Manual file:///D|/TV/english/150mt/Manual.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.
Safety & Troubleshooting ● Avoid exposure to heat and extreme cold Do not store or use the product in locations exposed to heat, direct sunlight or extreme cold. Avoid moving the product between locations with large temperature differences. Choose a site that falls within the following temperature and humidity ranges. ❍ Temperature: 5-35°C 41-95°F ● Humidity: 20-80% RH Do not subject the product to severe vibration or high impact conditions. Do not place the product inside a car boot.
About This Manual About This Manual About This Guide • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor TV. It describes the features, setup, operation and other important information. It includes the following sections: ● ● Safety and Troubleshooting Information provides tips and solutions for common problems as well as other related information you may need.
About This Manual CAUTION: This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data. WARNING: This icon indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific presentation of the warning is mandated by the relevant regulatory authority. RETURN TO TOP OF THE PAGE ©2001 Koninklijke Philips Electronics N.V.
Product Information Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Physical Function Product Features 150MT ● ● ● ● ● Multi video input allowing display of PC, DVD, VCD, VCR and TV Picture in Picture (PIP) function Super-high brightness and fast response time AUTO adjustment optimizes picture quality 100-page Teletext (in areas where teletext serv
Product Information • Input impedance - Video 75 ohm - Sync 2K ohm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync • Sync polarities Positive and negative • Input Frequency XGA Hsync SVGA Hsync VGA Hsync • Video interface D-sub, S-Video, TV-RF, SCART (Europe) or composite and components video (others) 48- 61 kHz, Vsync 60 - 75 Hz (N.I.) 35- 50 kHz, Vsync 56 - 75 Hz (N.I.) 31- 38 kHz, Vsync 60 - 75 Hz (N.I.
Product Information Resolution & Preset Modes • Maximum 1024 x 768 at 75Hz • Recommended 1024 x 768 at 60Hz 14 user definable modes 14 factory preset modes: H. freq (kHz) Resolution V. freq (Hz) 31.469 640*350 70.086 31.469 720*400 70.087 31.469 640*480 59.940 35.000 640*480 67.000 37.861 640*480 72.809 37.500 640*480 75.000 35.156 800*600 56.250 37.879 800*600 60.317 48.077 800*600 72.188 46.875 800*600 75.000 49.700 832*624 75.000 48.363 1024*768 60.004 56.
Product Information VESA Mode Video H-sync V-sync Power Used LED color ON Active Yes Yes 48W (typ.) Green OFF Blanked No No < 2W Flashing Green This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) 391 x 366 x 200 mm (incl. Pedestal) • Weight 5.
Product Information Pin Assignment No. Pin Assignment No. 1 2 Red video input Green video input 9 10 DDC +5V Logic ground Identical output - connected to pin 10 3 Blue video input 11 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 6 Ground Red video ground 13 14 H. Sync / H+V V. Sync 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Product Views Follow the links to see various views of the monitor and its components.
Product Information Tilt RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/product/product.
Installing your LCD Monitor/TV Installing your LCD Monitor/TV Front View Product Description • Connecting to Your PC, TV antenna, DVD/VCR etc.
Installing your LCD Monitor/TV 6 Automatically adjust the H/V position, phase and clock setting 7 Increase or decrease the level of audio volume or move up or down the highlighted function in OSD 8 MENU OK Open the OSD and select the highlighted function RETURN TO TOP OF THE PAGE Side View 1. Headphone Jack 2. LINE OUT Jack file:///D|/TV/english/150mt/install/install.
Installing your LCD Monitor/TV RETURN TO TOP OF THE PAGE Rear View file:///D|/TV/english/150mt/install/install.
Installing your LCD Monitor/TV (Europe) 1 DC 12V DC 12V power in 2 PC - Video D-Sub input 3 4 PC - Audio S-VIDEO (L) PC Stereo input AV audio (L) S-VIDEO (R) AV audio (R) 5 S-VIDEO S-VIDEO in 6 EXTERNAL/ EURO-AV SCART connection (for Europe only) 7 75 TV Antenna or CATV cable in RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/install/install.
Installing your LCD Monitor/TV (North America and Asia Pacific) file:///D|/TV/english/150mt/install/install.
Installing your LCD Monitor/TV 1 DC 12V DC 12V power in 2 PC - Video D-Sub input 3 4 PC - Audio S-VIDEO (L) PC Stereo input AV audio (L) S-VIDEO (R) AV audio (R) 5 S-VIDEO S-VIDEO in 6 L R - AV IN Y-Pb-Pr Component 6a Audio (L) in 6b Audio (R) in 6f CVBS in 6c, d, e Component video in 7 TV Antenna or CATV cable in 75 RETURN TO TOP OF THE PAGE Optimizing Performance ● For best performance, ensure that your display settings are set at 1024x768@60Hz (for 15") or 1280x1024, 60Hz (for 18")
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree Description of the On Screen Display What is the On-Screen Display? This is a feature offered by all Philips LCD monitors/TVs. It allows an end user to adjust screen performance of monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when the user is operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display file:///D|/TV/english/150mt/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE - In TV/Video Mode: (For Europe) file:///D|/TV/english/150mt/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE (For Asia Pacific) file:///D|/TV/english/150mt/osd/osddesc.
On-Screen Display file:///D|/TV/english/150mt/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE (For NTSC system: North America, Philippine, Taiwan and Korea) file:///D|/TV/english/150mt/osd/osddesc.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/osd/osddesc.
TV Control TV Control Using your Remote Control • Using the Teletext • Using the Programme Listing • Using Other Menu: PAL System - Europe • PAL System - Asia • NTSC System Using your Remote Control (For PAL system: Europe and Asia Pacific) file:///D|/TV/english/150mt/osd/tv_control.
