Philips Professional and Business Solution 22HFL3350D 26HFL3350D 32HFL3350D EN SETUP MANUAL
7.12 Set auto scart �������������������������������������� 21 1 Important ������������������������������������������� 4 7.14 Select monitor out ������������������������������ 21 1.1 Safety ������������������������������������������������������ 4 7.15 Select blank current channel ���������������� 22 1.2 Screen care �������������������������������������������� 5 7.16 Save settings ���������������������������������������� 22 1.
2008 © Koninklijke Philips Electronics N.V. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system.
Mains fuse (UK only) EN This TV is fitted with an approved moulded plug. Should it become necessary to replace the mains fuse, this must be replaced with a fuse of the same value as indicated on the plug (example 10A). 1. Remove fuse cover and fuse. 2. The replacement fuse must comply with BS 1362 and have the ASTA approval mark. If the fuse is lost, contact your dealer in order to verify the correct type. 3. Refit the fuse cover.
1 Important • Two people are required to lift and carry a TV that weighs more than 55 lbs. Read and understand all instructions before you use the TV. If damage is caused by failure to follow instructions, the warranty does not apply. 1.1 • • If you stand mount the TV, use only the supplied stand. Secure the stand to the TV tightly. Place the TV on a flat, level surface that can support the weight of the TV and stand. Safety Risk of electric shock or fire! • Never expose the TV to rain or water.
Risk of hearing damage! Avoid using earphones or headphones at high volumes or for prolonged periods of time. • Never allow children to climb on or play with the TV. • Place the TV where it cannot be pushed, pulled over or knocked down. • If the TV is transported in temperatures below 5°C: crossed-out wheel bin symbol attached to a product, it means the product is covered by the European Directive 2002/96/EC: • Never dispose this product with other household waste.
2 Your TV 2.1 Connection overview 9 10 54 3 2 1 11 12 13 14 8 15 6 7 1. EXT 1 First SCART connector for DVD players, VCRs, digital receivers, game consoles and other SCART devices. Supports Audio L/R, CVBS in/out, RGB 2. EXT 2 Second SCART connector. Supports Audio L/R, CVBS in/out. 6. HDMI 1/2/3 HDMI input connectors for Blu-ray disc players, digital receivers, game consoles and other high-definition devices. 7.
2.1.1 Side controls and indicators EN 13. USB USB connector for storage devices. 14. HDMI Additional HDMI connector for mobile high-definition devices. 4 VOLUME 15. COMMOM INTERFACE Slot for Conditional Access Modules. 3 MENU DDNote Refer to the user manuals for the respective devices for details of connection. 2 PROGRAM 1 6 POWER 5 1. POWER 2. PROGRAM +/3. MENU 4. VOLUME +/5. Power indicator/remote control sensor 6.
3 Remote control For advanced information about the remote control, see Chapter 5 Remote control overview. Guest mode remote control Setup remote control This remote control may be purchased separately for Institutional TV/Professional and Business Solutions features and SmartCard settings. For setup and configuration purposes.
Get started This section helps you position and install the TV. 4.1 Position the TV In addition to reading and understanding the safety instructions in Section 1.1, consider the following before positioning your TV: • The ideal viewing distance for watching TV is three times its screen size. • Position the TV where light does not fall on the screen. • Connect your devices before you position your TV. • Your TV is equipped with a Kensington Security Slot at the back of the TV.
DDNOTE When securing the VESA-compatible wall bracket to your TV, use M4 bolts for 26 inch models, M6 bolts for 32 inch models or M8 bolts for larger models (bolts not supplied). 4.3 Connect the antenna cable 1. Locate the AC IN mains connector at the back or on the bottom of the TV. 2. Connect the mains cord to the AC IN mains connector. 1. Locate the TV ANTENNA connector at the back of the TV. 2. Connect one end of an antenna cable (not supplied) to the TV ANTENNA connector.
EN 1. Slide the battery cover off the back of the remote control. 2. Insert the two supplied batteries (Size AAA, Type LR03). Be sure the + and - ends of the batteries line up with the markings inside the case. 3. Slide the cover back into position. DDNote Remove the batteries if not using the remote control for an extended period of time. 4.6 2. Push the CAM in as far as it will go.
OSD display OSD display Display message Welcome message line 1 Welcome message line 2 Welcome message ti... Enable CI slot Enable teletext Enable MHEG Enable CI slot On Off 4. Press MENU or M to exit.
Remote control overview 1. . Switches the TV on from standby or back to standby. This section provides a detailed overview of remote control features. 2. GUIDE Toggles the Electronic Programme Guide on or off. Only active with digital channels. 1 19 18 17 2 3 4 5 6 7 8 16 15 9 10 14 11 13 12 3. AV Selects connected devices. 4. SUBTITLE Activates or deactivates subtitles. 5. Colour keys Selects tasks, teletext pages. 6. ALARM OFF Deactivates the alarm function.
18. TELETEXT Toggles teletext on or off 19. Spilts the current channel or source on the left of the screen. Teletext appears on the right.
