Philips Professional and Business Solutions User Manual 26HF7875 26HF5445 32HF7875 32HF5445 42HF7845
Contents Contents ................................................ 1 Installing a System SmartCard or System Box ......................................... 35 Introduction .......................................... 2 Diagnosing Basic Problems ............... 37 Kensington Security Slot ..................... 2 Safety ..................................................... 3 Appendix A – Multi Remote Controls Support ............................................... 39 Troubleshooting .........................
Introduction Congratulations on your purchase and welcome to Philips! This manual contains information about how to install and operate your TV. If you still have problems after reading this manual, call your Local Philips Customer or Service Centre. The telephone numbers and addresses are given in the worldwide guarantee booklet supplied with the TV.
Safety 1. Two people are required to lift and carry a TV that weighs more than 25 kilograms. Improper handling of the TV can cause serious injury. 2. If you place the TV set on a solid surface, ensure the surface is level and that it can withstand the weight of the TV. 3. Mounting the TV on the wall requires special skill that should only be performed by a qualified personnel. You should not attempt to do the work yourself.
Troubleshooting If you are experiencing problems, check this list of symptoms and suggested steps to take before requesting service. You may be able to solve the problem yourself. Note: Please be familiar with the commercial features as described in the TV installation. The effects of several of these features if not thoroughly understood might appear as faulty operation.
Troubleshooting Symptoms Power Possible Solutions TV cannot be • If you are using the POWER button of the remote control to switched on switch on the TV, note that button is only use to set the TV to stand-by mode. Use the Digit 0-9 or CH + / – buttons to switch on TV. • Check if YES is selected in the REMOTE CONTROL LOCK feature in SECURITY menu. Select NO to deactivate lock function (see page 23). • Check if ALL is selected in the KEYBOARD LOCK feature in SECURITY menu.
Getting started Mounting the TV on a wall How to switch your TV on This TV is compatible with the VESA wall mounting standard. Please contact your local electronics retailer for a VESA compliant bracket to wall mount this TV. To switch the TV on, press the POWER key on the side controls. A green indicator light comes on and after a few seconds the screen lights up. Insert the cables into the TV before you mount it on the wall. If the TV set remains in stand-by mode, the indicator light remains red.
Overview of TV Connectors and Controls 9 DATA 1 DATA 2 4 8 VGA In 3 15 PROGRAM 10 2 1 EXT 4 EXT 3 11 12 13 Warning Do not connect any telephone cables or equipment to Data 1 (RJ12) & Data 2 (RJ45) connectors. 1. . POWER To switch off the TV. 2. - PROGRAM + To switch on TV and also to select the next or previous programme. 3. MENU To display or close menus. 4. - VOLUME + To increase or decrease volume. 5. Data 1 (RJ 12) For System Terminal connection. 6.
Remote Controls The following remote controls are applicable to Philips Professional and Business Solutions TV products. These can be used for setup and configuration purposes. RC2573 is an optional remote control for Institutional TV / Professional and Business Solutions features and SmartCard settings. It can be purchased separately. RC2886 POWER Guest Mode Remote Control RECALL TEXT SMART SLEEP CC Slide this button up to enter into Guest mode. or Slide this button down to enter into Setup mode.
Guest Remote Control Keys 1. Alarm On To activate the alarm function. Applicable to models with the clock display. 1 2 3 4 5 6 7 8 9 2. Alarm Off To deactivate the alarm function. Applicable to models with the clock display. 3. Smart Sound To select the predefined sound settings. 4. Sleep To activate the sleep timer. Press the button repeatedly to increase countdown time. 5. Menu To call up or exit the menus when a System Box or System SmartCard is installed.
Guest Remote Control Keys 10 11 12 13 14 15 16 17 10. Power To set the TV to stand-by mode. 11. PAY TV / INFO / RADIO To access the first available Pay TV, Info or Radio channel. The + and – buttons allow you to access the next and previous programme. 12. Smart Picture To select predefined picture settings. 13. OK To confirm a selection. 14. TV + / – To switch on TV. To select the next or previous programme. 15. Mute To turn off or on sound. 16. 0 to 9 Digit keys To switch on TV. To select a TV channel.
