electronic user's manual file:///D|/EDFU/crt_19/edoc/english/109P/manual.
Royal Philips Electronics - Global home http://www.philips.com/Default.
Safety & Troubleshooting Safety and Troubleshooting Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.
About This Electronic User's Manual About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips Color Monitor. It describes the monitor's features, setup, operation and all other information, which is the same exact information described in our printed version.
About This Electronic User's Manual ● Philips Color Monitor Quick Start Guide which summarizes the steps for setting up the monitor. This is included with this product. RETURN TO TOP OF THE PAGE Notational Descriptions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
About This Electronic User's Manual ©2001 Koninklijke Philips Electronics N.V. All rights reserved. Reproduction, copying, usage, modifying, hiring, renting, public performance, transmission and/or broadcasting in whole or in part is prohibited without written consent of Philips Electronics N.V. file:///D|/EDFU/crt_19/edoc/english/109P/ABOUT/ABOUT.
109P Product Information Product Information Product Features • Technical Specifications • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Product Features Model Regulation Color 109P40 TCO'03 Gray 109P4: ● ● ● ● ● ● ● 19-inch (18.
109P Product Information • Phosphor B22 • Recommended display area 14.0" x 10.4" / 355 x 265 mm • Maximum display area 14.4" x 10.8" / 365 x 274 mm SCANNING • Horizontal scanning 30 - 111 KHz • Vertical scanning 50 - 160 Hz VIDEO • Video dot rate 290 MHz • Input impedance - Video 75 ohm - Sync 4.7 kOhm • Input signal levels 0.
109P Product Information sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.) Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen.
9P Product Information Power Management Definition VESA's Mode Video H-sync V-sync Power Used Power Saving (%) LED color ON Active Yes Yes Typical 120 W 0% Verde OFF Blanked No No < 1W 99% Chihlimbar This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimensions 17.9"x 18.5" x 17.
109P Product Information RETURN TO TOP OF THE PAGE Pin Assignment The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin Assignment No. Pin Assignment No. 1 Red video input 9 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 Identical output connected to pin 10 4 Identical output connected to pin 10 12 Serial data line (SDA) 5 Ground 13 H. Sync / H+V 6 Red video ground 14 V.
109P Product Information Follow the links to see various views of the monitor and its components. Front View Rear View RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19/edoc/english/109P/PRODUCT/PRODUCT.
Installing your Monitor Installing your Monitor Front View • Rear View Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls file:///D|/EDFU/crt_19/edoc/english/INSTALL_4/INSTALL.
Installing your Monitor Contrast hotkey. When the UP arrow is pressed, the adjustment controls for the CONTRAST will show up. UP and DOWN buttons are used when adjusting the OSD of your monitor Brightness hotkey. When the RIGHT arrow is pressed ,the adjustment controls for BRIGHTNESS will show up. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. By pressing both the UP and OK buttons, you can easily access the Input Signals A and/or B.
Installing your Monitor 1. D-Sub Port - Attach the D-Sub connector that comes with your monitor here. Other end connects to your PC. 2. Power in - Attach power cable here. file:///D|/EDFU/crt_19/edoc/english/INSTALL_4/INSTALL.
Installing your Monitor 3. BNC Connectors - Attach the connectors here to get the best video performance from your monitor. RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19/edoc/english/INSTALL_4/INSTALL.
On-Screen Display On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides userfriendliness and ease-of-use when operating the monitor. Basic and simple instruction on the control keys.
On-Screen Display RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. Your monitor may not include all the items in the OSD tree shown below. file:///D|/EDFU/crt_19/edoc/english/OSD/OSDDESC.
On-Screen Display file:///D|/EDFU/crt_19/edoc/english/OSD/OSDDESC.
On-Screen Display RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19/edoc/english/OSD/OSDDESC.
Customer Care and Warranty Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO READ THE WARRANTY COVERED: WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EASTERN EUROPE: Czech Republic • Hungary • Poland • Russia • Turkey • Bulgaria LATIN AMERICA: Antilles • Argentina • Brazil • Chile • Colombia • Mexico • Paraguay • Peru • Uruguay • Venezue
Frequently Asked Questions Frequently Asked Questions 1. What does the "Designed for Windows" logo signify? The "Designed for Windows" logo means your Philips monitor fulfills the requirements and recommendations of the PC9x (97, 98, or 99) System Design Guide and passes stringent WHQL tests. 2. What is USB? Think of USB as a smart plug for PC peripherals. USB automatically determines resources (like driver software and bus bandwidth) required by peripherals.
Frequently Asked Questions 6. What models are Mac compatible? All listed Philips monitors are Mac compatible. BUT, you may need an adapter to connect the monitor to your Mac system. Please contact your dealer/reseller for details. 7. What is TCO? TCO is a Swedish abbreviation for the Swedish Confederation of Professional Employees. 8. What is MPR? MPR is a Swedish abbreviation for the Swedish National Board of Measurement and Testing. 9.
