5" TFT LCD Colour Monitor LCD / TV Service Service Service Smart Interface/PnP/Sliding Height Adjustment High Bright Picture/Auto Picture Adjustment/Wide Viewing Angle Horizontal frequencies 30 - 61 kHz TABLE OF CONTENTS Page Description Important Safety Notice..................................2 Technical Data .............................................3 TV control......................................................4~6 TV OSD menus..............................................
150MT10P LMT Important Safety Notice Go to cover page Proper service and repair is important to the safe, reliable operation of all Philips Consumer Electronics Company** Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
Technical Data Technical Specifications LCD Panel Screen type Screen dimensions Pixel pitch LCD Panel type Effective viewing area Display Colors : TFT LCD : 15 " visual : 0.297 x 0.297 mm(15.0") : 1024 x 768 pixels R.G.B. Vertical stripe Anti-glare polarizer hardness : 304.1 x 228.1 mm (15.
150MT10P LMT TV control Go to cover page Use your remote controlier 1 2 3 4 PIP Shift PIP On/Off, Size AV source Smart sound controlsTo access a series of settings: VOICE, MUSIC, THEATRE and return to PERSONAL 5 Menu To display or exit from the menus 6 Cursor These 4 keys are used to move within the menus 7 Volume To adjust the sound level 8 Mute To disable or enable the sound 9 Teletext features 10 Sound mode To switch from STEREO to MONO or to choose between Dual I and Dual II for bilingual transm
TV Control 150MT10P LMT 5 Go to cover page Using the Teletext (for areas where teletext service is available) Press button presents a list of subjects to which you have Teletext is an information system broadcast by certain TV access. Each subject has a corresponding channels which can be consulted in the same way as a newspaper. It also provides subtitles for the hard of hearing or Result on Screen Display or exit teletext. The main index page 1On/Off teletext page number (always 3 digits).
150MT10P LMT TV control Go to cover page Using the Programme Listing Programme listing feature allows you to navigate through a list of installed programmes for a quick overview of the channels installed on your television Press buttonResult 1.Display the list of installed programmes. The current channel is highlighted. 2.Cycle through the programme list and highlight the channel number you want to view. 3.Activate the channel you have selected. 4.
TV OSD Menus 150MT10P LMT 7 Go to cover page Using other menus (With remote controller) 1.First carry out operations 1 to 8 above, then: 2.Press once to select AUTO STORE then press . The search begins. After several minutes, the INSTALL menu Reappears Automatically. 3.If the transmitter or the cable network broadcasts the automatic sort signal, the programmes will be correctly numbered. 4.If not, the programmes found will be numbered in descending order starting at 99, 98, 97, etc.
TV OSD menus 150MT10P LMT Go to cover page Sorting programmes 6.Use 1.Press MENU key. The main menu is displayed. 7.Press MENU when the name has been entered. 2.Select INSTALL ( ), then press . The INSTALL keys to choose the characters. The programme name is stored. 8.Repeat steps 4 to 7 for each programme to be Named. menu appears. 9.To exit from the menus, press . Adjusting the picture 1.Press MENU then 3.Using the key, select SORT then press . The PICTURE menu Appears: .
TV OSD Menus 150MT10P LMT 9 Go to cover page Adjusting the sound Timer function 1.Press MENU, select the SOUND option ( The SOUND menu appears: ) and press . This menu allows you to use your TV as an alarm Clock. 1.Press MENU. 2.Select FEATURES ( ), and press twice. The TIMER menu appears: 2.Use keys to select a setting and keys to Adjust. Note: to access the AVL setting (hidden at the bottom of the screen) hold down key. 3.
TV OSD menus 150MT10P LMT Go to cover page Locking the set You can bar access to certain programmes or completely lock the set by locking the keys. Locking programmes 1.Press MENU. 2.Select FEATURES ( ) and press 3.Select PARENTAL. CONT. ( . ) and press . 4.Enter your confidential access code. The first time, enter the code 0711 then confirm by re-entering 0711. The menu appears. 5.Press to go into the menu. 6.Use keys With to select the required programme and confirm .
Connection to PC Setting up and connecting your monitor/TV Make sure to power off your monitor/TV befoe the installation. -Connecting the monitor/TV .Connect the cables to theback of your monitor/TV by following step 1~7: 150MT10P LMT 11 Go to cover page Connect to PC 1. Connect the cables to back of your computer by following step 1~6. 2.Power on your computer and monitor/TV, make sure the PC mode is selected( ). If it is not, please push the PC, TV/VIDEO selection button to select the PC mode. 3.
