Register your product and get support at www.philips.
Model Serial www.philips.com/support Österreich 0810 000205 €0.07 pro Minute België/Belgique 078250145 €0.06 Per minuut/Par minute България +3592 489 99 96 Местен разговор Hrvatska 01 6403 776 Lokalni poziv Česká republika 800142840 Bezplatný hovor Danmark 3525 8759 Lokalt opkald Estonia 6008600 local Suomi 09 2311 3415 paikallispuhelu France 0821 611655 €0.09 Par minute Deutschland 01803 386 852 €0.
Contents 1 Notice 2 2 Important 4 3 TV overview 6 Side controls and indicators 6 Guest remote control 7 Basic TV menus 8 Watch TV 10 Watch a connected device 12 4 Use more of your product 13 Use Teletext 13 Favourite channels 14 Use EPG 14 Use timers 15 Use locks 15 Use the TV clock 16 Use subtitles 16 Access multimedia 17 Use Scenea 18 Universal access 18 Back connector 38 Side connector 39 Connect a computer 39 Use a Conditional Access Module 40 Use Philips EasyLink 41 Use a Ken
1 Notice 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
1. 2. Note Eng lis h Philips plays an active role in the development of international EMF and safety standards, enabling Philips to anticipate further developments in standardisation for early integration in its products. Mains fuse (UK only) This TV is fitted with an approved moulded plug. Should it become necessary to replace the mains fuse, this must be replaced with a fuse of the same value as indicated on the plug (example 10A).
2 Important Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply. Safety • Risk of electric shock or fire! • Never expose the TV to rain or water. Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use.
• • • • • Risk of injury, fire or power cord damage! Never place the TV or any objects on the power cord. To easily disconnect the TV power cord from the power outlet, ensure that you have full access to the power cord at all times. When you disconnect the power cord, always pull the plug, never the cable. Disconnect the TV from the power outlet and aerial before lightning storms. During lightning storms, never touch any part of the TV, power cord or aerial cable.
3 TV overview Side controls and indicators This section gives you an overview of commonly used TV controls and functions. 1 Please read section 3 to 6 to set the basic consumer menu first, then follow the instructions in section 7 to set the Professional mode menu. 2 3 4 a ”+/- : Increases or decreases volume.In the home menu, press these buttons to move horizontally. b Home : Accesses the home menu. Press again to launch an activity in the home menu.
Guest remote control a s b r c d b a EPG/TELETEXT Accesses the browse menu to select TV channel list, the Electronic Programme Guide and teletext. c e f q p d AV Selects connected devices. h e EXIT/MENU Accesses the home menu. i f OPTION Options menus offer convenient settings related to what is on screen. k g OK Confirms an entry or selection. h ▲▼◄► (Navigation buttons) Navigates menus and selects items. i l n ALARM Lauches [Alarm time] menu.
o ”+/- (Volume +/-) Increases or decreases volume. p BACK • Returns to a previous screen. • Returns to the previously viewed channel. Remote control usage When using the remote control, hold it close to the TV and point it at the remote control sensor. Make sure that the line-of-sight between the remote control and TV is not blocked by furniture, walls or other objects. q Colour buttons • Selects tasks or options. • When Professional mode is On, press to operate Multi remote control function.
Browse The browse menu gives you easy access to: • Electronic programme guide • TV channel list • Teletext To access the browse menu, while watching TV, press a. 1. 2. Press the Navigation buttons to select an item: • [Programme guide] : Accesses the Electronic Programme Guide. • [Channel list] : Accesses the TV channel list. • [Text] : Accesses teletext. Press OK to confirm your choice. Channel list The channel list displays the TV channels and possible radio stations installed on your TV. 1. 2. 3. 4.
Options Option menus offer convenient settings related to what is on-screen. 1. 2. Press to see what options are available. To exit, press again. To switch to standby • Press B (Standby-On) on the remote control. »» The front LED indicator switches to red. To switch off • Press B POWER at the side of the TV. »» The standby indicator switches off. Watch TV Swith on/off or to standby Tip •• Though your TV consumes very little power when in standby, energy continues to be consumed.
• • Press a, then select [Channel list] to use the channel list. Press to return to the previouslyviewed channel. Enter a channel number using the Numeric buttons. To view analogue or digital channels only Filter the channel list to access analogue or digital channels only. 1. 2. In the channel list, press . Use the [Sound] menu to adjust headphone volume. For more information, see Setup the TV > Change picture and sound settings > More sound settings (Page 30). Use Smart picture settings 1. 2. 3.
