Specifications

ManualsBrandsPhilips ManualsFlat Panel TV19PFL3403/98

Published by JY 0866 BU TV Consumer Care Printed in the Netherlands Subject to modification EN 3122 785 18130

retrieval system or transmitted, in any form or by any means, electronic,

mechanical, photocopying, or otherwise without the prior permission of Philips.

Color TV Chassis

TCS1.0L

I_17930_000.eps

240408

MG8

Contents Page Contents Page

1. Technical Specifications, Connections, and Chassis

Overview 2

2. Safety Instructions, Warnings, and Notes 5

3. Directions for Use 6

4. Mechanical Instructions 7

5. Service Modes, Error Codes, and Fault Finding 13

6. Block Diagrams, Test Point Overview, and

Waveforms

Wiring Diagram of Connector for MS19-PH 19" 21

Wiring Diagram of Connector for MS19-PH 26" 22

Block Diagram MS19P Chipset 23

I2C overview 24

7. Circuit Diagrams and PWB Layouts Diagram PWB

Main Power Supply (19") (A) 25 26

Main Power Supply (26") (A1) 27 28-29

Standby Power Supply (26") (A2) 30 31-32

SSB: Control (B01) 33 42-43

SSB: DC - DC (B02) 34 42-43

SSB: MST9E19A Controller (B03) 35 42-43

SSB: HDMI Interface (B04) 36 42-43

SSB: VGA Interface (B05) 37 42-43

SSB: Cinch (B06) 38 42-43

SSB: Tuner (B07) 39 42-43

SSB: Audio Amplifier (B08) 40 42-43

SSB: LVDS Interface (B09) 41 42-43

Keyboard Control Panel (E) 44 44

Inverter Panel (I) 45 46

IR LED Panel (J) 47 47

8. Alignments 49

9. Circuit Descriptions, Abbreviation List, and IC Data

Sheets 50

Abbreviation List 51

IC Data Sheets 53

10. Spare Parts List & CTN Overview 57

11. Revision List 57

Summary of content (57 pages)