Frequently Asked Questions Energy Saving: MPRII: No requirement. TCO92: Standby mode < 30W, Off mode < 8W TCO95: Standby mode < 30W, Off mode < 8W TCO99: Standby mode < 15W, Off mode < 5W TCO'03:Standby mode < 15W, Off mode < 5W Visual Ergonomics: MPRII: No requirement. TCO92: No requirement. TCO95: Set ergonomic rules including minimum contrast level, flicker and jitter. TCO99: Tightened TCO95 rules. TCO'03: Tighten TCO99 rule for CRT and new requirement of screen color for TFT LCD Monitors.
Frequently Asked Questions "Refresh rate" describes the number of times an entire screen is vertically scanned each second. In other words: If a monitor's refresh rate is 85 Hz, its screen is refreshed - or vertically scanned - 85 times per second. A higher the refresh rate means better image stability and less flicker. A high refresh rate helps users who work long hours in front of a monitor avoid eye fatigue and stress.
Frequently Asked Questions Simply press OK button then select "Reset to factory settings" to restore all settings. 16. What is LightFrame ? LightFrame is a Philips technology breakthrough which offers a unique and revolutionary solution for boosting a monitor 's brightness and sharpness. With LightFrameTM, the user experiences TV quality performance for video or photos without deterioration to the monitor 's performance in windows used for other applications. 17.
Frequently Asked Questions 19. Will anyone else have this? LightFrame was invented, developed and patented by Philips. It is a unique feature that you will find exclusively in Philips monitors. 20. Will LightFrame shorten the life of a monitor? No. Extensive testing has confirmed LightFrame does not adversely affect monitor life. Today's state-of- the-art Philips monitors employ improved phosphors and are designed for high light output. LightFrame normally highlights photos and videos.
Frequently Asked Questions Philips exclusive LightFrame feature requires the combined operation of hardware that resides in your monitor and software installed on your system. It only works when a monitor with built-in hardware receives commands from system software. Without both the LightFrameTM hardware equipped monitor and system software, the LightFrame does not function. 23.
Frequently Asked Questions 26. Which models can be incorporated with the Multimedia Base? The following models can be incorporated with the Multimedia Base: 109B5, 109E5,109F5, 107B5, 107E5,107F5, 107S5, 107T5. 27. What are Philips Multimedia Base's specifications? See detailed Multimedia Base specifications on the product information page. 28. Why is a Multimedia Base better than separate speakers? The major advantage of the Multimedia Base is its minimal space requirements.
Frequently Asked Questions of years, the monitor's brightness deteriorates to below 50% of its original value. At this stage, the usable life of a monitor is considered ended. Auto Calibrate regularly readjusts color temperature and luminance to their original values. 31. How does Philips Auto Calibrate feature benefit me? With Auto Calibrate, it takes a monitor's luminance 33 percent longer to deteriorate to the 50 percent level that marks the end of a display device's useful life.
Frequently Asked Questions Auto Calibrate is currently available in the new 201P, 201B and 109P. 35. The Main Menu displays OSD MAIN MENU LOCKED . Pressing the front control panels hasno effect. How can I unlock this function? Press and hold the OSD menu key for about 10 seconds until picture displays "OSD MAIN MENU UNLOCKED" 36.
Frequently Asked Questions ● ● ● ● Some monitors have a Moire cancellation feature, activate it to the on position or adjust the Moire cancellation function via the OSD on the monitor. Change resolution to the recommended standard for the specific monitor size. Change Window viewing pattern/scheme to a pattern where the Moire is less visible. Change horizontal and vertical size to optimize the reduction of the Moire effect. 39.
Frequently Asked Questions 42. How do I adjust the picture on the screen? Please perform the following to correct the picture image: ● ● ● Reset your monitor via the OSD menu Adjust the Horz (width) and/or Vert size (height) in the OSD Change monitor timing to work at the recommended resolution 43. The edge of the picture on the screen appears to be distorted.
Frequently Asked Questions 45. I have noticed two thin horizontal lines on the screen of my Philips monitor. Is this normal? This phenomenon can occur with Philips 107P, 109P and 201P monitors and is normal. Your monitor is using an Aperture Grille, which consists of fine vertical wires to align the electron beams with the phosphors on the screen. To prevent these vertical wires from vibrating and to keep them properly aligned with the picture tube, two horizontal damper wires are required.
Frequently Asked Questions 49. Why is there no picture on my monitor even though the power LED is green? ● Verify the Contrast and Brightness setting of the monitor. First press and hold the 5 (-) button to increase Contrast and then press and hold the 4 (+) button to increase Brightness. These buttons are located on the front of your monitor. ● ● Press both the 5(-) button and the OK button at the same time to switch input A|B. Try and repeat step 48 above. 50.
Glossary Glossary ABCDEFGHIJKLMNOPQRSTUVWXYZ A Autoscan A microprocessor-based feature of Philips Brilliance monitors is able to detect automatically horizontal and vertical frequencies of input signals with those of the installed video card. An autoscan monitor can thus operate with a wide range of video cards. MultiSync, a registered trademark of NEC, provides a similar function.