4. 5. • [Standard] : Adjusts sound settings to suit most environments and types of audio. • [News] : Applies sound settings ideally suited for spoken audio, such as the news. • [Movie] : Applies sound settings ideally suited for movies. • [Game] : Ideal settings for gaming. • [Drama] : Applies sound settings ideally suited for drama. • [Sports] : Applies sound settings ideally suited for sports. Press OK to confirm your choice. Press to exit. • [Unscaled] : Provides maximum detail for PC.
Use Teletext 3. Select a page 1. 2. 3. • • • 4. Select [Text], then press OK. Select a page by: Entering the page number with the Numeric buttons. Pressing ▲ or ▼ to view the next or previous page. Pressing the Colour buttons to select a colour coded item. to exit teletext. When in teletext, press to exit the options menu. Some digital TV broadcasters have several teletext languages available. You can set your primary and secondary language. 1. 2. 3. Press .
Use digital teletext Some digital TV broadcasters offer dedicated digital text or interactive services on their digital TV channels, for example, BBC1. When in digital teletext: • Press the Navigation buttons to select or highlight items. • Use the Colour buttons to select an option, then press OK to confirm or activate. Note •• Digital text services are blocked when subtitles are broadcast and [Subtitles] are enabled. Read Use more of your TV > Use subtitles (Page 25). Use Teletext 2.5 Teletext 2.
Use the EPG options menu to set or clear reminders, change day and access other useful EPG options. Depending on the broadcast service, these options are available only for seven or eight days. 1. 2. When in EPG, press . Press the Navigation buttons and OK to select and adjust one of the following settings: • [Set reminder] : Sets programme reminders. • [Clear reminder] : Clears programme reminders. • [Change day] : Sets the EPG day. Select [Today], [Next day] or [Previous day].
3. 4. Enter the child lock code with the Numeric buttons. Select an age rating, then press OK. All programmes beyond the selected age rating are blocked. Lock or unlock channels 1. 2. 3. In the child lock menu, select [Channel lock]. Enter the child lock code with the Numeric buttons. The [Channel lock] menu appears. Select channels to lock or unlock. Set or change the child lock code Set or change the child lock code 1. 2. In the child lock menu, select [Set code] or [Change code].
4. Enter the three number page number of the subtitles page (usually ‘888’). Press to access or exit the following settings: • [Show info] : Displays the file information. • [Stop] : Stops slideshow. • [Rotate] : Rotates the file. • [Repeat] : Repeats the slideshow. • [Play once] : Plays the file once. • [Shuffle off] / [Shuffle on] : Enables or disables random display of pictures in the slideshow. • [Slideshow speed] : Sets the display time for each picture in the slideshow.
• [Stop] : Stops playback. • [Repeat] : Repeats a video. • [Shuffle on] / [Shuffle off] : Enables or disables random play of videos. Note •• If the sleep timer is off, the wallpaper is displayed for 240 minutes. Otherwise, it is displayed for the duration of the sleeptimer. For more information on the sleeptimer, see Use more of your TV > Use timers and locks > Sleeptimer (Page 24).
Some digital TV channels broadcast special audio adapted for people who are visually impaired. The normal audio is mixed with extra commentary. To switch on visually impaired audio (if available) 1. 2. 3. 4. While watching TV, press . Select [Universal access], and press the green button to enter [Visually impaired]. Use the following buttons to select: • Red - [Off] : Turn off visually impaired audio. • Green - [Speakers] : Hear visually impaired audio from speakers only.
5 Set up the TV 4 5 Press OK to confirm your choice. Press to exit. More picture settings Change picture and sound settings 1 2 3. Settings assistant Use the settings assistant to guide you through the picture and sound settings. 1. 2. 3. While watching TV, press . Select [Setup] > [Quick picture and sound settings], then press OK. Select [Start], then press OK. Follow the on-screen instructions to choose your preferred settings. Smart picture settings 1 2 3 20 Press .
• [Reset] : Resets to factory default settings. • [Bass] : Adjusts the bass level. • [Treble] : Adjusts the treble level. • [Surround] : Enables spatial sound. • [Headphones volume] : Adjusts headphone volume. • [Auto volume leveling] : Automatically reduces sudden volume changes, for example, when switching channels. • [Balance] : Adjusts the balance of the left and right speakers to best suit your listening position.
Change channel settings Reorder channels After installation, you may want to reorder the channel list to suit your preference. 1. 2. 3. 4. 5. 6. 7. While watching TV, press a. Select [Channel list], then press OK. In the channel list, press . Select [Reorder], then press OK. Select the channel to reorder, move it to the desired location, then press OK. Select [Insert] to insert the channel into the desired location, [Swap] to swap location with another channel or [Cancel] to cancel the reorder.