PAGE 1
Color TV Chassis TCS1.0L LA MG8 I_17930_000.eps 240408 Contents Page 1. Technical Specifications, Connections, and Chassis Overview 2 2. Safety Instructions, Warnings, and Notes 5 3. Directions for Use 6 4. Mechanical Instructions 7 5. Service Modes, Error Codes, and Fault Finding 13 6. Block Diagrams, Test Point Overview, and Waveforms Wiring Diagram of Connector for MS19-PH 19" 21 Wiring Diagram of Connector for MS19-PH 26" 22 Block Diagram MS19P Chipset 23 I2C overview 24 7.
PAGE 2
EN 2 1. Technical Specifications, Connections, and Chassis Overview TCS1.0L LA 1. Technical Specifications, Connections, and Chassis Overview 1.1.3 Index of this chapter: 1.1 Technical Specifications 1.2 Connection Overview 1.3 Chassis Overview Notes: • Figures can deviate due to the different set executions. • Specifications are indicative (subject to change). 1.1 Technical Specifications 1.1.1 Vision Display type Screen size Resolution (H × V pixels) Light output (cd/m2) Typ.
PAGE 3
Technical Specifications, Connections, and Chassis Overview 1.2 TCS1.0L LA 1. EN 3 Connection Overview 10 9 8 1 3 2 4 5 6 7 I_18130_001.eps 160608 Figure 1-1 Rear and side I/O connections Note: The following connector color abbreviations are used (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= Grey, Rd= Red, Wh= White, and Ye= Yellow. 3 - VGA PC: Video RGB - In and Service UART 1 5 10 6 15 11 1.2.1 Rear Connections E_06532_002.
PAGE 4
EN 4 1.2.2 1. TCS1.0L LA Technical Specifications, Connections, and Chassis Overview Side connections 8 - Cinch: Video CVBS - In, Audio - In Ye - Video CVBS 1 VPP / 75 Ω Wh - Audio L 0.5 VRMS / 10 kΩ Rd - Audio R 0.5 VRMS / 10 kΩ jq jq jq 9 - S-Video (Hosiden): Video Y/C - In 1 - Ground Y Gnd 2 - Ground C Gnd 3 - Video Y 1 VPP / 75 Ω 4 - Video C 0.3 VPPP / 75 Ω H H j j 10 - Mini Jack: Audio Head phone - Out Bk - Head phone 32 - 600 Ω / 10 mW 1.
PAGE 5
Safety Instructions, Warnings, and Notes TCS1.0L LA 2. EN 5 2. Safety Instructions, Warnings, and Notes • Index of this chapter: 2.1 Safety Instructions 2.2 Warnings 2.3 Notes 2.1 Safety Instructions 2.3.2 Safety regulations require the following during a repair: • Connect the set to the Mains/AC Power via an isolation transformer (> 800 VA). • Replace safety components, indicated by the symbol h, only by components identical to the original ones.
PAGE 6
EN 6 2.3.5 3. TCS1.0L LA Directions for Use Alternative BOM identification MODEL The third digit in the serial number (example: AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the specific TV set. In general, it is possible that the same TV model on the market is produced with e.g. two different types of displays, coming from two different suppliers. This will then result in sets which have the same CTN (Commercial Type Number; e.g.
PAGE 7
Mechanical Instructions TCS1.0L LA 4. EN 7 4. Mechanical Instructions Index of this chapter: 4.1 Cable Dressing 4.2 Service Positions 4.3 Assy/Panel Removal 4.4 Set Re-assembly 4.1 Notes: • Figures below can deviate slightly from the actual situation, due to the different set executions. • Follow the disassemble instructions in described order. They apply mostly to the 26" model unless otherwise specified, but the described method is comparable for the other screen sizes. Cable Dressing I_17950_003.
PAGE 8
EN 8 4. TCS1.0L LA Mechanical Instructions I_17950_004.
PAGE 9
Mechanical Instructions 4.2 4.2.1 TCS1.0L LA 4. EN 9 Service Positions For easy servicing of this set, there are a few possibilities created: • The buffers from the packaging. • Foam bars (created for Service). 1 1 Foam Bars 1 1 1 I_17950_005.eps 080508 Figure 4-4 Stand 4.3.2 1 Required for sets 42" E_06532_018.eps 171106 Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover. 1. Refer to next figures. 2.