TV Control 1 PIP On/Off, Size To activate or close the 'Picture in Picture' function in PC mode and to enlarge or reduce the PIP window size using the same button 2 PIP Shift To change 'Picture in Picture' window position in PC mode ● To select TV/Video sources If using TV 'STANDBY', press this button to return to 'ON' 3 AV source 4 Smart sound controls To access a series of settings: VOICE, MUSIC, THEATRE and PERSONAL 5 Menu To turn on or off the OSD (On-Screen Display) To return to last ite
TV Control ● 10 Sound mode ● 11 To switch from STEREO to MONO or to choose between Dual I and Dual II for bilingual transmissions. For TV sets fitted with NICAM reception, depending on the transmission, you can switch from NICAM STEREO to MONO or choose between NICAM DUAL I, NICAM DUAL II and MONO. If using Teletext, press this button to display dual pages on screen. Previous programme To access the last programme viewed.
TV Control 18 19 Standby To set the TV temporarily to standby mode. To switch on the TV set, press Programme button (p -, +), any digit between 0 and 9 or AV source button (The green light indicator flickers when set is in standby mode) Sleep timer To select the period of time after which the set will switch automatically to standby mode (up to 240 minutes) (For NTSC system: North America, Philippine, Taiwan and Korea) file:///D|/TV/english/150mt/osd/tv_control.
TV Control 1 PIP On/Off, Size To activate or close 'Picture in Picture' function in PC mode and to enlarge or reduce the PIP window size using the same button 2 PIP Shift To change 'Picture in Picture' window position in PC mode 3 AV source To select TV/Video sources 4 Smart sound controls To access a series of settings: VOICE, MUSIC, THEATRE and PERSONAL 5 Menu To turn on or off the OSD (On-Screen Display) To return to last item in OSD & clear menu from screen 6 Cursor To move the cursor
TV Control 12 Selecting TV programmes To move up or down a programme. The number, (the name) and the sound mode are displayed for a few seconds. For some TV programmes the title of the programme appears at the bottom of the screen. 13 PC/TV mode selection To select TV or PC mode on and switch 14 Smart picture controls To select your desired picture setting from 5 settings: MOVIES, SPORTS, WEAK SIGNAL, MULTIMEDIA and PERSONAL. Numerical keys For direct access to channel.
TV Control On/Off Teletext 1 Display or exit Teletext. The main index page presents a list of subjects to which you have access. Each subject has a corresponding page number (always 3 digits). Note: If selected TV channel does not broadcast Teletext, P100 is displayed and the screen remains black. Exit Teletext mode and choose another TV channel. Selecting a Teletext page 2 Accessing a Teletext page 3 file:///D|/TV/english/150mt/osd/tv_control.
TV Control Direct Access to an item or 4 corresponding pages The 4-colour buttons allow you to access directly an item or corresponding pages. RETURN TO TOP OF THE PAGE Press button Result on Screen 5 Allows you to superimpose the Teletext page over the TV programme. Press the button a second time to return to Teletext page only. 6 Press the button once to Reveal/Conceal reveal hidden information (solutions to puzzles, riddles, etc.). Press the button a second time to conceal information.
TV Control Hold 9 Main Index 10 In 'Dual pages' mode, the HOLD button enables you to hold a page on one side and activate the page on the other side which can be scrolled to more pages by pressing the cursor down or up. To switch the holding status to the page on the other side, press the HOLD button again. Press the button to return to the main index (generally on page 100).
TV Control 1. Display the list of installed pro-grammes. The current channel is highlighted. 2. Run through the programme list and highlight the channel number you want to view. 3. Activate the channel you have selected. 4. Exit menu from screen or wait for the menu to time out and disappear from screen. RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/osd/tv_control.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey LATIN AMERICA: Antilles • Argentina • Brasil • Chile • Colombia • Mexico • Paraguay • Peru • Uruguay • Vene
Download and Print Download and Print Installing your LCD monitor driver • Download and Printing Instructions • Installing FPadjust Program Installing Your LCD monitor driver System requirements: ● ● PC running Windows 95, Windows 98, Windows 2000 , Windows Me, Windows XP or later Find your driver ".inf/.icm/.cat" at : /PC/drivers/ Read the "Driver_install02.txt" file before installing. This page provides an option to read the manual in .pdf format.
Download and Print Printing instructions: To print the manual: 1. With the manual file open, follow your printer's instructions and print the pages you need. RETURN TO TOP OF THE PAGE Installing FPadjust Program The FP Adjust program generates alignment patterns which will help you adjust monitor settings such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL POSITION, PHASE and CLOCK.
FAQs (Frequently Asked Questions) FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQs • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I install my monitor what should I do if the screen shows 'Cannot display this video mode'? A: Recommended video mode for Philips 15": 1024x768 @60Hz / Philips 18" 1280x1024@60Hz.
FAQs (Frequently Asked Questions) 30~61kHz and Vertical refresh rate 56~75Hz. However, users of monitors (of all brands, including Philips) may encounter certain limitations when viewing Microsoft Windows on a monitor operating at 75Hz with Horizontal Frequency 30~61kHz. To serve specific needs on 75Hz, Philips provides a special driver which can work for this. This special information file is now available at website www.p4c.philips.
FAQs (Frequently Asked Questions) Q: Will the LCD screen be resistant to scratches? A: A protective coating is applied to the surface of the LCD, which is durable to a certain extent (approximately up to the hardness of a 2H pencil). In general, it is recommended that the panel surface is not subjected to any excessive shocks or scratches. An optional protective cover with greater scratch resistance is also available. Q: How should I clean the LCD surface? A: For normal cleaning, use a clean, soft cloth.
FAQs (Frequently Asked Questions) place a shortcut on your desktop. 3. Run FPadjust by double clicking the shortcut. Follow the instructions step by step to optimise image performance with your system's video controller. Q: How do LCDs compare with CRTs in terms of radiation? A: Because LCDs do not use an electron gun they do not generate the same amount of radiation at the screen surface.