Connection to PC 150MT10P LMT Go to cover page Connect to DVD/VCR /VCD through SCART (for Europe) Accessory Pack Unpack all the pats. Power cable WE : 3138 128 74931 NAFTA : 3138 128 74901 Remote controller & batteries Not included accessory RC25106/00 : 3139 228 89481(WE) RC25107/00 : 3139 228 89471(NAFTA) BAT ZNC 1.
Description of Controls 150MT10P LMT 13 Go to cover page Front View Product Description 1 PIP Activate PIP (Picture in Picture) window and select size 2 PC<->TV/Video Switch the monitor between PC mode and TV/Video mode 3 VIDEOSOURCE TV/Video source selection 4 Power switch On/Off 5 Increase or decrease the channel number Or up or down the highlighted function in OSD 6 Automatically adjust the H/V position, phase and clock Setting 7 Increase or decrease the level of audio volume Or decrease or decrease
150MT10P LMT Description of Controls Go to cover page (North America and Asia Pacific) 1.DC 12V DC 12V power in 2.PC - Video D-Sub input 3.PC - Audio PC Stereo input 4.S-VIDEO (L) AV audio (L) S-VIDEO AV audio (R) 5.S-VIDEO S-VIDEO in 6.L R - AV IN 6a Audio (L) in Y-Pb-Pr 6b Audio (R) in Component 6c CVBS in 6d, e, f Component video in 7.
CLOCK & PHASE Adjustments Front control panel 15 150MT10P LMT Go to cover page Recover attention signals by pressing AUTO button for more than 10 seconds without video signal input. ATTENTION ATTENTION SIGNAL ON To Lock/Unlock OSD function The OSD function can be locked by pressing OK button for more than 10 seconds, the screen shows following windows for 3 seconds. Everytime when you press OK Or AUTO button, this message Appears On the screen automatically.
150MT10P LMT OSD Control structure Go to cover page The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments.
OSD Control structure In TV/Video Mode 17 150MT10P LMT Go to cover page
150MT10P LMT OSD Attention signals Go to cover page The monitor will detect various display situation automatically. When the monitor detects the problems, the screen will show the different warning signals to remind you what is happen to your monitor. NO VIDEO INPUT This screen appears if there is no video signal input. Please check that the signal cable is properly connected to the video card of PC and make sure PC is on.
Failure Mode of LCD panel 19 150MT10P LMT Go to cover page Quick reference for failure mode of LCD panel This page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the Mechanical instruction o n this manual to eliminate failure by replace LCD panel or backlight tubes. Failure description . Polarizer has bubbles Phenomenon Vertical block defect Polarizer has bubbles Vertical dim lines Foreign material inside polarizer.
150MT10P LMT Definition of Pixel Defects Go to cover page 0. General 3. Pixel Defect Tolerances This section explains the different types of pixel defects and defines acceptable defect levels of each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels.
Wiring Diagram 21 150MT10P LMT Go to cover page 1687 1995 1686 1211 1986 1371 3138 1921 1931 1351 J1 1942 1932
150MT10P LMT Mechanical instructions Go to cover page Condition Re-install the base - for VESA standard mounting applications - for optional bases replacement Remove the base 5) Push down the protective cover to mount it securely
Mechnical instructions 23 150MT10P LMT Go to cover page 1. Control panel bezel removal Using the Minus(-) driver to find the groove position between the front cabinet and the back cover on the downside of set as Fig.1 Fig. 1 Groove position Right side 2. Control panel Bezel removal asFig.2 Fig.2 control panel Top side 3.- Remove the connect 1995 - Remove the connect 1986 - Remove the L/R speaker connector Fig. 3 4.
150MT10P LMT Mechanical instructions Go to cover page Fig. 9 : 1.Remove 1921 connector in the audio PCB assy 2.Remove 1995 connector in the control PCB assy Fig. 6 : Removal LCD panel ,Remove 4 screws in the backcover Fig. 9 Fig. 6 Fig. 7 : Removal Audio PCB assy , Remove 4 screws in the LCD pannel A10 SSB Assy 3139 137 25771 Tuner function 3138 149 70531 Fig. 7 Inverter board 8238 27710891 Fig. 10 Mian board 3138 158 52661 Fig. 8 : After removing metal shield Service position Fig. 10 Fig.
Electrical instructions 25 150MT10P LMT Go to cover page PRESET VIDEO RESOLUTION 0. General When carry-out the electrical settings in many cases a video signal must be applied to the monitor. A computer with : - ATI VGA 1024 V6-1.04/PH BETA4 interface card - PGA 1024 (4822 212 30916), Mach 8. - PGA 1280 (4822 212 30917), Mach 32. - ATI GPT-1600 (4822 397 10065), Mach 64 (up to 107kHz) Factory preset video resolution Dot rate (MHz) H.freq (KHz) are used as the video signal source.
