243S7 www.philips.
Table of Contents 1. Important ....................................... 1 1.1 Safety precautions and maintenance .................................. 1 1.2 Notational Descriptions ............. 3 1.3 Disposal of product and packing material........................................... 4 2. Setting up the monitor ............... 5 2.1 Installation ..................................... 5 2.2 Operating the monitor................ 6 2.3 Remove the Base Assembly for VESA Mounting ........................... 8 3.
1. Important proper cooling of the monitor’s electronics. 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user's manual before you use your monitor. It contains important information and notes regarding the operation of your monitor.
1. Important • Reposition your screen to appropriate height and angle according to your height. • Adjusting the brightness and contrast to appropriate level. • Adjusting the environment lighting similar to that of your screen brightness, avoid the fluorescent lighting, and surfaces that don’t reflect too much light. • Seeing a doctor if your symptoms. eign substance or water, and send it to the maintenance center.
1. Important • If there is any need for any document for repair or integration, please contact with your local service center. (Please refer to Service contact information listed in Important information manual.) • For transportation information, please refer to “Technical Specifications”. • Do not leave your monitor in a car/ trunk under direct sun light. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document.
2. Setting up the monitor Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install base stand 2. Setting up the monitor 1. 2.1 Installation Package contents Place the monitor face down on soft and smooth surface taking care to avoid scratching or damaging the screen. 2. Attach/Slide the base column with the monitor until it clicks into position. Register your product and get support at www.philips.com/welcome 243S7 Power 3. Hold the monitor base stand with both hands and firmly insert the base stand into the base column.
2. Setting up the monitor Connecting to your PC 2.2 Operating the monitor Front view product description 4 5 4 6 5 AC power input VGA input DVI-D input HDMI input HDMI audio out Kensington anti-theft lock 3 7 5 4 2 Switch monitor’s power ON and OFF. Connect to PC 1. 6 Access the OSD menu. Confirm the OSD adjustment. Connect the power cord to the back of the monitor firmly. 2. Turn off your computer and unplug its power cable. Adjust the OSD menu. 3.
2. Setting up the monitor Description of the On Screen Display Main menu LowBlue Mode What is On-Screen Display (OSD)? On 1, 2, 3 Off On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor Resolution notification 2.3 Remove the Base Assembly for VESA Mounting This monitor is designed for optimal performance at its native resolution, 1920 × 1080 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best results. Remove the Base Stand Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 100mm 100mm 0° 90° -5° * Display design may differ from those illustrated. Warning • To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than -5 degrees. • Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
3. Image Optimization 3. Image Optimization 1. 3.1 SmartImage 2. Keep pressing to toggle among EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode and Off. What is it? SmartImage provides presets that optimize display for different types of content, dynamically adjusting brightness, contrast, color and sharpness in real time. Whether you're working with text applications, displaying images or watching a video, Philips SmartImage delivers great optimized monitor performance.
3. Image Optimization sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors all without artifacts and faded colors. • Movie: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every details in darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the ultimate video display.
4. Technical Specifications 4. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch SmartContrast Optimum Resolution Viewing Angle (typ.) Picture Enhancement Display Colors Vertical Refresh Rate Horizontal Frequency sRGB Flicker Free LowBlue Mode Connectivity Signal Input Input Signal Audio out Convenience User Convenience OSD Languages Other Convenience Plug & Play Compatibility Stand Tilt IPS Technology W-LED system 23.8" W (60.5 cm) 16:9 0.275 x 0.
4. Technical Specifications Normal Operation Sleep (Standby mode) Off mode Power LED indicator Power Supply 72.66 BTU/hr(typ.) 73.00 BTU/hr(typ.) 73.34 BTU/hr(typ.) <1.71 BTU/hr <1.71 BTU/hr <1.71 BTU/hr <1.71 BTU/hr <1.71 BTU/hr <1.
4. Technical Specifications 4.1 Resolution & Preset Modes Maximum Resolution 1920x1080@60Hz (analog input) 1920x1080@60Hz (digital input) Recommended Resolution 1920x1080@60Hz (analog input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 35.16 800 x 600 56.25 37.88 800 x 600 60.32 48.08 800 x 600 72.19 46.88 800 x 600 75.00 47.73 832 x 624 74.55 48.36 1024 x 768 60.00 56.
5. Power Management 5. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
6. Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 6. Customer care and warranty 6.
6. Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
6. Customer care and warranty TOTAL DOT DEFECTS Total bright or black dot defects of all types 1.
6. Customer care and warranty 6.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For Warranty Period please refer to Warranty Statement in Important Information Manual. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center.
7. Troubleshooting & FAQs 7. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. AUTO button doesn't function 7.1 Troubleshooting • This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. The auto function is applicable only in VGA-Analog mode.
7. Troubleshooting & FAQs Main Controls. It is valid only in VGA mode. Image appears distorted. Text is fuzzy or blurred. Horizontal flicker appears • • Adjust the image using the “Auto” function in OSD Main Controls. Green, red, blue, dark, and white dots appears on the screen • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode. • • You can adjust “power on” light using the power LED Setup in OSD main Controls.
7. Troubleshooting & FAQs • Restart your computer and repeat step 2 and 3 to verify that your PC is set at 1920 x 1080 @ 60 Hz. • Shut down your computer, disconnect your old monitor and reconnect your Philips LCD monitor. • Turn on your monitor and then turn on your PC. blunt objects. When handling the monitor, make sure that there is no pressure or force applied to the panel surface side. This may affect your warranty conditions. Q7: How should I clean the LCD surface? Ans.
7. Troubleshooting & FAQs Kelvin). Lower Kevin temperatures such as 2004K are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K. Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. Q9: Can I connect my LCD monitor to any PC, workstation or Mac? Ans.
© 2017 Koninklijke Philips N.V. All rights reserved. This product was manufactured and brought to the market by or on behalf of Top Victory Investments Ltd. or one of its affiliates. Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. used under license. Specifications are subject to change without notice.