FAQs (Frequently Asked Questions) Q: What are S-VIDEO Signals? A: These are 2 separate Y/C video signals from the S-VIDEO and Hi-8 recording standards. The luminance signals Y (black and white) and chrominance signals C (colour) are recorded separately on the tape. This provides a better picture quality than is achieved with standard video (VHS and 8 mm) where the Y/C signals are combined to provide only one video signal.
FAQs (Frequently Asked Questions) frequently, improving the screen refresh time (your mouse pointer will appear to move more smoothly across the screen, for example). The passive matrix LCD has a grid of conductors with pixels located at each intersection in the grid. Q: How does a TFT LCD Panel work? A: On each column and row of the TFT LCD panel a data source drive and a gate drive and attached, respectively. The TFT drain of each cell is connected to the electrode.
FAQs (Frequently Asked Questions) varying the refraction ratio. IPS (In Plane Switching) or MVA (Multi Vertical Aligned) is also used to give a wider viewing angle. Q: Why is there no flicker on an LCD Monitor? A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from that of CRT monitor -- and it has no impact of the ease of viewing. Flickering in an LCD monitor relates to usually undetectable luminance caused by the difference between positive and negative voltage.
FAQs (Frequently Asked Questions) RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/safety/saf_faq.
Troubleshooting Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • TV and Audio Problems • Regulatory Information • Other Related Information This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Philips dealer.
Troubleshooting Vertical flicker appears ● ● Press the Auto button. Eliminate the vertical bars using the Clock Adjustment of VIDEO NOISE in OSD Main Controls. Horizontal flicker appears ● ● ● Adjust the contrast and brightness in OSD Main Controls. (The backlight of the product has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer.
Troubleshooting ● The proximity of mountains or high buildings may be responsible for ghost pictures, echoing or shadows. In this case, try manually adjusting your pictures: see 'fine tuning' or adjust the direction of the outside aerial. For Asia users in non-NTSC area: Does your antenna enable you to receive broadcasts in this frequency range (UHF or VHF band)? In the event of difficult reception (snowy pictures) switch the NR on the PICTURE menu to ON.
Regulatory Information Regulatory Information TCO '95 Information • TCO Environmental Requirements • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information consume an enormous amount of energy since they are often left running continuously. What does labelling involve? This product meets the requirements for the TCO'95 scheme which provides for international and environmental labelling of personal computers.
Regulatory Information RETURN TO TOP OF THE PAGE Environmental Requirements Brominated flame retardants Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances.
Regulatory Information The TCO'95 requirement: neither CFCs nor HCFCs may be used during the manufacturing of the product or its packaging. _____________________________ * Bio-accumulative is defined as substances which accumulate within living organisms ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
Regulatory Information Energy Star Declaration PHILIPS 150MT This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software.
Regulatory Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
Regulatory Information RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information Please note that this device has been approved for non-business purposes and may be used in any environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information RETURN TO TOP OF THE PAGE North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. file:///D|/TV/english/150mt/safety/regs/regulat.
Regulatory Information Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Regulatory Information Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Rot nicht auf dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelastung bei zu geringem Zeichenkontrast wären die Folge). Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70dB (A) oder weniger. ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND.
Regulatory Information have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere. How to connect a plug The wires in the mains lead are coloured in accordance with the following code: BLUE - "NEUTRAL" ("N") BROWN - "LIVE" ("L") GREEN & YELLOW - "EARTH" ("E") 1.
Other Related Information Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
Philips Pixel Defect Policy Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' LCD Panel Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practise stringent quality control.
Philips Pixel Defect Policy One lit red, green or blue sub pixel Two adjacent lit sub pixels: Three adjacent lit sub pixels - Red + Blue = Purple (one white pixel) - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Black Dot Defects appear as pixels or sub pixels that are always dark or 'off'.
Philips Pixel Defect Policy Total bright dot defects of all types 4 or fewer BLACK DOT DEFECTS 3 or fewer ACCEPTABLE LEVEL 150MT 180MT 1 dark sub pixel 4 or fewer 3 or fewer 2 adjacent dark sub pixels 2 or fewer 2 or fewer 3 adjacent dark sub pixels 0 0 15 mm or more 15 mm or more Black dot defects within 20 mm circle* 3 or fewer - Total black dot defects of all types 4 or fewer 3 or fewer MODEL Distance between two black dot defects* TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL Tota
Connecting to Your PC, TV Antenna, DVD/VCR etc. Connecting to Your PC, TV Antenna, DVD/VCR etc. Front View Product Description • Accessory Pack • Connecting to Your PC, TV Antenna, DVD/VCR etc. • Removing and Re-installing the Base • Basic Monitor TV Connections • Getting Started • Optimising Performance Accessory Pack Unpack all the parts. Power cable Remote control & batteries PC audio-in cable VGA signal cable file:///D|/TV/english/150mt/install/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Power adapter (Use only AC/DC adapter model SA165A-1250V-3P) E-DFU pack RETURN TO TOP OF THE PAGE Setting up and connecting your monitor/TV Ensure that the power to the monitor/TV is switched off before the installation. - Connecting the monitor/TV ● Connect the cables to the back of your monitor/TV by following step 1~7: (Europe) file:///D|/TV/english/150mt/install/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. (North America and Asia Pacific) RETURN TO TOP OF THE PAGE - Connect to PC ● ● Connect the cables to the back of your computer by following step 1~6 Switch on the power to your computer and monitor/TV and make sure the PC mode is ● selected ( ). If it is not, press the PC, TV/VIDEO selection button to select the PC mode. If your monitor displays the computer image the installation has been completed successfully.
Connecting to Your PC, TV Antenna, DVD/VCR etc. Installation section (Getting Started). RETURN TO TOP OF THE PAGE - Connect to DVD/VCD/VCR Connect to DVD/VCR/VCD through S-VIDEO ● Connect to DVD/VCR/VCD through S-VIDEO file:///D|/TV/english/150mt/install/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. ● Connect to DVD/VCR /VCD through SCART (for Europe) ● Connect to DVD/VCR /VCD through composite video (for AP and North America) file:///D|/TV/english/150mt/install/connect.
