e-Manual Philips LCD Monitor Electronic User’s Manual file:///D|/My%20Documents/dfu/230WP7/english/230wp7/index.
Safety and Troubleshooting Information • Safety Precautions and Maintenance • FAQs Safety and Troubleshooting Information Safety precautions and maintenance • Troubleshooting WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Safety and Troubleshooting Information Maintenance: ● ● ● ● ● ● ● ● To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD panel. Unplug the monitor if you are not going to use it for an extensive period of time. Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off.
About This Manual • About This Guide • Notational Descriptions About This Manual About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other important information. Its contents are identical to the information in our printed version.
About This Manual NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may not be accompanied by an icon.
Product Information • Product Features Product Information • Technical Specifications • Resolution & Preset Modes Product Features • Philips Pixel Defect Policy 230WP7NS • Automatic Power Saving ● Designed for maximum productivity • Physical ❍ Big, widescreen ideal for viewing two A4 pages side-by-side Specification ❍ 90 degree screen rotation and smart cable management • Pin ❍ Designed for 'just-right' height and angle adjustment Assignment ● Best total cost of ownership solution • Product ❍ SmartManage c
Product Information Horizontal Frequency 30kHz-94kHz (Analog input) VIDEO • Video dot rate 205 MHz • Input impedance - Video 75 ohm - Sync 2K2 ohm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polarities Positive and negative Optical characteristics • Peak contrast angle 6 o'clock • White Chromaticity: x: 0.283 y: 0.297 (at 9300°K) x: 0.313 y: 0.329 (at 6500°K) * This data is subject to change without notice.
Product Information 49.7 832*624 75 48.4 1024*768 60 60 1024*768 75 68.7 1152*870 75 71.8 1152*900 76 64 1280*1024 60 80 1280*1024 75 91.1 1280*1024 85 75 1600*1200 60 67.1 1920*1080 60 74.6 1920*1200 60 75.0 1600*1200 60 RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use.
Product Information • Power consumption 80 W* (typ.) • Temperature 5° C to 35° C (operating) -20° C to 60° C (storage) • Relative humidity 20% to 80% • System MTBF 50K hrs (excluding CCFL 40K hrs) • Cabinet color Black/Silver • Altitude - storage/shipment - operating 0 - 40,000 feet (12,192m) 0 - 12,000 feet (3657.6m) * This data is subject to change without notice. * Resolution 1920 x 1200, standard size, contrast max., brightness 50%, 6500° K, full white pattern.
Product Information Pin Assignment No. Pin Assignment No. 1 Red video input 9 +5V 2 Green video input/SOG 10 Ground 3 Blue video input 11 Ground 4 Ground 12 Serial data line (SDA) 5 Cable detect 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC) 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components.
Product Information 1) Tilt 2) Swivel file:///D|/My%20Documents/dfu/230WP7/english/230wp7/product/product.
Product Information 3) Height adjustment 4) Portrait display file:///D|/My%20Documents/dfu/230WP7/english/230wp7/product/product.
Product Information file:///D|/My%20Documents/dfu/230WP7/english/230wp7/product/product.
Product Information RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230WP7/english/230wp7/product/product.
Installing Your LCD Monitor Installing Your LCD Monitor Front View • Produt Description Setting Up Front View Product Description and • Connecting Your Monitor • The Base Getting Started Optimizing • Performance • 1 To switch monitor's power On and Off 2 To access OSD menu 3 To adjust the OSD 4 To adjust brightness of the display 5 To adjust the OSD 6 AUTO Automatically adjust the horizontal position, vertical position, phase and clock setting RETURN TO TOP OF THE PAGE file:///D|/My%20Documen
Installing Your LCD Monitor Rear View 1 AC power input 2 DVI-I input 3 D-Sub 4 Kensington anti-thief lock 5 USB upstream and downstream RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1920 x 1200 @60Hz Note: You can check the current display settings by pressing the 'OK' button once. Go into the Product Information. The current display mode is shown on the item called RESOLUTION.
Installing Your LCD Monitor are provided to guide you through the installtion process. Click on the link to know more about this program. More about FP_setup4.3.exe RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230WP7/english/230wp7/install/install.