PAGE 10
EN 10 4. Mechanical Instructions TCS1.0L LA 4.3.4 IR/LED Board and Speakers 1. Refer to next figure. 2. Remove the screws [1] and remove the IR/LED board. 3. Remove the screws [2] and remove the speakers. When defective, replace the whole unit. 4 4 2 4 1 2 2 1 I_17930_043.eps 240408 I_17930_042.eps 240408 Figure 4-6 Speaker and IR/LED panel cable release 4.3.3 Keyboard Control Board 1. Refer to next figure. 2. Unscrew two screws[1] 3. Unplug connector [2] and remove the board.
PAGE 11
Mechanical Instructions 4.3.5 4.3.6 Power Supply Board TCS1.0L LA 4. EN 11 Inverter Board (19" and 22" versions) Due to different set executions this chassis some versions are supplied with an inverter board. Figures may differ. 1. Refer to next figure. 2. Unplug all connectors [1]. 3. Release the clips [2] 4. Take out the inverter board. Due to different set executions this chassis is supplied with one or two power supply boards and figures may differ.
PAGE 12
EN 12 4. Mechanical Instructions TCS1.0L LA 2 2 4 4 3 2 2 I_17950_008.eps 080508 Figure 4-12 SSB 4.4 Set Re-assembly To re-assemble the whole set, execute all processes in reverse order. Notes: • While re-assembling, make sure that all cables are placed and connected in their original position. See figure “Cable dressing”. • Pay special attention not to damage the EMC foams at the SB shields. Make sure, that EMC foams are put correctly on their places.
PAGE 13
Service Modes, Error Codes, and Fault Finding TCS1.0L LA 5. EN 13 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: 5.1 Test Points 5.2 Service Mode 5.3 Error Codes 5.4 Fault Finding 5.5 Service Tools 5.6 Software Upgrading 5.1 Test Points This chassis is NOT equipped with test points in the service printing. No test points are mentioned in the service manual. I_18130_043.eps 190608 5.2 Service Mode 5.2.
PAGE 14
EN 14 5. TCS1.0L LA Service Modes, Error Codes, and Fault Finding I_18130_049.eps 190608 Figure 5-7 SAM menu, Picture Mode, Natural I_18130_052.eps 190608 Figure 5-10 SAM menu, Picture Mode, Soft I_18130_053.eps 190608 Figure 5-11 SAM menu, Producting I_18130_050.eps 190608 Figure 5-8 SAM menu, Picture Mode, Personal I_18130_051.eps 190608 Figure 5-9 SAM menu, Picture Mode, Rich I_18130_054.
PAGE 15
Service Modes, Error Codes, and Fault Finding TCS1.0L LA 5. EN 15 I_18130_055.eps 190608 I_18130_059.eps 190608 Figure 5-13 SAM menu, Setup Figure 5-15 SAM menu, Clear Code > How to Exit Press “MENU” on the RC-transmitter. Factory Mode Descriptions Item Sub-Item Description SOURCE Shift among sourcing via pressing Left & Right key ADC ADJ Only available in HDTV or PC mode WB White Balance Calibration setting SOURCE Shift among sources COLOR TEMP Normal, Warm, Cool I_18130_058.
PAGE 16
EN 16 5. Service Modes, Error Codes, and Fault Finding TCS1.0L LA Item Sub-Item Description Setting /55 /77 /78 PRODUCTING FACTURY HOT KEY Short-cut key to enter factory mode setting: GO BACK is the short-cut key if it is “ON”. Do remember to turn this “OFF” when the set is returned to the customer.
PAGE 17
Service Modes, Error Codes, and Fault Finding Any RC command terminates the sequence. Error code LED blinking is in white color. Example: the contents of the error buffer is “013 007 000 000 000”. After entering SDM, the following occurs: • 1 long blink of 5 seconds to start the sequence • 1 medium blink of 3 seconds and then 3 short blinks followed by a pause of 1.5 seconds • 7 short blinks followed by a pause of 1.5 seconds • 1 long blink of 1.5 seconds to finish the sequence.
PAGE 18