Connecting to Your PC, TV Antenna, DVD/VCR etc. ● Connect to DVD/VCR /VCD through component video (for AP and North America) RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/install/connect.
Removing and re-installing the base Removing and Re-installing the Base Front View Product Description • Accessory Pack • Connecting to Your PC, TV Antenna, DVD/VCR etc. • Basic Monitor TV Connections • Getting Started • Optimising Performance Removing and Re-installing the Base : Removing the base • Re-installing the base Condition: ● for VESA standard mounting applications ● for optional base replacement Removing the Base file:///D|/TV/english/150mt/install/base.
Removing and re-installing the base VESA Standard Holes (75mm x 75mm) RETURN TO TOP OF THE PAGE Re-installing the Base file:///D|/TV/english/150mt/install/base.
Removing and re-installing the base file:///D|/TV/english/150mt/install/base.
Removing and re-installing the base RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/install/base.
Basic Monitor/TV Connections Basic Monitor/TV Connections Front View Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc. • Removing and Re-installing the Base • Getting Started • Optimising Performance Basic Monitor/TV Connections: Cable TV • Antenna • Monitor TV to VCR Cable TV 1. If your Cable TV signal is a single, round cable (75 ohm), then you're ready to connect to the TV.
Basic Monitor/TV Connections 1. If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the TV. If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300 -to 75- ohm adapter. 2. Push the round end of the adapter (or antenna) onto the 75 (ohm) plug on the back of the TV. If the round end of the antenna wire is threaded, screw it down finger tight.
Basic Monitor/TV Connections 1. Connect your antenna or Cable TV signal to the IN FROM ANT(enna) plug on the VCR. 2. Connect the OUT TO TV plug on the VCR to the 75 ohm plug on the TV (connecting cable supplied with the VCR). 3. Refer to the owner's manual included with your VCR for other possible connections and TV/VCR operating details. RETURN TO TOP OF THE PAGE file:///D|/TV/english/150mt/install/basic.
Getting Started Getting Started Front View Product Description • Connecting to Your PC, TV Antenna, DVD/VCR etc. • Removing and Re-installing the Base • Basic Monitor TV Connections • Getting Started • Optimizing Performance Getting Started Use the information file ( .inf) for Windows 95/98/2000/Me/XP or later The built-in VESA DDC2B feature in Philips Monitors supports Plug & Play requirements for Windows 95/98/2000/Me/XP. This information file ( .
Getting Started 1. 2. 3. 4. 5. 6. 7. Start Windows Me Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. Double click on the 'Display' Icon. Select the 'Settings' tab then click on 'Advanced...'. Select 'Monitor' button, then click on 'Change...' button. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
Getting Started 8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button. 10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F: (CD-ROM Drive). 11. Click on the 'Open' button, then click the 'OK' button. 12. Select your monitor model and click on the 'Next' button.
Using other menus (PAL_Europe) Using Other Menus (PAL System - Europe) Using Your Remote Control • Using Other Menu: PAL System - Asia • NTSC System Install: Choosing a language and country • Automatic tuning • Manual tuning • Programme name Picture: Adjusting the picture Sound: Adjusting the sound Features: Timer function • Locking the set Using Other Menus (with remote control) Choosing a language and country 1. Press the MENU key to display the main menu. 2. Select INSTALL , then press .
Using other menus (PAL_Europe) 9. To exit from the menus, press . RETURN TO TOP OF THE PAGE Automatic tuning 1. First carry out operations 1 to 8 above, then: This menu allows you to automatically search for all the programmes available in your region (or on your cable network). 2. Press once to select AUTO STORE then press . The search begins. After several minutes, the INSTALL menu reappears automatically. 3.
Using other menus (PAL_Europe) This menu allows you to store the programmes one by one. 1. Press MENU. 2. Select INSTALL ( ), then press The INSTALL menu appears. 3. Select MANUAL STORE ( ) then press . The menu appears: . 4. Press to go to the SYSTEM menu. Use to choose EUROPE (automatic detection*) or manual detection with WEST EUR (standard BG reception), EAST EUR (standard DK reception), UK (standard I reception) or France (standards LL'). to exit from the menu.
Using other menus (PAL_Europe) 3. Using the key, select SORT then press . The SORT menu appears. The FROM option is activated. Note: this menu works as follows: Change 'FROM' (enter the current programme number), 'TO' (enter the new number), 'EXCHANGE numbers' (the operation is carried out). 1. Press MENU key. The main menu is displayed. 2. Select INSTALL ( ), then press The INSTALL menu appears. . 4. Select the programme you wish to renumber using keys or 0 to 9.
Using other menus (PAL_Europe) You may, if you wish, give a name to the first 40 programmes (from 1 to 40). 1. Press MENU. 2. Select INSTALL ( ), then press The INSTALL menu appears. 4. Select the programme you wish to name using the keys 0, 9 or - P +. Note: at the time of installation, the programmes are automatically named when the identification signal is transmitted. . 3. Press 5 items to select NAME (concealed at the bottom of the screen,) then press . The menu appears: 5.
Using other menus (PAL_Europe) Description of the settings: ● BRIGHTNESS: alters the brightness of the image. ● COLOUR: alters the colour intensity. ● CONTRAST: alters the variation between light and dark tones. ● SHARPNESS: alters the crispness of the image. ● STORE: stores the picture settings. ● COLOUR TEMP (colour temperature): adjusts the colour temperature of the picture. Three options are available here:COOL (blue white), NORMAL (balanced) or WARM (red white). ● INCR.
Using other menus (PAL_Europe) ● ● ● 2. Use keys to select a setting and keys to adjust. Note: to access the AVL setting (hidden at the bottom of the screen) hold down key. 3. Once the necessary adjustments have been made, select the STORE option to store them. and press 4. To exit from the menus, press programmes 1- 40 and the EXT sockets. STORE: stores the sound settings.
