S line 223S7/243S7 www.philips.
Table of Contents 1. Important �������������������������������������� 1 1.1 Safety precautions and maintenance ��������������������������������� 1 1.2 Notational Descriptions ������������ 3 1.3 Disposal of product and packing material ������������������������������������������ 4 2. Setting up the monitor �������������� 5 2.1 Installation ������������������������������������ 5 2.2 Operating the monitor ���������������7 2.3 Remove the Base Assembly for VESA Mounting ��������������������������10 2.
1. Important • Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor’s electronics. • Do not block the ventilation holes on the cabinet. • When positioning the monitor, make sure the power plug and outlet are easily accessible. • If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation.
1. Important be better than a 15-minute break every two hours. Try to keep your eyes from eye strain while using the screen for a constant period of time by : not expose the monitor to dust, rain, water, or excessive moisture environment. • If your monitor gets wet, wipe it with dry cloth as soon as possible. • If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord.
1. Important Warning Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “afterimage” or “ghost image” symptoms that will not disappear and cannot be repaired. The damage mentioned above is not covered under your warranty. 1.2 Notational Descriptions The following subsections describe notational conventions used in this document.
1. Important Taking back/Recycling Information for Customers 1.3 Disposal of product and packing material Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. Waste Electrical and Electronic Equipment-WEEE From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
2. Setting up the monitor Install the base 2. Setting up the monitor 1. 2.1 Installation Place the monitor face down on a smooth surface. Pay attention not to scratch or damage the screen. Package contents S line 223S7/243S7 278E9 Quick Start Register your product and get support at www.philips.com/welcome 2. Hold the stand with both hands. (1) Gently attach the stand to the VESA mount area. Monitor User’s Manual 使用 前请阅读使用说明 Contents: User’s Manual Drivers 2 01 9 a.
2.
2. Setting up the monitor 243S7EJMB： 2.2 Operating the monitor Description of the control buttons 9 1 8 7 6 5 4 3 2 3 1 Kensington anti-theft lock 2 Earphone jack 7 6 5 4 2 1 3 Audio input 4 VGA input Switch monitor’s power ON and OFF. 5 HDMI input 7 USB upstream Access the OSD menu. Confirm the OSD adjustment. 8 USB downstream Adjust the OSD menu. 9 AC power input Adjust the speaker volume. 6 DisplayPort input Connect to PC Change the signal input source. 1.
2. Setting up the monitor Description of the On Screen Display Main menu LowBlue Mode What is On-Screen Display (OSD)? On 1, 2, 3 Off Input On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below: Sub menu VGA HDMI (2X3S7EHMB) HDMI 1.
2. Setting up the monitor Height adjustment Resolution notification This monitor is designed for optimal performance at its native resolution, 1920 × 1080 @ 60 Hz. When the monitor is powered on at a different resolution, an alert is displayed on screen: Use 1920 × 1080 @ 60 Hz for best results. Display of the native resolution alert can be switched off from Setup in the OSD (On Screen Display) menu.
2. Setting up the monitor Note This monitor accepts a 100mm x 100mm VESA-Compliant mounting interface. VESA Mounting Screw M4. Always contact manufacturer for wall-mount installation. 2.3 Remove the Base Assembly for VESA Mounting Before you start disassembling the monitor base, please follow the instructions below to avoid any possible damage or injury. 1. Extend the monitor base to its maximum height. 100mm 100mm 2. Place the monitor face down on a smooth surface.
2. Setting up the monitor 2.4 SoftBlue Technology introduction SoftBlue LED technology uses a smart technology to reduce harmful shortwave blue light without affecting the color or image of the display. SoftBlue LED technology is certified by international testing organizations TUV Rheinland to reduce harmful blue light. Note SoftBlue is compliance with TUV ABL certification when LBL is under the off mode and color temperature is default mode.
3. Image Optimization 3. Image Optimization 1. Press to launch the SmartImage on screen display. 3.1 SmartImage 2. Keep pressing to toggle among EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode and Off. What is it? 3. The SmartImage on screen display will remain on screen for 5 seconds, or you can also press "OK" to make confirmation. There are multiple selections: EasyRead, Office, Photo, Movie, Game, Economy, LowBlue Mode and Off.
3. Image Optimization • • Photo: This profile combines color saturation, dynamic contrast and sharpness enhancement to display photos and other images with outstanding clarity in vibrant colors - all without artifacts and faded colors. 3.
4.Technical Specifications 4. Technical Specifications Picture/Display Monitor Panel Type Backlight Panel Size Aspect Ratio Pixel Pitch Contrast Ratio (typ.
4.Technical Specifications Stand Tilt Swivel Height adjustment Pivot -5 / +25 degree -175 / +175 degree 130mm 90 degree Power (223S7EHMB) Consumption Normal Operation Sleep (Standby) Off Heat Dissipation* Normal Operation Sleep (Standby) Off On Mode(ECO mode) Power LED indicator Power Supply AC Input AC Input AC Input Voltage at Voltage at Voltage at 100VAC , 60Hz 115VAC , 60Hz 230VAC, 50Hz 20.6 W (typ.) 20.5 W (typ.) 20.2 W (typ.) <0.5W <0.5W <0.5W <0.3W <0.3W <0.
4.Technical Specifications Power (223S7EJMB) Consumption Normal Operation Sleep (Standby) Off Heat Dissipation* Normal Operation Sleep (Standby) Off On Mode(ECO mode) Power LED indicator Power Supply AC Input AC Input AC Input Voltage at Voltage at Voltage at 100VAC , 60Hz 115VAC , 60Hz 230VAC, 50Hz 21.3 W (typ.) 20.7 W (typ.) 21.52 W (typ.) <0.5W <0.5W <0.5W <0.3W <0.3W <0.3W AC Input AC Input AC Input Voltage at Voltage at Voltage at 100VAC , 60Hz 115VAC , 60Hz 230VAC , 50Hz 72.7 BTU/hr 70.65 BTU/hr 73.
