B line 230B8 www.philips.
Table of Contents 1. Important �������������������������������������� 1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the monitor �������������� 5 2.1 Installation ������������������������������������ 5 2.2 Operating the monitor �������������� 6 2.
1. Important • Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics. • Do not block the ventilation holes on the cabinet. • When positioning the monitor, make sure the power plug and outlet are easily accessible. • If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation.
1. Important be better than a 15-minute break every two hours. Try to keep your eyes from eye strain while using the screen for a constant period of time by : not expose the monitor to dust, rain, water, or excessive moisture environment. • If your monitor gets wet, wipe it with dry cloth as soon as possible. • If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord.
1. Important Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. 2.1 Installation Package contents B line 230B8 278E9 Quick Start Register your product and get support at www.philips.com/welcome 2. Hold the stand with both hands. (1) Gently attach the base to the stand. Monitor User’s Manual 使用 前请阅读使用说明 Contents: User’s Manual Drivers Ch i na OP ©T .
2. Setting up the monitor 2.2 Operating the monitor Connecting to your PC Description of the control buttons 11 1 2 3 4 5 6 7 8 9 9 3 1 Power Switch 2 AC power input 3 DisplayPort input 7 6 4 DVI input 5 4 2 1 Switch monitor’s power ON and OFF. 5 HDMI input 6 VGA input 8 Earphone jack Access the OSD menu. Confirm the OSD adjustment. 9 Kensington anti-theft lock Adjust the OSD menu. 7 Audio input Adjust the brightness level. Connect to PC 1.
2. Setting up the monitor Description of the On Screen Display The OSD Menu Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. What is On-Screen Display (OSD)? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window.
2. Setting up the monitor Height adjustment Resolution notification This monitor is designed for optimal performance at its native resolution, 1920 x 1200 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 x 1200 @ 60 Hz for best results. Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. 100mm 100mm 2. Place the monitor face down on a smooth surface.
3. Image Optimization 2. Keep pressing to toggle among EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode, Off. 3. Image Optimization 3.1 SmartImage 3. The SmartImage on screen display will remain on screen for 5 seconds, or you can also press "OK" to make confirmation. There are multiple selections: EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode, Off.
3. Image Optimization outstanding clarity in vibrant colors - all without artifacts and faded colors. 3.2 SmartContrast • Movie: Ramped up luminance, deepened color saturation, dynamic contrast and razor sharpness displays every details in darker areas of your videos without color washout in brighter areas maintaining a dynamic natural values for the ultimate video display.
4.Adaptive Sync • • • • 4. Adaptive Sync Adaptive Sync AMD Radeon R9 285 AMD Radeon R7 260X AMD Radeon R7 260 ■■ Processor A-Series Desktop and Mobility APUs • • • • • • • • • PC gaming has long been an imperfect experience because GPUs and monitors update at different rates. Sometimes a GPU can render many new pictures during a single update of the monitor, and the monitor will show pieces of each picture as a single image. This is called “tearing.
5.Technical Specifications 5. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio (typ.) Optimum Resolution Viewing Angle Display Colors Flicker Free Picture Enhancement Vertical Refresh Rate Horizontal Frequency sRGB LowBlue Mode EasyRead Adaptive Sync Connectivity Signal Input Input Signal Audio In/Out Convenience Built-in speaker IPS Technology W-LED 22.5" W (57.2 cm) 16:10 0.25425 (H) mm x 0.
5.
5.Technical Specifications Environmental and energy ROHS Packaging Specific Substances Cabinet Color Finish YES 100% recyclable 100% PVC BFR free housing Black Texture Note This data is subject to change without notice. Go to www.philips.com/support to download the latest version of leaflet.
5.Technical Specifications 5.1 Resolution & Preset Modes Maximum Resolution 1920 x 1200 @ 60 Hz (analog input) 1920 x 1200 @ 75 Hz (digital input) Recommended Resolution 1920 x 1200 @ 60 Hz H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.36 1024 x 768 60.00 60.02 1024 x 768 75.03 44.77 1280 x 720 59.86 63.89 1280 x 1024 60.
6.Power Management 6. Power Management If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
7.Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 7. Customer care and warranty 7.
7.Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
7.
7.Customer care and warranty 7.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For Warranty Period please refer to Warranty Statement in Important Information Manual. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center.
8.Troubleshooting & FAQs • 8. Troubleshooting & FAQs AUTO button doesn't function • 8.1 Troubleshooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. Visible signs of smoke or sparks No Picture (Power LED not lit) Make sure the power cord is plugged into the power outlet and into the back of the monitor.
8.Troubleshooting & FAQs Horizontal flicker appears Image appears distorted. Text is fuzzy or blurred. • • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode. Green, red, blue, dark, and white dots appears on the screen • Image appears blurred, indistinct or too dark • • You can adjust “power on” light using the power LED Setup in OSD main Controls.
8.Troubleshooting & FAQs you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. 8.2 General FAQs Q1: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? Q4: How do I adjust the resolution? Ans.: Your video card/graphic driver and monitor together determine the available resolutions. You can select the desired resolution under Windows® Control Panel with the "Display properties". Ans.
8.Troubleshooting & FAQs • Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below. 1. Color Temperature: The settings are Native, 5000K, 6500K, 7500K, 8200K, 9300K and 11500K. With settings in the 5000K range the panel appears "warm, with a redwhite color tone", while a 11500K temperature yields "cool, bluewhite toning". Ans.: Yes, the monitors are Plug-andPlay compatible with Windows 10/8.1/8/7, Mac OSX.
8.Troubleshooting & FAQs Q13: How to unlock/lock my hot key? Ans.: Please press for 10 seconds to unlock/lock the hot key, by doing so, your monitor pops out “Attention” to show the unlock/lock status as shown below illustrators. Q14: Where can I find Important Information manual mentioned in EDFU? Ans.: Important Information manual can be download on the Philips website support page.
2019 © TOP Victory Investment Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
