Technical data

ManualsBrandsPhilips ManualsComputer Hardware107E51-99

17" Auto scan Colour Monitor

Service

TABLE OF CONTENTS

Published by BCU Monitors Printed in Taiwan Copyright reserved Subject to modification Feb 15 2003

3138 106 10261

Description Page

Important Safety Notice ------------------------------- 2

Technical Data ------------------------------------------ 3

Front control & OSD------------------------------------ 4

OSD menu tree------------------------------------------ 5

OSD Adjustments-----------------------------------6~12

Troubleshooting----------------------------------------12

Lock/Unlock, Factory mode, Burn in &

Service mode--------------------------------------------13

Warning and Notes ------------------------------------ 14

Mechanical Instructions ------------------------- 15~16

Wiring Diagram------------------------------------------17

Hex Data of DDC2B--------------------------------18 ~21

Electrical Adjustments --------------------------- 27~ 29

Safety test requirements (Hipot & Ground)------- 30

DDC Instructions -----------------------------------22~26

Description Page

Block Diagram ------------------------------------------31

Video Panel (A) Schematic Diagram ---------------32

Repair Tips ----------------------------------------------39

Exploded View------------------------------------------40

parts list------------------------------41

Spare parts list------------------------------------- 42~44

Repair flow chart----------------------------------- 45~52

Video Panel C.B.A.(A) --------------------------------33

Main Panel-Deflection (B) Schematic Diagram --34

Main Panel C.B.A.(B,C)-------------------------------35

Power Supply (C) Schematic Diagram-------------36

Key Control Panel (D) Schematic Diagram -------37

Key ControlPanel C.B.A. (D) ------------------------38

Recommended

General Product Specification-------------------53~81

General Troubleshooting Guide----------------82~104

REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES

CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.

ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS

AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC

EQUIPMENT CONTAINING HIGH VOLTAGES.

SAFETY NOTICE

Chassis :V20

Horizontal frequencies

30-70kHz

107E51/87

V20 107E5

DDC/Power saving/MPR II/TCO

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Summary of content (81 pages)

