English 10— Introduction This dual VGA, YGA plus collar mentor displays sharp images of ext and graphics with a maximum resolution up to 1024x768 pixels by interlaced (XGA} mode. This monitor automatically scans vertical frequencies between 50 Hz and 100 Hz. You may use this color monitor with a computer which utilizes 1BM PC, PCT, PC/AT, PS/2 or other compatible system that is fitted with a VGA interface card.
Federal Communications Commission (FCC Statement) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against teleconferencing naresidentialinstallation. Thisequipmentgenerates, uses candidate radio frequency energy and, institutionalized used in accordance with the instructions, may cause harmful interference 1o radii communications.
0 TR Safety precautions and maintenance 4 Disconnect the monitor from the mains supply if the monitor is not to be used for an extended period of time. 4 Do not attempt to remove the back cover, as you will be exposed to a shock hazard. The back cover should only be removed by qualified service personnel. 4 Do not place objects on top of the monitor cabinet, which could fall into vents or which could cover them and prevent proper cooling of the monitor's electronics.
Installation NOTE: Before installing this monitor, please refer io the user's guides of your computer and video adapter to make sure if these equipment require any change of setting. Positioning/Ventilation WARNING: WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE. Do not place the monitor near a heat source. To prevent overheating, ensure that the ventilation openings of the monitor are not covered.
Connection to the computer NOTE: Please be sure the AC power to your computer is “OFF” before connecting or disconnecting any display peripheral. Failure to do so may cause serious personal injury as well as permanent damage to your computer equipment. IBM PC, TWIXT, PC/AT, PS/2, or the compatibles: Connect the fixed 15-pin D-sub connector of the video signal cable o the computer at the video connector on the video card, and fix it firmly with the screws on the plug.
0O — Connection to the mains (Rear of the monitor) (sins cord) Connecting to the mains This monitor is set fo operate at a mains supply of 100-240 vols AC. if the mains voltage in your home is not between this, consult your dealer.
A Adjustment S e For an optimized adjustment of the picture following controls are available at the front. @ POWER ® Press this knob, the green LED lights and power is ON. ® Press this knob again, the green LED disappears and the power is OFF. ® The green LED will flash when the power management system has been activated. (» CONT. ® Used fo adjust contrast. & BRIGHT. ® Used to adjust brightness. H-SIZE ® Used to adjust image width. (O H-SHIFT ® Used {o adjust image position horizontally.
Adjustment moat ‘The monitor is per-set on 800X600 mode as default SAGA Mode. For an imitative mode, L.e. 1024x768, the following controls are available at the rear to optimize adjustment of the picture: (The default mode will be replaced by re-adjust per-set) H-SIZE ® Used to adjust image width, (DD H-SHIFT & Used to adjust image position horizontally. @ v-size ® Used to adjust image height. & v Shift ® Used to adjust image position vertically.
Technical information (1) General: Picture tube : 14 inch, 50° deflection, non-glare, back matrix, light transmission P22 medium shout, dotted pitch 0.28 mim. Serene area : 260 mun (H) x 188 mm (V) Line (Horizontal) frequency : KHz Raster (Vertical) frequency : 50 100 Hz (automatically) Mains voltage : 100 -240 VAC, 60-50 Hz Power consumption : 80 Walt max. Dot rate : MHz Pedestal : Tilt 5° forward, 15° backward; swivel 30° left or right.
{iV) Pin assignment: The 15-pin D-sub connector {male) of the signal cable (IBM systems): Pin No. | Assignment Pin No. | Assignment 1 Red video input 8 No pin 2 Green video input 10 Magic ground 3 Blue video input i Identical cutout 4 Identical output connected fo pin 10 Connected to pin 10 12 No pin 5 Self-test input 13 H. Synge 8 Red video ground 14 | V.
Information for Users in the U.S. For uni t a v: Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet in length and a parallel blade, grounding type attachment plug rated 15 A, 125 V. For units set at 230V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a maximum of 15-feet in length and a tandem blade, grounding type attachment plug rated 15 A, 250 V. I son f rs outside the U.
