Philips Hospitality TV Installation Manual for 22HFL30x7x/10 26HFL30x7x/10 32HFL30x7x/10 42HFL30x7x/10 Version 1.
Contents 1. Requirements before starting the installation.......................................................................................................... 2 2. Find out the state of the TV ...................................................................................................................................... 3 3. Re-install TV ...........................................................................................................................................................
1. Requirements before starting the installation Before starting the installation, make sure that you have everything you need at hand. Master remote control 22AV8573 or Guest remote control 22AV1108A And USB stick You will need the master remote control or the guest remote control to access the menus. To access the setup menu press the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button. For the guest remote control, press the following keys sequential: 3,1,9,7,5,3, ‘MUTE’.
2. Find out the state of the TV It is important to know if a TV is in ‘virgin mode’ (out of the box) or installed before. If you can see this screen below, you know that the TV is in ‘virgin mode’ and you can install the set. See chapter 4 of this manual. If you power on the set and then press the ‘Home’ button on the guest remote, you will see this screen appear, if the TV already has been installed or the wizard was already skipped.
3. Re-install TV If you want to start an installation from scratch you can always re-install the TV. This can be done by using the option: Re-install TV set. If Professional mode is active you can access the setup menu by pressing the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button (For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’) , then go to TV Setup, confirm with “OK”.
Press “OK” to access the sub-menu, navigate to “Reinstall TV”. Press “OK” to reinstall TV set. If all is correct select “Start now” and press “OK”. After this operation the TV will power off and on and display the installation wizard. Note: All settings are at default values and no channel plan is available.
4. Installation wizard When you turn on the TV for the first time, or you have reinstalled the TV, you should see the following screen. Here you will need to select your preferred language. Please select with Up and Down arrow keys and confirm with ‘OK’ or press the Left arrow key. After this, you will need to select the country. Depending on the country selection, some pre-defined settings will be activated, because of local broadcast requirements.
The next step is to choose between ‘Shop’ and Home’ use. If you select “SHOP” an ‘e-sticker’ banner will be displayed on the TV. This is for commercial purpose only. Now you can select the visual and hearing impaired options. If you select ‘On’, your TV will automatically turn on settings to help visual and hearing impaired people. THE MOST COMMON OPTION IS TO TURN THIS FUNCTION OFF. On the following page we can start the channel installation wizard.
For the channel installations, select ‘Install TV channels’ and press ‘OK’ Then you can select ‘Continue’ and press ‘OK’ again. Here you can select the type of channels you would like to install and what preference you will use.
It is advisable to check the settings before starting the search. The “Frequency scan” contains two options: - “Quick”: this is a fast method to search channels but it might skip some channels (depending on the network). “Full”: the scan will search on all frequencies and will store all channels available. This is the safe method if you don’t know the network parameters, but it takes more time.
The Symbol Rate options are: Automatic and Manual. If you do not know the correct values for this option, please use the Automatic option. Analogue channel: If you don’t have or you don’t want to install analogue channels, you can disable the search for this type of channels. The “Reset” option will reset the search settings to default. After you have checked or changed settings, you can select “Done” and select “Start” to start the channel search.
If you would like to change the picture and sound settings, you can go to “Optimize TV picture and sound” and press the “OK” button on remote control. A wizard will start to guide you through the process of setting the sound and picture on the TV set. Select “Continue” to start the wizard and press the “OK” on remote control. The wizard will ask you some questions about which image you prefer, select the option you desire and press “OK” on the remote control.
After pressing “Done” you have completed the installation of the TV and you should see this screen. Press “OK” on the remote control to exit this wizard. Note: This wizard will not be available anymore when you start the TV the next time. The only way to re-use this wizard is to reinstall the TV set.
5. Channel options a. Reordering channels To reorder TV channels you need the channel plan from the Professional Settings menu. In the consumer menu you cannot rearrange channels. The Professional Settings menu can be accessed by using the Yellow remote (RC 22AV8573 Master Remote control) and pressing the MENU Button or with the TV remote press 3,1,9,7,5,3, MUTE). The Professional Settings menu will appear like in the picture below. Go to the “Channel setup” option and press “OK” to access the submenu.
Select “Reorder” and Press the “OK” button on the remote control to reorder channels. Navigate to the channel that you want to move and press “OK” on the remote control to select that channel. The arrows around the channel indicate that the channel is selected and can be moved. Use the arrow keys to move the channel to the new position. When you have reached the new position press “OK” on the remote control to confirm the new position of the channels.
b. Rename channels Select the channel, press the “Options” button on remote control and select “Rename” to change name of a channel. If you then press the “OK” button a virtual QWERTY keyboard will pop up. c. Hide channels Important: You cannot delete channels from the channel grid, but you can use the option to hide the channels. Select the Channel, press the “Options” button and select “Hide channels”. You will see an “H” in the channel square.
6. Professional Settings [Professional Settings] Settings especially designated for hospitality. [Professional Mode] [Off]: The TV operates as a basic (consumer) TV. [On]: All settings in the Professional Settings Setup menu are active. Only by switching on this mode the TV will act as a Hospitality TV. [Room ID] Entry field to store 4 digits to set the Room Identifier. Room ID can be used to distinguish between different floors/rooms/setups when using SmartInstall.
