User Instructions

ManualsBrandsPhilio Technology ManualsAir Quality MonitorsAir Quality Multi-Sensor

Air Quality Multi Sensor PAT05

he PAT05 multi-sensor is a device that allows you to check the air quality in your

home, as well as detect temperature and humidity. The PAT05 Multi-sensor is easy to

use and very convenient for your home. Just set the sensor on the wall of the rooms

you would like to control, and you are ready to go. Moreover, the PAT05 can be

integrated to other Z-Wave certified devices, and controlled with Philio app “Home

Mate 2.” You can now protect your family and make sure there are no gas leaks or

moisture that can harm those you love the most. Set up your PAT05 to send regular

notifications and take control even when not at home.

This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-

Wave Plus messages to communicate to other security enabled Z-Wave Plus

products. Z-WaveTM enabled devices displaying the Z-WaveTM logo can also be

used with it regardless of the manufacturer, and ours can also be used in other

manufacturer’s Z-WaveTM enabled networks.

The product supports Over The Air(OTA) feature for the products firmware upgrade.

This product can be included and operated in any Z-Wave

network with other Z-

Wave

certified devices from other manufacturers and/or other applications. All non-

battery operated nodes within the network will act as repeaters regardless of vendor

to increase reliability of the network.

The device adopt the Z-Wave

500 series chip, when your Z-Wave

network system

is all made by Z-Wave

500 series devices. The network system will have the

advantages as below.

Notice:

Once you have completed the setup process, Please allow for a 7-Day settling period

for the sensors to adjust to their new environment and to observe a typical cycle of air

quality, based on your activity within a 1 week period.

Add to/Remove from Z-Wave

Network

There are two tamper keys in the device, one is in the back side, another is in the

front side. Both of them can add, remove, reset or association from Z-Wave

network.

The table below lists an operation summary of basic Z-Wave functions. Please refer

to the instructions for your Z-WaveTM Certificated Primary Controller to access the

Setup function, and to Add/Remove/associate devices

Notice: Including a node ID allocated by Z-Wave

Controller means “Add” or

“Inclusion”. Excluding a node ID allocated by Z-Wave

Controller means

“Remove” or “Exclusion”.

Function

Description

Add

(Inclusion)

Have Z-Wave

Controller entered inclusion mode.

Summary of content (7 pages)

PAGE 1
Air Quality Multi Sensor PAT05 This product can be included and operated in any Z-Wave TM network with other ZWaveTM certified devices from other manufacturers and/or other applications. All nonbattery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. The device adopt the Z-WaveTM 500 series chip, when your Z-WaveTM network system is all made by Z-WaveTM 500 series devices. The network system will have the advantages as below.
PAGE 2
Remove (Exclusion) Reset SmartStart node ID allocated by Z-Wave Controller means exclusion. Failed or success in including/excluding the node ID can be viewed from the ZWave Controller. 2. Pressing tamper key three times within 2 seconds to enter the inclusion mode. 3. After add successful, the device will wake to receive the setting command from Z-WaveTM Controller about 20 seconds. 1. Have Z-WaveTM Controller entered exclusion mode. 2.
PAGE 3
* Timing Report: Beside the event triggered could report message, the device also support the timing unsolicited report of the status. • eCO2 report: Every 3 minute report once in default. It could be changed by setting the configuration NO. 14. • TVOC report: Every 6 hours report once in default. It could be changed by setting the configuration NO. 15. Notice: The configuration NO. 14 and 15 could be setting to zero to disable the auto report. And the configuration NO.
PAGE 4
NO . 3 Name Def. Valid eCO2 Threshold line 1 6 1 ~ 100 eCO2 difference return: The Unit is 100ppm. 0 means turn off eCO2 detected function. 4 eCO2 Threshold line 2 5 eCO2 Threshold line 3 6 eCO2 Threshold line 4 7 eCO2 Threshold line 5 8 10 16 30 8 TVOC Threshold line 1 9 TVOC Threshold line 2 2 TVOC Threshold line 3 6 10 11 TVOC Threshold line 4 TVOC 12 Threshold line 5 13 (*) Customer Function 1 Name Def. Valid Description range is from 0x00 ~ 0xFF.
PAGE 5
NO . Name Def. Valid 0 means turn off this function. The unit is percentage. Enable this function the device will detect every percentage. And when the lightSensor is over 10 percentage, it will continue report. Differential percent Report 18 TVOC Differential percent Report Description 10 The TVOC Differential to report. 0 means turn off this function. The unit is percentage. 1~100% Enable this function the device will detect every percentage.
PAGE 6
Disposal This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
PAGE 7
FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.