Electrical instructions 150MT10P LMT Go to cover page 2.3.2 Table2 for Europe and AP-multi Signal Distribution Table (PAL Cable) Frequency Carriers PRG CH Video TV System Pattern Sound 0 1 AU37 590.25MHz 595.75MHz PAL B(UK) Pure White 2 AU2 64.25MHz 69.75MHz PAL B(UK) Circle Pattern 3 E7 189.25MHz 194.75MHz PAL B (CCIR) Circle Pattern 4 G47 679.25MHz 684.75MHz PAL G (CCIR) Circle Pattern 5 I23 487.25MHz 493.75MHz PAL I (UK) Circle Pattern 6 E12 224.25MHz 229.
Electrical instructions 5.1.2 White balance adjustment (B) A ) GENERAL SET-UP Equipment Requirements : Colour analyzer. B) INPUT REQUIREMENTS Input Signal Type : RF signal, modulated with white Pattern Input Signal Strength : >= 1mV rms (60 dBuV) terminal voltage.
Factory Adjustment 150MT10P LMT Go to cover page Factory Mode Adjustment Entering Factory Adjustment Menu Push OK & buttons then power on the monitor, release them after picture display normally. Press OK button to bring up OSD menu of factory mode as shown below. LCD TV V1.28 20011030 Use button to select factory adjustment indication (for example: LCD TV V1.28 20011030, which is the entrance of the factory adjustment menu, press OK button to access it. The window shows as below.
Safety Test Requirements All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both Hipot and Ground Continuity testing. HI-POT TEST INSTRUCTION 1. Application requirements 1.1 All mains operated products must pass the Hi-Pot test as described in this instruction. 1.2 This test must be performed again after the covers have been refitted following the repair, inspection or modification of the product. 29 150MT10P LMT Go to cover page 3.
150MT10P LMT Go to cover page DDC Instructions General DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed. It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.
DDC Instructions (Continued) 150MT10P LMT 31 Go to cover page Configuration and procedure 3. At the submenu, type the letter of your computer's floppy disk drive followed by :EDID301 (for example, A:\EDID301, as shown in Fig. 5). There are 2 chips contained OSD string, serial number..etc on the circuit board, main EEPROM (7402, 32k) which storage all factory settings, OSD string.DDC IC (7202) which storage 128byte EDID data (serial number ..etc.).
DDC Instructions (Continued) 150MT10P LMT Go to cover page Re-programming Analog DDC IC Step 3: Modify DDC data (verify EDID version, week, year) Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10 1. PC Click (new function) icon from the tool bar, bring up Step 1 of 9 as shown in Fig. 14 . EDID30 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9. Fig.
DDC Instructions (Continued) 150MT10P LMT 33 Go to cover page 3. Click Next , bring up Fig. 17. 6. Click Next , bring up Fig. 20. Fig. 17 Fig. 20 7. 4. Click Next , bring up Fig. 21. Click Next , bring up Fig. 18. Fig. 18 Fig. 21 PHILIPS 150MT 8. 5. Click Next , bring up Fig. 19. Click Next , bring up Fig. 22. - Fill out serial number. - Click Finish to exit the Step window. Fig. 22 Fig. 19 TY123456 Definition of Serial Number TY000105000001 Serial Number (U.S.
DDC Instructions (Continued) 150MT10P LMT Go to cover page Step 5: Access Factory Mode for DDC data writing Factory Mode: How to Get into Factory Mode Menu Step 8: Save DDC data Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below: 1. Push Menu " OK " & " ATUO " & " " buttons simultaneously untill picture comes on the screen. Press Menu " OK " button, bring up Factory mode indication as shown in Fig 23 .
DDC data of Analog THE DISPLAY DATA CHANNEL ( DDC 2B ) CONTENT (FOR 150MT10P/00C LCD Monitor / TV ) ********************************************************************** EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 0021 (HEX.) ID Serial Number : 1E240 (HEX.
Repair Tips 150MT10P LMT Go to cover page 0. Warning All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the unit via a wrist wrap with resistance. Keep components and tools also at the same potential ! 1. Servicing of SMDs (Surface Mounted Devices) 1.
Colour adjustment 37 150MT10P LMT Go to cover page LCD COLOUR ANALYZER - CA110 1. SUMMARY The LCD Colour Analyzer CA-110 was designed to upgrade the white-balanceprocess on production lines for colour LCD televisions and computer colour LCD panels in the colour LCD industry. The CA-110 consists of a main unit and a measuring probe. The measuring probe utilizes an optical system suitable for measurement of colour LCDs and is equipped with a viewfinder to verify the area to be measured. 2.