Overview of TV Setup Main Menu / Sub-Menus SETUP LANGUAGE COMMUNICATION COMMUNICATION STORE DCM TYPE NO. OF PROGRAMS TV PAY TV INFO RADIO STORE PROGRAM INSTALL PROGRAM NO. INPUT SYSTEM FREQUENCY LABEL STORE FINE TUNE MUTE TELETEXT LANGUAGE PROTECTION ENGLISH, FRANCAIS, DEUTSCH, ITALIANO SP - SPI, SP - I2C, HM -LINK, SERIAL XPRESS, MULTI RC, SMART RC, OFF > GENERIC, NO SOURCE SWITCH 35 5 5 5 > TV 1, INFO 1, PAYTV, RADIO TUNER, AV1, AV2, SVIDEO, EXT3 CVBS, EXT3 SVIDEO, EXT4 CVI.
Overview of TV Setup Main Menu / Sub-Menus SETUP CONFIGURATION SWITCH ON / OSD PICTURE / SOUND SECURITY CONTROL VIDEO ADJUSTMENT FEATURES > > > > > > * CLOCK SETUP DISPLAY STANDBY DISPLAY ON TIME SETTING TELETEXT TIME DOWNLOAD DOWNLOAD PROGRAM TIME OFFSET BUZZER VOLUME > > > > > > > * CLOCK SETUP function is avaliable for certain models only.
Accessing the Setup Menu The following remote control commands are applicable to Philips Professional and Business Solutions products. These can be used for setup and configuration purposes. Accessing TV Setup Menu using the Remote Control (RC2573) 1. Slide the button to the SETUP location. Accessing TV Setup Menu using the Remote Control (RC2886) POWER RECALL TEXT 1. Press the Digit 0 -9 buttons to select a channel.
Installation A. Selecting the language COMMUNICATION COMMUNICATION STORE ENABLE CARD SLOT DCM TYPE You can select ENGLISH, FRANCAIS, DEUTSCH or ITALIANO as your preferred language. • OFF > YES GENERIC In the SETUP menu, press the > button repeatedly to select your preferred language. SETUP LANGUAGE COMMUNICATION NO.
Installation Note: The total number of programmes you can define for TV, PAYTV, INFO and RADIO is 125. For example, if you define 50 programmes for TV, 30 for PAYTV and 20 for INFO, the number of programmes available for RADIO is 25. The total number of programmes allowed is 125. C. Defining the number of available channels This feature allows you to define the number of available channels for TV, Pay TV, Info (Info Channel) and Radio. • In the SETUP menu, press the > button to highlight NO.
Installation 2. Selecting an input source PROGRAM INSTALL PROGRAM NO. INPUT SYSTEM FREQUENCY LABEL STORE FINE TUNE MUTE TELETEXT LANGUAGE PROTECTION TV 1 TUNER WEST EU 559.2500 > ( )> > 0 NONE WEST EU NO • Press the < or > button to select the item you want to configure. • Press the < or > button to make adjustment or select option. 1. Selecting a programme number • Press the > button repeatedly to select the desired type of program TV, PAYTV, INFO (Info Channel) or RADIO.
Installation 3. Selecting the TV system Note: You can only select SYSTEM if TUNER is selected in the INPUT source. • Press the > button to select SYSTEM and press the > button repeatedly to select the desired system (WEST EU, UK, EAST EU or FRANCE). PROGRAM INSTALL PROGRAM NO. INPUT SYSTEM FREQUENCY LABEL STORE FINE TUNE MUTE TELETEXT LANGUAGE PROTECTION TV 1 TUNER WEST EU 559.2500 > ( )> > 0 NONE WEST EU NO PROGRAM INSTALL PROGRAM NO.