On-Screen Display On-Screen Display • Description of the OnScreen Display The OSD • Tree Description of the On Screen Display What is the On-Screen Display? • SmartControl This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display file:///D|/My%20Documents/dfu/230WP7/english/230wp7/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230WP7/english/230wp7/osd/osddesc.
On-Screen Display SmartControl It's a convenient tool for adjusting monitor performances and settings through a software interface. SmartControl displays a control panel for a user to adjust the brightness, contrast, color temperature, position and other settings. SmartControl also displays hardware information including the model, serial number, running hours from the interface. The SmartControl is deployed and installed in computers using Philips monitors.
On-Screen Display ● Click Philips SmartControl tab. 4. SmartControl Options ● Display and Sound By moving the sliding bar toward left or right, users will be able to adjust brightness, contrast, volume (if applicable), video noise (not applicable when using DVI-D input), and color temperatures. file:///D|/My%20Documents/dfu/230WP7/english/230wp7/osd/osddesc.
On-Screen Display ● ● Position Users can adjust the horizontal and vertical position of the screen by moving the sliding bar left and right. This function is disabled when using DVI-D (digit) input. Product Information Click Product Information in the left pane to view the product information stored in the monitor's memory. file:///D|/My%20Documents/dfu/230WP7/english/230wp7/osd/osddesc.
On-Screen Display ● General Click on general, users will be able to know some general information such as driver information, device information and monitor control. Within monitor control, users can click on Auto Setup to achieve optimum performance or click on factory reset to reset the parameters of the monitor. Such choices are disabled when using DVI-D (digit) input. Q&A Q1. What is SmartControl? A.
On-Screen Display install SmartControl to ensure proper driver is installed. Q3. The SmartControl functions well at the beginning, but somehow it stops working, what can I do? A. If the following actions were executed, the monitor driver may need to be re-installed. ● ● ● ● ● Change video graphic adapter to another one Update video driver Activities on OS, such as service pack or patch Run Windows Update and updated monitor and/or video driver Windows was booted with the monitor power off or disconnected.
Customer Care & Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Slovakia • Slovenia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • Peru • Uru
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ A Active matrix This is a kind of liquid crystal display structure in which switching transistors are attached to each pixel to control the on/off voltage. It produces a brighter and sharper display with a broader viewing angle than a passive matrix display. Also refer to TFT (thin film transistor). Amorphous silicon (a-Si) A semiconductor material that is used to make the thin film transistors (TFTs) layer of an active matrix LCD.
Glossary C CCFL(cold cathode fluorescent light) These are the fluorescent light tubes providing the light for the LCD module. These tubes are generally very thin, approximately 2 mm in diameter. Chromaticity That part of color specification, which does not involve illuminance. Chromaticity is two-dimensional and specified by pairs of numbers such as dominant wavelength and purity.
Glossary D D-SUB A VGA Analog input connector. Your monitor comes with a D-Sub cable. Digital Visual Interface (DVI) The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual data types that is display technology independent. The interface is primarily focused at providing a connection between a computer and its display device. The DVI specification meets the needs of all segments of the PC industry (workstation, desktop, laptop, etc.
Glossary H Hue The main attribute of a color that distinguishes it from other colors. For example, a color may have a green, yellow, or purple hue. Color defined as having hue are know as chromatic colors. White, black, and grays possess no hue. I IPS (In Plane Switching) A technique of improving the viewing angle of an LCD where the liquid crystal molecules are switched in the plane of the LCD layer rather than vertical to it.
Glossary RETURN TO TOP OF THE PAGE N Nit A unit of luminance equal to 1 cd/m2 or 0.292 ftL. P Pixel PICture Element; the smallest element on a computerized CRT or LCD image, and hence a display. Polarizer A light filter which only allows light waves of a certain rotation through. Polarized material with perpendicular filtering is used in LCDs to enclose the liquid crystal. The liquid crystal is then used as the medium which twists the light waves 90° in order to allow the light to pass through or not.
Glossary Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen. Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in the monitor's OSD.
Glossary install peripherals. And no need to go through the reverse process to unplug a device. In short, USB transforms today's "Plug-and-Pray" into true Plug-and-Play! Hub A Universal Serial Bus device that provides additional connections to the Universal Serial Bus. Hubs are a key element in the plug-and-play architecture of USB. The Figure shows a typical hub. Hubs serve to simplify USB connectivity from the user's perspective providing low cost and complexity.
