electronic user's manual file:///D|/EDFU/crt_19_6/edoc/english/202P/manual.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
About This Electronic User's Manual About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips Color Monitor. It describes the monitor's features, setup, operation and all other information, which is the same exact information described in our printed version.
About This Electronic User's Manual RETURN TO TOP OF THE PAGE Notational Descriptions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system.
About This Electronic User's Manual ©2005 Koninklijke Philips Electronics N.V. All rights reserved. Reproduction, copying, usage, modifying, hiring, renting, public performance, transmission and/or broadcasting in whole or in part is prohibited without written consent of Philips Electronics N.V. file:///D|/EDFU/crt_19_6/edoc/english/202P/ABOUT/ABOUT.
202P Product Information Product Information Product Features • Lead-free product • Technical Specifications • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features Model Regulation Color 202P70 TCO'03 Gray 202P73 TCO'03 Silver/Black 202P75 TCO'99 Black 202P7: ● ● ● ● ● ● ● 22-inch (20.
202P Product Information Technical Specifications* CRT • Size and deflection • Dot pitch / Grille pitch 22 inch / 55 cm ; 90° deflection angle 0.25 mm • Horizontal pitch • Tube type Flat shadow mask, spin coating, TCO, anti-static • Phosphor P22 • Recommended display area 15.4" x 11.6" / 392 x 294 mm • Maximum display area 16.0" x 12.
202P Product Information sRGB sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.) Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.
202P Product Information Active ON Yes Yes Typical 125 W 0% Green Sleep OFF No No < 1W 99 % Yellow Switch Off OFF -- -- < 1W 99 % Off This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimensions 19.7" x 19.7" x 18.7" / 501 x 502 x 476 mm (including base) 19.7" x 18.0" x 18.
202P Product Information The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. Assignment Pin No. Assignment 1 Red video input 9 +5V (PC) 2 Green video input&SOG 10 Sync ground 3 Blue video input 11 Identical output - connected to pin 10 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 Not connected 13 H. Sync / H+V 6 Red video ground 14 V.
202P Product Information file:///D|/EDFU/crt_19_6/edoc/english/202P/PRODUCT/PRODUCT.
Installing your Monitor Installing your Monitor Front View • Rear View Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls file:///D|/EDFU/crt_19_6/edoc/english/install_4/install.
Installing your Monitor Contrast hotkey. When the UP arrow is pressed, the adjustment controls for the CONTRAST will show up. UP and DOWN buttons are used when adjusting the OSD of your monitor Brightness hotkey. When the RIGHT arrow is pressed ,the adjustment controls for BRIGHTNESS will show up. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. By pressing both the UP and OK buttons, you can easily access the Input Signals A and/or B.
Installing your Monitor 1. D-Sub Port - Attach the D-Sub connector that comes with your monitor here. Other end connects to your PC. 2. Power in - Attach power cable here. file:///D|/EDFU/crt_19_6/edoc/english/install_4/install.
Installing your Monitor 3. BNC Connectors - Attach the connectors here to get the best video performance from your monitor. RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19_6/edoc/english/install_4/install.
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. Your monitor may not include all the items in the OSD tree shown below. file:///D|/EDFU/crt_19_6/edoc/english/osd/OSDDESC.
On-Screen Display file:///D|/EDFU/crt_19_6/edoc/english/osd/OSDDESC.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19_6/edoc/english/osd/OSDDESC.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO READ THE WARRANTY COVERED: WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey • Bulgaria • Slovakia • Slovenia LATIN AMERICA: Antilles • Argentina • Brazil • Chile • Colombia • Mexico • Paraguay • Pe
Frequently Asked Questions Frequently Asked Questions 1. What does the "Designed for Windows" logo signify? The "Designed for Windows" logo means your Philips monitor fulfills the requirements and recommendations of the PC9x (97, 98, or 99) System Design Guide and passes stringent WHQL tests. 2. What is USB? Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals.
Frequently Asked Questions 6. What models are Mac compatible? All listed Philips monitors are Mac compatible. BUT, you may need an adapter to connect the monitor to your Mac system. Please contact your dealer/reseller for details. 7. What is TCO? TCO is a Swedish abbreviation for the Swedish Confederation of Professional Employees. 8. What is MPR? MPR is a Swedish abbreviation for the Swedish National Board of Measurement and Testing. 9.
Frequently Asked Questions TCO95: Further toughened TCO92 rules. TCO99: Delineated even more severe standards and test procedures than TCO95. TCO'03: Same as TCO99 standard + Testing uncertainty. Safety: MPRII: No requirement. TCO92/95/99/03: All set requirements. Energy Saving: MPRII: No requirement. TCO92: Standby mode < 30W, Off mode < 8W TCO95: Standby mode < 30W, Off mode < 8W TCO99: Standby mode < 15W, Off mode < 5W TCO'03:Standby mode < 15W, Off mode < 5W Visual Ergonomics: MPRII: No requirement.