Installation • Press the > button to move to the next character slot and continue to select the next character with the < or > button (maximum of 8 characters). • Press the mode. button to exit label • Press the > button to select STORE. • Press the > button to store name. The name will appear on the top left hand corner of the TV screen when you switch to the channel which have been assigned a name. 7. Muting the Audio or Video source You can choose to mute the Audio or the Video source.
Installation • Press the > button to select YES. PROGRAM INSTALL PROGRAM NO. INPUT SYSTEM FREQUENCY LABEL STORE FINE TUNE MUTE TELETEXT LANGUAGE PROTECTION TV 1 TUNER WEST EU 559.2500 > (SPORTS )> > 2 NONE WEST EU NO PROGRAM INSTALL PROGRAM NO. INPUT SYSTEM FREQUENCY LABEL STORE FINE TUNE MUTE TELETEXT LANGUAGE PROTECTION TV 1 TUNER WEST EU 559.2500 > (SPORTS )> > 2 NONE WEST EU YES • Press the < button repeatedly until STORE is highlighted. • Press the < button repeatedly until STORE is highlighted.
Installation * VIDEO ADJUSTMENT feature is only available when the input source selected is EXT4 CVI, VGA, HDMI 1 or HDMI 2. • Press the > button to enter SWITCH ON / OSD menu. SWITCH ON / OSD WELCOME MESSAGE SWITCH ON PROGRAM SWITCH ON VOLUME SWITCH ON PIC FMT POWER ON VOLUME INDICATOR PROGRAM DISPLAY • Press the > button to enter CONFIGURATION menu.
Installation If LAST STATUS option is selected, the last power status will be activated when TV is switched on. If ON option is selected, the TV will always switch on when the mains cord is inserted in the mains socket and turn on. The POWER buttons on the Guest Remote Control and the TV will be enabled. If STANDBY option is selected, the TV will switch on to stand-by mode whenever the main power is switched on.
Installation The SECURITY feature allows you to select and configure the settings and options for : The SECURITY feature offers you two security modes: STANDARD and HIGH. – – – – • Press the < or > button to select STANDARD or HIGH. SECURITY KEYBOARD LOCK REMOTE CONTROL LOCK VIDEO OUT MUTE If STANDARD option is selected, the TV SETUP menu can be accessed by entering a special security code with a guest remote control. • Press the > button and select SECURITY.
Installation • Press the > button to select YES to lock the TV keyboard buttons except for the POWER button. The VIDEO OUT MUTE feature allows you to mute the Video from the TV to any external devices. • Select ALL to lock all the TV keyboard buttons including the POWER button. • Press the > button to select VIDEO OUT MUTE. • Select NO to unlock all the TV keyboard buttons including the POWER button. The REMOTE CONTROL LOCK feature allows you to lock all the guest remote control buttons.
Installation CONFIGURATION SWITCH ON / OSD PICTURE / SOUND SECURITY CONTROL VIDEO ADJUSTMENT FEATURES > > > > > > Note : If a remote or keyboard command is received before the ESP time period expires, the Timer will reset and begin counting down again. • Press the < or > button to select a specified time period. CONTROL • Press the > button to enter the CONTROL menu. CONTROL ESP AUDIO / VIDEO MUTE STEP TUNING DIGIT TIMEOUT AUTO SCART ALWAYS RGB MIN VOLUME MAX VOLUME OFF NO NO 3.
Installation The STEP TUNING feature allows tuning to be performed for each digit entry if YES is selected. • Press the > button to select STEP TUNING. CONTROL ESP AUDIO / VIDEO MUTE STEP TUNING DIGIT TIMEOUT AUTO SCART ALWAYS RGB MIN VOLUME MAX VOLUME 2 YES YES 3.0 NO NO 0 99 CONTROL ESP AUDIO / VIDEO MUTE STEP TUNING DIGIT TIMEOUT AUTO SCART ALWAYS RGB MIN VOLUME MAX VOLUME 2 YES YES 3.0 NO NO 0 99 • Press the > button to select YES to activate STEP TUNING function.
