Register your product and get support at www.philips.
Contents Clone data 25 Download software 25 4 2 Important 6 3 TV overview 9 Side controls 9 Guest menu 9 Access the guest menu with PBS setup remote control 9 Access the guest menu with guest remote control 10 4 Access and use the setup menu 11 Navigate the setup menu Select a language Select the country Set the type of communication Set the number of channels Auto install, program install, and configuration Cloning/upgrade and healthcare Set the clock 12 12 12 12 13 13
1 Notice 2009 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
1 2 3 Remove fuse cover and fuse. The replacement fuse must comply with BS 1362 and have the ASTA approval mark. If the fuse is lost, contact your dealer in order to verify the correct type. Refit the fuse cover. In order to maintain conformity to the EMC directive, the mains plug on this product must not be detached from the mains cord. Copyright Philips Consumer Lifestyle Philips Ltd.
2 Important • Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety • Risk of electric shock or fire! • Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
Risk of injury, fire or power cord damage! Never place the TV or any objects on the power cord. • To easily disconnect the TV power cord from the power outlet, ensure that you have full access to the power cord at all times. • When you disconnect the power cord, always pull the plug, never the cable. • Disconnect the TV from the power outlet and antenna before lightning storms. During lightning storms, never touch any part of the TV, power cord or antenna cable.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
Guest menu Eng lis h 3 TV overview This section gives you an overview of commonly used TV controls and functions and the Guest Menu. GUEST MENU FULLSCREEN ON ENGLISH ENGLISH OFF PICTURE FORMAT SUBTITLE SUBTITLE LANGUAGE AUDIO LANGUAGE SLEEPTIMER Side controls 4 3 MENU 2 Access the guest menu with PBS setup remote control 1 POWER RECALL TEXT a SMART SLEEP CC POWER : Switches the product on or off. The product is not powered off completely unless it is physically unplugged.
Access the guest menu with guest remote control MENU 1 2 10 Switch on the TV and select a TV channel. Press MENU to display the guest menu. » The guest menu is displayed.
Access the setup menu with PBS setup remote control POWER RECALL TEXT On-screen menus help you setup and install channels on the TV, change settings, and access different features. This section describes how to access the menus and configure the TVs. When the security level is [STANDARD], you can access the PBS setup menu with the PBS setup remote control or the guest remote control. When the security level is [HIGH], you must use the PBS setup remote control to access the PBS setup menu.
1 2 Switch on the TV and select a TV channel. Press ‘319753’ followed by (Mute) within 10 seconds. » The setup menu is displayed. Navigate the setup menu Set the type of communication You must set the correct communication protocol to work with an external system. 1 2 To navigate the setup menu, • Press on the remote control to select a menu. • Press to configure or modify the settings of the selected function.
Set the number of channels for different kinds of programs. The total number of channels for all programs is 250. 1 2 Enter the setup menu. Press Cloning/upgrade and healthcare Eng lis h Set the number of channels For detailed information on cloning/upgrade and healthcare, read the later sections of the user manual. to select [NO. OF PROGRAMS]. Set the clock NO. OF PROGRAMS TV PAYTV INFO RADIO STORE 235 4 3 15 > This section describes how to set the time and display the clock .
• • 14 EN [YES]. Set the download program as the startup program to achieve a fast startup time. [TIME OFFSET]: Sets the time offset. [BUZZER VOLUME]: Sets the volume of the alarm buzzer. Select [OFF] to switch off the buzzer.
This section describes how to configure the advanced settings for the TV, such as the switchon settings, picture and sound settings, energy saving, and control settings. 1 2 Enter the setup menu. Press to select [CONFIGURATION]. • • Configure the switch-on settings 1 2 CONFIGURATION SWITCH ON / OSD PICTURE SOUND SECURITY CONTROL ENERGY SAVING 3 Enter the setup menu. Press to select [CONFIGURATION] > [SWITCH ON / OSD].
• • • • • • [POWER ON]: Sets the power mode that is used when the TV is turned on after a prolong period of no activity (see ‘Preset the switch-on power mode’ on page 16). [VOLUME INDICATOR]: Sets the display of volume indicator (see ‘Enable or disable the volume indicator’ on page 17). [CHANNEL DISPLAY]: Sets the display of channel number and the label on the screen (see ‘Set the channel display’ on page 17).