Frequently Asked Questions 10. How do I enable the energy saving function? Go to 'My Computer' and select 'Control Panel' followed by 'Monitor Control.' Select "All default selection' and choose your Philips monitor model from the default driver list. Plug and Play will automatically enable the EPA tick box for you. In DOS or Windows 3.1, you must first make sure your PC supports power saving. 11.
Frequently Asked Questions Available resolutions are determined by the capabilities of your video card and graphic driver. Under Windows '95, you may select the desired available resolution through the 'Display properties/Settings' menu. 14. How can I adjust the size, position and rotation of my screen? Depending on the model you own, you can use your CustoMax Software, On Screen Display (OSD) or control knobs located on the monitor. 15.
Frequently Asked Questions LightFrame consists of a software application and an Integrated Circuit (IC) embedded in the monitor. Together, they boost brightness and sharpness in a user defined window or screen area. Unique LightFrameTM technology dramatically improves photo and video display quality. 18. Why is LightFrame important to me? With LightFrame , selected Philips monitors deliver TV quality video and photo display while maintaining monitor performance for text-based applications.
Frequently Asked Questions 21. I get a message warning that my monitor 'may not support LightFrame certain my monitor does. What is wrong? '. I am Only a Philips driver can determine if your monitor is equipped with LightFrame ; a generic Windows driver cannot. Install the special Philips driver that came with your monitor. If the warning continues to flash after your Philips driver is installed, ignore the message. LightFrameTM will function properly. 22.
Frequently Asked Questions 24. How did Philips achieve XtraSpace Design? Philips achieved this breakthrough in reduced footprint CRT display devices through short depth tubes and a focused design process that squeezed every excess millimeter out of XSD monitor desk space requirements. 25. What is Philips monitors' solution for audio? Not all users need multimedia capabilities. To give users freedom of choice, Philips provides an optional Multimedia Base (type number: 6G3B10).
Frequently Asked Questions The major advantage of the Multimedia Base is its minimal space requirements. In fact, it hardly uses any extra space at all: monitor depth and width are unchanged. Only the monitor's height is increased by only 3 centimeters. 29. Where can I buy a multimedia base to incorporate with my Philips monitor? Please contact your dealer/reseller for details. 30. What does Auto Calibrate do? It makes your monitor perform better and last longer.
Frequently Asked Questions During the calibration process, different predefined black and white images are displayed on thescreen. The beam currents of the red, green and blue cannon are accurately measured and compared to the original values stored in the monitor. By readjusting gain values of the individual cannons, deviation is reduced to zero. Default values are stored during production. If the user sets a new color temperature, this new value is saved as the new default value. 33.
Frequently Asked Questions Check the following for possible solutions: ● ● ● ● ● Bent pins on the video cable Make sure the computer is turned on Ensure the VGA Cable is properly connected Ensure the BNC/D-Sub connector on the rear of the monitor is in the correct position, newer models have this option in the On Screen Display under Input Signal Selection. Video card may be not a VESA standard (try the monitor with another computer) 37.
Frequently Asked Questions 40. My monitor appears to be missing one or more colors. How do I correct this? ● ● ● ● If the OSD menu is also missing a color, please contact service for details Set color temperature to 9300 color coordination Check the video cable for any bent pins Video card could be defective (try the monitor with another computer). 41. When I degauss my monitor, it makes a loud noise.
Frequently Asked Questions 43. The edge of the picture on the screen appears to be distorted. How can I correct this? Please perform the following to correct the picture image: ● ● ● ● A magnetic or electrical interference typically causes poor geometry in the picture.
Frequently Asked Questions This phenomenon can occur with Philips 107P, 109P and 201P monitors and is normal. Your monitor is using an Aperture Grille, which consists of fine vertical wires to align the electron beams with the phosphors on the screen. To prevent these vertical wires from vibrating and to keep them properly aligned with the picture tube, two horizontal damper wires are required. These are located on one-third and on two-third from the top of the screen.
Frequently Asked Questions 49. Why is there no picture on my monitor even though the power LED is green? ● Verify the Contrast and Brightness setting of the monitor. First press and hold the 5 (-) button to increase Contrast and then press and hold the 4 (+) button to increase Brightness. These buttons are located on the front of your monitor. ● ● Press both the 5(-) button and the OK button at the same time to switch input A|B. Try and repeat step 48 above. 50.
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ A Autoscan A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal and vertical frequencies of input signals with those of the installed video card. An autoscan monitor can thus operate with a wide range of video cards. MultiSync, a registered trademark of NEC, provides a similar function.
Glossary RETURN TO TOP OF THE PAGE C CE Mark CE mark is displayed on products per EMC and LV ( low Voltage Device ) directives in compliance with European Community safety, EMI and EMS requirements and is compulsory on products for sale in the European Community. Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source.