Installation If ALL is selected, the TV will then react to both AV1 and AV2. If POWER SCART is selected, the TV when in stand-by mode will automatically switch on when a scart signal is detected. Likewise, when a scart signal is not detected, the TV will go to stand-by automatically. CONTROL ESP AUDIO / VIDEO MUTE STEP TUNING DIGIT TIMEOUT AUTO SCART ALWAYS RGB MIN VOLUME MAX VOLUME 2 YES YES 3.0 POWER SCART NO 0 99 The ALWAYS RGB feature controls RGB insertion in TV auxiliary sources.
Installation • If COMMUNICATION is not SP-SPI or SP-I2C, select AUTO to allow RGB insertion in AV1 (EXT1) and not other sources. The MIN and MAX VOLUME options allow you to specify the limit setting for Minimum and Maximum Volume. • Press the > button repeatedly to select MIN VOLUME or MAX VOLUME. * Functions available only when the input sources selected are VGA, EXT4 CVI and CARD EXT4. Note: VIDEO ADJUSTMENT feature is only available when the input source is in EXT4 CVI, VGA, HDMI 1 or HDMI 2.
Installation Note: HORIZONTAL and VERTICAL options are only available when the input sources selected are HDMI 1 or HDMI 2. • Press the < or > button to select HORIZONTAL or VERTICAL. VIDEO ADJUSTMENT HORIZONTAL VERTICAL PHASE CLOCK AUTO ADJUST RESET < < < < > > > > > > VIDEO ADJUSTMENT HORIZONTAL VERTICAL PHASE CLOCK AUTO ADJUST RESET < < < < > > > > > > • Press the < or > button to adjust the picture horizontally or vertically.
Installation The RESET option allows you to return to the factory settings (default settings). Note: RESET is only available when the input sources selected are VGA, EXT4 CVI and CARD EXT4. CONFIGURATION SWITCH ON / OSD PICTURE / SOUND SECURITY CONTROL VIDEO ADJUSTMENT FEATURES > > > > > > • Press the > button to select RESET. VIDEO ADJUSTMENT HORIZONTAL VERTICAL PHASE CLOCK AUTO ADJUST RESET < < < < > > > > > > • Press the > button to enter the FEATURES menu.
Installation FEATURES SMART POWER SMART SOUND KEY DEFAULT HDMI 1 AUDIO DEFAULT HDMI 2 AUDIO LOW POWER STANDBY FEATURES LOW SMART SOUND EXT3 AUDIO HDMI NO The SMART SOUND KEY option allows you to select between AUDIO SELECT or SMART SOUND. • Press the > button to select SMART SOUND KEY.
Installation The LOW POWER STANDBY option allows you to save electricity when TV is in stand-by mode. • Press the > button repeatedly until LOW POWER STANDBY is highlighted. FEATURES SMART POWER SMART SOUND KEY DEFAULT HDMI 1 AUDIO DEFAULT HDMI 2 AUDIO LOW POWER STANDBY LOW SMART SOUND EXT3 AUDIO HDMI NO • Press the > button to select YES to activate LOWER POWER STANDBY option. 7. BUZZER VOLUME Note : CLOCK SETUP feature is applicable for certain models only.
Installation • Press the < or > button to set the brightness level (1 - 5 and OFF). • CLOCK SETUP DISPLAY STANDBY DISPLAY ON TIME SETTING TELETEXT TIME DOWNLOAD DOWNLOAD PROGRAM TIME OFFSET BUZZER VOLUME CLOCK SETUP 3 > > > > > > 2. Setting the brightness level of the clock when the TV is switched on You can also set the brightness level of the clock display when the TV is switched on. • Press the > button to select DISPLAY ON.
Installation 5. Retrieving the correct time from Teletext of the selected channel • You can select a channel which has teletext transmission from which the correct time from the teletext is retrieved. • Press the < or > button to select TIME OFFSET. CLOCK SETUP DISPLAY STANDBY DISPLAY ON TIME SETTING TELETEXT TIME DOWNLOAD DOWNLOAD PROGRAM TIME OFFSET BUZZER VOLUME Press the < or > button to select DOWNLOAD PROGRAM.