Glossary RETURN TO TOP OF THE PAGE C CE Mark CE mark is displayed on products per EMC and LV ( low Voltage Device ) directives in compliance with European Community safety, EMI and EMS requirements and is compulsory on products for sale in the European Community. Color temperature A way of describing the color of a radiating source in terms of the temperature (in degrees Kelvin) of a black body radiating with the same dominant frequency as the source.
Glossary a picture is set by the brightness of the unexcited phosphor, which is governed by the degree with which ambient light is reflected. Contrast is therefore reduced in conditions of high ambient light levels. Black Matrix tubes reflect less ambient light so exhibit higher contrast than other tubes. Convergence error Bean misalignment causing one or more of the three beams passing through the wrong aperture in the shadow mask and striking a phosphor dot in the wrong triad.
Glossary Cathode-ray tube - the general term for all tubes in which one or more electron beams emitted by a cathode are periodically scanned across a phosphor screen by means of deflection circuitry. A special form of the cathode-ray tube is the TV and monitor picture tube. RETURN TO TOP OF THE PAGE D DDC (Display Data Channel) DDC is a communication channel for displays and computers.
Glossary DDC 1/2B See DDC. DDC 2Bi See DDC. Degaussing The procedure of demagnetizing the shadow mask and associated metal parts of a picture tube at switch-on to minimize picture distortion. This is usually accomplished by means of a special degaussing coil through which a decaying alternating current is passed to generate an alternating magnetic field that gradually decays to demagnetize the tube. Some monitors offer a manual degaussing facility that can be activated at any time.
Glossary Dot rate Frequency in MHz of the dot clock. It is a measure of the speed with which data is transferred between the video card and subsequent processing circuitry. Also known as video dot rate. RETURN TO TOP OF THE PAGE E Electromagnetic radiation standards International standards set to limit electromagnetic emissions from monitors. There are currently file:///D|/EDFU/crt_19/edoc/english/GLOSSARY/GLOSSARY.
Glossary two important standards both derived from regulations originally laid down by Swedish authorities. MPR-II The standard originally proposed by the Swedish National Board of Measurement and Testing. It set maximum levels of electromagnetic radiation emitted by monitors, and has now been adopted as a world standard. MPR-II defines maximum permitted electrostatic, magnetic and electric field levels measured at a distance of 50 cm from the center of the monitor (see table).
Glossary problem can, however, be eliminated by increasing the refresh rate (number of frames/second) of the monitor to a value above around 70 Hz. Sensitivity to flicker appears to diminish with increasing age. RETURN TO TOP OF THE PAGE H Hertz The unit of frequency named after the physicist Heinrich Hertz (1857-1894). 1 hertz (Hz) is equal to 1 cycle/second. Horizontal dot pitch See Dot pitch.
Glossary INF file (Information File) Information (INF) files store information in a specific format. The set-up functions retrieve information from the INF file to use when performing installation operations. Examples of the type of information stored in an INF file include INI and registry changes, file names, and locations of the source files on source media. Interlaced/non-interlaced Interlaced.
Glossary L Linearity The degree to measure the actual location of a pixel on the screen corresponds with its intended location. ( see figure ) Line frequency See Horizontal scanning frequency. Low-emission monitor A monitor that complies with international standards on radiation. See Electromagnetic radiation standards. Low-frequency electric and magnetic fields file:///D|/EDFU/crt_19/edoc/english/GLOSSARY/GLOSSARY.
Glossary Alternating fields generated by the deflection yoke. These are subject to increasing attention, notably by governing authorities, the trade and the press. Although there is no scientific evidence that monitor emissions are harmful, much effort has gone into reducing emissions on the principle of better safe than sorry.
Glossary N Non-interlaced See Interlaced/non-interlaced. RETURN TO TOP OF THE PAGE O OSD (On Screen Display) The feature that allows an end user to adjust screen performance and parameters of monitors directly through an on-screen instruction window. See CustoMax in CrystalClear section. Overscan The practice in which areas without useful video information are scanned outside the visible screen area in order to make maximum use of the screen for display of active video information.
Glossary Parallelogram Distortion See Geometric distortion. Phosphor Generic name for the class of substances that exhibit luminescence. To produce a picture on screen, phosphors are deposited on the inner surface of the picture-tube screen and excited into luminescence by the electron beam. Typical examples of phosphors are P22 medium shortpersistence phosphor and EBU high-color-saturation phosphor. Pin-cushion Distortion See Geometric distortion.
Glossary Plug-and-Play See DDC. See USB section. RETURN TO TOP OF THE PAGE R Raster The area on screen that electron beam can reach. Refresh rate See Vertical scanning frequency. Resolution The number of pixels that can be displayed on the screen. The resolution is specified as the number of pixels in a line multiplied by the number of horizontal lines. See also video graphic adapter. Rotation function The feature that allows users to adjust the whole screen rotating to be horizontal.
Glossary S Screen coatings Anti-Static coatings Due to bombardment by beam electrons, monitor screens become electrically charged when in use. Electrically charged screens surfaces can attract dust particles. An Anti-Static coating is a conductive coating deposited on the screen (or on a glass panel immediately in front of the screen) that conducts away the charge and prevents screen dust build-up.