Glossary a picture is set by the brightness of the unexcited phosphor, which is governed by the degree with which ambient light is reflected. Contrast is therefore reduced in conditions of high ambient light levels. Black Matrix tubes reflect less ambient light so exhibit higher contrast than other tubes. Convergence error Bean misalignment causing one or more of the three beams passing through the wrong aperture in the shadow mask and striking a phosphor dot in the wrong triad.
Glossary Cathode-ray tube - the general term for all tubes in which one or more electron beams emitted by a cathode are periodically scanned across a phosphor screen by means of deflection circuitry. A special form of the cathode-ray tube is the TV and monitor picture tube. RETURN TO TOP OF THE PAGE D DDC (Display Data Channel) DDC is a communication channel for displays and computers.
Glossary DDC 1/2B See DDC. DDC 2Bi See DDC. Degaussing The procedure of demagnetizing the shadow mask and associated metal parts of a picture tube at switch-on to minimize picture distortion. This is usually accomplished by means of a special degaussing coil through which a decaying alternating current is passed to generate an alternating magnetic field that gradually decays to demagnetize the tube. Some monitors offer a manual degaussing facility that can be activated at any time.
Glossary Dot rate Frequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between the video card and subsequent processing circuitry. Also known as video dot rate. RETURN TO TOP OF THE PAGE E Electromagnetic radiation standards International standards set to limit electromagnetic emissions from monitors. There are currently file:///D|/EDFU/crt_19_6/edoc/english/GLOSSARY/GLOSSARY.
Glossary two important standards both derived from regulations originally laid down by Swedish authorities. MPR-II The standard originally proposed by the Swedish National Board of Measurement and Testing. It set maximum levels of electromagnetic radiation emitted by monitors, and has now been adopted as a world standard. MPR-II defines maximum permitted electrostatic, magnetic and electric field levels measured at a distance of 50 cm from the center of the monitor (see table).
Glossary problem can, however, be eliminated by increasing the refresh rate (number of frames/second) of the monitor to a value above around 70 Hz. Sensitivity to flicker appears to diminish with increasing age. RETURN TO TOP OF THE PAGE H Hertz The unit of frequency named after the physicist Heinrich Hertz (1857-1894). 1 hertz (Hz) is equal to 1 cycle/second. Horizontal dot pitch See Dot pitch.
Glossary INF file (Information File) Information (INF) files store information in a specific format. The set-up functions retrieve information from the INF file to use when performing installation operations. Examples of the type of information stored in an INF file include INI and registry changes, file names, and locations of the source files on source media. Interlaced/non-interlaced Interlaced.
Glossary L Linearity The degree to measure the actual location of a pixel on the screen corresponds with its intended location. ( see figure ) Line frequency See Horizontal scanning frequency. Low-emission monitor A monitor that complies with international standards on radiation. See Electromagnetic radiation standards. Low-frequency electric and magnetic fields file:///D|/EDFU/crt_19_6/edoc/english/GLOSSARY/GLOSSARY.
Glossary Alternating fields generated by the deflection yoke. These are subject to increasing attention, notably by governing authorities, the trade and the press. Although there is no scientific evidence that monitor emissions are harmful, much effort has gone into reducing emissions on the principle of better safe than sorry.
Glossary N Non-interlaced See Interlaced/non-interlaced. RETURN TO TOP OF THE PAGE O OSD (On Screen Display) The feature that allows an end user to adjust screen performance and parameters of monitors directly through an on-screen instruction window. See CustoMax in CrystalClear section. Overscan The practice in which areas without useful video information are scanned outside the visible screen area in order to make maximum use of the screen for display of active video information.
Glossary Parallelogram Distortion See Geometric distortion. Phosphor Generic name for the class of substances that exhibit luminescence. To produce a picture on screen, phosphors are deposited on the inner surface of the picture-tube screen and excited into luminescence by the electron beam. Typical examples of phosphors are P22 medium shortpersistence phosphor and EBU high-color-saturation phosphor. Pin-cushion Distortion See Geometric distortion.
Glossary Plug-and-Play See DDC. See USB section. RETURN TO TOP OF THE PAGE R Raster The area on screen that electron beam can reach. Refresh rate See Vertical scanning frequency. Resolution The number of pixels that can be displayed on the screen. The resolution is specified as the number of pixels in a line multiplied by the number of horizontal lines. See also video graphic adapter. Rotation function The feature that allows users to adjust the whole screen rotating to be horizontal.
Glossary S Screen coatings Anti-Static coatings Due to bombardment by beam electrons, monitor screens become electrically charged when in use. Electrically charged screens surfaces can attract dust particles. An Anti-Static coating is a conductive coating deposited on the screen (or on a glass panel immediately in front of the screen) that conducts away the charge and prevents screen dust build-up.
Glossary ARAS is one of the most effective anti-reflection/anti-static screen treatments currently available. It is composed of a multi-layer structure of transparent dielectric material that suppresses specular reflections by broadband interference effects at the screen surface. Anti-static properties are provided by a single conductive layer within the multi-layer structure. With ARAS, the intensity of reflected light is reduced from around 4.
Glossary common: SOG (Synchronization On Green) A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse, red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitor using one of three methods: 1. Separate sync: Horizontal and Vertical sync signals transmitted separately 2. Composite sync: Horizontal and vertical sync pulses mixed into a single signal train. 3.
Glossary T TCO See Electromagnetic radiation standards. Tilt function See rotation function. Trapezoid distortion See Geometrical distortion. TTL signal A TTL (Transistor-transistor-logic) signal is a digital signal level for controlling the screen colors. With TTL driving, the red, green and blue signals can only be switched on or off or provided with an intensity signal. A TTL-driven monitor can thus display a maximum of 64 colors. Video standards such as MDA, CGA and EGA are based on TTL level.
Glossary ● ● ● USB eliminates "case angst" -- the fear of removing the computer case to install add-on peripherals. And USB also eliminates adjustment of complicated IRQ settings when installing new peripherals. USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera, for example) and a joystick.
Glossary for example, a data/FAX modem device. Devices may be physical, electrical, addressable, and logical. Downstream The direction of data flow from the host or away from the host. A downstream port is the port on a hub electrically farthest from the host that generates downstream data traffic from the hub. Downstream ports receive upstream data traffic. Upstream The direction of data flow towards the host.
Glossary V Vertical dot pitch See Dot pitch. Vertical scanning frequency Expressed in Hz, this is the number of fields written to the screen every second in interlaced mode. In non-interlaced mode vertical scanning frequency is the number of frames (complete pictures) written to the screen every second (also known as refresh rate). Vertical sync pulses A train of square shaped waveforms that define the start of a new frame.
Glossary A card equipped with a character or graphic generator and video memory, which maps to the screen. A microprocessor scans video memory and translates bit information from the computer into displayable video signals for the monitor. These cards comply with various standards that determine the nature and quality of the display. VGA (Video Graphics Array), introduced in 1987, was the first analog card.
Download and Print Download and Print This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Mac. Download instructions: To download the file: 1. Click-and-hold your mouse over the icon below. (Win95/98 users right-click) 2.
Download and Print file:///D|/EDFU/crt_19_6/edoc/english/DOWNLOAD/DOWNLOAD.
Troubleshooting Troubleshooting Safety Precautions and Maintenance • Troubleshooting • Regulatory Information• Other Related Information Common Problems Having trouble? Something not working? Before calling for help, try these suggestions.
Troubleshooting No color or intermittent color ● ● ● Color appears blotchy ● ● Missing one or more colors ● ● ● Dim Picture Picture is too large or too small. Edges of the picture are not square. ● Unstable Picture Problem with On Screen Display Check the Color Temperature. Make sure the monitor cable is properly connected to your computer. Check to see if the monitor cable has bent pins. Adjust the Brightness and Contrast controls.
Troubleshooting For further assistance, refer to the Consumer Information Centers list to contact your local Philips distributor. RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19_6/edoc/english/202P/SAFETY/saf_troub.
Regulatory Information Regulatory Information TCO'99 Information • TCO'99 Environmental Requirements • TCO'03 Information • Recycling Information for Customers • Waste Electrical and Electronic Equipment-WEEE • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information What does labeling involve? This product meets the requirements for the TCO' 99 scheme which provides for international and environmental labeling of personal computers. The labeling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration).
Regulatory Information Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Regulatory Information TCO' 03 Information (For TCO Model Only) Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO'03 Display requirements.
Regulatory Information ● environmental management system such as EMAS or ISO 14 000 Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction.
Regulatory Information Philips Electronics Industries (Taiwan) Ltd, Monitor Business Unit E-mail: job.chiu@philips.com Tel: +886 (0) 3 454 9839 Mr. Maarten ten Houten - Senior Environmental Consultant Philips Consumer Electronics E-mail: marten.ten.houten@philips.com Tel: +31 (0) 40 27 33402 Ms. Delmer F. Teglas Philips Electronics North America E-mail: butch.teglas@philips.
Regulatory Information following provisions of directives applicable - 73/23/EEC (Low Voltage Directive) - 89/336/EEC (EMC Directive) - 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level.
Regulatory Information As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. We recommend you switch off the monitor when it is not in use for quite a long time. RETURN TO TOP OF THE PAGE Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Regulatory Information RETURN TO TOP OF THE PAGE Commission Federale de la Communication (FCC Declaration) Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une installation résidentielle.
Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information RETURN TO TOP OF THE PAGE North Europe Information (Nordic Countries) Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. file:///D|/EDFU/crt_19_6/edoc/english/202P/SAFETY/regs/regulat.
Regulatory Information Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Regulatory Information Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspricht, ist darauf zu achten, daß 1. Reparaturen nur durch Fachpersonal durchgeführt werden. 2. nur original-Ersatzteile verwendet werden. 3. bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird. Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge).
Regulatory Information WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.
