Specification

Application
The Bodine ELI-S-10 Emergency Lighting Inverter
works in conjunction with fluorescent or LED
fixtures to create an emergency lighting system.
The ELI-S-10 operates a maximum load of 10 Watts
at unity power factor. It allows the connected
fixture(s) to be on, off, switched or dimmed
without affecting emergency operation. Each
unit consists of batteries, charger and electronic
circuitry in one steel case. The ELI-S-10 provides
power to the input side of the fixture, including
the AC ballast/driver. The ELI-S-10 is NOT suitable
for use with HID lighting nor is it rated for outdoor
mounting location.
Operation
Upon failure of normal power, the ELI-S-10
instantly begins providing emergency power to
the connected lighting load for a minimum of
90 minutes. A low voltage disconnect circuit
protects the inverter batteries from damage by
deep discharge during prolonged power failures.
When normal power is restored, the ELI-S-10
automatically returns to charge mode. The battery
capacity is fully restored in 24 hours.
Dimming
The ELI-S-10 features a dimming control output of
0-10 volts. This dimming capability allows a lighting
load with up to a 50W maximum input power to
be dimmed to a 10VA maximum emergency output
power. The emergency mode output dimming
voltage is automatically controlled by the ELI-S-10
electronic circuitry to maintain up to 10VA output
throughout the loss of AC power. The ELI-S-10
passes the normal room dimming control signal
(0-10V) during normal operation (AC mains on) so
normal dimming operation of the luminaire is not
affected.
Installation
The ELI-S-10 does not affect normal fixture
operation and may be used with a switched or
unswitched fixture. It can be installed on top of or
close proximity to the fixture.
Code Compliance
The ELI-S-10 has been tested by Underwriters
Laboratories in accordance with the standards set
forth in UL 924, “Emergency Lighting and Power
Equipment”. The ELI-S-10 is UL Listed for field
installation. Emergency illumination time exceeds
the National Electrical Code (NEC), Life Safety
Code (NFPA-LSC), National Building Code of
Canada (NBC), National Fire Code of Canada (NFC)
and UL 90-minute requirements.
Emergency Illumination
The ELI-S-10 supports 10VA of emergency power
for a minimum of 90 minutes.
Specification
Emergency lighting shall be provided by using a
standard fixture or group of fixtures powered
with a Bodine ELI-S-10 inverter. The ELI-S-10
unit consists of batteries, and electronic battery
charging and output circuitry contained in one
metal case. The ELI-S-10 unit shall be capable of
powering dimmable fluorescent and/or LED lighting
fixtures rated at up to 50W of input power at 0°C
to 50°C for a minimum of 90 minutes by the use
of 0-10V dimming control. The ELI-S-10 shall allow
the emergency fixture to be on, off, switched or
dimmed without affecting emergency operation.
The ELI-S-10 unit shall exceed emergency
standards set forth by the current NEC and the
Canadian Electrical Code.
This device complies with Part 15 of the FCC Rules and
meets California Energy Commission Title 20 efficiency
requirements. It shall be UL Listed for the US and
Canada, suitable for damp locations, and warranted
for a full five years from date of manufacture.
Warranty
The ELI-S-10 is warranted for five (5) years from the
date of manufacture. This warranty covers only
properly installed Bodine ELI-S-10 emergency units
used under normal conditions. For the warranty
period, Signify will, at its option, repair or replace
without charge a defective inverter provided it is
returned to the factory transportation prepaid
whereas an inspection will be conducted to determine
if the unit is defective under the terms of the
warranty. Repair or replacement, as stated above,
shall constitute the purchaser’s exclusive warranty,
which does not extend to transportation, installation,
labor or any other charges; nor does it apply to
any equipment of another manufacturer used in
conjunction with the inverter.
ELI-S-10 10VA Pure Sine Wave Nano Inverter
V : 120-277V 50-60Hz
in AC,
I : 0.11A Max
in
P : 9W Max
in
V : 120/277V 60Hz
out AC,
T : 0°C to 50°C
amb
P : 10VA Max
out
Emergency Lighting Inverter
ELI-S-10
ENGINEERING SAMPLE
ENGINEERING
SAMPLE
Technical Information 1.888.263.4638
Collierville, TN
Assembled in USA
Operates a 0-10V DC dimmable LED Driver in the
emergency mode for a minimum of 90 minutes.
For engineering and test purposes only.