Glossary Downstream The direction of data flow from the host or away from the host. A downstream port is the port on a hub electrically farthest from the host that generates downstream data traffic from the hub. Downstream ports receive upstream data traffic. Upstream The direction of data flow towards the host. An upstream port is the port on a device electrically closest to the host that generates upstream data traffic from the hub. Upstream ports receive downstream data traffic.
Download and Print Download and Print • Installing your LCD monitor driver Installing Your LCD monitor driver • Download and System requirements: Printing Instructions ● PC running Windows 95, Windows® 98, Windows® 2000 , Windows® Me, Windows® XP or later Installing ● Find your driver ".inf/.icm/.cat" at : /PC/drivers/ • FPadjust Program Read the "Readme.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print 1. With the manual file open, follow your printer's instructions and print the pages you need. RETURN TO TOP OF THE PAGE Installing FPadjust Program The FP Adjust program generates alignment patterns which will help you adjust monitor settings such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK.
FAQs (Frequently Asked Questions) • Safety and Troubleshooting • General FAQs FAQs (Frequently Asked Questions) • Screen General FAQs Adjustments • Compatibility Q: When I install my monitor what should I do if the screen shows 'Cannot display this video with Other mode'? Peripherals • LCD Panel A: Recommended video mode for Philips 23": 1920x1200 @60Hz. Technology • Ergonomics, 1. Unplug all cables, then connect your PC to the monitor that you used Ecology and previously. Safety 2.
FAQs (Frequently Asked Questions) with the "Display properties". Q: What if I get lost when I am making monitor adjustments? A: Simply press the OK button, then select 'Reset' to recall all of the original factory settings. Q: What is the Auto function? A: The AUTO adjustment key restores the optimal screen position, phase and clock settings by pressing of a single button – without the need to navigate through OSD (On Screen Display) menus and control keys.
FAQs (Frequently Asked Questions) Q: How should I clean the LCD surface? A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc. Q:Can I change the color setting of my monitor? A:Yes, you can change your color setting through OSD control as the following procedures, 1. Press "OK" to show the OSD (On Screen Display) menu 2.
FAQs (Frequently Asked Questions) and Clock for optimal performance. Q: When I install my monitor, how do I get the best performance from the monitor? A: 1. For best performance, make sure your display settings are set at 1920x1200@60Hz for 23". Note: You can check the current display settings by pressing the OSD OK button once. The current display mode is shown in OSD first page. 2.
FAQs (Frequently Asked Questions) benefits of USB. USB eliminates "case anxiety," the fear of removing the computer case to install circuit board cards -- that often requires adjustment of complicated IRQ settings -- for add-on peripherals. USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera, for example), and a joystick.
FAQs (Frequently Asked Questions) A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized electrons on fluorescent glass. Therefore, CRT monitors basically operate with an analog RGB signal. A TFT LCD monitor is a device that displays an input image by operating a liquid crystal panel. The TFT has a fundamentally different structure than a CRT: Each cell has an active matrix structure and independent active elements.
FAQs (Frequently Asked Questions) Magnetic Interference, especially magnetic fields. Also, since an LCD display utilizes relatively low power, its power supply is extremely quiet. RETURN TO TOP OF THE PAGE Ergonomics, Ecology and Safety Standards Q: What is the CE mark? A: The CE (Conformité Européenne) mark is required to be displayed on all regulated products offered for sale on the European market. This 'CE' mark means that a product complies with the relevant European Directive.
Troubleshooting Troubleshooting • Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.
Troubleshooting ● Image vibrates on the screen Check that the signal cable is properly connected to the graphics board or PC. Vertical flicker appears ● ● Press the Auto button. Eliminate the vertical bars using the Phase/ Clock of More Settings in OSD Main Controls. Horizontal flicker appears ● ● ● The screen is too bright or too dark ● An after-image appears ● An after-image remains after the power has been turned off.
Troubleshooting For further assistance, refer to the Consumer Information Centers list and contact Philips customer service representative. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230WP7/english/230wp7/safety/saf_troub.