150MT10P LMT Go to cover page Colour Adjustment
Colour adjustment 39 150MT10P LMT Go to cover page ZERO CALIBRATION Zero calibration is performed to determine the output of the measuring probe when no light reaches the sensor and to set this as the zero point to which all other measurements are referenced. Zero calibration must be performed after the POWER switch has been set ON brfore taking any measurements. To perform zero calibration : * Before performing zero calibration, check that the measuring probe has been connected to probe connector P1.
Colour Adjustment 150MT10P LMT Go to cover page SETTING MEASUREMENT AREA I I I Measurement areas of o 25mm and o 50mm can be selected by extending or retracting the lens barrel. The o 25mm measurement area can be used for measuring LCDs with 2 - inch or greater diagonals: the o50mm measurement area can be used for measuring LCDs with 4 inch or greater diagonals. I Set the measurement area : Using a slotted screwdriver, loosen the lens - barrel locking screw.
Colour adjustment 41 150MT10P LMT Go to cover page SETTING MEASUREMENT DISTANCE The measurement distance (the distance from the front of the measuring probe's lens barrel to the display surface of the LCD ) should be set using a ruler according to the procedure below. 1. Mount the measuring probe on a tripod or other stand and mount the LCD on a suitable stand. 2.
Colour Adjustment 150MT10P LMT Go to cover page White Balance Adjustment Alignment procedure 1. Turn on 150P2E LCD monitor. 2. Turn on the Timing/Pattern generator. See Fig. 1 Setting generator to provide CROSS-Hatch pattern at Resolution : 1024 x 768 Timing : H= 48 KHz V= 60 Hz 3. Preset LCD colour Analyzer CA-110 - Remove the lens protective cover of probe CA-A30. - Set Measuring/viewing selector to Measuring position for reset analyzer. (Zero calibration) as Fig.
Block Diagram Control Panel Diagram and C.B.A.
150MT10P LMT Scaler Board C.B.A.
Hmc.map Scaler Board (C.B.
150MT10P LMT Conjunction Diagram Phone Jack PCB Phone Jack C.B.
Sound Board (C.B.
Schematic Diagram (Conjunction PCB) Schematic Diagram (Video Decorder) 150MT10P LMT Go to cover page 1.6 1.5 2.5 8 9 2.5 10 11 12 0.8 2 1 2.1 0.6 4 3 5 0.5 6 3.2 7 1.3 0.8 13 1.6 14 0.8 15 1 7403-C 4 7406-B 7 7408-C 10 3423-5 13 3458-8 16 3461-7 19 3462-6 19 0.5 V/div 10 mS/div 0.2VV/div 10mS/div 0.
Schematic Diagram (MCU) 49 150MT10P LMT Go to cover page 9.8 3.2 1.0 1.3 1.4 1.4 1.1 1.4 2.6 1.5 1.5 1.2 1.5 1.3 2.6 2.0 2.5 1.3 1.3 1.4 1.4 1.1 1.4 2.7 1.4 2.0 1.5 1.5 1.1 1.5 1.3 2.6 2.5 2.8 2.8 2.8 2.8 1.7 3.0 3.2 9.8 3.9 3.1 3.2 3.0 3.0 3.0 4.8 3.1 4.
Waveforms Schematic Diagram (Scaler) 150MT10P LMT Go to cover page 2.5 3.2 3.2 3.2 23 22 1.7 1.1 1.1 1.3 26 27 28 1.2 1.3 1.4 1.2 29 30 24 32 33 1.2 1.4 1.3 1.2 34 35 36 37 1.5 1.1 38 39 40 41 1.4 1.3 1.4 1.4 42 43 44 45 1.5 0.8 46 47 48 1.4 1.4 1.4 1.4 49 50 51 52 3.2 25 3.2 4.5 4.5 3.2 3.2 3.2 4.5 1.4 1.4 1.1 4.5 4.5 1.4 1.4 1.4 1.4 3.2 1.4 1.4 0.9 1.4 1.4 1.4 1.