ELI-S-10
LED Driver
LED
LED
Earth Ground
Emergency DIM+ (VIOLET/PINK)
Emergency DIM- (GRAY/PINK)
Emergency Neutral (RED/WHITE)
Emergency HOT (RED/BLACK)
HOT (RED)
Neutral (WHITE)
0-10V DIM- (GRAY)
Switched HOT (BLACK)
0-10V DIM+ (VIOLET)
(BROWN)
(VIOLET)
Test Switch-
(BROWN/WHITE)
Test Switch+
(VIOLET/WHITE)
Unit Engage (BLUE)
Unit Engage (BLUE)
XX°C max
Tc
V : 120-277V 50-60Hz
in AC,
I : 0.11A Max
in
P : 9W Max
in
V : 120/277V 60Hz
out AC
,
T : 0°C to 50°C
amb
P : 10VA Max
out
Emergency Lighting Inverter
ELI-S-10
ENGINEERING SAMPLE
ENGINEERING
SAMPLE
Technical Information 1.888.263.4638
Collierville, TN
Assembled in USA
Operates a 0-10V DC dimmable LED Driver in the
emergency mode for a minimum of 90 minutes.
For engineering and test purposes only.
ELI-S-10
LED Driver
LED
LED
Earth Ground
Emergency DIM+ (VIOLET/PINK )
Emergency DIM- (GRAY/RED)
Emergency Neutral (RED/WHITE)
Emergency HOT (RED/BLACK)
HOT (RED)
Neutral (WHITE)
0-10V DIM- (GRAY)
Switched HOT (BLACK)
0-10V DIM+ (VIOLET)
(BROWN)
Test Switch-
(BROWN/WHITE)
Test Switch+
(VIOLET/WHITE)
Unit Engage (BLUE)
Unit Engage (BLUE)
XX°C max
Tc
V : 120-277V 50-60Hz
in AC,
I : 0.11A Max
in
P : 9W Max
in
V : 120/277V 60Hz
out AC,
T : 0°C to 50°C
amb
P : 10VA Max
out
Emergency Lighting Inverter
ELI-S-10
ENGINEERING SAMPLE
ENGINEERING
SAMPLE
Technical Information 1.888.263.4638
Collierville, TN
Assembled in USA
Operates a 0-10V DC dimmable LED Driver in the
emergency mode for a minimum of 90 minutes.
For engineering and test purposes only.
ELI-S-10
LED Driver
LED
LED
Earth Ground
Emergency DIM+ (VIOLET/RED)
Emergency DIM- (GRAY/RED)
Emergency Neutral (RED/WHITE)
Emergency HOT (RED/BLACK)
HOT (RED)
Neutral (WHITE)
0-10V DIM- (GRAY)
Switched HOT (BLACK)
0-10V DIM+ (VIOLET)
(BROWN)
Test Switch-
(BROWN/WHITE)
Test Switch+
(VIOLET/WHITE)
Unit Engage (BLUE)
Unit Engage (BLUE)
XX°C max
Tc
V : 120-277V 50-60Hz
in AC,
I : 0.11A Max
in
P : 9W Max
in
V : 120/277V 60Hz
out AC,
T : 0°C to 50°C
amb
P : 10VA Max
out
Emergency Lighting Inverter
ELI-S-10
ENGINEERING SAMPLE
ENGINEERING
SAMPLE
Technical Information 1.888.263.4638
Collierville, TN
Assembled in USA
Operates a 0-10V DC dimmable LED Driver in the
emergency mode for a minimum of 90 minutes.
For engineering and test purposes only.
ELI-S-10
LED Driver
LED
LED
Earth Ground
Emergency DIM+ (VIOLET/RED)
Emergency DIM- (GRAY/RED)
Emergency Neutral (RED/WHITE)
Emergency HOT (RED/BLACK)
HOT (RED)
Neutral (WHITE)
0-10V DIM- (GRAY)
Switched HOT (BLACK)
0-10V DIM+ (VIOLET)
(BROWN)
Test Switch-
(BROWN/WHITE)
Test Switch+
(VIOLET/WHITE)
Unit Engage (BLUE)
Unit Engage (BLUE)
XX°C max
Tc
Wiring Schematic
LED Load
© 2019 Signify Holding. All rights reserved. This document contains information
relating to the product portfolio of Signify which information may be subject to
change. No representation or warranty as to the accuracy or completeness of the
information included herein is given and any liability for any action in reliance thereon
is disclaimed. All trademarks are owned by Signify Holding or their respective owners.
ELI-S-10.spec.L8000044 09/19
Signify North America Corporation
200 Franklin Square Drive,
Somerset, NJ 08873
Telephone [phone]
Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Telephone [phone]
www.bodine.com
The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract.