Brilliance 241B7 www.philips.
Table of Contents 1. Important �����������������������������������������������1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the monitor �����������������������5 2.1 Installation ������������������������������������ 5 2.2 Operating the monitor �������������� 6 2.
1. Important discoloration and damage to the monitor. 1. Important This electronic user’s guide is intended for anyone who uses the Philips monitor. Take time to read this user manual before you use your monitor. It contains important information and notes regarding operating your monitor. • Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics. • Do not block the ventilation holes on the cabinet.
1. Important minute break after 50-60-minute continuous screen use is likely to be better than a 15-minute break every two hours. Try to keep your eyes from eye strain while using the screen for a constant period of time by : • To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. • If your monitor gets wet, wipe it with dry cloth as soon as possible.
1. Important Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. 2.1 Installation Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. Package contents Brilliance 241B7 278E9 Quick Start 2. Hold the stand with both hands. (1) Gently attach the stand to the VESA mount area until the latch locks the stand. Register your product and get support at www.philips.
2. Setting up the monitor 2.2 Operating the monitor Connecting to your PC Description of the control buttons 9 8 7 6 5 4 3 2 1 3 7 9 5 4 6 1 Kensington anti-theft lock 2 USB downstream 3 3 USB upstream 4 Earphone jack 5 MIC 7 6 6 Ethernet 7 VGA input 4 2 1 Switch monitor’s power ON and OFF. 8 Power Switch 9 AC power input Access the OSD menu. Confirm the OSD adjustment. Connect to PC 1. 5 Adjust the OSD menu. Connect the power cord to the back of the monitor firmly.
2. Setting up the monitor Description of the On Screen Display The OSD Menu Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor Height adjustment Resolution notification This monitor is designed for optimal performance at its native resolution, 1920 × 1080 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best results. Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. 100mm 100mm 2. Place the monitor face down on a smooth surface.
3. Image Optimization 3. Image Optimization 1. 3.1 SmartImage 2. Keep pressing to toggle among Office, Photo, Movie, Game, Economy, LowBlue Mode and Off. What is it? Press to launch the SmartImage on screen display. 3. The SmartImage on screen display will remain on screen for 5 seconds, or you can also press "OK" to make confirmation. SmartImage. There are multiple selections: Office, Photo, Movie, Game, Economy, LowBlue Mode and Off.
3. Image Optimization color washout in brighter areas maintaining a dynamic natural values for the ultimate video display. • Game: Turn on over drive circuit for best response time, reduce jaggy edges for fast moving objects on screen, enhance contrast ratio for bright and dark scheme, this profile delivers the best gaming experience for gamers.
4. PowerSensor™ 4. PowerSensor™ • • • • How does it work? PowerSensor works on principle of transmission and reception of harmless “infrared” signals in order to detect user-presence. When the user is in front of the monitor, the monitor operates normally, at the predetermined settings that the user has set- i.e.
4. PowerSensor™ returned to its default Landscape position. Note A manually selected PowerSensor mode will remain operational unless and until it is readjusted or the default mode is recalled. If you find that the PowerSensor is excessively sensitive to nearby motion for some reason, please adjust to a lower signal strength. Keep sensor lens clean, if the sensor lens is dirty, wipe it with alcohol to avoid reducing of distance detection .
5.USB docking display Introduction 5.1 How to operate USB docking display 5. USB docking display Introduction DisplayLink Graphics Software Installation If you are among the majority of the Notebook users who do not have the convenience of a docking station, then this USB docking display is your best choice. In order to use your USB docking display, DisplayLink Graphic software is required to be installed in your windows system. This software allows you to easily control your display preferences.
5.USB docking display Introduction 6. You will be able to see pictures on the USB docking display after Windows completes boot up process. 2. Click Yes, then software start to install DisplayLink Core software and DisplayLink Graphics installs. Controlling the display When devices are attached, an icon appears in the taskbar. This gives you access to the DisplayLink manager menu. To use the DisplayLink Manager Menu Note 1.
5.USB docking display Introduction Menu Option Sub-menu Option Description DisplayLink Manager DisplayLink devices This is the UI title. Clicking on this item will open Windows screen resolution. Options to configure Philips 241B7QU device In this section of the menu, a list of connected DisplayLink devices will appear. Each of these devices has its own subconfiguration menu. These Submenu options are covered in the table below.