Schematic Diagram (Video I/O) 150MT10P LMT 51 Go to cover page
150MT10P LMT Go to cover page Inverter Diagram Inverter layout drawings
Exploded View 3138 154 04101 Side cover - L 44 150MT10P LMT 53 Go to cover page 3138 154 04081 Back cover 41 45 3138 154 04111 Side cover - R 71 3138 151 31751 Main shield-PAL 3138 151 60741 BASE 61 1053 3138 158 52301 Audio PCB ASSY 3138 158 52261 Main PCB ASSY 1052 51 3138 151 31741 Main metal frame-PAL 1054 3138 158 52311 Conjunction PCB 3138 151 31741 Main metal frame-PAL 1068 3138 158 51981 Phone jack pcb assy 1055 3138 157 51981 Bezel Assy 1 1057 8238 277 09841 LCD panel CLAA150X 3138 15
150MT10P LMT Recommended Parts List Go to cover page Model: 150MT10P/00C/74C Item Code Number 1 313815751981 2 313815752001 3 313815751991 4 313815752011 6 313815404251 30 313815552931 31 313815404071 41 313815404081 44 313815404101 45 313815404111 61 313815160741 81 313815404091 82 313815404211 450 313815631481 451 313815631451 452 313815631461 453 313815620612 601 313811703661 1052 313815852261 1052 313815853751 1060 313812874931 1060 313812874901 1065 929900010137 1066 313922889481 1066 31392288947
150MT10P LMT Go to cover page Spare Parts List MODEL :150MT10P/00C 0001 0002 0003 0004 0006 0007 0009 0010 0013 0014 0016 0019 0020 0021 0022 0023 0024 0025 0026 0027 0028 0030 0031 0039 0041 0044 0045 0045 0046 0046 0047 0051 0052 0053 0054 0057 0061 0062 0063 0064 0065 0066 0067 0068 0069 0071 0072 0081 0082 0083 0084 0085 0086 0087 0089 0129 0131 0133 0139 0140 0141 0141 0143 0161 0171 0172 0181 0182 0183 0191 0201 0211 0212 0213 0214 0270 0271 0272 0273 0274 0275 0276 0277 0281 0281 0281 0281 0282
Spare Parts List 150MT10P LMT Go to cover page 2371 2372 2373 2374 2375 2376 2377 2378 2379 2380 2381 2382 2383 2384 2385 2386 2387 2388 2389 2390 2391 2392 2393 2394 2395 2396 2397 2401 2402 2403 2405 2406 2407 2408 2409 2411 2412 2413 2414 2415 2416 2417 2418 2419 2421 2422 2426 2427 2428 2429 2431 2432 2433 2435 2436 2437 2438 2441 2443 2446 2451 2452 2453 2456 2457 2458 2459 2461 2462 2463 2465 2466 2467 2468 2469 2471 2472 2473 2475 2476 2477 2478 2479 2481 2482 2483 2485 2486 2487 2488 2489 2491
Spare Parts List 3388 3389 3390 3391 3392 3393 3394 3395 3401 3402 3405 3406 3407 3408 3409 3410 3411 3412 3415 3416 3417 3418 3419 3420 3422 3423 3425 3426 3427 3428 3429 3430 3431 3432 3433 3436 3437 3438 3439 3441 3442 3445 3446 3447 3448 3449 3450 3453 3454 3455 3456 3457 3458 3459 3461 3462 3463 3465 3466 3467 3468 3469 3471 3472 3473 3475 3476 3477 3481 3482 3601 3602 3603 3605 3606 3607 3608 3609 3611 3612 3613 3615 3616 3617 3618 3619 3621 3622 3623 3625 3626 3627 3628 3631 3632 3633 3635 23500351
150MT10P LMT Go to cover page 7052 7201 7202 7203 7205 7206 7301 7321 7322 7323 7331 7351 7361 7362 7363 7401 7402 7403 7405 7406 7407 7408 7409 7410 7411 7412 7413 7415 7431 7451 7471 7621 7901 7902 7911 7912 7921 7931 7932 7935 7936 7937 7991 7992 7996 7997 932216732668 935256600112 932212662682 932217680682 935218650118 932216554668 932214526668 935260739118 932217743685 933714830653 823827709181 933967310685 932216677682 932216677682 932216677682 935267395518 933967310685 933967310685 933967310685
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION GENERAL PRODUCT SPECIFICATION . 15 LCD monitor with TV function. . PC 15 pins D-SUB analog interface. . TV Tuner, S-Video with L/R RCA Audio in. SCART (RGB, AV) input interface ( for Europe model ) Cinch input (YUV, AV) input interface ( for NAFTA , AP model ) . PC audio line in, and headphone out interface . L/R audio line output. . NTSC, PAL, SECAM TV system. . 100 Pages Teletext (Europe) and Closed caption, V-chip(NAFTA) .