Regulatory Information 2. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. 3. The BROWN wire must be connected to the terminal which marked with the letter "L" or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires. RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19_6/edoc/english/202P/SAFETY/regs/regulat.
Other Related Information Other Related Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
The OSD Controls The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Contrast (HotKey) • Language • Input Signal Selection • Zoom • Adjust Horizontal • Adjust Vertical • Adjust Shape • Adjust Color • Reset to Factory Settings • Extra Controls • Close Main Controls BRIGHTNESS To adjust your screen's brightness, follow the steps below. Brightness is the overall intensity of the light coming from the screen. A 50% brightness is recommended.
The OSD Controls RETURN TO TOP OF THE PAGE CONTRAST To adjust your screen's contrast, follow the steps bellow. Contrast is the difference between the light and dark areas on the screen. A 100% contrast is recommended. 1) Press the or button on the monitor. The CONTRAST window appears. 2) Press the or button to adjust the contrast.
The OSD Controls The ON SCREEN DISPLAY shows its settings in one of eight languages. The default is English, but you can select French, Spanish, German, Italian, Simplify-Chinese, Korea, or Portuguese. 1) Press the button on the monitor. The MAIN CONTROLS window appears. LANGUAGE should be highlighted. 2) Press the button again. The LANGUAGE window appears. 3) Press the or button until the desired language is highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 4) Press the button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted... After returning to MAIN CONTROLS . . . . . . to continue to INPUT SIGNAL SELECTION, press the button until INPUT Smart Help SIGNAL SELECTION is highlighted. Next, follow steps 3 - 5 under INPUT SIGNAL SELECTION. . . .
The OSD Controls 3) Press the button. The INPUT SIGNAL SELECTION window appears. 4) Press the or 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. button to highlight INPUT B or INPUT A. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . . . . to continue to ZOOM, press the button until ZOOM is highlighted. Next, Smart Help follow steps 3 - 5 under ZOOM. . . .
The OSD Controls RETURN TO TOP OF THE PAGE ZOOM ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ZOOM is highlighted. 3) Press the button. The ZOOM window appears. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 4) Press the or button to adjust ZOOM. 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . . . . to continue to ADJUST HORIZONTAL, press the button until ADJUST Smart Help HORIZONTAL is highlighted. Next, follow steps 3 - 7 under ADJUST HORIZONTAL. . . .
The OSD Controls 3) Press the button. The ADJUST HORIZONTAL window appears. POSITION should be highlighted. 4) Press the or button to move the image to the left or right. 5) When the position is adjusted, press the press the button to return to MAIN CONTROLS window, or to highlight SIZE. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 6) To adjust the horizontal size, press the 7) When the size is adjusted, press the or button. button to return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . . . . to continue to ADJUST VERTICAL, press the button until ADJUST Smart Help VERTICAL is highlighted. Next, start with step 3 under ADJUST VERTICAL and follow the directions. . . .
The OSD Controls 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST VERTICAL is highlighted. 3) Press the button. The ADJUST VERTICAL window appears. POSITION should be highlighted. 4) Press the or button to move the image up or down. 5) When the position is adjusted, press the button to return to MAIN CONTROLS window, or file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls press the to highlight SIZE. 6) To adjust the vertical size, press the or button. 7) When the size is adjusted, press the button to return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . . . . to continue to ADJUST SHAPE, press the button until ADJUST SHAPE is Smart Help highlighted. Next, start with step 3 under ADJUST SHAPE and follow the directions. . . .
The OSD Controls These two options are PINCUSHION and BALANCED pincushion. Note: use these features only when the picture is not square. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button. The SIDE CURVE window appears. PINCUSHION should be highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 5) To adjust the pincushion, press the or 6) When the pincushion is adjusted, press the button. button to highlight BALANCED or press the button to return to the ADJUST SHAPE window. 7) To adjust the balanced pincushion, press the or 8) When the balanced pincushion is adjusted, press the button. button to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted.
The OSD Controls After returning to MAIN CONTROLS . . . ...to continue to ADJUST SIDE ANGLES, start with step 5 under ADJUST SIDE ANGLES and follow the directions. Smart Help ...to exit completely, press the button twice. ...to adjust only the BALANCED pincushion, follow steps 1 - 4 above, then press the button, and follow steps 7 - 9. ADJUST SIDE ANGLES ADJUST SIDE ANGLES under ADJUST SHAPE allows you to adjust two of the five preset options. These two options are TRAPEZOID and PARALLELOGRAM.
The OSD Controls highlighted. 4) Press the button to highlight ADJUST SIDE ANGLES. 5) Press the button. The SIDE ANGLES window appears. TRAPEZOID should be highlighted. 6) To adjust the trapezoid, press the or 7) When the trapezoid is adjusted, press the the button. button to highlight PARALLELOGRAM or press button to return to the ADJUST SHAPE window. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 8) To adjust the parallelogram, press the or 9) When the parallelogram is adjusted, press the button. button to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted. 10) Press the button to return to the MAIN CONTROLS window, or press the button until ROTATE IMAGE is highlighted. After returning to MAIN CONTROLS . . . ...to continue to ROTATE IMAGE, start with step 5 under ROTATE IMAGE and follow the directions. Smart Help ...