3 Press to select [CONFIGURATION] > [SWITCH ON / OSD] > [POWER ON]. Press to select the power mode that is used when the TV is turned on from the AC mains power outlet: • [LAST STATUS]: Turns on the TV in the last used power mode. • [ON]: Turns on the TV. The button on the TV and the guest remote control are enabled. • [STANDBY]: Turns on the TV in standby mode. • [FORCED ON]: Turns on the TV. The button on the TV and the guest remote control are disabled.
• [DISPLAY ON STARTUP]: Displays ThemeTV on startup and when you press OK. • Configure the picture settings 1 2 3 • Enter the setup menu. Press to select [CONFIGURATION] > [PICTURE]. Press to select one of the following options: • [BRIGHTNESS]: Adjusts the light intensity or darkness. • [COLOUR]: Adjusts the color. • [CONTRAST]: Adjusts the contrast. • [SHARPNESS]: Adjusts the image sharpness. • [TINT]: Adjusts the color balance in an image.
• • • • PBS setup remote control’ on page 11). Enable or disable the TV controls 1 2 3 3 Enter the setup menu. Press to select [CONFIGURATION] > [SECURITY] > [SECURITY]. Press to select one of the following settings: • [STANDARD]: Accesses the setup menu using the PBS setup remote control or the guest remote control (see ‘Access the setup menu with guest remote control’ on page 11).
• • • [TUNER]: Sends the audio/ video output from the tuner to another TV that is connected to your TV. [MONITOR]: Sends the audio/ video output from a monitor to another TV that is connected to your TV. This is not available when input signal is protected with Vsecure, HDCP and Macrovision. [MUTE]: Disables the audio/ video output from all the sources. • • Configure the control options 1 2 • Enter the setup menu. • Press to select [CONFIGURATION] > [CONTROL].
3 • Insert RGB 1 2 3 Enter the setup menu. Press to select [CONFIGURATION] > [CONTROL] > [ALWAYS RGB]. Press to select one of the following options: • [AV1]: Allows RGB insertion in AV1 (EXT 1) and other sources. • [AUTO]: Allows RGB insertion in any source when [COMMUNICATION] in the setup menu is selected as [SP-SPI] or [SP-I2C]. Otherwise, allows RGB insertion in AV1 (EXT 1) only. • [NO RGB]: Prevents RGB insertion in any source. • [NO]: Allows RGB insertion in AV1 (EXT 1) only.
6 Automatically install the channels This section describes how to install the TV channels automatically. 1 2 Enter the setup menu. Press to select [AUTO INSTALL]. AUTO INSTALL DVB-C DVB-T ANALOG START 3 > > > > Press to select one of the following: • [DVB-C]: Installs DVB-C channels. The [FULL SCAN] searches all frequency spectrum and takes approximately 2 hours. Filling in [MODULATION] type and [SYMBOL RATE] will speed up auto installation.
3 This section describes how to install the TV channels manually. 1 2 1 2 3 Enter the setup menu. Press to select [PROGRAM INSTALL]. Press to manually install the channels. PROGRAM INSTALL PROGRAM NO. INPUT SYSTEM FREQUENCY STORE CHANNEL OPTIONS RINGS 4 Press TV 1 TUNER UK 123.4567> > > > 1 2 3 4 Enter the setup menu. Press to select [PROGRAM INSTALL] > [PROGRAM NO.]. Press to select the type of channel that you want to install: [TV], [PAYTV],[INFO], or [RADIO].
3 to select [STORE]. Press Note • [CHANNEL OPTIONS] is available only when you select [PROGRAM INSTALL] > [INPUT] > [TUNER]. 2 3 Label a channel 1 2 Enter the setup menu. Press to select [PROGRAM INSTALL] > [CHANNEL OPTIONS] > [LABEL]. CHANNEL OPTIONS LABEL FINE TUNE TELETEXT LANGUAGE MUTE PROTECTION (CNN_ _ _ _ _ ) > 0 UK NONE NO 4 1 2 4 4 5 6 Press to select a slot to enter a character. » A flashing red mark underlines the selected slot. Press to select a character.