4.Technical Specifications Heat Dissipation* Normal Operation Sleep (Standby) Off On Mode(ECO mode) Power LED indicator Power Supply AC Input AC Input AC Input Voltage at Voltage at Voltage at 100VAC , 60Hz 115VAC , 60Hz 230VAC , 50Hz 76.79 BTU/hr 75.09 BTU/hr 74.4 BTU/hr (typ.) (typ.) (typ.) <1.71 BTU/hr <1.71 BTU/hr <1.71 BTU/hr <1.02 BTU/hr <1.02 BTU/hr <1.02 BTU/hr 10.5 W (typ.
4.Technical Specifications Product without stand Product with packaging Operating Condition Temperature range (operation) Relative humidity (operation) Atmospheric pressure (operation) Temperature range (Non-operation) Relative humidity (Non-operation) Atmospheric pressure (Non-operation) Environmental and energy ROHS Packaging Specific Substances Cabinet Color Finish 2.63 kg(223S7EYMB/223S7EHMB) 2.77 kg(223S7EJMB) 3.10 kg(243S7EYMB/243S7EHMB) 3.20 kg(243S7EJMB) 6.56 kg(223S7EYMB/223S7EHMB) 6.
4.Technical Specifications 4.1 Resolution & Preset Modes Maximum Resolution 1920 x 1080 @ 60 Hz (analog input) 1920 x 1080 @ 60 Hz (digital input) Recommended Resolution 1920 x 1080 @ 60 Hz (digital input) H. freq (kHz) Resolution V. freq (Hz) 31.47 720 x 400 70.09 31.47 640 x 480 59.94 35.00 640 x 480 66.67 37.86 640 x 480 72.81 37.50 640 x 480 75.00 35.16 800 x 600 56.25 37.88 800 x 600 60.32 46.88 800 x 600 75.00 48.08 800 x 600 72.19 47.73 832 x 624 74.55 48.
5.Power Management 223S7EJMB 5. Power Management Power Management Definition If you have VESA DPM compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. If an input from a keyboard, mouse or other input device is detected, the monitor will 'wake up' automatically.
5.Power Management 243S7EJMB Power Management Definition VESA Mode Video H-sync V-sync Power Used LED Color Active ON Yes Yes 22.8W (typ.) White 45W (max.) Sleep (Standby) OFF No No 0.5W (typ.) White (blink) Off OFF - - 0.3W (typ.) OFF The following setup is used to measure power consumption on this monitor. • Native resolution: 1920 × 1080 • Contrast: 50% • Brightness: 100% • Color temperature: 6500k with full white pattern Note This data is subject to change without notice.
6.Customer care and warranty of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. 6. Customer care and warranty 6.
6.Customer care and warranty Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Three adjacent lit sub pixels (one white pixel). Note A red or blue bright dot must be more than 50 percent brighter than neighboring dots while a green bright dot is 30 percent brighter than neighboring dots.
6.Customer care and warranty Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT Monitor panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables.
6.Customer care and warranty 6.2 Customer Care & Warranty For warranty coverage information and additional support requirements valid for your region, please visit www.philips.com/support website for details or contact your local Philips Customer Care Center. For extended warranty, if you would like to extend your general warranty period, an Out of Warranty service package is offered via our Certified Service Center. For Warranty Period please refer to Warranty Statement in Important Information Manual.
7.Troubleshooting & FAQs 7. Troubleshooting & FAQs • Check to see if the monitor cable has bent pins. • Make sure the computer is turned on. 7.1 Troubleshooting AUTO button doesn't function • This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. The auto function is applicable only in VGA-Analog mode.
7.Troubleshooting & FAQs Main Controls. It is valid only in VGA mode. and cannot be repaired. The damage mentioned above is not covered under your warranty. Horizontal flicker appears Image appears distorted. Text is fuzzy or blurred. • • Adjust the image using the “Auto” function in OSD Main Controls. • Eliminate the vertical bars using the Phase/Clock of Setup in OSD Main Controls. It is valid only in VGA mode.
7.Troubleshooting & FAQs you for monitor drivers (.inf and .icm files) or a driver disk when you first install your monitor. Follow the instructions to insert the companion CD-ROM included in this package. Monitor drivers (.inf and .icm files) will be installed automatically. 7.2 General FAQs Q1: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? Ans.: Recommended resolution for this monitor: 1920 x 1080 @ 60 Hz.
7.Troubleshooting & FAQs Ans.: Yes, you can change your color setting through OSD control as the following procedures, • Press "OK" to show the OSD (On Screen Display) menu • Press "Down Arrow" to select the option "Color" then press "OK" to enter color setting, there are three settings as below. 1. Color Temperature: The six settings are 5000K, 6500K, 7500K, 8200K, 9300K and 11500K.
7.Troubleshooting & FAQs Q12: Why is my Display not showing sharp text, and is displaying jagged characters? Ans.: Your LCD monitor works best at its native resolution of 1920 x 1080 @ 60 Hz. For best display, please use this resolution. Q13: How to unlock/lock my hot key? Ans.: Please press for 10 seconds to unlock/lock the hot key, by doing so, your monitor pops out “Attention” to show the unlock/lock status as shown below illustrators.
2019 © TOP Victory Investment Ltd. All rights reserved. This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. Specifications are subject to change without notice.