[USB to TV] Check Cloning section [TV to USB] Check Cloning section [RF to TV] Option used for SmartInstall Note: Setup and configuration for SmartInstall is not covered by this manual [Reset] Reset all settings from Professional mode to default values. [Switch on channel] When the TV is switched on it will start up on the specified source/channel. Available EXT1, EXT2, VGA, HDMI, HDMI side, AV side or one of the installed TV channels.
[Maximum volume] This option specifies the maximum allowable volume level of the TV. Selectable value from 00 until 60. [Switch on picture format] This settings allows you to set a switch on picture format. The power on function allows the TV to enter a specific mode ([On], [Standby], or [Last status]) of operation when the mains power is activated (cold start): [On]: The TV will always turn on (show startup channel) after the mains power is connected.
When pressing “OK” button on remote control while editing line 1 or 2, a virtual keyboard will pop up on screen. Note: Maximum 20 characters per line. [Line 2] Line 2: Second line of the welcome message. [Clear] Will delete the current welcome message. [Message Time-out] Sets the period of time to display the welcome message on the screen when TV is turned on from standby. Selectable values: 20, 25, 30 seconds.
[Info key enable] Enables the possibility to see Hotel Info by pressing the Info button on the remote control. [USB to TV] This option uploads the pictures used for Hotel Info in to the TV. You should only use this when configuring the master TV. You can then clone the settings to another TV. Note: All pictures used for Hotel Info will be cloned. [Local KB lock] [Off]: The local keyboard (controls buttons on the TV) buttons are enabled.
[Auto scart] Enables auto scart switching (or break-in) in Professional mode. [On]: Enables auto scart switching or break-in. [Power On Scart]: Enables auto TV start On/Off when detecting scart break-in. (never use this feature without a connected STB) [Off]: Disables auto scart switching or break-in. [HDMI-CEC in] [Off]: Disables HDMI-CEC feature. [On]: Enables HDMI-CEC feature. Philips EasyLink (HDMI-CEC) enables one-touch play and one-touch standby between HDMI-CEC compliant devices.
[Enable subtitle] Enables or disables the use of subtitles in a DVB broadcast channel: [Off]: No subtitle services available [On]: Subtitle services available [Enable USB] [Off]: Disables USB multimedia function. [On]: Enables USB multimedia functions. Feature is not influencing cloning and/or software upgrade via USB. [Blue mute] [Off]: The background color is set to black in case of no video signal on selected source. [On]: The background color is set to blue in case of no video signal on selected source.
[Download program] To select channel to download clock information. Note: Correct clock information is needed to provide correct EPG data and to have MyChoice working. [Country selection] To select the original country from the channel chosen at “Download program”. [Time offset] To set the time offset. In case the clock download information is not correct for your region you can set an offset here to correct this. Note: Selectable value between -12 and +12.
[Blank channel] The Blank channel function disables the display of video on the TV, but does not affect the audio output. Select or deselect can be done by pressing “OK” button on the remote control. Note: The channels marked with X will not display video on the TV. [Auto channel update] [ON]: Enables automatic channel update. [OFF]: Disables automatic channel update.
[ThemeTV] [OFF]: Disables ThemeTV [ON]: Enables ThemeTV [Startup]: Will show the ThemeTV screen at startup MyChoice configuration: R0 – Ring 0 (All channels) R1 – Ring 1 (Free to view channels) Note: MyChoice setup is not included in this manual. ThemeTV Configuration: Edit the names for ThemeTV categories Note: ThemeTV setup is not included in this manual To select the TV channels for every ThemeTV category.
7. Welcome Logo There are 2 Philips logos displayed at startup. Second logo can be replaced by picture uploaded via USB. File format: 1280 x 720.png file. Note: below timing values are approximate indications and can differ from real situation! How to upload Welcome Logo 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Create graphics file: 1280 x 720 .png with logo. File name: T911HE_WelcomeLogo.
8. Clone With cloning it is possible to copy to/from a USB device TV the configuration data and the channel list data. Place a USB Memory stick in the USB side connector of the TV. *USB device should be formatted as FAT or FAT32. Access the Professional menu by pressing the ‘RC5 SETUP’ key, and then press the ‘Home/Menu’ button.(For the guest remote control, press the following keys in sequence: 3,1,9,7,5,3, ‘MUTE’). Access the Professional settings and go to: [USB to TV] 1. Select [USB to TV] and press OK.
9. Feature settings [Multi RC] This function allows that up to four televisions can be installed in a room whereas every TV will listen to its own RC. Once the TV is set, also every RC can be set to remember its connected TV: [Off] This function is not used; all TVs will listen to a ‘blue’ RC. [Blue] The TV will listen to a ‘blue’ RC. Press and hold both the menu and blue button on the RC for about five seconds. [Green] The TV will listen to a ‘green’ RC.
10. CSM (Consumer Setup menu) The CSM contains data about the TV software, serial number and other details. The menu can be accessed using a standard remote control or using the master remote control. 1. Using the standard remote control: press the following key sequence “1,2,3,6,5,4” 2. Using master remote control (22AV8753D): Press the RECALL button, available only if PBS mode is ON. Notes: Activation of the CSM is only possible if there is no (user) menu on the screen.