Using other menus (PAL_Europe) to enter and exit the 3. Press keys to sub-menus and use the adjust: 4. TIME: enter current time. This menu allows you to use your TV as an alarm clock. 1. Press MENU. 2. Select FEATURES ( ), and press twice. The TIMER menu appears: Note: the time is updated automatically each time the set is switched on using Tteletext information taken from programme 1. If programme 1 does not have Teletext, the update will not take place. 5. START TIME: enter the start time. 6.
Using other menus (PAL_Europe) 4. Enter your confidential access code. The first time, enter the code 0711 then confirm by re-entering 0711. The menu appears. 5. Press to go into the menu. You can bar access to certain programmes or completely lock the set by locking the keys. Locking programmes 1. Press MENU. 2. Select FEATURES ( ) and press . 3. Select PARENTAL. CONT. ( ) and press . keys to select the 6. Use the required programme and confirm with .
Using other menus (PAL_Asia 1) Using Other Menus (PAL System - Asia) Using your Remote Control • Using Other Menu: PAL System - Europe • NTSC System Install: Selecting the Menu Language and Automatic Tuning of Channels • Manual Tuning of Channels • Selecting the Colour/Sound System • Fine Tuning of Channels • Sorting of Channels • Editing of Channels • Naming of Channels Picture/Sound: Using the Picture/Sound Menu Features: Timer • Child Lock (Access/Change Code) • Activating the Child Lock (Lock Channel)
Using other menus (PAL_Asia 1) screen. RETURN TO TOP OF THE PAGE Manual Tuning of Channels 1. Press the MENU key to display the main menu. 2. Press the button repeatedly until INSTALL is selected. 3. Press the button to enter INSTALL menu. Manual tuning allows you to store each programme manually. 4. Press the button repeatedly until MANUAL STORE is selected. 5. Press the button to enter MANUAL STORE menu. 6. Press the button to select SEARCH. button to start manual 7. Press the tuning of channel.
Using other menus (PAL_Asia 1) RETURN TO TOP OF THE PAGE Selecting the Colour/Sound System This feature allows you to select your desired COLOUR and SOUND system. If AUTO is selected, the respective colour and sound system will be automatically selected in accordance with the transmission system. Note: Select your desired colour and sound system manually if reception is poor in AUTO mode. Repeat steps 1 to 5 as in 'Manual Tuning of Channels'. button. COLOUR 6. Press the SYSTEM is selected.
Using other menus (PAL_Asia 1) This feature allows you to adjust picture reception in areas of weak reception. 1. Press the MENU key to display the main menu. 2. Press the button repeatedly until INSTALL is selected. 3. Press the button to enter INSTALL menu. 4. Press the button repeatedly until MANUAL STORE is selected. 5. Press the to enter MANUAL STORE menu. 6. Press the button repeatedly until FINE TUNE is selected. or button to start 7. Use the fine-tuning until desired picture and sound is obtained.
Using other menus (PAL_Asia 1) 11. To exit from the menus, press the button. RETURN TO TOP OF THE PAGE Editing of Channels This feature allows you to edit or skip channels which have a poor or weak TV signal or channels that you do not watch often. 4. Press the button repeatedly until CHANNEL EDIT is selected. 5. Press the button to enter channel edit mode. Note: Once a channel has been skipped, you cannot access it via the CHANNEL + or - button.
Using other menus (PAL_Asia 1) RETURN TO TOP OF THE PAGE Naming of Channels This feature allows you to select 10 predefined channels. It also allows you to enter a new name or modify the existing name of a channel for 40 channels, including external channels. 1. Press the MENU key to display the main menu. 2. Press the button repeatedly until INSTALL is selected. 3. Press the button to enter INSTALL menu. 4. Press the button repeatedly until NAME is selected. 5. Press the button to enter NAME mode. 6.
Using other menus (PAL_Asia 1) (You can enter up to a maximum of 5 characters) 9. Press the MENU button to store named channel. 10. To exit from the menus, press the button. RETURN TO TOP OF THE PAGE Using the Picture/Sound Menu The picture and sound menu allows you to make adjustments to the picture and sound. It also allow you to select and activate other features in the menu. 1. Press the MENU key to display the main menu. 2. Press the button repeatedly until INSTALL is selected. 3.
Using other menus (PAL_Asia 1) ● INCREDIBLE PICTURE: Selecting the 'ON' option enhances the detail in the picture. The result is a more dynamic and vivid picture. Note: HUE feature is only applicable to NTSC programmes. The HUE item will not appear on the menu if the programme is in PAL mode. Description of the sound settings: ● TREBLE: Increase or decrease the high frequency level. ● BASS: Increase or decrease the low frequency level. ● BALANCE: Adjusts the balance of the right and left speakers.
Using other menus (NTSC_1) Using Other Menus (NTSC System) Using Your Remote Control • Using Other Menu: PAL System - Europe • PAL System Asia Install: Language • Tuner • Auto Programme • Manual • Channel Edit • Name Picture: Adjusting the Picture Sound: Adjusting the Sound Features: The Timer • The AutoLockTM • The Closed Captioning Control Using Other Menus (with remote control) Language 1. Press the PC/TV button on the remote control to 'TV' mode. 2.
Using other menus (NTSC_1) 3. Press to shift the menu to the left. 4. Press once to highlight the TUNER MODE. 5. Press to highlight the tuner option. 6. With the TUNER MODE set to AUTO, Auto Program (see left) will detect whether or not cable input is present. If, however, you want to set the TUNER MODE to CABLE or ANTENNA, press or until either CABLE or ANTENNA is highlighted. 7. Press the MENU button repeatedly to clear the menu from the screen. 1.