The OSD Controls 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the arrow until ROTATE IMAGE is highlighted. 5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 6) To adjust the rotation, press the or 7) When the rotation is adjusted, press the button. button to return to the ADJUST SHAPE window. BACK TO MAIN CONTROLS should be highlighted. 8) Press the button to return to MAIN CONTROLS. After returning to MAIN CONTROLS . . . . . . to continue to ADJUST COLOR, press the button until ADJUST COLOR is Smart Help highlighted. Next, start with step 3 under ADJUST COLOR and follow the directions. ...to exit completely, press the button twice.
The OSD Controls two options, smart model and professional model, which allows you to adjust colors on your screen to a setting you desire for high-end application. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST COLOR is highlighted. 3) Press the button. The ADJUST COLOR window appears. 4) Press the or button to highlight 9300K for GENERAL USE, 6500K for IMAGE file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls MANAGEMENT, 5500K for PHOTO RETOUCH, or USER PRESET or sRGB. 5) Once you have highlighted GENERAL USE, IMAGE MANAGEMENT, or PHOTO RETOUCH, or sRGB press the button to confirm you selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. 6a) Press the or button to highlight SMART MODEL. 6b) Once you have highlighted SMART MODEL press the 6c) Press the or button to confirm your selection. button to adjust the color temperature.
The OSD Controls 7b) USER PRESET is highlighted, press the the or button to highlight RED GAIN. Next, press button to adjust the color red gain. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 7c) When finished with RED GAIN, press the the or button to adjust the color green gain. 7d) When finished with GREEN GAIN, press the the or or button to highlight BLUE GAIN. Next, press button to adjust the color blue gain. 7e) When finished with BLUE GAIN, press the the button to highlight GREEN GAIN. Next, press button to highlight RED CUTOFF. Next, press button to adjust the color red cutoff. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 7f) When finished with RED CUTOFF, press the press the or button to highlight GREEN CUTOFF. Next, button to adjust the color green cutoff. button to highlight BLUE CUTOFF. Next, 7g) When finished with GREEN CUTOFF, press the press the or button to adjust the color blue cutoff. 7h) When all adjustments are complete, press the button to confirm your adjustments and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS. . . . .
The OSD Controls RESET TO FACTORY SETTINGS RESET TO FACTORY SETTINGS returns everything in all the windows to factory presets. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until RESET TO FACTORY SETTINGS is highlighted. 3) Press the button. The RESET TO FACTORY SETTINGS window appears. 4) Press the or button to select YES or NO. NO is the default. YES returns all settings to their original factory adjustments.
The OSD Controls 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . . . . to continue to EXTRA CONTROLS, press the button until EXTRA Smart Help CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS. . . . to exit completely, press the button.
The OSD Controls 3) Press the button. The EXTRA CONTROLS window appears. 4) Press the button until ADJUST MOIRE is highlighted. 5) Press the button. The ADJUST MOIRE window appears. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 6) Press the button until HORIZONTAL is highlighted. or To adjust the horizontal moire, press the 7) Press the button. button until VERTICAL is highlighted. To adjust the vertical moire, press the 8) When the moire is adjusted, press the or button. button to return to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS will be highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls After returning to MAIN CONTROLS . . . Smart Help . . . to exit completely, press the button. DEGAUSS EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussing removes electromagnetic build up that may distort the color on your screen. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until EXTRA CONTROLS is highlighted. 3) Press the button. The EXTRA CONTROLS window appears. Press the DEGAUSS is highlighted.
The OSD Controls 4) To degauss your screen, press the button. Your screen will be degaussed, then the MAIN CONTROLS window will reappear. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . . . . to continue to ADJUST MOIRE, press the Smart Help button until EXTRA CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS, ADJUST MOIRE. . . . to exit completely, press the button.
The OSD Controls 2) Press the button until EXTRA CONTROLS is highlighted. 3) Press the button. The EXTRA CONTROLS window appears. Note: If you have not degaussed the monitor, please follow the steps under the Extra Controls - Degauss section of this manual before adjusting the convergence. 4) Press the button until ADJUST CONVERGENCE is highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 5) Press the button. The ADJUST CONVERGENCE window appears. ADJUST HORIZONTAL is highlighted. 6) To adjust the horizontal convergence, press the or 7) When the horizontal convergence is adjusted, press the CONVERGENCE. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.htm (31 of 37)2005-08-10 ¤U¤È 01:05:50 button.
The OSD Controls 8) To adjust the vertical convergence, press the or button. 9) When the vertical convergence is adjusted, press the button to return to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS is highlighted. After returning to EXTRA CONTROLS . . . . . . to continue to ADJUST PURITY, press the button until ADJUST PURITY is highlighted. Next, start with step 4 under EXTRA CONTROLS ADJUST PURITY.