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page CONTENTS 1.0 Foreword 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 Product profile LCD Scanning frequencies Video dot rate Power input Power consumption Dimensions Weight Functions Ambient temperature Regulatory compliance 3.0 Electrical characteristics 3.1 Interface signals cables 3.2 User interface 3.2.1 Front control panel 3.2.2 Front control panel definition 3.2.3 PC signal control via front key 3.2.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 4.4 4.4.1 4.5 4.6 4.7 4.8 Image size Actual display size Brightness uniformity PC white color adjustment TV white color adjustment TV picture centering 5.0 5.1 5.2 5.3 5.4 5.4.1 5.4.2 Mechanical characteristics Controls Unit dimension / weight Tilt and swivel base Transportation packages Shipping dimension / weight Block unit / palletization 6.0 6.1 6.2 6.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 1.0 FOREWORD This specification describes a 15" XGA multiscan color TFT LCD Monitor/TV with max. resolution up to 1024x768/75Hz non-interlaced. 2.0 PRODUCT PROFILE Philips 15 TFT LCD monitor/TV can connect to PC with analog D-SUB, and has TV, Video interface with integrated base. Meet word wide five major TV system: West Europe, East Europe, NAFTA, Asia Pacific and China. 2.1 LCD Type NR. : CLAA150XE01 Dimensions : 15 Pitch ( mm ) : 0.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 3.0 Electrical characteristics 3.1 Interface signals cables VGA Interface Cable (for all model) Length : 1.8 M +/- 50 mm Stereo RCA audio cable (option) Length : 1.5 M +/- 50 mm S-video cable (option) Length : 1.5 M +/- 50 mm SCART cable (option) Length : 1.5 M +/- 50 mm YCbCr cable (option ) Length : 1.5M +/- 50 mm AV cable (option) Length : 1.5M +/- 50 mm Mini Jack stereo cable(for all model) Length : 1.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 3.1 User interface On screen display user control via front keypad (PC and TV OSD) and remote control for TV. 3.2.1 Front control panel Front Control Panel PC Video Source PIP Menu Power - PC TV - TV/Video Auto IR Power Receiv LED er It s Top/Down LED, will be switched by pushing P T C V B tt 15"TFT XGA LCD Monitor / TV 2001-10-02 + TYPE : 150MT10P/00C BRAND : PHILIPS 8639 000 11717 36 K.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 3.2.2 Front control panel definition : PIP : PIP enable/disable and size select (active in PC mode). PC/TV : PC/TV select key. PC/TV LED: PC/TV status. Video Source : AV source select key. Power: Power switch. Power LED: Normal operationgreen. Sleeping modegreen with blanking. IR receiver. -CH-: Channel up and down, and OSD cursor up and down.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 3.2.3 PC Signal control via front keyboard: Language : ENGLISH , ESPANOL , FRANCAIS , DEUTSCH , ITALIANO Adjust position: H-position, V-position. Brightness and contrast: Lamps brightness and PC graphic contrast adjustment. Video noise : Phase adjustment, Clock adjustment Adjust color : Original panel color , 9300K for CAD/CAM use 6500k for image management, User color red, green and blue color adjustable.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 3.2.4 TV Signal control via front keyboard and RC control: 3.2.4.1 Remote control function 1. PIP On/Off/Size 2. PIP Position 3. AV source 4. Digit(0-9) 5. Smart Sound 6. Menu 7. Cursor move 8. Volume + / 9. Teletext access 10. On/Off Teletext 11. Mix 12. Reveal/Conceal 13. I-II 1 2 3 4 5 6 7 14 15 16 8 9 10 11 12 13 19 20 21 22 23 24 14. standby ( Power ON/Off in US) Standby 15. Timer 16. Program List 17. Smart Picture 18. PC/TV 19.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 3.2.4.2 Remote control key definition 1. PIP On/Off and size 2. PIP position 3. Press source select key to select EXT, S-Video and TV(AV,CVI, S-Video and TV for Naft nd 4. Digital number: For direct access to programs .For a 2 digit program number, the 2 digit must be entered before the dash disappears. 5.Smart sound: To access a series of settings: VOICE, MUSIC, THEATRE and return to PERSONAL 6. Menu: To display or exit from the menus 7.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION timer. Hold down for 5 seconds to permanently display the programme number on the screen. The volume level and the smart control adjustments are then displayed each time they are used. 23. Alternate channel: To access the previously viewed program 24. Close caption: Closed caption selection. (disable in EE/WE/AP/CN) 3.2.4.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page Sort the programs For Europe: 1. Press the menu key. The main menu is displayed. 2 Select INSTALL (down key), then press right key. The INSTALL menu appears. 3 Using the down key, select SORT then press right key. The SORT menu appears. The FROM option is activated. Note: this menu works as follows: Change "FROM" (enter the current program number), "TO" (enter the new number), EXCHANGE numbers" (the operation is carried out). 4.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION Manual tuning For Europe: This menu allows you to store the programs one by one. 1. Press menu. 2. Select INSTALL (down), then press right. The INSTALL menu appears. 3. Select MANUAL STORE (down) then press right. The menu appears : 4. Press right to go to the SYSTEM menu.