PAGE 1
http://jdwxzlw.5d6d.
PAGE 2
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 2 IMPORTANT SAFETY NOTICE V20 107E5 9 Go to cover page Proper service and repair is important to the safe, reliable operation of all PHILIPS Company** Equipment. The service procedures recommended by PHILIPS and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
PAGE 3
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Technical Data Technical Specification* CRT Size and deflection Deflection angle Dot pitch Face treatment Light transmission Phosphor Recommended display area Maximum display area Scanning Horizontal scanning Vertical scanning Video Video dot rate 3 9 Go to cover page Data Storage :17 inch/41cm, flat/square : 90 degrees : 0.27mm with black matrix : Anti-glare, anti-static, : 47%(PHL),46%(CPT),52%(LG), 53.5%(ORION) : P22 : 12.0" x 9.0" / 306 x 230 mm : 12.9" x 9.
PAGE 4
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 4 V20 107E5 9 Go to cover page Front control & OSD Rear view Front View 1. Power in - attach power cable here. 2. Video In - this is a cable which is already attached to your monitor. Connect the other end of the cable to your PC. Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window.
PAGE 5
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 OSD menu tree V20 107E5 9 Go to cover page The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments.
PAGE 6
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 6 V20 107E5 9 Go to cover page OSD Adjustments LANGUAGE The OSD Controls The ON SCREEN DISPLAY shows its settings in one of five languages. The default is English, but you can select French, Spanish, German, or Italian. BRIGHTNESS To adjust your screen's brightness, follow the steps below. Brightness is the overall intensity of the light coming from the screen. A 50% brightness is recommended. 1) Press the appears. button on the monitor.
PAGE 7
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 OSD Adjustments (Continued) ZOOM V20 107E5 7 9 Go to cover page 3) Press the button. The ADJUST HORIZONTAL window appears. ADJUST POSITION should be highlighted. ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below. 1) Press the appears. 2) Press the button on the monitor. The MAIN CONTROLS window button until ZOOM is highlighted. 4) Press the or button to move the image to the left or right.
PAGE 8
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 8 OSD Adjustments (Continued) V20 107E5 9 Go to cover page 2) Press the button until ADJUST VERTICAL is highlighted. 2) Press the button until ADJUST SHAPE is highlighted. 3) Press the button. The ADJUST VERTICAL window appears. ADJUST POSITION should be highlighted. 3) Press the button. The ADJUST SHAPE window appears. ADJUST SIDE CURVE should be highlighted. 4) Press the 4) Press the button. The SIDE CURVE window appears. PINCUSHION should be highlighted.
PAGE 9
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 OSD Adjustments (Continued) V20 107E5 9 Go to cover page Smart Help After returning to MAIN CONTROLS . . . 7) When the trapezoid is adjusted, press the ...to continue to ADJUST SIDE ANGLES, start with step 5 under ADJUST SIDE ANGLES and follow the directions. PARALLELOGRAM or press the SHAPE window. ...to exit completely, press the button twice. 9 button to highlight button to return to the ADJUST ...
PAGE 10
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 10 OSD Adjustments (Continued) V20 107E5 9 Go to cover page 5) Press the button. The ROTATE IMAGE window appears. ROTATE should be highlighted. 4) Press the or button to highlight 9300K for GENERAL USE, 6500K for GAMES, or USER PRESET. 5) Once you have highlighted GENERAL USE or GAMES, press the button to confirm you selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. 6) To adjust the rotation, press the or button.
PAGE 11