The OSD Controls 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until EXTRA CONTROLS is highlighted. 3) Press the button. The EXTRA CONTROLS window appears. Note: If you have not degaussed the monitor, please follow the steps under the Extra Controls - Degauss section of this manual before adjusting the purity. 4) Press the button until ADJUST PURITY is highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls 5) Press the . The ADJUST PURITY window appears. NS PUTRITY is highlighted. 6) Press the or button, to adjust NS PURITY and optimalize the purity performance. 7) When adjustment finished, press the button to return to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS is highlighted. file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
The OSD Controls After returning to EXTRA CONTROLS . . . . . . to continue to ADJUST PURITY, press the Smart Help button until AUTO CALIBRATE is highlighted. Next, start with step 4 under EXTRA CONTROLS AUTO CALIBRATE. . . . to exit completely, press the button twice. AUTO CALIBRATE (Not available in all models) EXTRA CONTROLS is a set of three features, including AUTO CALIBRATE.
The OSD Controls 3) Press the button. The EXTRA CONTROLS window appears. 4) Press the button until AUTO CALIBRATE is highlighted. 5) Press the or button to select OFF or AUTO. 6) When the selection is made, press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN WINDOW will be highlighted. 7) Press the button to exit the MAIN CONTROLS window. After returning to MAIN CONTROLS . . . Smart Help . . . to exit completely, press the button.
The OSD Controls RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19_6/edoc/english/osd/osd_cont.
F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
F1rst Choice Warranty ● Repairs or product modifications and alterations have been executed by unauthorized service organizations or persons; ● Damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect; ● Reception problems caused by signal conditions or cable or antenna systems outside the unit; ● Defects caused by abuse or misuse of the monitor; ● Product requires modification or adaptation to enable it to comply with local or national technical standards,
F1rst Choice Warranty Having the following information available will also help speed up the process: ● ● Your proof of purchase indicating: date of purchase, dealer name, model and product serial number. The full address to which the faulty monitor has to be collected and the swap model should be delivered. Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact Information. Or you can reach us via: Website: http://www.philips.
Your Guarantee in Central and Eastern Europe Your Guarantee in Central and Eastern Europe Dear Customer, Thank you for purchasing this Philips product, which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts during a period of 36 months from date of purchase.
Your Guarantee in Central and Eastern Europe Please note that the product is not defective under this guarantee in the case where modifications become necessary in order for the product to comply with local or national technical standards which apply in countries for which the product was not originally designed and/or manufactured. Therefore always check whether a product can be used in a specific country.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
International Guarantee Website: http://www.philips.com file:///D|/EDFU/crt_19_6/edoc/english/warranty/WAR_INTL.
United States Guarantee Philips F1rst Choice Warranty (USA / Canada) Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
United States Guarantee When the warranty on the original product expires, the warranty on all replaced and repaired products and parts also expires. WHAT IS EXCLUDED? Your warranty does not cover: ● ● ● ● ● ● labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product.
United States Guarantee discussed there may save you a service call. TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS... Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing: Philips Customer Care Center (877) 835-1838 or (919) 573-7855 (In U.S.A., Puerto Rico and U.S.
United States Guarantee This warranty gives you specific legal rights. You may have other rights which vary from state/ province to state/province. Before contacting Philips, please prepare the following details so we can solve your problem quickly.
F1rst Choice Contact Information F1rst Choice Contact Information Country Telephone number Tariff Austria 0820 901115 0.20 Belgium 070 253 010 0.17 Cyprus 800 92256 Free of Charge Denmark 3525 8761 Local call tariff Finland 09 2290 1908 Local call tariff France 08 9165 0006 0.23 Germany 0180 5 007 532 0.12 Greece 00800 3122 1223 Local call tariff Ireland 01 601 1161 Local call tariff Italy 199 404 042 0.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Belarus • Brasil • Bulgaria • Canada • Chile • China • Colombia • Croatia • Czech Republic • Dubai • Estonia • Hong Kong • Hungary • India• Indonesia • Korea • Latvia • Lithuania • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Russia • Romania • Serbia&Montenegro • Singapore • Slovakia • Slovenia • South Africa • Taiwan • Thailand • Turkey • Uruguay • U
Consumer Information Centers CROATIA Renoprom d.o.o. Mlinska 5, Strmec HR - 41430 Samobor +385 1 333 0974 ESTONIA FUJITSU SERVICES OU Akadeemia tee 21G EE-12618 Tallinn Tel: +372 6519900 www.ee.invia.fujitsu.com HUNGARY Serware Szerviz Vizimolnár u. 2-4 HU - 1031 Budapest Tel: +36 1 2426331 Email: inbox@serware.hu www.serware.hu LATVIA ServiceNet LV Jelgavas iela 36 LV-1055 Riga, Tel: +371 7460399 Email: serviss@servicenet.lv LITHUANIA ServiceNet LT Gaiziunu G.
