Technical data
26
150MT10P LMT
Go to cover page
Electrical instructions
2.3.2 Table2 for Europe and AP-multi
Signal Distribution Table (PAL Cable)
Frequency Carriers
PRG CH
Video Sound
TV System
Pattern
0
1
AU37 590.25MHz 595.75MHz PAL B(UK) Pure White
2
AU2 64.25MHz 69.75MHz PAL B(UK) Circle Pattern
3
E7 189.25MHz 194.75MHz
PAL B
(CCIR)
Circle Pattern
4
G47 679.25MHz 684.75MHz
PAL G
(CCIR)
Circle Pattern
5
I23 487.25MHz 493.75MHz
PAL I
(UK)
Circle Pattern
6
E12 224.25MHz 229.75MHz
PAL B
(CCIR)
Color Bar
7
AU7 182.25MHz 187.75MHz
PAL B
(UK)
Color Bar
8
G68 847.25MHz 852.75MHz
PAL G
(CCIR)
100% White
9
AU9 196.25MHz 201.75MHz
PAL B
(UK)
Checkerboard
10
AU10 209.25 MHz 214.75 MHz
PAL B
(UK)
Crosshatch
11
AU0 46.25MHz 51.75MHz
PAL B
(UK)
Color Bar
12
AU2 64.25MHz 69.75MHz
PAL B
(UK)
Color Bar
13
AU5 102.25 MHz 107.75 MHz
PAL B
(UK)
Crosshatch
14
AU5A 138.25MHz 143.75MHz
PAL B
(UK)
Color Bar
15
AU7 182.25MHz 187.75MHz
PAL B
(UK)
Pure White
16
AU9 196.25MHz 201.75MHz
PAL B
(UK)
Pure White
17
AU10 209.25MHz 214.75MHz
PAL B
(UK)
Circle Pattern
18
I23 487.25MHz 493.75MHz
PAL I
(UK)
Circle Pattern
19
G28 527.25MHz 532.75MHz
PAL G
(CCIR)
Circle Pattern
20
AU37 590.25MHz 595.75MHz
PAL G
(UK)
Circle Pattern
21
I40 623.25MHz 629.75MHz
PAL I
(UK)
Color Bar
22
CH44 655.25MHz 661.75MHz
PAL DK
(UK)
Color Bar
23
I60 783.25MHz 789.75MHz
PAL I
(UK)
100% White
24
I66 831.25MHz 837.75MHz
PAL I
(UK)
Checkerboard
25
K21 471.25 MHz 477.75 MHz
SEC K1
(CCIR)
Crosshatch
28
G28 527.25MHz 532.75MHz
PAL G
(UK)
Color Bar
Table 2
3.AC adaptor
3.1Setup the AC I/P at 90VAC, and Output DC loading at 4.5 Amp,
The DC output voltage is12 .1V DC
3.2 Adjustment is nothing to do
4.PC mode Display Adjustment
4.1Display quality adjustment
Use timing mode as describe in 2.2, and use the POPO
(pixel on pixel off) pattern to adjust the clock until no stripe and
adjust the phase until clear picture.
Check all pre-setting 140 modes.
4.2 WHITE-D adjustment (B)
4.2.1At factory mode apply 60KHz/75Hz mode with crosshatch
pattern .
Set main controls brightness control at 100% and contrast to
50% .Set auto-sub function for auto offset and sub-con setup
4.2.2Apply white pattern, set brightness control at 100%, and
contrast control at 50%.Preset R,G,B gain at 127.
Adjust the R,G,B gain of Scalar in Factory Mode. (see Fig 1.)
The 1931 CIE chromaticity (X, Y) co-ordinates shall be :
Use Minolta CA-110 for color coordinates and luminance
Check.
Luminance> 250 Nits ( CPT ) in the center of the screen at
Original color and PC Brightness control ;Contrast control at
100%
Note : After white-D adjustment set brightness and contrast
at 50%
4.3 Check the digital interface cable
Check the 64 grey level color poor & noise condition.
9300K 6500K
x (center) 0.281 0.005 0.312 0.005
y (center) 0.311 0.005 0.338 0.005
!
!
!
5.0 TV Mode display adjust
5.1.1Geometry Adjustment (B)
A)
Equipment :PM5515, PM5518 or FLUKE 54200
Input Signal Type :1.1 for RF input signal
within PAL system ( for Europe
and AP version ) , channel : E7
(189.25MHz)the pattern is using
circle and cross hatch pattern
2. for S- Video input signal , within
NTSC system ( for Europe and
AP version ) , the pattern is using
Circle and cross hatch pattern
input Signal Strength :>= 1mV rms (60 dBuV) terminal
Voltage.
1Vpp Y-signal , 300mVpp C-signal
Input Injection Point :Aerial input and S- Video input
B)
Initial Set-up : Set smart picture to Natural.
Method of Alignments : a. select to TV channel , then adjust
vertical shift .and horizontal shift to
picture center then save .
b. select to S-video Adjust vertical
shift .and horizontal shift to picture
center then save .
INPUT REQUIREMENTS
ALIGNMENT METHOD