1. 2. • Press . Select [Setup] > [Channel settings] or [Satellite settings] > [Channel installation] > [Channel update message] > [Off], then press OK. To disable automatic updates In the [Channel installation] menu, select [Automatic channel update] > [Off]. Install channels Automatic install When the TV was switched on for the first time, a full installation of channels was performed. You can redo this full installation again to set your language, country and install all available TV channels.
4. 3. 4. Select one of the following settings: • [Antenna (DVB-T)] : Access free-toair antenna or digital DVB-T channels. • [Cable] : Access cable or digital DVB-C channels. Press OK to confirm your choice. The Navigation buttons to select [Search]. Press OK to automatically search for the next channel. • 3. 4. Press to exit. The TV switches to the selected channel list.
(For certain models only) If your satellite is connected to the SAT connector, you can receive satellite channels. 1. 2. 3. 4. While watching TV, press 1. 2. 3. . Select [Setup] > [Search for satellite] > [Reinstall channels]. Follow the on-screen instructions to complete the installation of satellite channels. Once complete, select [Finish], and then press OK. Fine-tune analogue channels If the reception of an analogue TV channel is poor, try fine tuning the TV channel. 1. 2. 3. 4. 5. Press .
Change other settings Energy-efficient settings 1. 2. While watching TV, press the green button. Select one of the following settings, then press OK: • [Energy saving] : Applies a combination of picture settings to reduce energy consumption. • [Mute screen] : Turns off the TV display. ‘Muting’ the screen saves energy if you just want to listen to audio from the TV. Audio lip sync Turn on digital audio lipsync to automatically sync the image on your TV to audio from a connected Home Theatre System. 1. 2.
The flexibility to change settings is limited if the TV location is set to [Shop] mode. Set the TV location to [Home] mode to access all TV settings. 1. 2. 3. While watching TV, press Press Select [Setup] > [TV settings] > [Preferences] > [Location] > [Home] or [Shop], then press OK. Restart the TV. Specific TV settings are applied to suit the mounting location of the TV. In the [Preferences] menu, select [TV placement] > [On a TV stand] or [Wall mounted], then press OK. .
On-screen Help: Update Before updating the on-screen Help, ensure you have the following: • An empty USB flash drive. The USB flash drive must be FAT or DOS-formatted. • Do not use a USB hard drive. • A PC with Internet access. • An archive utility that supports the ZIP file format (for example, WinZip for Microsoft Windows or Stufflt for Macintosh). Before updating Help, check the current version installed on your TV.
Professional Setup Remote control (22AV8573 optional) Introduction Included in this TV is a special functional mode that allows the TV to be configured for commercial application. This feature is called Professional mode. This section has been designed to help install and operate this TV in Professional mode. Before reading this section, please also read section 3 to set the basic functionality of this TV. Benefits of Professional mode This TV is specially designed to operate in Professional Mode.
Professional mode options This paragraph describes the functionality of each item in the Professional mode setup menu Enter the next layer by pressing [OK], or [>]. Return to a previous level by pressing [<]. Navigate in the current layer by pressing [^], or [v].
RF Download Layer 2 Enter TV Channel Setup Layer 3 USB to TV TV to USB SW types SSB Firmware / SSB NVM / Standby Firmware / ThemeTV / All Frequency, Medium, Service ID, ONID, NID, TSID, Symbol Rate, Modulation Program Info Start Download Layer 4 Eng lis h Layer 1 Channel setup Store Settings Smart Clone [Welcome message] Setup settings PBS Setup [PBS Setup menu language] Select menu language to be English, French, German or Italian.
[OSD display] Set this function to show or hide screen information. [Off]: Screen information is suppressed. [On]: Normal screen information is displayed.
[Manual]: The clock time is set using the Time Setting option. [Country dependent]: During cold start the Clock time is retrieved from the Download Program channel before displaying the tuned channel, and country dependent settings are made (UTC+LTO). During a ‘going to Standby cycle’, the clock time is updated as well. consumption then the Green mode). [Green]: The TV will slower turn on (show startup channel) then the Fast. (This mode is having less power consumption then the Fast mode).
[On]: Show ThemeTV on the display after pressing the ThemeTV button on the RC. [Off] ThemeTV disabled. [Startup] Show ThemeTV on startup and able to showd ThemeTV by pressing the TTV button on the RC. [VSecure] VSecure is the hospitality content scrambling method used by the Philips Hospitality TVs. With its internal VSecure Authorization key a VSecure Unprotect key can be generated. If this VSecure Unprotect key is stored in the TV, the TV is able to descramble protected content.
[Show hidden channels] Restore the factory picture and sound setting. Channel installation is not changed. Presents the hidden channels in the Channel Grid as blanks. These blank channels can NOT be selected by Channel number or P+/P-. If activated new a second level for [Options] is available: Channel Setup Exit Unhide All Blank Channels The Channel Setup function depends on the state of the PBS Mode: the display of video on the TV, but does not affect the audio output.