Glossary ARAS is one of the most effective anti-reflection/anti-static screen treatments currently available. It is composed of a multi-layer structure of transparent dielectric material that suppresses specular reflections by broadband interference effects at the screen surface. Anti-static properties are provided by a single conductive layer within the multi-layer structure. With ARAS, the intensity of reflected light is reduced from around 4.
Glossary common: SOG (Synchronization On Green) A properly functioning color monitor requires five kinds of signals: horizontal sync pulse, vertical sync pulse, red color signal, green color signal and blue color signal. Signals from a PC are transmitted to a monitor using one of three methods: 1. Separate sync: Horizontal and Vertical sync signals transmitted separately 2. Composite sync: Horizontal and vertical sync pulses mixed into a single signal train. 3.
Glossary T TCO See Electromagnetic radiation standards. Tilt function See rotation function. Trapezoid distortion See Geometrical distortion. TTL signal A TTL (Transistor-transistor-logic) signal is a digital signal level for controlling the screen colors. With TTL driving, the red, green and blue signals can only be switched on or off or provided with an intensity signal. A TTL-driven monitor can thus display a maximum of 64 colors. Video standards such as MDA, CGA and EGA are based on TTL level.
Glossary ● ● ● USB eliminates "case angst" -- the fear of removing the computer case to install add-on peripherals. And USB also eliminates adjustment of complicated IRQ settings when installing new peripherals. USB does away with "port gridlock." Without USB, PCs are normally limited to one printer, two Com port devices (usually a mouse and modem), one Enhanced Parallel Port add-on (scanner or video camera, for example) and a joystick.
Glossary for example, a data/FAX modem device. Devices may be physical, electrical, addressable, and logical. Downstream The direction of data flow from the host or away from the host. A downstream port is the port on a hub electrically farthest from the host that generates downstream data traffic from the hub. Downstream ports receive upstream data traffic. Upstream The direction of data flow towards the host.
Glossary V Vertical dot pitch See Dot pitch. Vertical scanning frequency Expressed in Hz, this is the number of fields written to the screen every second in interlaced mode. In non-interlaced mode vertical scanning frequency is the number of frames (complete pictures) written to the screen every second (also known as refresh rate). Vertical sync pulses A train of square shaped waveforms that define the start of a new frame.
Glossary A card equipped with a character or graphic generator and video memory, which maps to the screen. A microprocessor scans video memory and translates bit information from the computer into displayable video signals for the monitor. These cards comply with various standards that determine the nature and quality of the display. VGA (Video Graphics Array), introduced in 1987, was the first analog card.
Download and Print Download and Print This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install the application. Adobe® Acrobat Reader for PC / Adobe® Acrobat Reader for Mac. Download instructions: To download the file: 1. Click-and-hold your mouse over the icon below. (Win95/98 users right-click) 2.
Download and Print 202F.pdf 202P.pdf file:///D|/EDFU/crt_19/edoc/english/DOWNLOAD/DOWNLOAD.
Troubleshooting Troubleshooting Safety Precautions and Maintenance • Troubleshooting • Regulatory Information• Other Related Information Common Problems Having trouble? Something not working? Before calling for help, try these suggestions.
Troubleshooting No color or intermittent color ● ● ● Color appears blotchy ● ● Missing one or more colors ● ● ● Dim Picture Picture is too large or too small. Edges of the picture are not square. ● Unstable Picture Problem with On Screen Display Check the Color Temperature. Make sure the monitor cable is properly connected to your computer. Check to see if the monitor cable has bent pins. Adjust the Brightness and Contrast controls.
Troubleshooting For further assistance, refer to the Consumer Information Centers list to contact your local Philips distributor. RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19/edoc/english/109P/SAFETY/saf_troub.
Regulatory Information Regulatory Information TCO'99 Information • TCO'99 Environmental Requirements • TCO'03 Information • Recycling Information for Customers • CE Declaration of Conformity • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S.
Regulatory Information recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g.
Regulatory Information Current information regarding TCO' 99 approved and labeled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ RETURN TO TOP OF THE PAGE Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances.
Regulatory Information CFCs (freons) The relevant TCO' 99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with increased risks e.g. skin cancer (malignant melanoma) as a consequence.
Regulatory Information Some of the features of the TCO'03 Display requirements. Ergonomics ● Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability.
Regulatory Information For more information, please visit www.tcodevelopment.com RETURN TO TOP OF THE PAGE Recycling Information for Customers Philips establishes technically and economically viable objectives to optimize the environmental performance of the organization's product, service and activities. From the planning, design and production stages, Philips emphasizes the important of making products that can easily be recycled.
Regulatory Information Ms. Delmer F. Teglas Philips Electronics North America E-mail: butch.teglas@philips.
Regulatory Information Energy Star Declaration PHILIPS 109P4* This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirements in the NUTEK specification 803299/94. Time settings are adjusted from the system unit by software.