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 OSD Adjustments (Continued) 4) Press the or button to select YES or NO. NO is the default. YES returns all settings to their original factory adjustments. V20 107E5 11 9 Go to cover page 4) Press the button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted. 5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted. Smart Help After returning to MAIN CONTROLS . . . . . .
PAGE 12
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 12 V20 107E5 9 Go to cover page OSD Adjustments (Continued), Troubleshooting DEGAUSS Monitor Specific Troubleshooting EXTRA CONTROLS is a set of three features, including DEGAUSS. Degaussing removes electromagnetic build up that may distort the color on your screen. Self-Test Feature Check (STFC) 1) Press the appears. 2) Press the button on the monitor. The MAIN CONTROLS window button until EXTRA CONTROLS is highlighted.
PAGE 13
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Lock/Unlock, Factory Mode, Burn In, Service Mode V20 107E5 13 9 Go to cover page To access factory mode 1. Turn off monitor (don't turn off PC) 2. Press '" " and " " simultaneously on the front control panel,then press " ",wait till the OSD menu with characters V20 107E5 V0.20 20021217 (below OSD menu)" come on the screen of monitor. FrontControl Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey.
PAGE 14
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 V20 107E5 14 X Go to cover page Warning and Notes Warnings Notes 1. Safety regulations require that the unit should be returned in its original condition and that components identical to the original components are used. The safety components are indicated by the symbol . 1. The direct voltages and waveforms are average voltages. They have been measured using the Service test software and under the following conditions : - Mode : 640 * 480 (31.
PAGE 15
Mechanical Instructions V20 107E5 15 9 Go to cover page http://jdwxzlw.5d6d.com/?fromuser=华盛维修 0. General To be able to perform measurements and repairs on the "circuit boards", these unit should placed in the service position first. 1.Remove the rear cover in Fig. 1. -Remove 2 screws as shown -Remove back cover as shown -Remove pedestal as shown 2. Video panel - Disconnect the wire between metal shield of Video panel and CRT neck as shown in Fig. 2. - Disconnect the CRT ground "1703" from Video panel.
PAGE 16
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 16 Mechanical Instructions V20 107E5 Go to cover page 4. Main panel with Bottom Tray -Remove 2 screws for disconnect the Bottom tray as Fig. 5. -Pull the bottom tray on press right and left side clip from fig. 6 to fig. 7. =======> 5. SERVICE POSITION Reconnect connectors, some wires and panels (chassis), service position can be available for DC/AC measurement as shown in Fig. 8. Pull-up Fig. 7 Screw Fig.
PAGE 17
Wiring Diagram V20 107E5 17 9 Go to cover page http://jdwxzlw.5d6d.
PAGE 18
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 18 Hex Data of DDC2B V20 107E5 Go to cover page ********************************************************************** 107E5 Orion Tube EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 000D(HEX.) ID Serial Number : 4D2 (HEX.
PAGE 19
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Hex Data of DDC2B V20 107E5 19 Go to cover page ********************************************************************** 107E5 LG Tube EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 000D (HEX.) ID Serial Number : 4D2 (HEX.
PAGE 20
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 20 Hex Data of DDC2B V20 107E5 Go to cover page ********************************************************************** 107E5 CPT Tube EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 000D(HEX.) ID Serial Number : 4D2 (HEX.
PAGE 21
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Hex Data of DDC2B (Continued) V20 107E5 21 Go to cover page ********************************************************************** 107E5 Philips Tube EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 000D (HEX.) ID Serial Number : 4D2 (HEX.