Smart Clone [Program Info] Place a USB Memory stick in the USB side I/O connector Layer 1 Smart Clone Layer 2 USB to TV Layer 3 OK or > TV will read and store Cloning data from USB stick Layer 1 Smart Clone Layer 2 TV to USB Layer 3 OK or > TV will store Cloning data to USB stick This function is to set the necessary DVB parameters to locate the proper VSecure RF channel to load the VSecure RF Static or RF Dynamic key(s): [Frequency] [Medium] [Service ID] [ONID] [NID] [TSID] [Symbol Rate] [Modulati
Eng lis h 6b Guest mode instruction Introduction When this television is configured as a professional television, the guest is having no access to TV functionality that can influence TVs expected behavior. The guest will not have access to menus that can change the channel configuration, nor can he, as example, put the TV on a louder audio level then is permitted in the BDS Mode setting. This section describes the functionality available to the guest.
[External]: [Options]: [Info]: Access to options for the current selection. Access to the home menu.
page intendendly blank
7 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start. b DIGITAL AUDIO OUT Audio and video output to analogue devices such as another TV or a recording device. DIGITAL AUDIO OUT Note •• Different types of connectors may be used to connect a device to your TV, depending on availability and your needs. c HDMI 1 Digital audio and video input from highdefinition digital devices such as Blu-ray players.
Side connector c HDMI (Only for TVs 26 inches and larger) Digital audio and video input from highdefinition digital devices such as Blu-ray players. 1 2 3 a COMMON INTERFACE Slot for a Conditional Access Module (CAM). Connect a computer Before you connect a computer to the TV • Set the screen refresh rate on your computer to 60Hz. • Select a supported screen resolution on your computer.
Use a Conditional Access Module DVI-HDMI cable • For TV of size 22 inch PC IN(AUDIO) For TV of size 26 inch and larger AUDIO IN : LEFT / RIGHT HDMI 1 / DVI A Conditional Access Module (CAM) is provided by digital TV service operators to decode digital TV channels. Note DVI operator on how to insert a smart card into the Conditional Access Module.
1. 2. After inserting and activating the CAM, press . Press Navigation buttons to select [Common interface]. »» Applications provided by the digital TV service operator appear on the screen. Use one-touch play 1 Use one-touch standby 1 Note •• This menu option is available only if the CAM is inserted and activated correctly. Use Philips EasyLink Your TV supports Philips EasyLink, which enables one-touch play and one-touch standby between EasyLink-compliant devices.
8 Product information Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.
Eng lis h Supported TV mounts To mount the TV, purchase a Philips TV mount or a VESA-compatible TV mount. To prevent damage to cables and connectors, be sure to leave a clearance of at least 2.2 inches or 5.5cm from the back of the TV. Warning •• Follow all instructions provided with the TV mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper TV mounting that results in accident, injury or damage.
9 Troubleshooting This section describes commonly encountered issues and accompanying solutions. General TV issues The TV does not switch on: •• Disconnect the power cable from the power outlet. Wait for one minute then reconnect it. •• Check that the power cable is securely connected. The remote control is not working properly: •• Check that the remote control are correctly inserted according to the +/orientation. •• Replace the remote control batteries if they are flat or weak.
Sound issues There is a picture but sound quality is poor: Note •• If no audio signal is detected, the TV automatically mutes the audio output — this does not indicate malfunction. •• Check that all cables are properly connected. •• Check that the volume is not set to 0. •• Check that the sound is not muted. There is a picture but the sound quality is poor: •• Check that the sound settings are correctly set.
Index A age rating Alarm ALARM audio language Audio lip sync B H 15 15 7 23 26 44 35 C Channel list PayTV channel Troubleshooting clock Computer Connect display resolutions Troubleshooting Consumer setup 37 46 16 41 44 47 33 D Digital channels CAM Display resolutions 42 44 Installation K EasyLink disable Enable HDMI-CEC in one-touch play one-touch standby F factory settings EN 43 43 35 43 43 21 43 L Language Troubleshooting Lock Kensington lock Local KB lock RC l
P picture format picture setting picture settings POWER Technical specifications Professional mode Activate Options PBS mode Store settings 12 20 20 10 44 30 31 33 37 R Remote control Multi remote control Professional Setup Remote control RC lock Remote control usage Technical specifications Troubleshooting Rename channel Reorder channels S Safety Scenea Selectable AV Shop mode Skip scrambled signals Sleep timer Smart card Smart picture Smart power Smart sound sound settings
© 2009 Koninklijke Philips Electronics N.V. All rights reserved.