Regulatory Information • TCO'99 Information • TCO'99 Environmental Requirements • TCO'03 Information • Recycling Information for Customers Waste Electrical and Electronic • EquipmentWEEE CE Declaration • of Conformity Automatic • Power Saving • Federal Communications Commission (FCC) Notice (U. S.
Regulatory Information • Philips End-ofLife Disposal Information for • UK only • Troubleshooting Other Related • Information • Frequently Asked Questions (FAQs) Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.
Regulatory Information The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma) as a consequence.
Regulatory Information ● ● Electromagnetic fields Noise emissions Ecology ● ● The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 Restrictions on ❍ chlorinated and brominated flame retardants and polymers ❍ heavy metals such as cadmium, mercury and lead.
Regulatory Information Tel: +886 (0) 3 222 6791 Mr. Maarten ten Houten - Senior Environmental Consultant Philips Consumer Electronics E-mail: marten.ten.houten@philips.com Tel: +31 (0) 40 27 33402 Mr. Delmer F. Teglas Philips Consumer Electronics North America E-mail: butch.teglas@philips.
Regulatory Information - ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for CRT Monitor) - ISO13406-2 (Ergonomic requirement for Flat Panel Display) - GS EK1-2000 (GS specification) - prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display) - MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields) - TCO'99, TCO'03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and Emission, TCO: Swedish Confederation of Professional Employees) for TCO vers
Regulatory Information ● ● ● ● Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Regulatory Information EN 55022 Compliance (Czech Republic Only) RETURN TO TOP OF THE PAGE MIC Notice (South Korea Only) Class B Device Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).
Regulatory Information requirements of standards PN-93/T-42107 and PN-89/E-06251. RETURN TO TOP OF THE PAGE North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. file:///D|/My%20Documents/dfu/230WP7/english/230wp7/safety/regs/regulat.
Regulatory Information Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Regulatory Information Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger. ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
Regulatory Information pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.
Other Related Information • Safety and Troubleshooting • FAQs Other Related Information • Troubleshooting Information for Users in the U. S. • Regulatory Information • Information for Users in the U.S • Information for Users Outside the U.S For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
Philips Pixel Defect Policy • Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips Pixel Defect Policy Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple Three adjacent lit sub pixels - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) (one white pixel) A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots. Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'.
Philips Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL 230WP7NS MODEL 1 lit subpixel 3 or fewer 2 adjacent lit subpixels 1 or fewer 3 adjacent lit subpixels (one white pixel) 0 Distance between two bright dot defects* 25 mm or more Total bright dot defects of all types BLACK DOT DEFECTS 3 or fewer ACCEPTABLE LEVEL 230WP7NS MODEL 1 dark subpixel 5 or fewer 2 adjacent dark subpixels 2 or fewer 3 adjacent dark subpixels 1 or fewer Distance between two black dot defects* Total blac
Rotating the Monitor • Rotating the Monitor • Rotating Your Computer's Operating System Rotating the Monitor Rotating the Monitor Before rotating the monitor, remove the pin on the back of the base and raise the monitor to a higher vertical height adjustment to avoid hitting the bottom edge of the monitor when rotating. file:///D|/My%20Documents/dfu/230WP7/english/230wp7/product/rotate.
Rotating the Monitor file:///D|/My%20Documents/dfu/230WP7/english/230wp7/product/rotate.
Rotating the Monitor Rotating Your Computer's Operating System After rotating, the procedures below help rotate the image from your operation system. 1. Right-click on the desktop then click on Properties. 2. Select the Settings tab and click Advanced. then find your graphic card. 3. For ATI graphics cards: Select the Rotation tab and set the preferred rotation. For nVidia graphics cards: Click the nVidia tab; in the lefthand column select NVRotate and then select the preferred rotation.
Setting up and Connecting Your Monitor Setting Up and Connecting Your Monitor Your LCD Monitor : • Front View Product Accessory Pack Description • Accessory Unpack all the parts. Pack • Setting Up and Connecting Your Monitor • Getting Started Power cord • Optimizing Performance • The Base USB cable VGA signal cable DVI cable Apple Macintosh adaptor (US Model) EDFU pack RETURN TO TOP OF THE PAGE Connect to PC Connect the power cord and DVI cable to the back of the monitor firmly.