Consumer Information Centers ROMANIA Blue Ridge Int'l Computers SRL 115, Mihai Eminescu St., Sector 2 RO - 020074 Bucharest Tel.:+40 21 2101969 SERBIA&MONTENEGRO Tehnicom Service d.o.o. Bulevar Vojvode Misica 37B YU – 11000 Belgrade Tel: +381 11 3060 886 SLOVAKIA Datalan Servisne Stredisko Puchovska 8 SK - 831 06 Bratislava Tel: +421 2 49207155 Email: servis@datalan.sk SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.
Consumer Information Centers RUSSIA Tel: +7 095 961-1111 Tel: 8-800-200-0880 Web-site: www.philips.ru TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.Cadde No:22 34776-Umraniye/Istanbul Tel: (0800)-261 33 02 UKRAINE Comel Shevchenko street 32 UA - 49030 Dnepropetrovsk Tel: +380 562320045 www.csp-comel.com Latin America ANTILLES Philips Antillana N.V.Kaminda A.J.E. Kusters 4 Zeelandia, P.O.
Consumer Information Centers BRASIL Philips da Amazonia Ind. Elet.Ltda. Rua Verbo Divino, 1400 -Sao Paulo-SP CEP-04719-002 Phone: 11 2121 0203 -São Paulo & 0800-701-0203 - Other Regions without São Paulo City. CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr.
Consumer Information Centers PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2136200 Fax : (01)-2136276 URUGUAY Rambla O'Higgins 5303 Montevideo Uruguay Phone: (598)-619 66 66 Fax : (598)-619 77 77 Customer Desk: Phone: 0004054176 VENEZUELA Industrias Venezolanas Philips S.A. Apartado Postal 1167 Caracas 1010-A Phone: (02) 2377575 Fax : (02) 2376420 Canada CANADA Philips Electronics Ltd.
Consumer Information Centers AUSTRALIA Philips Consumer Electronics Customer Care Centre. Level 1, 65 Epping Rd North Ryde NSW 2113 Phone: 1300 363 391 Fax:+61 2 9947 0063 NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (Toll Free) Fax:0800 288 588 Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA SHANHAI Rm 1007, Hongyun Building, No.
Consumer Information Centers HONG KONG Philips Electronics Hong Kong Limited Consumer Service Unit A, 10/F. Park Sun Building 103-107 Wo Yi Hop Road Kwai Chung, N.T. Hong Kong Phone: (852) 2619-9663 Fax: (852) 2481 5847 INDIA Phone: (020)-712 2048 ext 2765 Fax:(020)-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr.
Consumer Information Centers INDONESIA Philips Group of Companies in Indonesia Consumer Information Centre Jl.Buncit Raya Kav. 99-100 12510 Jakarta Phone: (021)-7940040 Ext 2100 Fax : (021)-7947511 / 7947539 KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong.
Consumer Information Centers PAKISTAN Philips Consumer Information Centre Mbuarak manzil, 39, Garden Road, Saddar, Karachi-74400 Phone: (9221)-2737 411-16 Fax:(9221)-2721 167 E-Mail:care@philips.com Web-site:www.philips.com.pk PHILIPPINES Philips Electronics&Lighting, Inc. Consumer Electronics 48F PBCOM Tower 6795 Ayala Avenue cor VA Rufino St.
Consumer Information Centers THAILAND Philips Electronics Thailand Ltd. 26-28th floor, Thai Summit Tower 1768 New Petchburi Road Khwaeng Bangkapi, Khet Huaykhwang Bangkok 10320 Thailand Phone : (66) 2-652 8652 email:cic Thai@philips.com Africa MOROCCO Philips Electronique Maroc 304,BD Mohamed V Casablanca Phone: (02)-302992 Fax : (02)-303446 SOUTH AFRICA PHILIPS SA (PTY) LTD Customer Care Centre 195 Main Road Martindale, Johannesburg P.O.
Consumer Information Centers file:///D|/EDFU/crt_19_6/edoc/english/warranty/WARCIC.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 1 It Takes Only A Moment To PROTECT YOUR INVESTMENT. Congratulations on investing in a Philips product. It’s an important and intelligent decision that’s sure to reward you for many years to come. To ensure you’ll get all of the privileges and protection that come with your purchase, please complete your Warranty Registration Card within the next ten days. SIMPLY MAIL THE CARD BELOW TO RECEIVE ALL OF THESE BENEFITS TO WHICH YOU’RE ENTITLED.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 2 !1375415338! PO BOX 1533 DEPOSIT NY 13754-1533 Please Open Promptly! TIME-DATED MATERIAL a PLEASE APPLY FIRST CLASS STAMP IMPORTANT Warranty Registration Card RETURN THE ATTACHED CARD WITHIN TEN DAYS TO ENSURE YOUR: ✓ Warranty Verification ✓ Owner Confirmation ✓ Model Registration See Inside For Valuable Benefits!
