271S7 www.philips.
Table of Contents 1. Important �����������������������������������������������1 1.1 Safety precautions and maintenance �1 1.2 Notational Descriptions ���������������������������3 1.3 Disposal of product and packing material ���������������������������������������������������������������3 2. Setting up the monitor �����������������������5 2.1 Installation ���������������������������������������������������������5 2.2 Operating the monitor ������������������������������6 2.
1. Important 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor.
1. Important • To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. • If your monitor gets wet, wipe it with dry cloth as soon as possible. • If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center.
1. Important 1.3 Disposal of product and packing material 1.2 Notational Descriptions The following subsections describe notational conventions used in this document. Waste Electrical and Electronic Equipment-WEEE Notes, Cautions and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions or warnings.
1. Important Customers Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. 2.1 Installation Package contents 271S7 271S7 使用 © 2 01 6 Kon 2. Hold the stand with both hands. (1) Gently attach the stand to the VESA mount area until the latch locks the stand. 前请阅读使用说明 User’s Manual Monitor drivers 保留备用 inklijk ilips e Ph .A N.V v er .
2. Setting up the monitor Connect to PC Connecting to your PC 1. Connect the power cord to the back of the monitor firmly. 7 2 3 4 5 2. Turn off your computer and unplug its power cable. 6 3. Connect the monitor signal cable to the video connector on the back of your computer. 1 4. Plug the power cord of your computer and your monitor into a nearby outlet. 5. Turn on your computer and monitor. If the monitor displays an image, installation is complete.
2. Setting up the monitor Description of the On Screen Display Change the signal input source. What is On-Screen Display (OSD)? Return to previous OSD level. On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below: SmartImage hot key.
2. Setting up the monitor The OSD Menu Resolution notification Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. Main menu LowBlue Mode This monitor is designed for optimal performance at its native resolution, 1920 × 1080 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best results.
2. Setting up the monitor Height adjustment 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. 115mm Pivot 2. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. Then lift the monitor stand. 0 90 3. While keeping the release button pressed, tilt the base and slide it out.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation.
2. Setting up the monitor How to enable SmartImage? 3. Image Optimization 3.1 SmartImage What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized monitor performance. 1. Press to launch the SmartImage on screen display. 2.
3. Image Optimization files, scanned articles or other general office applications. • compliance with TUV Low Blue Light certification, you can have this mode by simply press the hotkey , then press to select LowBlue Mode, see above SmartImage selection steps. Photo: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors.
4.Technical Specifications 4. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch SmartContrast Response Time (typ.) SmartResponse Time (typ.) Optimum Resolution Viewing Angle Display Colors Flicker Free Picture Enhancement Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode Connectivity IPS Technology LED 27" W (68.6 cm) 16:9 0.311(H) mm x 0.311(V) mm 20,000,000:1 14 ms(GtG) 5 ms(GtG) 1920 x 1080 @ 60 Hz 178° (H) / 178° (V) @ C/R > 10 16.
4.
4.Technical Specifications EnergyStar Compliance and standards Regulatory Approvals Cabinet Color Finish YES CE Mark, FCC Class B, SEMKO, cETLus, CU-EAC, TCO Edge,TUV-GS,TUV-ERGO, EPA, WEEE, UKRAINIAN,ICES-003,SASO,KUCAS Black/Black Texture Note 1. EPEAT Gold or Silver is valid only where Philips registers the product. Please visit www.epeat.net for registration status in your country. 2. This data is subject to change without notice. Go to www.philips.
4.Technical Specifications 4.1 Resolution & Preset Modes Maximum Resolution 1920 x 1080 @ 60 Hz (analog input) 1920 x 1080 @ 60 Hz (digital input) Recommended Resolution 1920 x 1080 @ 60 Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 35.16 800 x 600 56.25 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.08 800 x 600 72.19 47.73 832 x 624 74.55 48.
5.Power Management 5. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
6.Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 6. Customer care and warranty 6.
6.Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
6.
6.Customer care and warranty Philips Customer Care Center number listed below. • • Local Standard • Warranty Period • Depend on different Regions • • Extended Warranty • Period • + 1 Year + 2 Years • + 3 Years • Total Warranty Period Local Standard warranty period +1 Local Standard warranty period +2 Local Standard warranty period +3 **Proof of original purchase and extended warranty purchase required.
6.Customer care and warranty Poland MSI +48 0223491505 L o c a l c a l l Mon to Fri : 9am tariff 6pm Portugal Mainteq 800 780 902 Free of charge Mon to Fri : 8am 5pm Spain Mainteq +34 902 888 785 € 0.
6.Customer care and warranty Macedonia NA AMC +389 2 3125097 Moldova NA Comel +37322224035 Romania NA Skin +40 21 2101969 Russia NA CPS +7 (495) 645 6746 Serbia&Montenegro NA Kim Tec d.o.o. +381 11 20 70 684 Slovakia NA Datalan Service +421 2 49207155 Slovenia NA PC H.
6.Customer care and warranty Malaysia R-Logic Sdn Bhd +603 5102 3336 Mon.~Fri. 8:15am5:00pm Sat. 8:30am12:30am Pakistan TVONICS Pakistan +92-213-6030100 Sun.~Thu. 10:00am-6:00pm Singapore Philips Electronics Singapore Pte Ltd (Philips Consumer Care Center) (65) 6882 3966 Mon.~Fri. 9:00am-6:00pm Sat. 9:00am1:00pm Taiwan FETEC.CO 0800-231-099 Mon.~Fri. 09:00 18:00 Thailand Axis Computer System Co., Ltd. (662) 934-5498 Mon.~Fri.
7.Troubleshooting & FAQs 7. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. 7.1 Troubleshooting AUTO button doesn't function • This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. The auto function is applicable only in VGA-Analog mode.
7.Troubleshooting & FAQs Main Controls. It is valid only in VGA mode. image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Horizontal flicker appears Image appears distorted. Text is fuzzy or blurred. • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
7.Troubleshooting & FAQs Control Panel, select the 'Settings' tab. Under the setting tab, in box labelled 'desktop area', move the sidebar to 1920 x 1080 pixels. • Open 'Advanced Properties' and set the Refresh Rate to 60 Hz, then click OK. • Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1920 x 1080 @ 60 Hz. • Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor. • Turn on your monitor and then turn on your PC.
7.Troubleshooting & FAQs temperature yields "cool, bluewhite toning". period may cause "burn in", also known as "after-imaging" or "ghost imaging", on your screen. "Burn-in", "afterimaging", or "ghost imaging" is a well-known phenomenon in LCD panel technology. In most cases, the "burned in" or "atterimaging" or "ghost imaging" will disappear gradually over a period of time after the power has been switched off. Always activate a moving screen saver program when you leave your monitor unattended.
7.
© 2016 Koninklijke Philips N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license from Koninklijke Philips N.V. Specifications are subject to change without notice.