PAGE 22
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 22 DDC Instructions V20 107E5 Go to cover page 1. General 3. Pin assignment DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect,repaired monitor the serial numbers have to be re-programmed. A.
PAGE 23
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 DDC Instructions (Continued) 4. Configuration and procedure There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores all factory settings and DDC data (EDID code) which is so called Software DDC. The following section describes the connection and procedure for Software DDC application. The main EEPROM can be reprobrammed by enabling "factory memory data write" function on the DDC program (EDID301.EXE). V20 107E5 23 X Go to cover page 3.
PAGE 24
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 24 DDC Instructions (Continued) V20 107E5 Go to cover page Re-programming EEPROM (Software DDC) Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10 PC 4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 13. Fig. 13 Rear view of the monitor To printer port (LTP1) To video card Fig.
PAGE 25
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 DDC Instructions (Continued) Step 5: **Configuration Setup & Enter Factory Mode ** for "write EDID data" 1. Click icon from the tool bar to bring up the Configuration Setup windows again. Then, select "Software DDC only" as shown in Fig. 16. Click "OK". Fig. 16 V20 107E5 25 Go to cover page Step 6: Write DDC data 1. Click (Write EDID) icon from the tool bar to write DDC data. Bring up "Writing 0%~100%, ready" a progressing bar on the left down corner. 2.
PAGE 26
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 26 V20 107E5 Go to cover page DDC Instructions (Continued) Step 9: Load DDC data 1. 2. 3. 4. 5. Click from the tool bar. Select the file you want to open as shown in Fig. 20. Click Open. Access "Factory Mode" and enable "Software DDC only" as shown in Fig. 17 & Fig. 16. Write EDID (click ). Note 2 : In Factory Mode: Read/Write DDC data Before Read/Write EDID code, please confirm that the Software DDC only was enabled as shown in Fig. 23. Fig. 20 107E5 V20.
PAGE 27
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Electrical Adjustments 0. General 1. This monitor has 8 factory-preset modes as below. 720 x 400 31.5 kHz/70 Hz 640 x 480 31.5 kHz/60 Hz 640 x 480 43.3 kHz/85 Hz 800 x 600 46.9 kHz/75 Hz 800 x 600 53.6 kHz/85 Hz 1280 x 960 60.0 kHz/60 Hz 1024 x 768 68.7 kHz/85 Hz 1280 x 1024 64.0kHz/60Hz V20 107E5 27 Go to cover page 5. To access factory mode 5.1 Turn off monitor (don't turn off PC) 5.
PAGE 28
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 28 V20 107E5 9 Go to cover page Electrical Adjustments (Continued) 7. Alignment of Vg2 cut-off point, white tracking Equipment : 1. Video Test Generator-801GC (Quantum Data) 2. Color-analyzer (Minolta CA-100) VG2 [(screen), at the bottom of the L.O.T.]. 7.1 Apply a video signal in the 1024 x 768 with 68.7 kHz/85 Hz mode, select the "full white pattern" (sizes 306 x 230 mm). * Use color-analyzer (Minolta CA-100) to adjust R/G/B cutoff and gain.
PAGE 29
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Electrical Adjustments (Continued) V20 107E5 29 Go to cover page 8. Focus adjustment Apply a signal of " ME " pattern. at 68.7 kHz/85 Hz mode set the brightness to mid-position , contrast to max - position and adjust the focus for optimal sharpness in the area within 2/3 from the screen center. 9. Loading DDC code The DDC HEX data should be written into the EEPROM (7802) by EDID301.EXE Program(3138 106 10103) and software DDC Alignment kits (4822 310 11184).
PAGE 30
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Safety test requirements V20 107E5 30 Go to cover page All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both Hipot and Ground Continuity testing. HI-POT TEST INSTRUCTION 1. Application requirements 1.1 All mains operated products must pass the Hi-Pot test as described in this instruction. 1.