1 This section describes how to clone the TV configuration data and download software. • 1 2 2 3 4 Enter the setup menu. Press to select [CLONING/ UPGRADE]. CLONING/UPGRADE CLONING SW DOWNLOAD RESET > > > • • Insert the USB storage device into the USB connector of your TV. Eng lis h 8 Clone data and upgrade software Enter the setup menu. Press to select [CLONING/ UPGRADE] > [CLONING]. Press to select one of the following options: [OPTIONS]: Selects the data to clone. • [ALL]: Clones all data.
3 • • • • • Press to set the source and type of the software download: [SOURCE]: Select [USB] or [RF] as the source of download. [SW TYPE]: Select one of the following types of software for download: • [SSB NVM]: Downloads SSB NVM software. • [SSB FIRMWARE]: Downloads digital software such as MPEG 2 and MPEG 4. • [8051 FIRMWARE]: Downloads the TV startup data. • [IBOARD NVM]: Downloads the TV settings. • [IBOARD FIRMWARE]: Downloads iboard software. • [ALL]: Downloads all the software upgrades.
This section describes how to select some of the features that are used in the healthcare industry. 1 2 • to a remote control of one of those colors. [REMOTE COLOUR]: Configures the TV to respond to the remote control of a particular color. Enter the setup menu. Press to select [HEALTHCARE].
10 Connect devices Back connectors VGA IN This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start. DATA 1 2 DATA 2 4 Note • Different types of connectors may be used to connect a device to your TV, depending on availability and your needs. A comprehensive interactive guide to help you connect your product is available at www.connectivityguide. philips.com. 1 3 5 12 11 SERV.
e HDMI 1/ HDMI 2 Digital audio and video input from highdefinition digital devices such as Blu-ray players. AUDIO OUT L/R Analog audio output to home theaters and other audio systems. SERV. U For Serial Express communication and use by service personnel. SPDIF OUT Digital audio output to home theaters and other digital audio systems. f EXT 3 (Y Pb Pr and AUDIO IN L/R ) Analog audio and component video input from analog or digital devices such as DVD players or game consoles.
Use a Conditional Access Module Access CAM services A Conditional Access Module (CAM) is provided by digital TV service operators to decode digital TV channels. 2 Note • If required, refer to documentation from your operator on how to insert a smart card into the Conditional Access Module. 1 After inserting and activating the CAM, enter the setup menu. Press to select [CONFIGURATION] > [SECURITY] > [CI CARD] > [YES]. » Applications provided by the digital TV service operator appear on the screen.
Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.
12 Troubleshooting This section describes commonly encountered issues and accompanying solutions. TV power on/ off issues The TV does not power on: • Ensure that the TV is connected to the AC mains power outlet. If it does not power on, pull the plug out of the power outlet, wait for 60 seconds, plug it back and turn the TV on again. The TV does not respond: • Check that the TV controls are not locked.
If the problem remains unresolved, contact Philips Consumer Care in your country as listed in the Addendum. Eng lis h • the digital ouput of the DVD player is set to PCM mode. Check that the [MIN VOLUME] is not set to zero (see ‘Configure the sound settings’ on page 18). Warning • Do not attempt to repair the product yourself. Communication issues The TV does not communicate with the external device: • Select the correct communication source.
13 Index E A Audio/video out Auto SCART 19 20 Energy saving ESP H C CAM Card slot Channel Channel banner Channel display Lock a channel Mute a channel Name a channel Rings of channels Scrambled channel Set the number of channels Switch-on channel Clock settings Buzzer volume Display clock Download time Set time Cloning Clone data from TV to USB Clone data from USB to TV Communication Conditional Access Module Configure settings Clock settings Control settings Energy saving Healthcare settings Pictur
S Screen care Security settings High security Keyboard lock RC lock Standard security Smart power Sound settings Switch-on settings Audio language Channel banner Channel display Power mode Subtitle language Switch-on channel Switch-on picture format Switch-on power Switch-on volume TV theme Volume indicator Welcome message T Troubleshooting 11 27 11 19 27 21 24 Eng lis h Guest RC Multi RC PBS setup RC RC lock Remote control color RGB insertion Rings of channels 7 19 19 19 19 21 18 17 17 17 16 17 16 1
38
© 2008 Koninklijke Philips Electronics N.V. All rights reserved.