Setting up and Connecting Your Monitor If you use an Apple MacintoshTM, you need to connect the special Apple Macintosh adapter to one end of the monitor signal cable. Connect the cables to the back of your computer by following these steps: (a) Turn off your computer and unplug its power cord. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord on your computer and your monitor into a nearby outlet.
The Base The Base Your LCD Monitor : • Front View 1) Place the monitor face down on a smooth surface taking care to avoid scratching or damaging the Product screen. Description • Accessory Pack • Setting up and connecting Do not release the pin your monitor before the base stand is • Getting firmly fixed to the base Started column. • Optimizing Performance 2) Hold the monitor base with both hands and firmly fix the base plate into four-pronged base attachments.
The Base 3)Fastening base stand with the monitor. VESA Standard Mounting 1) Place monitor face down on a smooth surface. 2) Unscrew the 4 screws at the base. file:///D|/My%20Documents/dfu/230WP7/english/230wp7/install/base.
The Base 3) VESA mounting holes 4) Install the wall mount file:///D|/My%20Documents/dfu/230WP7/english/230wp7/install/base.
The Base RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230WP7/english/230wp7/install/base.
Getting Started Your LCD Monitor : • Front View Product Description • Setting Up and Connecting Your Monitor • Getting Started • Optimizing Performance Getting Started Getting Started Use the information file ( .inf) for Windows® 95/98/2000/Me/XP or later The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows® 95/98/2000/Me/XP. This information file ( .
Getting Started 6. 7. 8. 9. 10. 11. - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next' and then click on 'Have disk...'.
Getting Started dialog box. If your Windows® 95/98/2000/Me/XP version is different or you need more detailed installation information, please refer to your Windows® 95/98/2000/Me/XP user's manual. RETURN TO TOP OF THE PAGE file:///D|/My%20Documents/dfu/230WP7/english/230wp7/install/gt_start.
Your Philips F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
Your Philips F1rst Choice Warranty ● ● ● ● Reception problems caused by signal conditions or cable or antenna systems outside the unit; Defects caused by abuse or misuse of the monitor; Product requires modification or adaptation to enable it to comply with local or national technical standards, which apply in countries for which the product was not originally designed, manufactured, approved and/or authorized. Therefore always check whether a product can be used in a specific country.
Your Guarantee in Central and Eastern Europe Your Guarantee in Central and Eastern Europe Dear Customer, Thank you for purchasing this Philips product, which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts during a period of 36 months from date of purchase.
Your Guarantee in Central and Eastern Europe which apply in countries for which the product was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific country. Just a click away In case of any problems, we advise you to read the operating instructions carefully or go to the www. philips.com/support website for additional support.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee Your Philips F1rst Choice Warranty(USA) Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
United States Guarantee Your warranty does not cover: ● ● ● ● ● ● labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product. product repair and/or part replacement because of misuse, accident, unauthorized repair or other cause not within the control of Philips Consumer Electronics. reception problems caused by signal conditions or cable or antenna systems outside the unit.
United States Guarantee (In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty. But, because some states do not allow limitations on how long an implied warranty may last, this limitation may not apply to you.) TO GET WARRANTY SERVICE IN CANADA...
United States Guarantee ● ● ● Other cards installed Having the following information available will also help speed up the process: Your proof of purchase indicating: date of purchase, dealer name, model and product serial number. The full address to which the swap model should be delivered. Just a phone call away Philips’ customer help desks are located worldwide. Within the U.S.
F1rst Choice Contact Information F1rst Choice Contact Information Country Telephone number Tariff Austria 0820 901115 0.20 Belgium 070 253 010 0.17 Denmark 3525 8761 Local call tariff Finland 09 2290 1908 Local call tariff France 08 9165 0006 0.23 Germany 0180 5 007 532 0.12 Greece 00800 3122 1223 Local call tariff Ireland 01 601 1161 Local call tariff Italy 199 404 042 0.25 Luxembourg 26 84 30 00 Local call tariff The Netherlands 0900 0400 063 0.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Belarus • Bulgaria • Croatia • Czech Republic • Estonia • Dubai • Hong Kong • Hungary • India • Indonesia • Korea • Latvia • Lithuania • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Romania • Russia • Serbia & Montenegro • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey • Ukraine
Consumer Information Centers ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE-12618 Tallinn Tel: +372 6519900 www.ee.invia.fujitsu.com HUNGARY Serware Szerviz Vizimolnár u. 2-4 HU - 1031 Budapest Tel: +36 1 2426331 Email: inbox@serware.hu www.serware.hu LATVIA ServiceNet LV Jelgavas iela 36 LV - 1055 Riga, Tel: +371 7460399 Email: serviss@servicenet.lv LITHUANIA ServiceNet LT Gaiziunu G. 3 LT - 3009 KAUNAS Tel: +370 7400088 Email: servisas@servicenet.lt www.servicenet.