Regulatory Information harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● ● ● ● Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Regulatory Information corriger la situation en prenant les mesures suivantes: ● ● ● ● Réorienter ou déplacer l'antenne de réception. Augmenter la distance entre l'équipement et le récepteur. Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur. Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.
Regulatory Information VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio Interference. Install and use the equipment according to the instruction manual.
Regulatory Information environment, including residential areas. RETURN TO TOP OF THE PAGE Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.
Regulatory Information RETURN TO TOP OF THE PAGE North Europe Information (Nordic Countries) Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. file:///D|/EDFU/crt_19/edoc/english/109P/SAFETY/regs/regulat.
Regulatory Information Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ. RETURN TO TOP OF THE PAGE BSMI Notice (Taiwan Only) file:///D|/EDFU/crt_19/edoc/english/109P/SAFETY/regs/regulat.
Regulatory Information RETURN TO TOP OF THE PAGE Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbedenklichkeit der Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Störstrahlern nach Anlage III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind.
Regulatory Information Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer. RETURN TO TOP OF THE PAGE Information for UK only WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A. S.T.A. or BSI approved type. 3. Refit the fuse cover.
Regulatory Information How to connect a plug The wires in the mains lead are coloured in accordance with the following code: BLUE - "NEUTRAL" ("N") BROWN - "LIVE" ("L") GREEN & YELLOW - "EARTH" ("E") 1. The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter "E" or by the Earth symbol or coloured GREEN or GREEN AND YELLOW. 2. The BLUE wire must be connected to the terminal which is marked with the letter "N" or coloured BLACK. 3.
Other Related Information Other Related Information Safety Precautions and Maintenance • Troubleshooting • Regulatory Information • Information for Users in the U. S. • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet long and a parallel blade, grounding type attachment plug rated 15 A, 125 V.
The OSD Controls The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Contrast (HotKey) • Language • Input Signal Selection • Zoom • Adjust Horizontal • Adjust Vertical • Adjust Shape • Adjust Color • Reset to Factory Settings • Extra Controls • Close Main Controls BRIGHTNESS To adjust your screen's brightness, follow the steps below. Brightness is the overall intensity of the light coming from the screen. A 50% brightness is recommended.
The OSD Controls RETURN TO TOP OF THE PAGE CONTRAST To adjust your screen's contrast, follow the steps bellow. Contrast is the difference between the light and dark areas on the screen. A 100% contrast is recommended. 1) Press the or button on the monitor. The CONTRAST window appears. 2) Press the or button to adjust the contrast.
The OSD Controls LANGUAGE The ON SCREEN DISPLAY shows its settings in one of five languages. The default is English, but you can select French, Spanish, German, or Italian. 1) Press the button on the monitor. The MAIN CONTROLS window appears. LANGUAGE should be highlighted. 2) Press the button again. The LANGUAGE window appears. 3) Press the or button until the desired language is highlighted. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 4) Press the button to confirm your selection and return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted... After returning to MAIN CONTROLS . . . Smart Help . . . to continue to INPUT SIGNAL SELECTION, press the button until INPUT SIGNAL SELECTION is highlighted. Next, follow steps 3 - 5 under INPUT SIGNAL SELECTION. . . .
The OSD Controls 3) Press the button. The INPUT SIGNAL SELECTION window appears. 4) Press the or 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. button to highlight INPUT B or INPUT A. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . Smart . . . to continue to ZOOM, press the Help button until ZOOM is highlighted. Next, follow steps 3 - 5 under ZOOM. . . .
The OSD Controls RETURN TO TOP OF THE PAGE ZOOM ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ZOOM is highlighted. 3) Press the button. The ZOOM window appears. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 4) Press the or button to adjust ZOOM. 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . Smart Help . . . to continue to ADJUST HORIZONTAL, press the button until ADJUST HORIZONTAL is highlighted. Next, follow steps 3 - 7 under ADJUST HORIZONTAL. . . .
The OSD Controls 3) Press the button. The ADJUST HORIZONTAL window appears. POSITION should be highlighted. 4) Press the or button to move the image to the left or right. 5) When the position is adjusted, press the press the button to return to MAIN CONTROLS window, or to highlight SIZE. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 6) To adjust the horizontal size, press the 7) When the size is adjusted, press the or button. button to return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . Smart Help . . . to continue to ADJUST VERTICAL, press the button until ADJUST VERTICAL is highlighted. Next, start with step 3 under ADJUST VERTICAL and follow the directions. . . .
The OSD Controls 2) Press the button until ADJUST VERTICAL is highlighted. 3) Press the button. The ADJUST VERTICAL window appears. POSITION should be highlighted. 4) Press the or button to move the image up or down. 5) When the position is adjusted, press the button to return to MAIN CONTROLS window, or file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls press the to highlight SIZE. 6) To adjust the vertical size, press the or button. 7) When the size is adjusted, press the button to return to MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . Smart Help . . . to continue to ADJUST SHAPE, press the button until ADJUST SHAPE is highlighted. Next, start with step 3 under ADJUST SHAPE and follow the directions. . . .