5.USB docking display Introduction Menu Option Sub-menu Option Description Notebook Display Off Switches off the display of the notebook and makes the DisplayLink display the main display. Note: This option will only appear when 1 DisplayLink USB screen, is connected. It will also only appear on Laptop computers. Mirror Copies what is on the main display and reproduces it on this display. Note: The resolution of this display and the primary must be the same in mirror mode.
5.USB docking display Introduction Setting USB docking Ethernet 3. Right click on the Realtek USB GBE Family Controller icon and click “Enable”, now you can surf the internet. 1. Open “Network Connections” window On Windows 10, Windows 8 or Windows 7, type “ncpa.cpl” into the Start menu search box: 2. The Network Connections window opens. Locate and select the “Realtek USB GBE Family Controller“ for preferred network source.
5.USB docking display Introduction USB docking station 2. Right click on 2 - USB Audio Device, then click Enable Built-in earphone jack, mic in, speakers, ethernet, 1x3.0 USB upstream and 3x3.0 USB downstream makes this display a convenient and time-saving work station using only one single USB cable to connect USB 3.0 upstream/ downstream ports between display and laptop. 3.
6.Technical Specifications 6. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio (typ.) Optimum Resolution Viewing Angle Display Colors Flicker Free Picture Enhancement Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode Connectivity IPS Technology LED 23.8" W (60.5 cm) 16:9 0.275(H) mm x 0.275(V) mm 1000:1 1920 x 1080 @ 60 Hz 178° (H) / 178° (V) @ C/R > 10 16.
6.
6.Technical Specifications Environmental and energy ROHS Packaging Specific Substances Cabinet Color Finish YES 100% recyclable 100% PVC BFR free housing Black Texture Note 1. This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet. 2. USB hub is only support mouse or keyboard to wake up the system while on power saving mode.
6.Technical Specifications 6.1 Resolution & Preset Modes Maximum Resolution 1920 x 1080 @ 60 Hz (analog input) 1920 x 1080 @ 60 Hz (digital input) Recommended Resolution 1920 x 1080 @ 60 Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 35.16 800 x 600 56.25 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.08 800 x 600 72.19 47.73 832 x 624 74.55 48.
7.Power Management 7. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
8.Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 8. Customer care and warranty 8.
8.Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
8.Customer care and warranty Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
8.Customer care and warranty 8.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center. For Warranty Period please refer to Warranty Statement in Important Information Manual.
9.Troubleshooting & FAQs 9. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. 9.1 Troubleshooting AUTO button doesn't function • This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. The auto function is applicable only in VGA-Analog mode.
9.Troubleshooting & FAQs Main Controls. It is valid only in VGA mode. and cannot be repaired. The damage mentioned above is not covered under your warranty. Horizontal flicker appears Image appears distorted. Text is fuzzy or blurred. • • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
9.Troubleshooting & FAQs you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the companion CD-ROM included in this package. Monitor drivers (.inf and .icm files) will be installed automatically. 9.2 General FAQs Q1: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? Ans.: Recommended resolution for this monitor: 1920 x 1080 @ 60 Hz.
9.Troubleshooting & FAQs Ans.: Yes, you can change your color setting through OSD control as the following procedures, Mac system. Please contact your Philips sales representative for more information. • Press "OK" to show the OSD (On Screen Display) menu Q10: Are Philips LCD monitors Plugand- Play? • Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below. 1.
9.Troubleshooting & FAQs 9.3 USB docking display FAQs Ans.: Your LCD monitor works best at its native resolution of 1920 x 1080 @ 60 Hz. For best display, please use this resolution. Q1. Q13: How to unlock/lock my hot key? Unable to access my internet connection after connecting 241B7QU to my notebook or desktop. Ans.: Be sure you are using the latest drive for your notebook or desktop. Otherwise, you may need to update your USB Ethernet driver, which can be done through our user manual or www.
9.Troubleshooting & FAQs Ans.: The issue can be resolved when switching off the audio in your notebook or desktop. Q4. How can I rotate my screen when I rotate my display? Ans.: You would need to use the OSD/ OSD setting/OSD Rotate to rotate your screen.
2019 © TOP Victory Investment Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
