Charging function (identifiable with power icon ). You can use these ports to charge your Smart phone or power your external HDD, for example. The display must be powered ON at all times to be able to use this function.
2. Setting up the monitor 2 Webcam 2.2 Operating the monitor Description of the control buttons 1 2 3 2 4 1 3 7 6 5 4 2 1 Switch monitor’s power ON and OFF. Microphone Access the OSD menu. Confirm the OSD adjustment. IR of Face identification Adjust the OSD menu. 2.0 Megapixel Webcam Adjust the brightness level. Webcam activity light Change the signal input source. Return to previous OSD level. SmartImage.
2. Setting up the monitor 3 Description of the On Screen Display Main menu LowBlue Mode What is On-Screen Display (OSD)? On Input VGA DVI HDMI 1.4 DisplayPort Picture Audio Adaptive Sync On, Off Picture Format Wide Screen, 4:3 Brightness 0~100 Contrast 0~100 Sharpness 0~100 SmartResponse Off, Fast, Faster, Fastest SmartContrast On, Off Gamma 1.8, 2.0, 2.2, 2.4, 2.
2. Setting up the monitor 4 Resolution notification Height adjustment This monitor is designed for optimal performance at its native resolution, 1920 x 1080. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 x 1080 for best results. Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 100mm 1. Extend the monitor base to its maximum height. 100mm 0° 2. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen.
2. Setting up the monitor Please follow the steps for the setting: 2.4 Built-in Windows Hello™ pop-up webcam 1. Press the built-in webcam in the middle on the top of this monitor. What is it? 1 Philips' innovative and secure webcam pops up when you need it and securely tucks back into the monitor when you are not using it.
2. Setting up the monitor added this, the option for Hello will unlock. d. You'll now see which options are available to set up under Windows Hello. e. Click on "Get started." The setting is complete. Note 1. Please always go to Windows official website to access the latest information, the information in EDFU is subject to change without further notice. 2. Different regions have different voltages, with inconsistent voltage setting may cause water ripple when using this webcam.
3. Image Optimization 3. Image Optimization 1. Press to launch the SmartImage on screen display. 2. Keep pressing to toggle among EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode, Off. 3.1 SmartImage What is it? 3. The SmartImage on screen display will remain on screen for 5 seconds, or you can also press "OK" to make confirmation. There are multiple selections: EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode, Off.
3. Image Optimization • • • • • sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors all without artifacts and faded colors. Note Philips LowBlue mode, mode 2 compliance with TUV Low Blue Light certification, you can have this mode by simply press the hotkey , then press to select LowBlue Mode, see above SmartImage selection steps.
4. Adaptive Sync • AMD Radeon R9 285 • AMD Radeon R7 260X • AMD Radeon R7 260 4. Adaptive Sync ■■ Processor A-Series Desktop and Mobility APUs Adaptive Sync • • • • • • • • • PC gaming has long been an imperfect experience because GPUs and monitors update at different rates. Sometimes a GPU can render many new pictures during a single update of the monitor, and the monitor will show pieces of each picture as a single image. This is called “tearing.
5. Designs to prevent computer vision syndrome 5. Designs to prevent computer vision syndrome (CVS) 3. Ideal working posture • Reposition your screen to appropriate height and angle according to your height. 4. Choose Philips monitor for easy-oneyes. Philips monitor is designed to prevent eye strain caused by prolonged computer use. • Anti-glare screen: Anti-glare screen efficiently reduces annoying and distracting reflections that caused eye fatigue.
6. Technical Specifications 6. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio(typ.) Optimum Resolution Viewing Angle Display Colors Flicker Free Picture Enhancement Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode EasyRead Adaptive Sync Connectivity IPS Technology W-LED 27" W (68.6 cm) 16:9 0.3114 (H) mm x 0.3114 (V) mm 1000:1 1920 x 1080 @ 60 Hz 178° (H) / 178° (V) @ C/R > 10 (typ.) 16.
6.
6.
6. Technical Specifications 6.1 Resolution & Preset Modes Maximum Resolution 1920 x 1080 @ 60 Hz (VGA/DVI) 1920 x 1080 @ 75 Hz (HDMI/DP) Recommended Resolution 1920 x 1080 @ 60 Hz H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.36 1024 x 768 60.00 60.02 1024 x 768 75.03 44.77 1280 x 720 59.86 63.89 1280 x 1024 60.02 79.
7. Power Management 7. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
8. Customer care and warranty together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 8. Customer care and warranty 8.1 Philips’ Flat Panel Monitors Pixel Defect Policy Types of Pixel Defects Philips strives to deliver the highest quality products.
8. Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
8.
8. Customer care and warranty 8.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For Warranty Period please refer to Warranty Statement in Important Information Manual. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center.
9. Troubleshooting & FAQs AUTO button doesn't function 9. Troubleshooting & FAQs • 9.1 Troubleshooting Note The Auto Function is not applicable in DVIDigital mode as it is not necessary. This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.
9. Troubleshooting & FAQs • • Green, red, blue, dark, and white dots appears on the screen Adjust the image using the “Auto” function in OSD Main Controls. Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode. • Image appears blurred, indistinct or too dark • * The "power on" light is too strong and is disturbing Adjust the contrast and brightness on On-Screen Display.
9. Troubleshooting & FAQs • • Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor. from sharp or blunt objects. When handling the monitor, make sure that there is no pressure or force applied to the panel surface side. This may affect your warranty conditions. Turn on your monitor and then turn on your PC. Q2: What is the recommended refresh rate for LCD monitor? Q7: How should I clean the LCD surface? Ans.
9. Troubleshooting & FAQs refresh application if your LCD monitor will display unchanging static content. Note A measurement of the color of light radiated by an object while it is being heated. This measurement is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K.
9. Troubleshooting & FAQs Q15: Why cannot detect my monitor’s Windows Hello webcam, and also Face Recognition option is greyed out? Ans: To fix this issue, you need to proceed following steps to detect the webcam device again: 1. Press Crtl + Shift + ESC to launch the Microsoft Windows Task Manager. 2. Select ‘Services’ tag. 3. Scroll down and select ‘WbioSrvc’ (Windows Biometric Service). If the status shows ‘Running’, right click to stop the service first, then restart the service manually. 4.
2022 © TOP Victory Investments Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