Using other menus (NTSC_1) clear the menu from the screen. Smart Help After you've run Auto Program, check the results. Press the CHANNEL (+) or (-) button and see which channels you can select. Remember an antenna or Cable TV signal must be connected to your Monitor TV first (see the 'Basic Monitor TV connection' section) If you want to delete any unwanted channels from the memory of the Monitor TV, see the 'Channel Edit' section. RETURN TO TOP OF THE PAGE Manual 1.
Using other menus (NTSC_1) Channel Edit 1. Press the MENU button on the remote control to show the on-screen menu. 2. Press repeatedly until INSTALL is highlighted. to shift the menu to the 3. Press left. LANGUAGE will be highlighted. 4. Press repeatedly until CHANNEL EDIT control is highlighted. 5. Press to access the CHANNEL EDIT menu. 6.
Using other menus (NTSC_1) Press and repeat for the second, third, fourth and fifth characters. 8. After you have selected a name for the channel, press the MENU button to save the name in the TV's memory. 9. Press MENU button repeatedly to clear the menu from the screen. Smart Help The five characters that you can enter for the channel NAME features can be letters, a dash character, a space or any number from 0 to 9. RETURN TO TOP OF THE PAGE Adjusting the Picture 1.
Using other menus (NTSC_1) COOL: makes whites, bluish. WARM: makes whites, reddish. 3. Use or keys to adjust the BRIGHTNESS level of the picture. 4. After adjusting the BRIGHTNESS control, press to select another picture adjustment: COLOR, PICTURE, SHARPNESS, TINT, COLOR TEMP or IMAGEMAX. or to adjust the Press selected control. Note: The menu will show only five items at a time, so you will need to continue scrolling with to adjust the COLOR TEMP and IMAGEMAX. 5.
Using other menus (NTSC_1) ● ● and the menu will shift to 3. Press the left. TREBLE will be highlighted and an adjustment bar will be shown to the right. or to adjust the 4. Use TREBLE (high frequency) level of the television sound. 5. After adjusting the TREBLE control, press to select another sound adjustment: BASS, BALANCE AVL, INCR. SURROUND, STEREO, SAP or SPEAKERS. or to adjust the Press selected control. 6. Press the MENU button repeatedly to clear the menu from the screen.
Using other menus (PAL_Asia 2) Using Other Menus (PAL System - Asia) Using Your Remote Control • Using Other Menu: PAL System - Europe • NTSC System Install: Selecting the Menu Language and Automatic Tuning of Channels • Manual Tuning of Channels • Selecting the Colour/Sound System • Fine Tuning of Channels • Sorting of Channels • Editing of Channels • Naming of Channels Picture/Sound: Using the Picture/Sound Menu Features: Activating the Timer • Activating the Child Lock (Access/Change Code) • Activating
Using other menus (PAL_Asia 2) button to activate timer. 16. Press the 1. Press the button to enter You can select to activate timer by TIMER menu. DAILY or ONCE mode. 2. Press the button to enter TIME 17. Press the button to select mode. DISPLAY. 3. Key in the current time. For button to select ON 18. Press the example, if the current time is 12:30, mode if you want to display the key digit 1 and 2 in the hour column, current time on the TV screen. followed by digit 3 and 0 in the 19.
Using other menus (PAL_Asia 2) When the new code is confirmed, the message CORRECT will appear. 12. To exit from the menus, press the button. Note: After you have cleared the menu from screen and you want to enter child lock menu again, you only need to key in the new access code once. If you have forgotten the new access code, key in 0711 twice to enter the child lock menu. Upon entering the child lock menu, you can proceed to change code again.
Using other menus (PAL_Asia 2) Note: You cannot access the locked channels via the front controls of the TV set. You can only access the locked channels via the remote control. When AVI source is locked, the CVI source is automatically locked. Similarly, if the CVI source is locked, the AVI source is also automatically locked because they share the same audio input. If you attempt to enter the INSTALL menu after locking a channel, a message 'Enter ACCESS CODE' will appear on the screen.
Using other menus (PAL_Asia 2) The programme listing feature allows you to navigate through a list of installed programmes to gain a quick overview of the channels and activate the channel you have selected. (PROGRAM LIST) 1. Press the button to display the list of installed programmes. The current channel is highlighted. 2. Press the or button to run through the programme list and highlight the channel number you want to activate. 3. Press the button to activate the channel you have selected. 4.
Using other menus (PAL_Asia 2) Definition of Picture Settings PERSONAL Picture settings are set to your preference. RICH Emphasizes very vibrant colours. (Suitable for AV mode in brightly-lit room) NATURAL Emphasizes original colours. SOFT Emphasizes 'warm' colours. (Suitable for dimly-lit room and gives cinema-like effect when light is switched off). MULTIMEDIA Emphasizes 'soft' colours. (Suitable for playing computer games, surfing, etc.
Using other menus (NTSC_2) Using Other Menus (NTSC System) Using your Remote Control • Using Other Menu: PAL System - Europe • PAL System Asia Install: Language • Tuner • Auto Program • Manual • Channel Edit • Name Picture: Adjusting the Picture Sound: Adjusting the Sound Features: The Timer • The AutoLockTM • The Closed Captioning Control Setting the Clock Your television comes with an on-screen clock. During normal operation, the clock appears on the screen when the TIMER DISPLAY control is turned ON.
Using other menus (NTSC_2) 1. Press the MENU button on the remote control to show the on-screen menu. Just as you would an alarm clock, you can set the TV to turn itself ON once or at the same time every day. 2. Press twice to highlight FEATURES. and the menu 3. Press will shift to the left. TIMER will be highlighted. again to shift 4. Press the display left. Then press once to highlight the START TIME control. again to 5. Press highlight the time indicator area. or to move 6.
Using other menus (NTSC_2) 1. Press the MENU button on the remote control to show the on-screen menu. Use the START TIME control to set the TV to turn itself ON once or at the same time every day. The following steps will guide you in setting the TV to turn itself OFF once or at the same time every day. 2. Press twice to highlight FEATURES. and the menu 3. Press will shift to the left. TIMER will be highlighted. again to shift 4. Press the display left.
