Introduction The PHILIPS 1058 color monitor displays sharp and brilliant images of text and graphics with a maximum resolution up to 1024x768 pixels. It is optimal for Windows, spread sheets, and any other application. ‘This monitor automatically scans horizontal frequencies from kHz to KHz, and vertical frequencies from 850Hz to 110Hz.
Note: If you experienced your monitor display is changing from color to mono, it's possible that you are using & non-VASE-DDC-standard video card. Please consult with your local Philips dealer for more information. As an Energy Star Mariner, PHILIPS, has determined that this product meets the Energy Star guidelines for energy efficiency. iBM, IBM PC and Power PG are registered trademarks of International Business Machines Corporation.
Safety precautions and maintenance # Disconnect the monitor from the mains supply if the monitor is not to be used for an extended period of dime. + Do not flattering jo remove the back cover, as you will be exposed to a shack hazard, The back cover should only be removed by qualified service personnel, + Do not place objects on top of the monitor cabinet, which could fall into certs or which could cover them and prevent proper cooling of the monitor's electronics devices.
Important: Please refer to the user’'s manuals of your computer and video adapter to make sure these equipment are properly installed and configured before installing the monitor. Positioning / Ventilation + Avoid exposing the monitor ta direct sunlight, stoves or any other heat sources. # To prevent overheating, make sure that the ventilation openings of the monitor are not covered. + Keep moisture and ‘dust away.
Connection important: Please make sure the AC power to your computer is “OFF” before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal in fury as well as permanent damage to your computer equipment. Intel Based platform: 386, 486, Pentium, or other compatibles: « Connect the monitor fo the computer using the supplied interface cables.
Connection to the mains {Rear of tho monitor) (Mains cor) Connecting to the mains This monitor is set to operate at a mains supply of 100-240 vols AC {15C1320W); 220-240 vols AC {15C13205). If the mains voltage in your home is not between this, consult your dealer. Connect one end of the mains cord fo the mains socket at the rear of monitor, and the other end to the mains supply. The monitor will be operating in power saving mode if you switch on your monitor without signal input from PC.
Front Control locations and functions For an optimized adjustment of the picture following controls are available at the front. O Pow Er. ® Press this knob, the green LED lights and the power is ON, ® Press this knob again, the green LED disappears and the power is OFF. () CONTRAST ® Used to adjust the picture contrast level. ¢ BRIGHTNESS @ Used to adjust the overall screen brightness as a compensation for ambient fight. " or ® Press adjust the selected function.
The function pads: H-Shirt : to adjust the horizontal position of the image. H-Size : to adjust the horizontal amplitude of the image. V-shift 1 to adjust the vertical position of the image. V-size 1 fo adjust the vertical amplitude of the image. Second level of the function pads: \7 Trapezoid : to correct the trapezoid distortion of the image. 1 Pincushion : to correct the barrel distortion of the image & Recall 1 to recall original factory preset mode Remarks: 1.
m Adjustment “The monitors per-set with 8 modes for optimal display size and centering as indicated in the following table: Resolution | Horizontal | Vertical Mode ({dots x fines)! Remark VGA 840 x 350 31.5 70 Interrelated VGA 840 x 400 315 70 Non-interlaced VGA 840 x 480 315 a0 Non-interlaced VESALIUS | 640 x 480 375 75 Non-interlaced VESALIUS {800 x 600 378 60 Nor-interlaced VESALIUS 1800 % 600 468 75 Nor-interlaced VESALIUS 11024 x 768 48.3 [ Non-interlaced VESALIUS 1800 x 600 53.
{B} Power Management Signaling Power Management Definition VASE DIMS POWER SAVING STATES MODE VIDEO SYNCHRONY-SYNC | POWER USED | POWER SAVING(%) oN Actives Yes | Yes < 75 Watts 0% Stand-by| Blanked! No Yes < 18 Walls > 80% Suspend | Blanked | Yes Nao < 15 Watts > 80% OFF Blanked Walt > 90 % Note: The video will be blanked and the power LED color will change into following colors whenever the monitor goes into power management talus.
Technical information ) General: Picture tube Screen area + inch (38.1 om), 90° deflection, non glare, black matrix light transmission 57%, phosphor P22 medium short, doodad pith 0.28 mm.
(1Y) Pin assignment: (1} The 15-pin D-sub connector {male) of the signal cable (IBM systems}): Pin No. | Assignment Pin No. | Assignment 1 Red video input 9 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 Identification output 4 Identification output ~ connected to pin 10 Connected to pin 10 12 Serial data line (SDA) 5 Ground 43 |H. Sync/H+V 8 Rad video ground 14 V.
Federal Communication Commission (FCC Statement) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant w0 Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This : equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may . cause harmful interference to radio communications.
Information for Users in the U. 8. Fortuitousness 115V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or ST three conductor cord a maximum of 15-feet in length and a parallel blade, grounding type attachment plug rated 15 4, 125 V. For units set at 230 V: . Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet in length and a tandem blade, grounding type attachment plug rated 15°A, 250 V. Information for Users outside the U.S.