The OSD Controls ADJUST SIDE CURVE under ADJUST SHAPE allows you to adjust two of the five preset options. These two options are PINCUSHION and BALANCED pincushion. Note: use these features only when the picture is not square. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button. The SIDE CURVE window appears.
The OSD Controls 5) To adjust the pincushion, press the or 6) When the pincushion is adjusted, press the button. button to highlight BALANCED or press the button to return to the ADJUST SHAPE window. 7) To adjust the balanced pincushion, press the or 8) When the balanced pincushion is adjusted, press the button. button to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted.
The OSD Controls After returning to MAIN CONTROLS . . . ...to continue to ADJUST SIDE ANGLES, start with step 5 under ADJUST Smart SIDE ANGLES and follow the directions. Help ...to exit completely, press the button twice. ...to adjust only the BALANCED pincushion, follow steps 1 - 4 above, then press the button, and follow steps 7 - 9. ADJUST SIDE ANGLES ADJUST SIDE ANGLES under ADJUST SHAPE allows you to adjust two of the five preset options. These two options are TRAPEZOID and PARALLELOGRAM.
The OSD Controls 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the button to highlight ADJUST SIDE ANGLES. 5) Press the button. The SIDE ANGLES window appears. TRAPEZOID should be highlighted. 6) To adjust the trapezoid, press the or 7) When the trapezoid is adjusted, press the the button. button to highlight PARALLELOGRAM or press button to return to the ADJUST SHAPE window. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 8) To adjust the parallelogram, press the or 9) When the parallelogram is adjusted, press the button. button to return to the ADJUST SHAPE window. BACK TO MAIN WINDOWS will be highlighted. 10) Press the button to return to the MAIN CONTROLS window, or press the button until ROTATE IMAGE is highlighted. After returning to MAIN CONTROLS . . . ...to continue to ROTATE IMAGE, start with step 5 under ROTATE IMAGE and Smart follow the directions. Help ...
The OSD Controls 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST SHAPE is highlighted. 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the arrow until ROTATE IMAGE is highlighted. 5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 6) To adjust the rotation, press the or 7) When the rotation is adjusted, press the button. button to return to the ADJUST SHAPE window. BACK TO MAIN CONTROLS should be highlighted. 8) Press the button to return to MAIN CONTROLS. After returning to MAIN CONTROLS . . . Smart Help . . . to continue to ADJUST COLOR, press the button until ADJUST COLOR is highlighted. Next, start with step 3 under ADJUST COLOR and follow the directions. ...to exit completely, press the button twice.
The OSD Controls 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until ADJUST COLOR is highlighted. 3) Press the button. The ADJUST COLOR window appears. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 4) Press the or button to highlight 9300K for GENERAL USE, 6500K for IMAGE MANAGEMENT, 5500K for PHOTO RETOUCH, or USER PRESET. 5) Once you have highlighted GENERAL USE, IMAGE MANAGEMENT, or PHOTO RETOUCH, press the button to confirm you selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. 6a) If USER PRESET is highlighted, press the the or button to highlight RED. Next, press button to adjust the color red.
The OSD Controls After returning to MAIN CONTROLS. . . Smart Help . . . to continue to RESET TO FACTORY SETTINGS, press the button until RESET TO FACTORY SETTINGS is highlighted. Next, start with step 3 under RESET TO FACTORY SETTINGS. . . . to exit completely, press the button. RETURN TO TOP OF THE PAGE RESET TO FACTORY SETTINGS RESET TO FACTORY SETTINGS returns everything in all the windows to factory presets. 1) Press the button on the monitor. The MAIN CONTROLS window appears.
The OSD Controls 3) Press the button. The RESET TO FACTORY SETTINGS window appears. 4) Press the or button to select YES or NO. NO is the default. YES returns all settings to their original factory adjustments. 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . Smart . . . to continue to EXTRA CONTROLS, press the Help button until EXTRA CONTROLS is highlighted.
The OSD Controls . . . to exit completely, press the button. RETURN TO TOP OF THE PAGE EXTRA CONTROLS DEGAUSS EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussing removes electromagnetic build up that may distort the color on your screen. 1) Press the button on the monitor. The MAIN CONTROLS window appears. 2) Press the button until EXTRA CONTROLS is highlighted. 3) Press the button. The EXTRA CONTROLS window appears. MOIRE will be highlighted.
The OSD Controls 4) Press the button to highlight DEGAUSS. 5) To degauss your screen, press the button. Your screen will be degaussed, then the MAIN CONTROLS window will reappear. CLOSE MAIN CONTROLS will be highlighted. After returning to MAIN CONTROLS . . . Smart Help . . . to continue to ADJUST MOIRE, press the button until EXTRA CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS, ADJUST MOIRE. . . . to exit completely, press the button.