PAGE 31
Block Diagram http://jdwxzlw.5d6d.
PAGE 32
Video Panel Schematic diagram V20 107E5 http://jdwxzlw.5d6d.com/?fromuser=华盛维修 9 Go to cover page A 0.9 1.4 1.2 A2 A3 1.7 54.8 A5 54.3 A6 55.1 4.2 1.5 A1 A4 1.3 1.5 1.7 1.5 1.7 3.8 1.7 2 5 1.9 5.9 5 -65.9 53.7 47.8 49.3 家电维修资料网，免费下载各种维修资料 176.
PAGE 33
Video Panel C.B.A.(A) V20 107E5 http://jdwxzlw.5d6d.
PAGE 34
Deflection- Main Panel Schematic diagram V20 107E5 http://jdwxzlw.5d6d.com/?fromuser=华盛维修 9 Go to cover page B 3.8 B11 132.6 B2 B3 5 26.9 5 B1 -2.7 6.2 2.7 3.8 28 28 26.9 B10 5.1 B9 7.8 28 28 B13 4.2 2.8 2.8 B8 3.4 B4 B5 60.7 72.2 7.8 3.4 B7 5 2.8 1.8 4.7 3.7 B12 2.3 27 3.7 B6 5.3 5.3 B14 B15 50.4 131.6 1 4.9 4.6 38 B16 2.1 5 2 25 138.8 138.7 2.4 12.6 B17 12.5 1.2 1.2 -12 1.2 8.2 3.8 B18 82.2 4.3 5.8 2.4 家电维修资料网，免费下载各种维修资料 7.
PAGE 35
Main Panel C.B.A.(B) V20 107E5 http://jdwxzlw.5d6d.
PAGE 36
Deflection- Main Panel ( Map & Waveform) V20 107E5 http://jdwxzlw.5d6d.
PAGE 37
http://jdwxzlw.5d6d.
PAGE 38
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 38 V20 107E5 Go to cover page Key Control Panel C.B.A.
PAGE 39
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Repair Tips 0. Warning All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the unit via a wrist wrap with resistance. Keep components and tools also at the same potential ! 1. Servicing of SMDs (Surface Mounted Devices) 1.
PAGE 40
http://jdwxzlw.5d6d.
PAGE 41
http://jdwxzlw.5d6d.
PAGE 42
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Spare Parts List V20 107E5 42 Go to cover page Parts List CTV : 107E51/87 0001 0003 0004 0042 313812753221 313812753211 313812753231 313810459461 FRONT CABINET ASSY PEDESTAL ASSY CHIN ASSY BACK COVER 1050 930187980323 CRTM41EHN323X160/G372BV (LGPD) Various 0450 0451 0452 0454 0601 313810661791 313810661801 313810661811 313810656581 313811704781 CARTON CUSHION - TOP CUSHION - BTM PE BAG E-D.F.U.
PAGE 43
http://jdwxzlw.5d6d.
PAGE 44
http://jdwxzlw.5d6d.
PAGE 45
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Repair Flow Chart 45 V20 107E5 9 Go to cover page A. Power Supply Failure 1. Sympton : no startup sound LED light off check 7102 pin8 Ok 100V 2V NO check 1101/6101/ 7101/2106 Ok check 7102 pin 5=2.4V NO Ok replace 7102 check 6165/3107/ 3105/7101 NO check 7105/3125 3112/6105 check replace 7102 2.
PAGE 46
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 46 Repair Flow Chart (Continued) V20 107E5 9 Go to cover page rough check for R,G, B 1. video input= 0.7V 2. 7301video output =2.5V 3. 7701 video output > 35Vpp B.Video Repair Flow check blanking 7501 pin3 Ok 1.Sympton : (with wite pattern) no picture green LED on check heater = + 6.3V check EHT=25KV Ok check VG1 < -150V No No check R,G,B output 30<2713<80 30<2711<80 30<2708<80 Ok check Xray prot.
PAGE 47
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Repair Flow Chart (Continued) V20 107E5 9 Go to cover page C. Horizontal deflection output repair flow : 1. Sympton : without H-deflection. check Hsync 7606 base check 180V replace 5610 2. Sympton : East /West corr. 3. Sympton : H-linearity (full freq.
PAGE 48
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 48 V20 107E5 9 Go to cover page D.
PAGE 49
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Repair Flow Chart (Continued) E. CPU check list Basic Check check cpu pin6= 5V pin9/pin8=12MhZ pin7=gnd 31. H-EHT H size compensation for the load variance 36,37,38(Q3,Q2,Q1) S-cap switch 33,34,40,41 Hsync / Vsync check Q1-Q2 Pin36~38 low : 0 hi :1 check sync. Hsync_in=pin40 Vsync_in=pin41 Hsync_out=pin34 Vsync_out=pin33 18. Blanking (mute) check pin18 normal : low change timing : Hi 20, 27,22 P.S. LED pin 27 STBY pin 22 OFF 23.
PAGE 50