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page Automatic tuning For Europe: This menu allows you to automatically search for all the programs available in your region (or on your cable network). 1. First carry out operations 1to 8 above, then: 2 Press down once to select AUTO STORE then press right. The search begins. After several minutes, the INSTALL menu reappears automatically. 3.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION Manual tuning For Europe: This menu allows you to store the programs one by one. 1. Press menu. 2. Select INSTALL (down), then press right. The INSTALL menu appears. 3. Select MANUAL STORE (down) then press right. The menu appears : 4. Press right to go to the SYSTEM menu.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page Program Name You may, if you wish, give a name to the first 40 programs (from 1 to 40). 1. Press menu. 2. Select INSTALL (down), then press right. The INSTALL menu appears. 3. Press down 5 times to select NAME (concealed at the bottom of the screen), then press right. The menu appears : 4. Select the program you wish to name using the keys 0.9 or - P +.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION Adjust the picture 1. Press menu then right. The PICTURE menu appears : 2. Use up down keys to select a setting and left right keys to adjust. Note: the menu is a scroll-down menu. Keep the key down held down to access the settings hidden at the bottom of the screen. 3 Once the necessary adjustments have been made, select the option STORE and press right to store them. 4 To exit from the menus, press menu.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page Adjust the sound 1 Press menu, select the SOUND function (down key) and press right key. The SOUND menu appears : 2. Use up down keys to select a setting and left right keys to adjust. Note: to access the AVL setting (hidden at the bottom of the screen) hold down down key. 3. Once the necessary adjustments have been made, select the option STORE and press right to store them. 4. To exit from the menus, press OSD key.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION Timer Function This menu allows you to use your TV as an alarm clock. 1. Press menu. 2 Select FEATURES (down) and press right twice. The TIMER menu appears : 3. Press right to enter and exit the sub-menus and use keys up down to adjust: 4. TIME: enter current time. Note: the time is updated automatically each time the set is switched on using teletext information taken from program 1.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page Locking Set For Europe: You can bar access to certain programs or completely lock the set by locking the keys. Locking programs 1. Press menu. 2. Select FEATURES (down) and press right. 3. Select PARENTAL. CONT. (down) and press right. 4. Enter your confidential access code. The first time, enter the code 0711 then confirm by re-entering 0711.The menu appears. 5. Press right to go into the menu. 6.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 1. Press menu, select FEATURES (down) and press right. 2. Select CHILD LOCK (down) and press right to set the lock to ON. 3. Switch off the set and put the remote control out of sight. The set cannot be used (it can only be switched on using the remote control). 4. To cancel: switch CHILD LOCK to OFF. For Nafta: The universal code is same as Europe . Use auto lock function to select V-chip function. Use Closed Cap to select caption mode. 3.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page MODE NO. RESOLUTION 1 640 x 350 *2 720 x 400 *3 640 x 480 4 640x480 Dot clock(MHz) 25.175 28.321 25.175 30.240 fh A ( us ) B ( us ) C ( us ) D ( us ) E ( us ) 31.469kHz 31.78(800 dots) 3.813(96 dots) 1.907(48 dots) 25.42(640 dots) 0.636(16 dots) 31.469kHz 31.78(900dots) 3.813(108dots) 1.907(54dots) 25.42(720dots) 0.636(18dots) 31.469kHz 31.778 (800 dots) 3.813 ( 96 dots) 1.907 ( 48 dots) 25.422 (640 dots) 0.636 ( 16 dots) 35.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION MODE NO. RESOLUTION 9 800 x 600 * 10 800 x 600 11 832 x 624 * 12 1024 x 768 Dot clock(MHz) 50.000 49.500 57.280 65.000 fh A ( us ) B ( us ) C ( us ) D ( us ) E ( us ) 48.077kHz 20.80 (1040dots) 2.400 ( 120 dots) 1.280 ( 64 dots) 16.00 ( 800 dots) 1.120 ( 56 dots) 46.875kHz 21.333 (1056dots) 1.616 ( 80 dots) 3.232 ( 160 dots) 16.162 ( 800 dots) 0.323 ( 16 dots) 49.722kHz 20.11 (1152dots) 1.117 ( 64 dots) 3.911 ( 224 dots) 14.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 3.3.1.3 Horizontal scanning Sync polarity Scanning frequency : Positive or Negative : 30 - 61 KHz 3.3.1.4 Vertical scanning Sync polarity Scanning frequency : Positive or Negative : 56 - 75 Hz 15"TFT XGA LCD Monitor / TV 2001-10-02 TYPE : 150MT10P/00C BRAND : PHILIPS 8639 000 11717 36 K.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 3.3.2 TV Interface Color system: NTSC PAL SECAM White point : Normal(Natural) : x=295+/-20 y=315 +/-20 Warm(Soft) Cool(Rich) SOUND POWER OUTPUTS : - Stereo : 2 x 2.5 Watts, SOUND CONTROLS : - Volume - Mute - Treble - Bass - Balance - Smart sound - AVL : - SOUND MUTE : When no video recognition on terrestrial tuner signal the sound must be muted.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page TELETEXT ( For Europe, AP) 100 pages BASIC : - TXT on/off - Hold (Stop acquisition) - Double height - Reveal - Subcode (Clock/time) - Mix - Cancel/recall - Index - Close Caption, V-chip ( For Nafta) - CC-1 .. CC-4 decoding and display - TXT1..