The OSD Controls 2) Press the DOWN CURSOR button until EXTRA CONTROLS is highlighted. 3) Press the button. The EXTRA CONTROLS window appears. ADJUST MOIRE will be highlighted. 4) Press the button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls 5) To adjust the horizontal moire, press the or 6) When the horizontal moire is adjusted, press the 7) To adjust the vertical moire, press the or 8) When the vertical moire is adjusted, press the button. button to highlight VERTICAL. button. button to return to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS will be highlighted. Smart After returning to MAIN CONTROLS . . . Help . . . to exit completely, press the button. file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
The OSD Controls CLOSE MAIN CONTROLS RETURN TO TOP OF THE PAGE file:///D|/EDFU/crt_19/edoc/english/OSD/osd_cont.
F1rst Choice Warranty Your Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact the Philips helpdesk directly to benefit from your Philips F1rst Choice Warranty.
F1rst Choice Warranty ● Repairs or product modifications and alterations have been executed by unauthorized service organizations or persons; ● Damage is caused by accidents including but not limited to lightning, water or fire, misuse or neglect; ● Reception problems caused by signal conditions or cable or antenna systems outside the unit; ● Defects caused by abuse or misuse of the monitor; ● Product requires modification or adaptation to enable it to comply with local or national technical standards,
F1rst Choice Warranty Having the following information available will also help speed up the process: ● ● Your proof of purchase indicating: date of purchase, dealer name, model and product serial number. The full address to which the faulty monitor has to be collected and the swap model should be delivered. Philips' customer help desks are located worldwide. Click here to access the F1rst Choice Contact Information. Or you can reach us via: Website: http://www.philips.
International Guarantee Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a period of 12 months from date of purchase.
International Guarantee Website: http://www.philips.com file:///D|/EDFU/crt_19/edoc/english/WARRANTY/war_intl.
United States Guarantee Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly to benefit from your Philips F1rst Choice Warranty.
United States Guarantee When the warranty on the original product expires, the warranty on all replaced and repaired products and parts also expires. WHAT IS EXCLUDED? Your warranty does not cover: ● ● ● ● ● ● labor charges for installation or setup of the product, adjustment of customer controls on the product, and installation or repair of antenna systems outside of the product.
United States Guarantee TO GET WARRANTY SERVICE IN U.S.A., PUERTO RICO OR U.S. VIRGIN ISLANDS... Contact the Philips Customer Care Center phone number listed below for product assistance and procedures for servicing: Philips Customer Care Center (877) 835-1838 or (919) 573-7855 (In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties, including implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the duration of this express warranty.
United States Guarantee This warranty gives you specific legal rights. You may have other rights which vary from state/ province to state/province. Before contacting Philips, please prepare the following details so we can solve your problem quickly.
F1rst Choice Contact Information F1rst Choice Contact Information Telephone numbers: Austria 01 546 575 603 Belgium 02 275 0701 Cyprus 800 92256 Denmark 35 25 87 61 France 03 8717 0033 Germany 0696 698 4712 Greece 00800 3122 1223 Finland 09 2290 1908 Ireland 01 601 1161 Italy 02 48 27 11 53 Luxembourg 026 84 3000 The Netherlands 053 482 9800 Norway 22 70 82 50 Portugal 0800 831 363 Sweden 08 632 0016 Switzerland 02 23 10 21 16 Spain 09 17 45 62 46 United Kingdom 0207 949
Consumer Information Centers Consumer Information Centers Antilles • Argentina • Australia • Bangladesh • Brasil • Canada • Chile • China • Colombia • Czech Republic • Dubai • Egypt • Hong Kong • Hungary • Slovakia• Slovenia • India• Indonesia • Japan • Korea • Malaysia • Mexico • Morocco • New Zealand • Pakistan • Paraguay • Peru • Philippines • Poland • Russia • Singapore • South Africa • Taiwan • Thailand • Turkey • Uruguay • Venezuela Eastern Europe CZECH REPUBLIC Xpectrum Lužná 591/4 CZ - 160 00 Praha
Consumer Information Centers SLOVENIA PC HAND Brezovce 10 SI - 1236 Trzin Tel: +386 1 530 08 24 Email: servis@pchand.si POLAND Zolter ul.Zytnia 1 PL - 05-500 Piaseczno Tel:+48 22 7501766 Email: servmonitor@zolter.com.pl www.zolter.com.pl RUSSIA Tel: +7 095 961-1111 Tel: 8-800-200-0880 Web-site: www.philips.ru TURKEY Türk Philips Ticaret A.S. Yukari Dudullu Org.San.Bolgesi 2.Cadde No:22 34776-Umraniye/Istanbul Tel: (0800)-261 33 02 Latin America ANTILLES Philips Antillana N.V.Kaminda A.J.E.
Consumer Information Centers ARGENTINA Vedia 3892 Capital Federal CP:1430 Buenos Aires Phone: (011)-4544 2047 Fax: (011)-4544 2928 BRASIL Philips da Amazonia Ind. Elet.Ltda. Av.Luis Carlos Berrini, 1400-Sao Paulo-SP Phone: 0800-7010-203 CHILE Philips Chilena S.A. Avenida Santa Maria 0760 P.O. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S.A.-Division de Servicio CARRERA 15 Nr.