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 50 V20 107E5 9 Go to cover page Repair Flow Chart (Continued) check output from 0V to 5V 4. Rotation check output from 0V to 5V 30. ABL-CON check key Enter,Up,Down,Left,Right keys 21,29 Keypad check 3811, 2812 3825~3820 check pin24 1.no H/V sync & IF cable pin5 floating - show msg. 2.H/V sync exist & IF cable pin5 to ground - normal 3.H/V sync non-exist & IF cable pin5 to gnd -power saving 4.
PAGE 51
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 Repair Flow Chart (Continued) Basic check Vcc > 9V during startup F. TDA9112a Check List 12. HFLB (from H.defl) 25. Xray (from LOT) 14.15.16,28 B+ control 9 Go to cover page Pin12 CLBL=hi Pin3= Hunlock = floating Pin5 = Hpll2 = 0V pin6 = HDRV = floating pin8 = BDRV = flaoating Pin23 = Vout2 = floating pin16 = CLBL= Hi a pin14 amplify pin5 and it compare to pin4 b. Pin15 generate the saw_tooth wave c. Pin16 input voltage for the square output waveform d.
PAGE 52
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 52 V20 107E5 9 Go to cover page 3. Hunlock 30. IIC scl = hi 31 IIC sda = hi 18 EHT_compen. Repair Flow Chart (Continued) Hunlock pin is floating while pll1(pin9) is unlock in searching mode the initial sequence of IIC IC 7501,7301 compensate for the V_size owing the load variation 19,20,22 VAGC,VREF,VCAP Pin19 determin the AGC Pin20,pin22 determin frequency 4,6,8,9 Hpll1,Hbuf,Href, Hcap Pin9 determin the pll1 loop filter pin 4,6,8 H-Freq working range 5.
PAGE 53
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION V20 107E5 9 Go to cover page 17" 107E5 ;70KHz General Specification (Sheet 590) ===================================================== FEATURES / BENEFITS - EXTREMELY HIGH MTBF (OVER 75K HRS, EXCLUDING CRT) - PROFESSIONAL LOOK, WITH NON-FLAMMABLE CABINET (94V-0) - USER'S CONTROLS . FRONT MOUNTED CONTROLS FOR EASY ACCESS - BETTER DISPLAY PERFORMANCE . FINER CRT DOT PITCH (0.27 MM) . FULL SCREEN SIZE APPLICATION . REAL MULTI-FREQ.
PAGE 54
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 54 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION INDEX ========= 1.0 Introduction 2.0 2.1 General description General condition 3.0 3.1 3.1.1 3.1.2 3.1.3 3.2 3.2.1 3.2.2 3.3 3.4 3.5 3.6 3.6.1 3.6.2 3.7 3.8 3.9 3.10 3.
PAGE 55
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION 5.0 5.1 5.2 5.2.1 5.2.2 5.3 Mechanical characteristics User controls ( at front) Connector and cables Power Cord Signal Cable Tilt and swivel base 6.0 6.1 6.1.1 6.1.2 6.2 6.2.1 6.3 6.3.1 6.3.
PAGE 56
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 56 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION 1.0 Introduction This document is related to the 17" AUTOSCAN (VGA above and Max. resolution 1280X1024 by 60HZ refresh) color monitor for world-wide destination. 2.0 General description The AUTOSCAN analog color monitor is specified as a display peripheral within an IBM PC, PS/2 ,VGA and advance VGA compatible system.
PAGE 57
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION 3.1.2 V20 107E5 9 Go to cover page Signals input The input video signals are applied to the display device through a video cable which is fixed to the monitor (standard cable length 1.45M ). Video input cable : 15 pin D-shell male connector type AMP 211350-1(3 rows) or equivalent, with pin assignment as follows : Pin assignment of 15P D-SUB connector Pin nbr. P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 3.1.
PAGE 58
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 58 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION Factory preload modes : 14 Resolution 9. 640 x 350 10. 640 x 350 11. 640 x 480 12. 640 x 480 13 640 x 480 14. 720 x 400 15. 800 x 600 16. 800 x 600 17. 800 x 600 18 .832 x 624 19.1024x 468 20.1024x 768 21.1152x 864 22.1024x 768 3.2 H. freq. 31.5 37.9 37.5 37.9 50.6 37.9 37.9 48.1 63.9 49.7 48.4 56.5 67.5 60.0 V. freq. KHz 70Hz KHz 85Hz KHz 75Hz KHz 72.
PAGE 59