EN 18 5. TCS1.0L LA Service Modes, Error Codes, and Fault Finding Picture OK, No sound Check the voltage of Pin 3,13 of U19,is it 12v? No Check Q17 Yes NO Check Mute Pin6 of U19,is it 12V? Check B of Q22 is Low OK? Yes No Check the AMPMUTE circuit Yes Check the wave of pin74,75 of U8,is it OK? No TV source Yes Check SIF circuit Pin 7(SIFOUT) of Tuner TU1 Yes Check R & L speaker No Check wave of Audio input Pin U8 pin61~69.
PAGE 19
Service Modes, Error Codes, and Fault Finding TCS1.0L LA 5. No color Color system is Right & another channel color is right ? No Reset To Local system Yes Dose the TV signal too weak? Check Pin 17(TVCVBS) Wave of TU1 OK? NO YES Check Tuner Input cable & antenna NO Replace TU1 YES Fine tune Frequency I_18130_006.
PAGE 20
EN 20 5. TCS1.0L LA Service Modes, Error Codes, and Fault Finding Picture OK, No sound Check the voltage of Pin 3,13 of U19,is it 12v? No Check PSU Yes NO Check Mute Pin6 of U19,is it 12V? Yes Check the wave of pin74,75 of U8,is it OK? No TV source Yes Check SIF circuit Pin 7(SIFOUT) of Tuner TU1 No Check B of Q22 is Low OK? Check the AMPMUTE circuit Yes Yes Check R & L speaker No Check wave of Audio input Pin U8 pin61~69.
PAGE 21
+12V +12V GND NC +12V +12V GND GND GND 5V-PW 5V-PW NC +5VSTB +5VSTB GND GND +12V-PW +12V-PW +12V-PW +12V-PW LED2 1 2 3 4 5 6 7 8 9 10 PS1 LED1 GND IR 40-PF3403-IRC1XG IR BOARD 1 2 3 4 5 6 7 8 9 10 +5VSTB 1 2 3 4 5 40-PF3403-KEC1XG KEY BOARD +5VSTB 1 2 3 6. LED2-IN CN2001 GND KEY1 KEY0 P1001 1 2 3 4 5 6 TCS1.
PAGE 22
1 2 3 4 5 6 7 8 P5 NC BL-ADJUST BL-ON/OFF GND GND NC NC NC GND GND +12V-PW +12V-PW +12V-PW GND NC GND NC NC NC NC NC BL-ADJUST BL-ON/OFF 12V-PW 12V-PW GND GND 12V-PW 12V-PW LED2 11 2 2 3 3 4 4 5 5 6 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 15 15 16 16 P4 LED1 GND 1 2 3 4 5 1 2 3 40-PF3403-IRC1XG IR BOARD +12V-PW P22 +5VSTB IR +5VSTB 1 2 3 P1001 CN2001 GND KEY1 KEY0 +5STB AGND PW-ON/OFF 6.
PAGE 23
Block Diagrams, Test Point Overview, and Waveforms TCS1.0L LA 6. 23 Block Diagram MS19P Chipset MS19P Chipset Block Diagram EDID U13 24C02 HDMI SDA/SCL EDID External device U12 24C02 VGA HDTV Y/C AV1 AV2 AV-OUT TV SIF Z1 PC/HDTV-R/L AV1-R/L AV2-R/L HDCP SDA/SCL 24C04 Panel U11 8/10-bit LVDS MST9U19A U19 Audio out AMP Speaker TDA7266 IR/KEY0/KEY1 GPIO / PWM U10 EEPROM Earphone U9 SCL 24C32 SDA 2MB SPI Serial-Flash I_18130_063.
PAGE 24
Block Diagrams, Test Point Overview, and Waveforms TCS1.0L LA 6. 24 I2C overview I2C Device Block Diagram Tuner ˄integrated IF PLL Demodulator˅ I2C Address:A0 SDA1 SCL1 MST9U19A-LF SDA SCL 24C32 SDA SCL 24C04 System EEPROM HDCP EEPROM I2C Address:A0 I2C Address:A4 I_18130_064.
PAGE 25
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 25 7. Circuit Diagrams and PWB Layouts Main Power Supply (19") A MAIN POWER SUPPLY 19” A I_18130_022.
PAGE 26
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 26 Layout Main Power Supply (19") (Top Side) I_18130_023.eps 180608 Layout Main Power Supply (19") (Bottom Side) I_18130_065.
PAGE 27
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 27 Main Power Supply (26") A1 MAIN POWER SUPPLY 26” A1 I_18130_024.
PAGE 28
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 28 Layout Main Power Supply (26") (Top Side) 40-PWL01B-STE1XG I_18130_028.
PAGE 29
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 29 Layout Main Power Supply (26") (Bottom Side) 40-PWL01B-STE1XG I_18130_029.
PAGE 30
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 30 Standby Power Supply (26") A2 STANDBY POWER SUPPLY 26” A2 I_18130_025.
PAGE 31
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 31 Layout Standby Power Supply (26") (Top Side) 40-1PL37C-PWF1XG I_18130_026.
PAGE 32
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 32 Layout Standby Power Supply (26") (Bottom Side) I_18130_027.
PAGE 33