Using other menus (NTSC_2) You can select a specific channel to appear on the television when the timer turns the set ON. Follow these steps to select the channel. 1. Press the MENU button on the remote control to show the on-screen menu. 2. Press twice to highlight FEATURES. 3. Press and the menu will shift to the left. TIMER will be highlighted. again to shift the menu to the 4. Press left. Then press repeatedly until the CHANNEL control is highlighted. 5.
Using other menus (NTSC_2) left. Then press repeatedly until the ACTIVATE control is highlighted. again to set ACTIVATE to 5. Press again for DAILY; and ONCE; press again to toggle ACTIVATE to press OFF. 6. Press the MENU button repeatedly to clear the menu from the screen. RETURN TO TOP OF THE PAGE Turning ON the Timer Display After the TV's clock has been set, you can use your TV as a clock. The TIMER DISPLAY control allows you to permanently display the time in the upper right corner of the screen.
Using other menus (NTSC_2) RETURN TO TOP OF THE PAGE Understanding AutoLockTM The AutoLockTM feature receives and processes the data that contains programme content advice sent by the broadcasters or other programme providers. When programmed by the viewer, a TV with AutoLockTM can respond to the content advice and block any programme content that may be considered unsuitable (such as offensive language, violence, sexual situations, etc.).
Using other menus (NTSC_2) that have no rating or are unrated. When the BLOCKING control is OFF, the blocking or censoring of programmes is disabled. When the BLOCKING control is ON, programmes will be blocked in accordance with the settings you have chosen. BLOCK UNRATED: All unrated programmes will be blocked if this feature is set to ON. UNRATED programmes are encoded with information from the MPAA (Motion Picture Association of America) or TV broadcasters, but do not have a specific rating.
Using other menus (NTSC_2) G: General Audience - All ages admitted. Most parents would find these programmes suitable for all ages. This type of programme contains little or no violence, no strong language and little or no sexual dialogue or sexual situations. PG: Parental Guidance Suggested These types of programmes contain material that parents may find unsuitable for children under the age of 13.
Using other menus (NTSC_2) graphic violence (V), explicit sexual situations (S), or crude, indecent language (L). RETURN TO TOP OF THE PAGE Setting up the Access Code AutoLockTM allows parents to block out or 'censor' any channels they think children should not watch. A channel blocked by the AutoLockTM control cannot be viewed until a correct access code is used to unlock the channel for viewing. First, let's set your AutoLock access code. file:///D|/TV/english/150mt/osd/n_f.
Using other menus (NTSC_2) RETURN TO TOP OF THE PAGE Blocking Channels After your personal access code has been set you are ready to select the channels or inputs you want to block out or censor. 1. Press the MENU button on the remote control to show the on-screen menu. 2. Press twice to highlight FEATURES. and the menu will shift to 3. Press the left. Then press once to highlight the AutoLock control. 4. Use again to highlight ACCESS CODE. 5. Enter your four-digit ACCESS CODE.
Using other menus (NTSC_2) and the menu will shift to 3. Press the left. Then press once to highlight the AutoLock control. 4. Use again to highlight ACCESS CODE. 5. Enter your four-digit ACCESS CODE. CORRECT will flash very briefly in red and the menu will move to the left with BLOCK CHANNEL highlighted. 6. Press repeatedly until MOVIE RATING is highlighted. 7. Press and the Rating menu shifts to the left with G highlighted. 8. Press or to highlight each rating you want.
Using other menus (NTSC_2) 8. Press or to select a rating. 9. Press or to turn the block on the rating ON or OFF. NOTE: More specific sub ratings (for violence, sexual content, dialogue, or fantasy violence) are available for TV-Y7, TV-PC, TV-14 and TV-MA. 10. To access these sub ratings, press . Press or to select the sub rating that you want to block or or to turn unblock. Then press the block on the sub rating ON or OFF. 11. Press the MENU button repeatedly to clear the menu from the screen.
Using other menus (NTSC_2) OPTIONS is highlighted. to enter the BLOCK 7. Press OPTIONS menu. BLOCKING will be highlighted. 8. Press or to toggle BLOCKING ON or OFF. 9. Press the MENU button repeatedly to clear the menu from the screen. RETURN TO TOP OF THE PAGE Blocking Unrated Broadcasts In addition to blocking specific ratings or channels, you may choose to block all programmes that are unrated. 1. Press the MENU button on the remote control to show the on-screen menu. 2.
Using other menus (NTSC_2) 10. Press the MENU button repeatedly to clear the menu from the screen. NOTE: If the BLOCK OPTIONS, BLOCK UNRATED control is turned ON, all unrated programmes will display the screen shown to the left. To watch the channel, enter your access code or change the BLOCK UNRATED option back to OFF.
Using other menus (NTSC_2) 10. Press the MENU button repeatedly to clear the menu from the screen. NOTE: If the BLOCK OPTIONS, BLOCK UNRATED control is turned ON, all programmes containing NO content advisory data will display the screen shown to the left. To watch the channel, enter your access code or change the NO RATING option back to OFF. RETURN TO TOP OF THE PAGE Viewing Blocked Programming Various on-screen messages will appear when someone tries to programmes that have been blocked.
Using other menus (NTSC_2) If you tune to a specific channel that has been blocked by BLOCK CHANNEL or any of the AutoLockTM RATING options, simply enter your four-digit access code to view the channel. NOTE: this will unblock ALL channels until the TV is switched OFF. When the power to the TV is switched back ON, all previously blocked channels will be blocked again.
Using other menus (NTSC_2) MUTE, TXT1, TXT2, TXT3 or TXT4. CC DISPLAY turns text OFF or ON if the TV station broadcasting on the channel is making CLOSED CAPTIONING available. With CC DISPLAY highlighted, or to toggle Closed press Captioning ON or OFF. NOTE: You also can press the CC button on the remote control to turn the CC TEXT option ON or OFF. 7. Press the MENU button repeatedly to clear the menu from the screen.