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION V20 107E5 9 Go to cover page TIMING FOR 107E5 70K COLOR MONITOR REFERENCE PATTERN GENERATOR : CHROMA 2135 * According VESA version 1.0 release 0.6p Factory preset modes TABLE 1: 31.469 KHz/70.087 Hz, 720 X 400, pixel=28.325 MHz Horizontal Frame border Total size Display size Rear porch Sync width Sync.polarity Vertical = 0 Frame border = 31.774 us Total size = 25.422 us Display size = 1.907 us Rear porch = 3.813 us Sync width = Sync.
PAGE 60
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 60 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION TABLE 5: 53.674 KHz/85.061 Hz, 800 X 600, pixel=56.250 MHz Horizontal Frame border Total size Display size Rear porch Sync width Sync.polarity = 0 = 18.631 = 14.222 = 2.702 = 1.138 = + Vertical Frame border us Total size us Display size us Rear porch us Sync width Sync.polarity = 0 = 11.756 ms = 11.179 ms = 0.503 ms = 0.056 ms = + TABLE 6 : 60.
PAGE 61
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION V20 107E5 9 Go to cover page Factory preload modes TABLE 9: 31.469KHz/70.087 Hz, 640 X 350, pixel=25.175MHz Horizontal Frame border Total size Display size Rear porch Sync width Sync.polarity Vertical = 0 Frame border = 31.778 us Total size = 25.422 us Display size = 1.907 us Rear porch = 3.813 us Sync width = + Sync.polarity = 0 = 14.268 ms = 11.122 ms = 1.907 ms = 0.064 ms = - TABLE 10: 37.861KHz/85.08 Hz, 640 X 350, pixel=31.
PAGE 62
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 62 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION TABLE 13: 50.625 KHz/100.049 Hz, 640 X 480, pixel=40.5MHz Horizontal Frame border Total size Display size Rear porch Sync width Sync.polarity Vertical = 0 = 19.752 = 15.802 = 1.975 = 1.580 = - Frame border us Total size us Display size us Rear porch us Sync width Sync.polarity = 0 = 9.995 ms = 9.481 ms = 0.435 ms = 0.059 ms = - TABLE 14: 37.927 KHz/85.039 Hz, 720 X 400, pixel=35.
PAGE 63
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION V20 107E5 9 Go to cover page TABLE 17: 63.92KHz/100 Hz, 800 X 600, pixel=67.5MHz Horizontal Frame border Total size Display size Rear porch Sync width Sync.polarity Vertical = 0 Frame border = 0 = 15.644 us Total size = 9.997 ms = 11.852 us Display size = 9.387 ms = 2.370 us Rear porch = 0.548 ms = 0.948 us Sync width = 0.047 ms = + Sync.polarity = + TABLE 18: 49.714KHz/74.534 Hz, 832 X 624, pixel=57.
PAGE 64
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 64 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION TABLE 21: 67.5 KHz/75Hz, 1152 X 864, pixel=108MHz Horizontal Frame border Total size Display size Rear porch Sync width Sync.polarity Vertical = 0 = 14.815 = 10.667 = 2.370 = 1.185 = + Frame border us Total size us Display size us Rear porch us Sync width Sync.polarity = 0 = 13.333 ms = 12.8 ms = 0.474 ms = 0.044 ms = + TABLE 22: 60.03 KHz/75 Hz, 1024 X 768, pixel=78.
PAGE 65
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION 3.2.1 Horizontal scanning Scanning frequency H-shift range 3.2.2 Vertical scanning : 50 - 160 Hz : 10 mm min. (for preset modes only) Power supply The display device maintains the specified performance in the range described as bellows : Type Mains current Mains Voltage Mains freq. 120V version 1.0A Max. 90 - 132 VAC 60 +/1 3 Hz 230V version 0.6A Max. 198 - 264 VAC 50+/- 3 Hz Full Range 1.5A Max.
PAGE 66
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 66 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION 3.6 RGB Amplifier 3.6.1 Video amplifiers Dot Rate Over / undershoot : 108 MHz : 15% Max. (Transient response) : 5% Max.(pulses of 0.70H) : 5% Max. Sag Black level shift 3.6.2 Brightness and Contrast Reference mode 68.7 KHZ/85 HZ full white pattern. DISPLAY LIGHT OUTPUT Brightness Light output (full white) Contrast Minimum Minimum Center Maximum not visible 30+/- 5 FL.
PAGE 67