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 33 SSB: Control CONTROL +5VSTB C2 0.1U 5 6 3 4 1 2 AGND R259 10K C PW_ON/OFF R177 Z51 T B 4K7 R178 NC Q26 BT3904 C B R266 10K LL4148 D45 Q27 BT3904 C B E R261 8K2 +12V D41 LL4148 AGND R267 10K R262 47K R260 10K Normal--H Protect--L AGND +5VSTB 0.1U NC R258 100K 3K9 R278 0.9V +5V E Q30 BT3904 E R268 10K 8 1.
PAGE 34
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 34 SSB: DC - DC 4 4 D7 FM120 2 +3.3V C42 0.1U C36 0.1U C41 2U2 C40 0.1U C39 0.1U R29 0R C37 47U NC R28 16V pin6 pin12 C38 2U2 AGND +3.3AVDD FOR AVDD_AU AVDD_HDMI L41 FB L19 FB VOUT AVDD_AU +3.3VA +3.3VA U6 AIC1084 D9 FM120 AGND C34 0.1U C32 0.1U D8 FM120 C35 100U C30 0.1U L17 FB 16V C33 100U 16V C31 100U 16V +5VSTB D6 FM120 1 +5VSTB_L 3 L16 100R +3.3AVDD for AVDD_HDMI ! VIN +3.3VA +5VST F3 3.
PAGE 35
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 35 SSB: MST9E19A Controller +5VSTB R33 100R AMP-ROUT AMP-R R34 100R PH-R1OUT R54 4K7 PH-ROUT LED1 R58 4K7 LED2 R13 4K7 C77 1000P C76 0.01U 0R RS2 AGND R45 100R C Q9 BT3904 B AGND PH-L1OUT R59 1K KEY0 KEY0-IN 1 KEY1 R51 22K C83 0.01U Q7 BT3904 E E AGND R47 100R R50 22K PH-LOUT C82 0.01U RS1 1K AMP-L C B KEY1-IN 2 1K R60 3 IR-IN R32 10K 16V C74 47U 1 3 D40 0BAV99 2 AMP-LOUT R11 4K7 R36 22K RS3 NC R38 22K +3.
PAGE 36
Circuit Diagrams and PWB Layouts TCS1.0L LA 7.
PAGE 37
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 37 SSB: VGA Interface B05 VGA INTERFACE B05 VGA/5V P13 16 5 15 10 R144 100R 4 PROTECT 14 9 C121 0.047U R103 10R VGA-B+ 3 BIN+ 13 8 2 C122 0.047U R104 10R VGA-G+ GIN+ 12 7 1 VGA-R+ R105 10R C123 0.047U R106 330R C124 1000P RIN+ 17 BIN- 3 3 SOG C125 0.047U R110 47R D22 D21 D20 3 1 1 1 R109 75R R107 75R 6 R108 75R P13-11 11 2 2 2 AGND AGND R111 47R C126 0.047U R113 47R C127 0.
PAGE 38
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 38 SSB: Cinch CINCH R281 5K1 B06 DVI-RIN R145 12K C138 560P 2 D33 C9 470P 1 R161 12K 2 D37 NC C4 470P 3 3 For DVI Audio Input(3.5mm Jack) 1 AV1 In Rear R289 5K1 AV1-RIN NC AV1_R 3 PC-RIN 2 1 C139 0.
PAGE 39
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 39 SSB: Tuner TUNER B07 VIDEO 17 AFT GND2 16 15 NC6 TU 14 AGC SDA MB 13 12 11 10 GND1 SIFOUT SCL 9 8 AUDIO 6 7 NC4 5 NC5 NC3 4 NC2 3 2 1 NC1 TU1 R202 51K AFT L27 22UH 3 16V C169 220U 16V R203 100K C166 0.
PAGE 40
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 40 SSB: Audio Amplifier AUDIO AMPLIFIER B08 P9 TO SPEAKER AMP-PROUT- 4 AMP-PROUT- 3 AMP-RIN 2 AMP-LIN AMP-PROUT+ 1 C203 2U2 AMP-R C205 2U2 H8 1 4 IN1 2 5 NC1 C206 1000P C26 OUT1- 3 VCC1 0.022U 6 MUTE C25 7 STBY TDA7266 0.022U AGND 1 OUT1+ 2 C204 1000P C194 NC AMP-L U19 C195 NC AMP-PLOUT- PGND 8 PW_GND 9 S_GND 12V-AMP AGND 10 NC2 L31 27UH +12V 11 NC3 12 IN2 C217 220U C209 0.
PAGE 41
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 41 SSB: LVDS Interface B09 LVDS INTERFACE B09 Personal Notes: P10 AGND 39 40 RXO0+/R6 37 38 RXO0-/R7 RXO1+/R4 35 36 RXO1-/R5 +3.
PAGE 42
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 42 Layout Small Signal Board (Top Side) I_18130_020.
PAGE 43
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 43 Layout Small Signal Board (Bottom Side) I_18130_021.
PAGE 44
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 44 Keyboard Control Panel E Personal Notes: KEYBOARD CONTROL PANEL R1002 1K5 AGND P1001 R1001 1K2 3 K1001 R1006 1K5 KEY0 R1005 1K2 D1002 D1001 HS5V6B 1 KEY1 HS5V6B 2 1 2 1 2 K1006 E R1003 2K 3 4 1 2 3 4 1 2 AGND R1004 NC K1004 R1007 2K K1002 3 4 1 2 3 4 1 2 AGND K1005 3 R1008 4 NC K1003 3 4 AGND AGND I_18130_030.eps 180608 Layout Keyboard Control Panel (Top Side) I_18130_031.
PAGE 45
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 45 Inverter Panel 1 I CN1 D INVERTER PANEL 19” F1 FUSE-1 I C1 220uF/250V 1 2 3 4 5 6 R2 200 R1 200 C3 104 C2 104 R27 10 Q2 2222 C20 223 G1 3 R28 10 Q3 2222 DTA143 1 C21 223 2 3 R30 10 4 C4 E1 E2 C2 VCC OUTPUTC VREF A2- A2+ Q7 2907 R19 560 U1 OVP 3K R61 510K 330pF R13 100K C15 NC 6.8K 15K S2 D2 G2 D2 8 10 T.