F1rst Choice Warranty Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
United States Guarantee LIMITED WARRANTY (Computer Monitor) Click here to access the Warranty Registration Card. Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two and three. WHO IS COVERED? You must have proof of purchase to receive warranty service.
United States Guarantee Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available). Where CAN I GET MORE INFORMATION? For more information, contact the Philips Customer Care Center by calling (877) 835-1838 (U.S.A. customers only) or (423) 475-0280. Before Requesting Service... Please check your owner's manual before requesting service.
United States Guarantee Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601 Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
F1rst Choice Contact Information F1rst Choice Contact Information Telephone numbers: Austria 01 546 575 603 Luxembourg 408 443 5501 Belgium 02 275 0701 Netherlands 053 482 9800 Cyprus (Greek) 800 92256 Norway 22 70 82 50 Denmark 35 25 87 61 Portugal 0800 831 363 France 03 8717 0033 Sweden 08 632 0016 Germany 0696 698 4712 Switzerland 02 23 10 21 16 Greece 00800 3122 1223 Spain 09 17 45 62 46 Finland 09 2290 1908 United Kingdom 0207 949 0069 Ireland 01 601 1161 U.S.A.
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia• Bangladesh • Brasil • Canada • Chile• China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • India • Indonesia • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Russia • Singapore • South Africa • Taiwan • Thailand • Turkey • Uruguay • Venezuela Eastern Europe CZECH REPUBLIC Philips Service V Mezihorí 2180 00 Prague Phone: (02)-6831581 Fax :
Consumer Information Centers ANTILLES Philips Antillana N.V. Kaminda A.J.E. Kusters 4 Zeelandia, P.O. box 3523-3051 Willemstad, Curacao Phone: (09)-4612799 Fax : (09)-4612772 ARGENTINA Philips Antillana N.V. Vedia 3892 Capital Federal CP: 1430 Buenos Aires Phone: (011)-4544 2047 BRASIL Philips da Amazônia Ind. Elet. Ltda. Av. Luis Carlos Berrini, 1400 - Sao Paulo -SP Phone: 0800-701-0203 CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O.
Consumer Information Centers PARAGUAY Philips del Paraguay S.A. Avenida Artigas 1513 Casilla de Correos 605 Asuncion Phone: (021)-211666 Fax : (021)-213007 PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2136200 Fax : (01)-2136276 URUGUAY Ind.Philips del Uruguay S.A. Luis Alberto de Herrera 1248 Customer Help Desk 11300 Montevideo Phone: (02)-6281111 Fax : (02)-6287777 VENEZUELA Industrias Venezolanas Philips S.A.
Consumer Information Centers NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O. box 1041 Auckland Phone: 0800 477 999 (toll free) Fax : 0800 288 588 (toll free) Asia BANGLADESH Philips Service Centre 100 Kazi Nazrul Islam Avenue Kawran Bazar C/A Dhaka-1215 Phone: (02)-812909 Fax : (02)-813062 CHINA BEIJING Beijing Authorized Service Centre. Consumer Information Centre Building 6, West Street Chong Wen Men, Beijing, Jin Bang Co. Led.
Consumer Information Centers HONG KONG Philips Hong Kong Limited Consumer Information Centre 16/F Hopewell Centre 17 Kennedy Road, WANCHAI Phone: 2619 9663 Fax : 2481 5847 INDIA Phone: 91-20-712 2048 ext: 2765 Fax: 91-20-712 1558 BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr.
Consumer Information Centers KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone:080-600-6600 (Local toll free) Fax : (02)-709-1245 MALAYSIA Philips Malaysia Sdn. Berhad Service Dept. No.51,sect.13 Jalan University. 46200 Petaling Jaya, Selagor. P.O.box 12163 50768 Kuala Lumpur. Phone: (03)-7950 5501/02 Fax : (03)-7954 8504 PAKISTAN KARACHI Philips Electrical Ind. of Pakistan Consumer Information Centre F-54, S.I.T.E, P.O.
Consumer Information Centers SINGAPORE Philips Singapore Private Ltd. Consumer Service Dept. Lorong 1,Toa Payoh., P.O. box 340 Singapore 1231 Phone: 6882 3999 Fax : 6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 26F, 66, Chung-Hsiao W. Road Sec. 1 TAIPEI Phone: 0800-231-099 or (02)-2382-4567 Fax : (02)-2382-3027 THAILAND Philips Electronics (Thailand) Ltd.
Consumer Information Centers DUBAI Philips Middle East B.V. Consumer Information Centre P.O.Box 7785 DUBAI Phone: (04)-335 3666 Fax : (04)-335 3999 EGYPT Philips Egypt Consumer Information Centre 10, Abdel Rahman El Rafei Mohandessin - Cairo, P.O.Box 242 DOKKI Phone: (02)-3313993 Fax : (02)-3492142 file:///D|/TV/english/warranty/warcic.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 1 It Takes Only A Moment To PROTECT YOUR INVESTMENT. Congratulations on investing in a Philips product. It’s an important and intelligent decision that’s sure to reward you for many years to come. To ensure you’ll get all of the privileges and protection that come with your purchase, please complete your Warranty Registration Card within the next ten days. SIMPLY MAIL THE CARD BELOW TO RECEIVE ALL OF THESE BENEFITS TO WHICH YOU’RE ENTITLED.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 2 !1375415338! PO BOX 1533 DEPOSIT NY 13754-1533 Please Open Promptly! TIME-DATED MATERIAL a PLEASE APPLY FIRST CLASS STAMP IMPORTANT Warranty Registration Card RETURN THE ATTACHED CARD WITHIN TEN DAYS TO ENSURE YOUR: ✓ Warranty Verification ✓ Owner Confirmation ✓ Model Registration See Inside For Valuable Benefits!
