Specifications

41
TPF1.3A LA
8. Alignments
8. Alignments
index of this chapter:
8.1 Electrical Instructions
8.2 DDC Instructions&Serial NO. Definition
8.3 DDC DATA
8.4 ISP Instructions
8.5 Display Adjustment
8.1 Electrical Instructions
1. General points
1.1 During the test and measuring, supply a distortion free AC mains
Voltage to the apparatus via an isolated transformer with low
internal resistance.
1.2 All measurements mentioned hereafter are carried out at a normal
mains voltage (90 - 132 VAC for USA version, 195 -264 VAC for
EUROPEAN version, or 90 - 264 VAC for the model with full range
power supply, unless otherwise stated.)
1.3 All voltages are to be measurement or applied with respect to
ground,unless otherwise stated.
Note: Don‘t use heat-sink as ground.
1.4 The test has to be done on a complete set including LCD panel
in a room with temperature of 25 +/- 5 degree C.
1.5 All values mentioned in these test instruction are only applicable
of a well aligned apparatus, with correct signal.
1.6 The letters symbols (B) and (S) placed behind the test instruction
denotes
(B): carried out 100% inspection at assembly line
(S): carried out test by sampling
1.7 The white balance (color temperature), has to be tested in subdued
Lighted room.
1.8 Repetitive power on/off cycle are allowed except it should be avoided
within 6 sec.
2. Input signal
---------------
2.1.1 PC Signal type
Analog Video : 0.7 Vp-p linear, positive polarity
Separate Sync. : TTL level, separate, positive or negative polarity
Audio signal : Mini-jack audio input
Input level: 500 mVrms (Speaker outpout 3W when Input level
> 630mVrms and Volume control at 100%)
TV Signal type
RF Signal : Aerial input, NTSC cable and antenna system.
Video signal : Cinch input, CVBS with NTSC and PAL system.
Level: 1.0Vp-p (0.7V video + 0.3V sync.)
S video input: Y/C signal, NTSC and PAL system.
Level: Y: 1.0Vp-p (0.7V video + 0.3V sync.)
C: +/- 0.3V.
Component input: Cinch G/B/R-> YPbPr cinch input.
Level: Y: 1.0Vp-p Pb/Pr: +/- 0.35V
Audio signal : Side cinch R/L for CVBS and S-video
Bottom cinch R/L for component input.
Input level: 500 mVrms (Speaker outpout 3W when Input level
> 630mVrms and Volume control at 100%)
2.2 PC Input signal mode
PRE-LOAD VIDEO RESOLUTION
Mode 3, 6, 7 are preset modes that should pass QA inspection.
Mode 1, 2, 4, 5, 8 will run auto adjustment only, and W/O QA
checking.
Dot rate (MHz) H.freq
(KHz)
Mode Resolution V.freq (Hz)
1 25.175 31.469 IBM VGA 640 * 350 70.087
2 28.322 31.469 IBM VGA 720 * 400 70.087
3 25.175 31.469 IBM VGA 640 * 480 59.940
4 30.240 35.000 MACINTOSH 640 * 480 66.667
5 31.500 37.500 VESA 640 * 480 75.000
6 36.000 35.156 VESA 800 * 600 56.250
7 40.000 37.879 VESA 800 * 600 60.317
8 49.500 46.875 VESA 800 * 600 75.000
2.3 TV input signal Channel and pattern for China model (1)
Signal Distribution Table (PAL D)
Frequency Carriers
PRG CH
Video Sound
TV System
Pattern
1
C4 65.25MHz 71.75MHz
PAL D
(CCIR)
Full Write
2
E7 184.25MHz 190.75MHz
PAL D
(CCIR)
Circle
Pattern
3
E12 224.25MHz 230.75MHz
PAL D
(CCIR)
Color Bar
4
K21 471.25MHz 477.75MHz
PAL D
(CCIR)
Full Write
5
G34 511.25MHz 517.75MHz
PAL D
(CCIR)
Circle
Pattern
6
G62 547.25MHz 553.75MHz
PAL D
(CCIR)
Color Bar
7
M58 551.25MHz 557.75MHz
PAL D
(CCIR)
Crosshatch
8
G47 615.25MHz 621.75MHz
PAL D
(CCIR)
Color Bar
Table 1
[url=http://www.hqjdw.com/register.php?fromuser=乖乖狗]
红旗家电维修论坛，游客都可以下载资料[/url]
乖乖狗制作，严禁转载
http://www.hqjdw.com/?fromuid=乖乖狗