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION 3.10 V20 107E5 9 Go to cover page Low emission requirements.(MPRII/TCO99/TCO95) -------------------------------------------------------------Items Band I ELF (rms) Band II VLF (rms) Alternating Electric MPRII < 25 V/M MPRII < 2.5 V/M Field TCO < 10 V/M TCO < 1.0 V/M Magnetic Field MPRII < 250 nT TCO < 200 nT Electrostatic Potential MPRII < 25 nT TCO <25 nT <+/- 500 V Band I : 5 to 2K HZ. Band II : 2K to 400K HZ.
PAGE 68
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 68 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION Width Height 4.3 : 306 +/- 3 mm : 230 +/- 3 mm Image centering deviation (For preset modes only) With respect to fig. 2, the target relationships are the following : |A- B| <= 5 mm |C- D| ,= 5 mm Note : This centering is adjustable by the end-user. 4.4 Picture shift control range (For preset modes only) H-shift range : 10 mm min. V-shift range : 10 mm min. 4.5 Picture tilt With respect to Fig.
PAGE 69
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION 4.8 V20 107E5 9 Go to cover page Mis-convergence The maximum convergence error to be measured on a white spot or white display line to represents the maximum distance between the energy centers of any two primary colors. (See Fig. 6) For VGA mode <45KHz Zone B: 0.4mm. CONVERGENCE SPEC. 4.9 Zones 0.27 mm CRT Zone C 0.15 mm Zone A 0.25 mm Zone B 0.35 mm Focus check ( 68.
PAGE 70
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 70 9 V20 107E5 Go to cover page 4.13 GENERAL PRODUCT SPECIFICATION Purity Test patterns : Full white / Red / Green / Blue. Conditions : As stated in item 4.0, the purity must be checked under specific destinations of earth magnetic environments and the monitor to be well degaussed. After warming-up time of 30 min. , no color stains may occur in above four patterns. 4.
PAGE 71
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION 5.2.2 V20 107E5 9 Go to cover page Signal cable Length of video : 1.45 m +/- 50 mm flying with 15 pin PS/2 D-shell socket 5.3 Tilt and swivel base Tilt angle : 5 forward and 15 backward Swivel rotation : 90 leftward or rightward 6.0 Environmental characteristics The following sections to define the interference and susceptibility condition limits that might occur between external environment and the display device. 6.
PAGE 72
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 72 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION TRANSPORTATION TEST OF BU-MONITORS TEST ITEM 1. PACKAGED TEST: 1.1 Packaged random vibra. test 1.2 Drop test l l l l 1.3 Cold drop test (Only for reference) STANDARD REFERENCE TEST CONDITION l l l Ref. ASTMD-4169 5~200 Hz, 0.73 Grms, 30 MIN/ AXIS, 3 AXES., Gross weight drop height: 9.53~18.
PAGE 73
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 GENERAL PRODUCT SPECIFICATION V20 107E5 9 Go to cover page 6.3.2 EMI/EMS Can comply with FCC part 15,DOC C108.8 and EN55022. EMS EN61000-4-3 (80% 1KHz AM modulation) Picture jitter 2mm. 7.0 Safety tests 7.1 Dielectric strength (Hi-pot test) According to IEC950, UL1950 and CSA 22.2 No 950 7.2 Resistance for protective earthing According to IEC950 7.3 Leakage current According to IEC950, UL1950 and CSA22.2 No. 950 7.
PAGE 74
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 74 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION 9.0 Reliability 9.1 Mean time between failures MTBF to be calculated according to Military standard MIL-HDBK-217C. MTBF 75,000 Hours (Excluding CRT) TOTAL HRS (POWER ON) X TOTAL SETS PRACTICE of MTBF = ------------------------------------------------------NBR. OF FAILURE SETS 10.0 Quality assurance requirements 10.1 Acceptance test According to MIL-STD-105D level II, AQL : 0.4 (Major) : 1.
PAGE 75
http://jdwxzlw.5d6d.
PAGE 76
http://jdwxzlw.5d6d.
PAGE 77
http://jdwxzlw.5d6d.
PAGE 78
http://jdwxzlw.5d6d.com/?fromuser=华盛维修 9 V20 107E5 Go to cover page GENERAL PRODUCT SPECIFICATION D A C B 306 mm A=B=C=D < 2.
PAGE 79
http://jdwxzlw.5d6d.
PAGE 80
http://jdwxzlw.5d6d.
PAGE 81
http://jdwxzlw.5d6d.