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 4.0 Visual characteristics 4.1 Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal : As defined in 3.3.1.2, 1024 x 768 non-interlaced mode (60.023 KHz), signal sources must have 75 ohm output impedance. (2) Luminance setting : controls to be set to 250 Nits with full screen 100 % duty cycle white signal.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 3.4 Power input connection Power cord length : 1.8 M Power cord type : 3 leads power cord with protective earth plug. Power adapter: +12V +/- 1V 4500mA 3.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 4.0 Visual characteristics 4.1 Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal : As defined in 3.3.1.2, 1024 x 768 non-interlaced mode (60.023 KHz), signal sources must have 75 ohm output impedance. (2) Luminance setting : controls to be set to 250 Nits with full screen 100 % duty cycle white signal.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 4.3 4.4 4.4.1 4.5 Brightness: >250 nits at maximum contrast and Brightness. (at center of the screen, Fig. 1 ) Image size Actual display size 304.1x228.1mm Brightness uniformity Set contrast at 100% and turn the brightness to Max.(At original color) Apply the Fig 1, it should comply with the following formula: Minimum luminance of five points (brightness) > 80% Maximum luminance of five points (brightness) 4.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 4.7 TV White color adjustment There is one factory preset white color x=295+/-20 y=315 +/-20 for TV RF signal. Use FLUKE54200 color temp pattern, with TV smart setting set at natural ( movies at Nafta) mode. And color setting is normal. Use The 1931 CIE Chromaticity (color triangle) diagram (x,y) coordinate for the screen center should be: x=295+/-20 y=315 +/-20 4.8 TV picture centering.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 5.0 Mechanical characteristics 5.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 5.4.2 Block unit / Palletization (Air shipment) layers/block 6 6.0 6.1 sets/layer 4 sets/block unit 24 Environmental characteristics The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page 6.2 Transportation tests Standard Philips UAN-D1400 Height Drop Sequence Test NSTA 76 cm 76 cm 1 corner 1 corner 3 faces 3 edge (-10deg C x 16 hrs) (roon temp) 6 face Electrical function ok Test Mechanical function ok Result No serious damage on set appearance (room temp./-10 c, humidity 70 %) (1) PACKAGING Sequence 5-200 Hz , 0.73 G , 30 min. for Each axis (2) OPERATING Vibration Test 10-50-10 Hz , 0.35 mm , 30 min.
150MT10P LMT Go to cover page GENERAL PRODUCT SPECIFICATION 6.3 Display disturbances from external environment According to IEC 801-2 for ESD disturbances 7.0 Reliability 7.1 Mean Time Between Failures System MTBF (Excluding the LCD panel and CCFL) : 50,000 hrs CCFL MTBF : 50,000 hrs 8.0 8.1 Quality assurance requirements Acceptance test according to MIL-STD-105D Control II level AQL : 0.65 (major) 2.5 (minor) (please also refer to annual quality agreement) 9.
150MT10P LMT GENERAL PRODUCT SPECIFICATION Go to cover page Fig 1: Brightness and Uniformity measure points b H/1 0 H/2 9H /10 b a a 1 V/ 10 V/2 2 V 5 3 9V/ 10 4 a a b b H 15"TFT XGA LCD Monitor / TV 2001-10-02 TYPE : 150MT10P/00C BRAND : PHILIPS 8639 000 11717 36 K.