Consumer Information Centers PARAGUAY Philips del Paraguay S.A. Avenida Artigas 1513 Casilla de Correos 605 Asuncion Phone: (021)-211666 Fax : (021)-213007 PERU Philips Peruana S.A. Customer Desk Comandante Espinar 719 Casilla 1841 Limab18 Phone: (01)-2136200 Fax : (01)-2136276 URUGUAY Ind.Philips del Uruguay S.A. Lius Alberto de Herrera 1248-P:10 Customer Help Desk 11300 Montevideo Phone: (02)-6281111 Fax : (02)-6287777 VENEZUELA Industrias Venezolanas Philips S.A.
Consumer Information Centers CANADA Philips Electronics Ltd. 281 Hillmount Road Markham Ontario, L6C 2S3 Phone: 800- 479-6696 Fax:905-887-3974 Pacific AUSTRALIA Philips Consumer Service. Customer Information Centre. 3 Figtree Drive Homebush Bay NSW 2140 Phone: CIC:1300 363 391, PCE Service:1 300-361 392 Fax:+61 2 9947 0063 NEW ZEALAND Philips New Zealand Ltd. Consumer Help Desk 2 Wagener Place, Mt.Albert P.O.
Consumer Information Centers CHINA SHANHAI No. 1102 wuding road, jing an district, 200040 Shanghai, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 NANJING No. 12-2 dong da ying bei, zhu jiang road, 210018 Nanjing, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 HANGZHOU No. 20 jiao gong road, 310012 Hangzhou, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 BEIJING No. 171-3 hai dian road, hai dian district, 100086 Beijing, P.R.
Consumer Information Centers 510070 Guangzhou, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 SHENZHEN Room 603, electronic BLD, No. 30 Shen nan zhong road, 518031 Shenzhen, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 CHANGSHA Room 18, He yi computer city, chao yang road, Changsha, P.R. China Phone: 800 820 5128 (Toll Free) Fax:21-65610647 WUHAN No. 60-66 gui yuan road, hong shan district, 430070 Wuhan, P.R.
Consumer Information Centers INDIA BOMBAY Philips India Customer Relation Centre Bandbox House 254-D Dr.
Consumer Information Centers JAPAN Philips Consumer Electronics 1-11-9,Ebisuminami Shibuya-Ku Tokyo 150 Phone: (03)-3719-2235 Fax : (03)-3715-9992 KOREA Philips Korea Ltd. Philips House C.P.O. box 3680 260-199, Itaewon-Dong. Yongsan-Ku, Seoul 140-202 Phone: 080 600 6600 (Toll Free) Fax:(02)709 1245 MALAYSIA Philips Malaysia Sdn. Berhad Service Dept. No.51,sect.13 Jalan University. 46200 Petaling Jaya, Selagor. P.O.box 12163 50768 Kuala Lumpur.
Consumer Information Centers Fax:(021)-772 1167 PHILIPPINES Philips Electronics and Lighting Inc. 106 Valero St., Salcedo Village Makati, Metro Manilla. Phone: (02)-888 0572 , Domestic Toll Free:1-800-10-PHILIPS or 1-800-10-744 5477 Fax:(02)-888 0571 SINGAPORE Philips Singapore Private Ltd. Consumer Service Dept. Lorong 1,Toa Payoh., P.O. box 340 Singapore 1231 Phone:6882 3999 Fax:6250 8037 TAIWAN Philips Taiwan Ltd. Consumer Information Centre 13F, No. 3-1 Yuan Qu St., Nan Gang Dist.
Consumer Information Centers MOROCCO Philips Electronique Maroc 304,BD Mohamed V Casablanca Phone: (02)-302992 Fax : (02)-303446 SOUTH AFRICA South African Philips. S.V. Div. 195 Main R.D. Martindale., Johannesburg P.O.box 58088 Newville 2114 Phone: (011)-4715000 Fax : (011)-4715020 Middle East DUBAI Philips Middle East B.V. Consumer Information Centre P.O.
Consumer Information Centers file:///D|/EDFU/crt_19/edoc/english/WARRANTY/warcic.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 1 It Takes Only A Moment To PROTECT YOUR INVESTMENT. Congratulations on investing in a Philips product. It’s an important and intelligent decision that’s sure to reward you for many years to come. To ensure you’ll get all of the privileges and protection that come with your purchase, please complete your Warranty Registration Card within the next ten days. SIMPLY MAIL THE CARD BELOW TO RECEIVE ALL OF THESE BENEFITS TO WHICH YOU’RE ENTITLED.
PHILIPS Warranty Card 8/16/02 12:38 PM Page 2 !1375415338! PO BOX 1533 DEPOSIT NY 13754-1533 Please Open Promptly! TIME-DATED MATERIAL a PLEASE APPLY FIRST CLASS STAMP IMPORTANT Warranty Registration Card RETURN THE ATTACHED CARD WITHIN TEN DAYS TO ENSURE YOUR: ✓ Warranty Verification ✓ Owner Confirmation ✓ Model Registration See Inside For Valuable Benefits!