PAGE 46
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 46 Layout Inverter Panel (Top Side) I_18130_034.eps 190608 Layout Inverter Panel (Bottom Side) I_18130_035.
PAGE 47
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 47 IR LED Panel J Layout IR LED Panel (Top Side) IR & LED PANEL J CN2001 5 LED2 5V 4 LED1 G2001 C B C B Q2002 E R2001 4K7 LED2 E C2002 47P D2001 1K2 IR BC847A Q2001 BC847A R2004 IR GND AGND R2002 LED1 4K7 R2003 1K2 5V C2001 100U 16V 1 IR C2003 47P 2 VCC 3 2 AGND W AGND R 3 1 I_18130_036.eps 180608 I_18130_037.eps 180608 Layout IR LED Panel (Bottom Side) I_18130_038.
PAGE 48
Circuit Diagrams and PWB Layouts TCS1.0L LA 7. 48 Personal Notes: E_06532_013.
PAGE 49
Alignments TCS1.0L LA 8. EN 49 8. Alignments Index of this chapter: 8.1 Electrical Alignments 8.2 Hardware Alignments Note: The Service Modes are described in chapter 5. Menu navigation is done with the CURSOR UP, DOWN, LEFT or RIGHT keys of the remote control transmitter. 8.1 Electrical Alignments Perform all electrical adjustments under the following conditions: • Power supply voltage (depends on region): – AP-NTSC: 120 VAC or 230 VAC / 50 Hz (± 10%). – AP-PAL-multi: 120 - 230 VAC / 50 Hz (± 10%).
PAGE 50
EN 50 9. TCS1.0L LA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: 9.1 Introduction 9.2 Abbreviation List 9.3 IC Data Sheets Notes: • Only new circuits (circuits that are not published recently) are described. • Figures can deviate slightly from the actual situation, due to different set executions. 9.
PAGE 51
Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.
PAGE 52
EN 52 9. OSD PAL PC PCB PDP PIG PIP PLL Progressive Scan PWB RAM RC RC5 (6) RGB RGBHV ROM SAM SC SC1-OUT SC2-B-IN SC2-C-IN SC2-OUT S/C SCL SD SDA SDI SDM SDRAM SECAM SIF SMPS SND SNDL-SC1-IN SNDL-SC1-OUT SNDL-SC2-IN SNDL-SC2-OUT SNDR-SC1-IN SNDR-SC1-OUT SNDR-SC2-IN SNDR-SC2-OUT SNDS-VL-OUT SNDS-VR-OUT SOPS S/PDIF SRAM STBY SVHS SW THD TXT uP VL VCR TCS1.0L LA Circuit Descriptions, Abbreviation List, and IC Data Sheets On Screen Display Phase Alternating Line.
PAGE 53
Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3 TCS1.0L LA 9. IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
PAGE 54
EN 54 9.3.2 9. TCS1.0L LA Circuit Descriptions, Abbreviation List, and IC Data Sheets Diagram B, TDA1308 Block diagram OUTA INA(neg) INA(pos) VSS 1 TDA1308(A) 8 VDD 2 3 7 6 4 5 OUTB INB(neg) INB(pos) Pinning information TDA1308(A) OUTA 1 8 VDD INA(neg) 2 7 OUTB INA(pos) 3 6 INB(neg) VSS 4 5 INB(pos) I_18130_007.
PAGE 55
Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.3 TCS1.0L LA 9. EN 55 Diagram B, NCP1377B Block diagram 1.5 us for B Version 4.5 us Delay Demag HV OVP Demag PON 4 mA /1.44 5V + 8 us Blanking + + S + + VCC S R + 3 us for B Version Q 10 V Rint VCC Drv Q R 12.5 V 7.5 V 5.6 V (Fault) To Internal Supply 50 mV Driver src = 20 sink = 10 4.2 V Fault Mngt.
PAGE 56
EN 56 9.3.4 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets TCS1.0L LA Diagram B, TDA7266 Block Diagram VCC 470µF 3 0.22µF 4 IN1 + 100nF 13 1 OUT1+ 2 OUT1- 15 OUT2+ 14 OUT2- ST-BY 7 S-GND 0.22µF IN2 9 - Vref + 12 + - MUTE 6 PW-GND 8 + Pin Configuration 15 OUT2+ 14 OUT2- 13 VCC 12 IN2 11 N.C. 10 N.C. 9 S-GND 8 PW-GND 7 ST-BY 6 MUTE 5 N.C. 4 IN1 3 VCC 2 OUT1- 1 OUT1+ I_17950_054.
PAGE 57
Spare Parts List & CTN Overview 10. Spare Parts List & CTN Overview For the latest spare part overview, please consult the Philips Service website. Table 10-1 Sets described in this manual: CTN Styling 19PFL3403/55 MG8 19PFL3403/77 MG8 19PFL3403/78 MG8 19PFL3403/85 MG8 26PFL3403/85 MG8 11. Revision List Manual xxxx xxx xxxx.0 • First release. TCS1.0L LA 10.