Consumer Information Centers SLOVAKIA Datalan Servisne Stredisko Puchovska 8 SK - 831 06 Bratislava Tel: +421 2 49207155 Email: servis@datalan.sk SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.Zytnia 1 PL - 05-500 Piaseczno Tel: +48 22 7501766 Email: servmonitor@zolter.com.pl www.zolter.com.pl RUSSIA Tel: +7 095 961-1111 Tel: 8-800-200-0880 Website: www.philips.ru TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.
Consumer Information Centers UKRAINE Comel Shevchenko street 32 UA - 49030 Dnepropetrovsk Tel: +380 562320045 www.csp-comel.com Latin America ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V. Vedia 3892 Capital Federal CP: 1430 Buenos Aires Phone/Fax: (011)-4544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda.
Consumer Information Centers COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone:(01)-8000 111001 (toll free) Fax : (01)-619-4300/619-4104 MEXICO Consumer Information Centre Norte 45 No.669 Col. Industrial Vallejo C.P.02300, -Mexico, D.F. Phone: (05)-3687788 / 9180050462 Fax : (05)-7284272 PARAGUAY Av. Rca. Argentina 1780 c/Alfredo Seiferheld P.O.
Consumer Information Centers URUGUAY Rambla O'Higgins 5303 Montevideo Uruguay Phone: (598) 619 66 66 Fax: (598) 619 77 77 Customer Desk: Phone: 0004054176 VENEZUELA Industrias Venezolanas Philips S.A. Apartado Postal 1167 Caracas 1010-A Phone: (02) 2377575 Fax : (02) 2376420 Canada CANADA Philips Electronics Ltd.
Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA SHANGHAI Rm 1007, Hongyun Building, No. 501 Wuning road, 200063 Shanghai P.R.
Consumer Information Centers INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr. A Besant Road, Worli Bombay 400 025 CALCUTTA Customer Relation Centre 7 justice Chandra Madhab Road Calcutta 700 020 MADRAS Customer Relation Centre 3, Haddows Road Madras 600 006 NEW DELHI Customer Relation Centre 68, Shivaji Marg New Dehli 110 015 INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav.
Consumer Information Centers KOREA Philips Consumer Service Jeong An Bldg. 112-2 Banpo-dong, Seocho-Ku Seoul, Korea Customer Careline: 080-600-6600 Phone: (02) 709-1200 Fax : (02) 595-9688 MALAYSIA After Market Solutions Sdn Bhd, Philips Authorised Service Center, Lot 6, Jalan 225, Section 51A, 46100 Petaling Jaya, Selangor Darul Ehsan, Malaysia.
Consumer Information Centers SINGAPORE Accord Customer Care Solutions Ltd Authorized Philips Service Center Consumer Service 620A Lorong 1 Toa Rayoh Singapore 319762 Tel: +65 6882 3999 Fax: +65 6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 13F, No. 3-1 Yuan Qu St., Nan Gang Dist., Taipei 115, Taiwan Phone: 0800-231-099 Fax : (02)-3789-2641 THAILAND Philips Electronics (Thailand) Ltd.
Consumer Information Centers SOUTH AFRICA PHILIPS SA (PTY) LTD Customer Care Center 195 Main Road Martindale, Johannesburg P.O. box 58088 Newville 2114 Telephone: +27 (0) 11 471 5194 Fax: +27 (0) 11 471 5123 E-mail: customercare.za@philips.com Middle East DUBAI Philips Middle East B.V. Consumer Information Centre P.O.Box 7785 DUBAI Phone: (04)-335 3666 Fax : (04)-335 3999 file:///D|/My%20Documents/dfu/230WP7/english/warranty/warcic.