First time setup EN 6 The first time the TV is switched on, a language selection menu appears. Please select your language Press OK or the green colour key on your remote control to continue Select your language and follow the on-screen instructions to setup the TV. EETip You can skip the first time setup procedures by pressing MENU on the TV's control twice.
7 Setup BDS mode Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on The TV is designed to operate as BDS Hotel Mode, which offers the following benefits: • Disable user menu. Guests cannot change channel, picture and sound settings. • Select a switch on volume and channel. The TV will always start on the specified channel and volume level. • Set a maximum volume.
7.3 BDS mode On Off 1. Enter Setup menu. 2. Press ï to select Local keyboard locked. 3. Press Æ to enter Local keyboard locked. 4. Press Î to select On. The VOLUME +/-, PROGRAM +/- and MENU buttons on the TV control are locked. To unlock, select Off. 4. Select Setup menu > Remote control > High security mode. • On Access the BDS Hotel Mode Setup Menu via the setup remote control only. • Off Access the BDS Hotel Mode Setup Menu via the setup remote control or guest mode remote control. 7.
• Off Unlock remote control buttons. • Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on Multi remote control • Off Disable multi remote control function. • Blue Select to use the blue guest remote control. • Red Select to use the red guest remote control. • Green Select to use the green guest remote control. 3. Press Æ to enter OSD display. 4. Press Î or ï to select a setting. 5. Press Æ to enter.
Enable MHEG Select On to access MHEG. • Enable EPG Select On to access EPG. • Enable Subtitles Select On to display subtitles. 7.6 Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume Switch on channel Power on Maximum volume EN • 100 Set switch on volume When the user switches the TV on, it will play at the specified volume level set. 4. Press Î or ï to select the desired volume level. 1. Enter Setup menu. 5.
Setup menu Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on Low power standby Power on On Standby Last status • Green The TV will enter a low standby mode to achieve minimum power consumption. • Fast The TV will enter a semi-standby mode to achieve fast power up. 5. Press ï to select Store - go right and press Æ to save setting. 3. Press Æ to enter Power on. 7.11 Select clock settings 4. Press Î or ï to select the desired status.
• • • Time download Set the time of the clock display automatically via Teletext. The clock will be automatically synchronised to the correct time. Download Program Select the time from the teletext transmission of a channel. Make this download program the same as the startup channel. Time offset Set the time difference between the time received from Teletext to the current time at your location. Buzzer volume Set the volume of the alarm buzzer.
1. Select your desired options or adjustments. Setup menu Power on Low power standby Clock Auto scart USB break-in Monitor out Blank current Channel Store - go right Monitor out On Off 3. Press Æ to enter Monitor out. 4. Press Î or ï to switch ON or OFF this feature. 2. Press ï to select Store - go right. Setup menu Clock Auto scart USB break-in Monitor out Blank current Channel Store - go right Cloning to TV TV to Cloning Store - go right Confirm 3. Press Æ to enter Store - go right. 5.
Clone configuration 8.1 From Cloning to TV Copy TV configuration data from a USB stick to TV. 1. Insert the USB stick to the USB connector at the side of the TV. 2. Enter Setup menu. 3. Press ï to select Cloning to TV. 4. Press Æ to enter Cloning to TV. 5. Press Æ to load data to the TV. During this process, the cloning files.
9 Trouble shooting This section describes commonly-encountered issues and accompanying solutions. 9.1 Communication issues The TV does not communicate with external interactive terminal: • Check that the card slot is enabled. See Section 4.6.2 Access CAM services for details. 9.2 Picture issues No picture • Check that the Blank current channel feature is not switched on. See Section 7.16 Select blank current channel for details. 9.3 Other issues The character 'F' appears on the TV screen.
EN mains cord 10 10 Index A E AUDIO EMF 2 IN 6 EXT 1 6 L/R 6 EXT 2 6 Auto scart 21 EXT 3 6 B G BDS mode Get started 9 setup 16 C H HDMI 7 HDMI 1 6 Channel install manually 19 HDMI 2 6 switch on 19 HDMI 3 6 Clock 7 display on 20 display standby 20 settings 20 time download 21 I Important information 4 K Kensington lock 9 time offset 21 M time setting 20 MHEG 13 Clone configuration Mute 13 from Cloning to TV 23 O From Cloning to TV 23 OSD Common Interface 7 Conditional Access
setup 18 Power indicator 7 low standby 20 on status 19 SPDIF OUT 6 S-VIDEO 6 T Trouble shooting 24 TV 9 R antenna 6 Recycling 5 connection overview 6 Remote control 8 position 9 basic use 8 prepare for digital services 11 batteries 10 setup 15 locked 17 side controls 7 multi 18 stand 9 overview 13 sensor 7 setting 17 smart 18 U USB 7 V VESA 3 S compatible wall bracket 9 Safety 4 SCART 6 VIDEO 6 Volume Screen care 5 buzzer 21 SERV.
© 2008 Koninklijke Philips Electronics N.V. All rights reserved.