Cloning the TV and the SmartLoader configuration Cloning the TV configuration to the SmartLoader Cloning the SmartLoader configuration to the TV • • Slide button on the left of the SmartLoader up to the position. Aim SmartLoader at green LED of the TV (5 to 15 cm away). Slide button on the left of the Smart Loader up to the position. Aim SmartLoader at green LED of the TV (5 to 15 cm away).
Installing a System SmartCard or System Box NOTE: Before installing a System SmartCard or System Box, ensure the TV is switched off. Sample of System Box 1. Inserting the System SmartCard or System Box • • Insert the SmartCard into the SmartCard slot on the rear of the TV (available for certain models only) and connect the other cables as directed by the System provider. After the SmartCard has been inserted and the cables connected, switch on the TV.
Installing a System SmartCard or System Box 3. Enabling the Card Slot FEATURES For the System SmartCard or System Box to function, the Card Slot must be enabled. • SMART POWER SMART SOUND KEY DEFAULT HDMI 1 AUDIO DEFAULT HDMI 2 AUDIO LOW POWER STANDBY Press the > button to select ENABLE CARD SLOT. COMMUNICATION COMMUNICATION STORE ENABLE CARD SLOT DCM TYPE SP - 12C > YES GENERIC • LOW SMART SOUND EXT3 AUDIO HDMI NO Press the > button to select NO. 5.
Diagnosing Basic Problems 1. TV does not seem to communicate with the external interactive terminal. – COMMUNICATION COMMUNICATION STORE ENABLE CARD SLOT DCM TYPE Check the Communication Source • Press the RECALL button on the remote (in Setup position). Item 08 of the menu should read COMMUNICATION SP - I2C ONLINE. 01 26HF7875 / 10 02 SV1A0707100003 03 IC7E1 - 0 . 18 04 LC71HEL1 - 0 .
Diagnosing Basic Problems – Check whether the Card Slot is enabled • If the TV still does not communicate with the System SmartCard, in the COMMUNICATION menu, press the > button repeatedly until ENABLE CARD SLOT is highlighted. COMMUNICATION COMMUNICATION STORE ENABLE CARD SLOT DCM TYPE OFF > YES GENERIC FEATURES SMART POWER SMART SOUND KEY DEFAULT HDMI 1 AUDIO DEFAULT HDMI 2 AUDIO LOW POWER STANDBY LOW SMART SOUND EXT3 AUDIO HDMI NO • Press > button and select LOW POWER STANDBY. 2.
Appendix A – Multi Remote Controls Support Programming the Multi Remote Controls function Multi RC function supports up to four TV sets operating in one room without any interference from each other remote controls. Each Guest Remote Control must be programmed individually to one of the four colour (Blue, Yellow, Green and Red) buttons on the remote control. button on the GREEN 1. Press the remote control to activate the TV SETUP Menu. 2. Press the > button to select COMMUNICATION.
Appendix B – Resolutions Table Refer to the HDMI INPUT table if you use the HDMI connector to plug in a PC (PC Format) or a Video Input (Video Format), for example, a HDMI DVD player.
Environmental Information Recycling The packaging of this product is intended to be recycled. Contact your local authorities for information about how to recycle the packaging. Note: Specifications and information are subject to change without notice. For further assistance, call the customer support service in your country. The telephone numbers and addresses are given in the worldwide guarantee booklet supplied with the TV.
Information for Users in the UK (Not applicable outside UK) Important Positioning the TV For the best results, choose a position where light does not fall directly on the screen, and at some distance away from radiators or other sources of heat. Leave a space of at least 5 cm all around the TV for ventilation, making sure that curtains, cupboards etc. cannot obstruct the air flow through the ventilation apertures.
© 2007 Koninklijke Philips N.V.
